Infiniti QX60/JX - 2018 Fuse Box Diagram

Infiniti QX60/JX - 2018 Fuse Box Diagram

VQ35DD engine
1.
Power steering fluid reservoir
(P. 8-9)
2.
Engine coolant reservoir (P. 8-4)
3.
Drive belt location (P. 8-15)
4.
Fuse box (P. 8-20)
5.
Engine oil filler cap (P. 8-6)
6.
Brake fluid reservoir (P. 8-10)
7.
Air cleaner (P. 8-16)
8.
Fuse box (P. 8-20)
9.
Fuse/Fusible link box (P. 8-20)
10.
Battery (P. 8-12)
11.
Engine oil dipstick (P. 8-6)
12.
Radiator cap (P. 8-4)
13.
Windshield-washer fluid reservoir
(P. 8-11)
Refer to the page number indicated in paren-
theses for operating details.
LDI3131
ENGINE COMPARTMENT CHECK
LOCATIONS
0-8
Illustrated table of contents
VEHICLE INFORMATION
DISPLAY WARNINGS AND
INDICATORS
1. No Key Detected
2. Key ID Incorrect
3. Key Battery Low
4. I-Key
System
Error:
See
Owner’s
Manual
5. Key Registration Complete
6. Push brake and start switch to drive
7. Push Ignition to OFF
8. Shift to Park
9. Engine start operation for Intelligent Key
system (if I-Key battery level is low)
10. Release Parking Brake
11. Low Fuel
12. Loose Fuel Cap
13. Low Oil Pressure: See Owner’s Manual
14. Low Washer Fluid
15. Tire Pressure Low - Add Air
16. TPMS Error: See Owner’s Manual
17. AWD Error: See Owner’s Manual (if so
equipped)
18. AWD High Temp. Stop vehicle (if so
equipped)
19. Tire Size Incorrect: See Owner’s Manual
(if so equipped)
20. Door Open
21. Liftgate Open
22. Timer Alert – Have a break?
23. Low Outside Temperature
24. Power will turn off to save the battery
25. Turn off the lights
26. Parking
Sensor
Error:
See
Owner’s
Manual
27. Predictive
Forward
Collision
Warning
(PFCW) indicator (if so equipped)
28. Lane Departure Warning (LDW) indica-
tor (if so equipped)
29. Blind Spot Warning (BSW) and Rear
Cross Traffic Alert (RCTA) indicator (if so
equipped)
30. Malfunction: See Owner’s Manual (if so
equipped)
31. Intelligent Cruise Control (ICC) indica-
tors (if so equipped)
32. Cruise control indicators (if so equipped)
33. INFINITI Drive Mode Selector indicators
34. Unavailable:
Road
is
slippery
(if
so
equipped)
35. Unavailable: Snow Mode Active (if so
equipped)
36. Unavailable: VDC OFF (if so equipped)
37. Unavailable: High Cabin Temp. (if so
equipped)
38. Unavailable: Side Radar Obstruction (if
so equipped)
39. Unavailable: High Accelerator Temp. (if
so equipped)
40. Unavailable: Front Radar Obstruction (if
so equipped)
41. BCI OFF (if so equipped)
42. Shipping Mode On Push Storage Fuse
43. CVT Error: See Owner’s Manual
44. Rear Door Alert is activated
45. Check Back Seat For All Articles
2-26
Instruments and controls
Departure Prevention (LDW)”, “Lane Depar-
ture Prevention (LDP)” or “Blind Spot Inter-
vention® (BSI)” in the “Starting and driving”
section of this manual.
Unavailable: Side Radar Obstruction (if so
equipped)
This message appears when the Blind Spot
Warning (BSW), Rear Cross Traffic Alert
(RCTA), Blind Spot Intervention® (BSI), or
Backup Collision Intervention systems be-
come unavailable because a radar blockage is
detected. For additional information, refer to
“Blind Spot Warning (BSW)”, “Rear Cross
Traffic Alert (RCTA)”, “Blind Spot Interven-
tion® (BSI)”, or “Backup Collision Interven-
tion” in the “Starting and driving” section of
this manual.
Unavailable: High Accelerator Temp. (if so
equipped)
This message appears when the Backup Col-
lision Intervention (BCI) system becomes un-
available because of an interior temperature
greater than approximately 104°F (40°C).
For additional information, refer to “Backup
Collision Intervention (BCI)” in the “Starting
and driving” section of this manual.
Unavailable: Front Radar Obstruction (if so
equipped)
This message appears when the Intelligent
Cruise Control (ICC), Distance Control Assist
(DCA), Forward Emergency Braking (FEB)
with Pedestrian Detection, or Predictive For-
ward Collision Warning (PFCW) systems be-
come unavailable because the front radar is
obstructed. For additional information, refer
to “Intelligent Cruise Control (ICC)”, “Distance
Control Assist (DCA)”, “Forward Emergency
Braking (FEB) with Pedestrian Detection”, or
“Predictive
Forward
Collision
Warning
(PFCW)” in the “Starting and driving” section
of this manual.
BCI OFF (if so equipped)
This message appears when the Backup Col-
lision Intervention (BCI) system is turned off
using the BCI switch. For additional informa-
tion, refer to “Backup Collision Intervention
(BCI)” in the “Starting and driving” section of
this manual.
Shipping Mode On Push Storage Fuse
This warning may appear if the extended
storage switch is not pushed in. When this
warning appears, push in the extended stor-
age switch to turn off the warning. For addi-
tional information, refer to “Extended stor-
age switch” in this section.
CVT Error: See Owner’s Manual
This warning illuminates when there is a
problem with the CVT system. If this warning
comes on, have the system checked. It is rec-
ommended that you visit an INFINITI retailer
for this service.
Rear Door Alert is activated
When the system is enabled, this message
appears when the rear door alert system is
active and can remind the driver to check the
back seat.
Using the steering wheel switch, a driver
can select “Dismiss Message” to clear the
display for a period of time. If no selection
is made, this message automatically turns
off after a period of time.
Using the steering wheel switch, a driver
can select “Disable Alert” to disable the
horn alert for the remainder of the cur-
rent trip.
Instruments and controls
2-31
CAUTION
∙ The outlet and plug may be hot during or
immediately after use.
∙ Only certain power outlets are designed
for use with a cigarette lighter unit. Do
not use any other power outlet for an
accessory lighter. It is recommended that
you visit an INFINITI retailer for addi-
tional information.
∙ Do not use with accessories that exceed a
12 volt, 120W (10A) power draw.
∙ Do not use double adapters or more than
one electrical accessory.
∙ Use power outlets with the engine run-
ning to avoid discharging the vehicle
battery.
∙ Avoid using power outlets when the air
conditioner, headlights or rear window
defroster is on.
∙ Before inserting or disconnecting a plug,
be sure the electrical accessory being
used is turned OFF.
∙ Push the plug in as far as it will go. If good
contact is not made, the plug may over-
heat or the internal temperature fuse
may open.
∙ When not in use, be sure to close the cap.
Do not allow water or any other liquid to
contact the outlet.
120V OUTLET (if so equipped)
CAUTION
∙ The outlet and plug may be hot during or
immediately after use.
∙ Use power outlets with the engine run-
ning to avoid discharging the vehicle
battery.
∙ Do not use accessories that exceed a
120V, 150W power draw. Do not use
double adaptors or more than one elec-
trical accessory.
Cargo Area
LIC2236
2nd Row
LIC2215
Instruments and controls
2-55
∙ Avoid using power outlets when the air
conditioner, headlights or rear window
defroster is on.
∙ Before inserting or disconnecting a plug,
be sure the electrical accessory being
used is turned OFF.
∙ Push the plug in as far as it will go. If good
contact is not made, the plug may over-
heat or the internal temperature fuse
may open.
∙ When not in use, be sure to close the cap.
Do not allow water or any other liquid to
contact the outlet.
The extended storage switch is pulled out
when in transit from the factory to the re-
tailer. It is located in the fuse panel to the left
of
the
steering
wheel
on
the
instrument
panel. If any electrical equipment does not
operate, ensure the extended storage switch
is pushed fully in place, as shown.
LDI2758
Pulled position
LIC3266
EXTENDED STORAGE SWITCH
2-56
Instruments and controls
Confirming memory storage
Push the SET switch.
If a memory position has been stored in
the switch (1 or 2) then the indicator light
for the respective switch will stay ON for
approximately 5 seconds.
Linking a key fob to a stored
memory position
Each key fob can be linked to a stored
memory position (memory switch 1 or 2) with
the following procedure.
1. Follow steps 1-3 in the “Memory storage
function” section for storing the memory
position.
2. The
indicator
light
for
the
pushed
memory switch will come ON. While the
indicator light is ON for 5 seconds, press
the
button on the key fob. The
hazard lights will flash twice. The indica-
tor light of the linked memory switch will
blink and click twice. After the indicator
light goes off, the key fob is linked to that
memory setting.
Once it is linked, when the ignition switch is
placed
in
the
OFF
position,
pressing
the
button on the key fob will move the
driver’s seat, steering wheel and outside mir-
rors to the linked memory switch position.
NOTE:
If a new memory position is stored in the
linked memory switch, then the key fob will
link the new position and overwrites the pre-
vious position.
ENTRY/EXIT FUNCTION
This system is designed so that the driver’s
seat and automatic operation steering col-
umn will automatically move when the shift
lever is in the P (Park) position. This allows the
driver to get into and out of the driver’s seat
more easily.
The driver’s seat will slide backward and the
steering column will move up:
When the driver’s door is opened with the
ignition switch placed in the OFF posi-
tion.
When the ignition switch is changed from
ACC to OFF with the driver’s door open.
The driver’s seat and steering wheel will re-
turn to the previous position:
When the ignition switch is changed from
ACC or ON while the shift lever is in the P
(Park) position.
The entry/exit function can be adjusted or
canceled through the vehicle settings in the
vehicle information display by performing the
following:
Switch the Exit Seat Slide from ON to
OFF.
Switch the Exit Steering UP from ON to
OFF.
Restarting the entry/exit function
If the battery cable is disconnected, or if the
fuse opens, the stored memory positions will
be lost and some of the functions will be
restricted:
1. Drive the vehicle over 25 mph (40 km/h).
OR
2. Open and close the driver’s door more
than two times with the ignition switch
in the OFF position.
The entry/exit function should now work
properly.
3-40
Pre-driving checks and adjustments
VQ35DD engine
1.
Power steering fluid reservoir
2.
Engine coolant reservoir
3.
Drive belt location
4.
Fuse box
5.
Engine oil filler cap
6.
Brake fluid reservoir
7.
Air cleaner
8.
Fuse box
9.
Fuse/Fusible link box
10.
Battery
11.
Engine oil dipstick
12.
Radiator cap
13.
Windshield-washer fluid reservoir
NOTE:
Some engine covers removed for clarity.
LDI3131
ENGINE COMPARTMENT CHECK
LOCATIONS
Do-it-yourself
8-3
ENGINE COMPARTMENT
WARNING
Never use a fuse of higher or lower amper-
age rating than that specified on the fuse
box cover. This could damage the electrical
system or electronic control units or cause a
fire.
If any electrical equipment does not come on,
check for an open fuse.
1. Be sure the ignition switch and the head-
light switch are OFF.
2. Open the engine hood.
3. Remove the fuse box cover by pushing
the tab and lifting the cover up.
4. Remove the fuse with the fuse puller.
The fuse puller is located in the fuse
block in the passenger compartment.
5. If the fuse is open
±
A
, replace it with a
new fuse
±
B
.
6. If a new fuse also opens, have the elec-
trical system checked and repaired. It is
recommended that you visit an INFINITI
retailer for this service.
Fusible links
If the electrical equipment does not operate
and fuses are in good condition, check the
fusible links. If any of these fusible links are
melted, replace with only Genuine NISSAN
parts.
LDI3117
LDI0456
FUSES
8-20
Do-it-yourself
PASSENGER COMPARTMENT
WARNING
Never use a fuse of higher or lower amper-
age rating than that specified on the fuse
box cover. This could damage the electrical
system or electronic control units or cause a
fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch and the head-
light switch are OFF.
2. Pull the fuse box cover to remove.
3. Remove the fuse with the fuse puller.
4. If the fuse is open
±
A
, replace it with an
equivalent good fuse
±
B
.
5. Push the fuse box cover to install.
6. If a new fuse also opens, have the elec-
trical system checked and repaired. It is
recommended that you visit an INFINITI
retailer for this service.
LDI2092
LDI0456
Do-it-yourself
8-21
2. Locate the jumper harness connector
under the lower portion of the instru-
ment panel. The connector is taped to
the wiring harness
±
1
as indicated.
The connector is marked with a white tag
with “elec brake conn”.
Wire
color
designation
for
electric
trailer
brake controller jumper harness.
WIRE COLOR
NOTE
RED/GREEN
Vehicle stop lamp
switch to trailer brake
controller.
BLACK
Brake controller ground
(-).
BROWN/WHITE
Trailer brake controller
switched output.
RED/BLUE
Not used
RED
Fused trailer brake con-
troller battery feed (B+).
3. Peel off the tape and connect the jumper
harness to the connector.
4. Release the parking brake.
5. Install
the
aftermarket
electric
trailer
brake controller according to the manu-
facturer’s instructions.
Pre-towing tips
Be certain your vehicle maintains a level
position when a loaded and/or unloaded
trailer is hitched. Do not drive the vehicle
if it has an abnormal nose-up or nose-
down
condition;
check
for
improper
tongue load, overload, worn suspension
or other possible causes of either condi-
tion.
Connector Location
LTI2045
Connector
LTI2046
10-26
Technical and consumer information