Nissan Pathfinder - 2018 Fuse Box Diagram

Nissan Pathfinder - 2018 Fuse Box Diagram

VQ35DD engine
1.
Power steering fluid reservoir
(P. 8-10)
2.
Engine coolant reservoir (P. 8-5)
3.
Drive belt location (P.8-15)
4.
Fuse box (P. 8-21)
5.
Engine oil filler cap (P. 8-7)
6.
Brake fluid reservoir (P. 8-11)
7.
Air cleaner (P. 8-17)
8.
Fuse box (P. 8-21)
9.
Fuse/Fusible link box (P. 8-21)
10.
Battery (P. 8-13)
11.
Engine oil dipstick (P. 8-7)
12.
Radiator cap (P. 8-5)
13.
Windshield-washer fluid reservoir
(P. 8-12)
Refer to the page number indicated in
parentheses for operating details.
LDI3131
ENGINE COMPARTMENT CHECK
LOCATIONS
0-8
Illustrated table of contents
VEHICLE INFORMATION DISPLAY
WARNINGS AND INDICATORS
1. No Key Detected
2. Key ID Incorrect
3. Key low battery
4. I-Key System Error: See Owner’s
Manual
5. Key Registration Complete
6. Shift to Park
7. Push Ignition to OFF
8. Push brake and start switch to drive
9. Engine start operation for Intelligent
Key system (if I-Key battery is low)
10. Release Parking Brake
11. Low Fuel
12. Loose Fuel Cap
13. Low Oil Pressure: See Owner’s Manual
14. Low Washer Fluid
15. Tire Pressure Low - Add Air
16. TPMS Error: See Owner’s Manual
17. Intelligent 4x4 indicators (if so equipped)
18. 4WD Error: See Owner’s Manual
(if so equipped)
19. Door Open
20. Liftgate Open
21. Timer Alert – Have a break?
22. Low Outside Temperature
23. Power will turn off to save the battery
24. Power turned off to save the battery
25. Turn off the lights
26. Headlight System Error: See Owner’s
Manual (if so equipped)
27. Parking Sensor Error: See Owner’s
Manual (if so equipped)
28. Blind Spot Warning (BSW) and Rear
Cross Traffic Alert (RCTA) indicator
(if so equipped)
29. Malfunction: See Owner’s Manual
(if so equipped)
30. Side Radar Obstruction (if so equipped)
31. Cruise control indicator (if so equipped)
32. Intelligent Cruise Control (ICC)
indicator (if so equipped)
33. Shipping Mode On Push Storage Fuse
34. Transmission Shift Position indicator
35. CVT Error: See Owner’s Manual
36. Unavailable: Front Radar Obstruction
(if so equipped)
37. Rear Door Alert is activated
38. Check Back Seat For All Articles
39. Automatic Emergency Braking (AEB)
indicator light
No Key Detected
This warning appears when the Intelligent
Key is left outside the vehicle with the igni-
tion switch in the ON position. Make sure
the Intelligent Key is inside the vehicle.
For additional information, refer to “NISSAN
Intelligent Key®” in the “Pre-driving checks
and adjustments” section of this manual.
Key ID Incorrect
This warning appears when the ignition
switch is placed from the OFF position and
the Intelligent Key is not recognized by the
system. You cannot start the engine with
an unregistered key.
For additional information, refer to “NISSAN
Intelligent Key®” in the “Pre-driving checks
and adjustments” section of this manual.
Instruments and controls
2-29
When cruise control is activated, a green
circle will illuminate to indicate it is set. The
vehicle information display will also display
the speed the cruise control was set at. If
you accelerate past the set speed, the
speed will blink until you either cancel
cruise control or go back to the set speed. If
cruise
control
is
on
and
canceled,
the
speed will be displayed to show the speed
the vehicle will return to if the resume but-
ton is activated.
Intelligent Cruise Control (ICC) indicator
(if so equipped)
This indicator shows the Intelligent Cruise
Control (ICC) system status. The status is
shown by the color. For additional informa-
tion, refer to “Intelligent Cruise Control (ICC)”
in the “Starting and driving” section of this
manual.
Shipping Mode On Push Storage Fuse
This warning may appear if the extended
storage switch is not pushed in. When this
warning appears, push in the extended
storage switch to turn off the warning. For
additional information, refer to “Extended
storage switch” in this section.
Transmission Shift Position indicator
This indicator shows the transmission shift
position.
CVT Error: See Owner’s Manual
This warning illuminates when there is a
problem with the CVT system. If this warn-
ing comes on, have the system checked. It
is recommended that you visit a NISSAN
dealer for this service.
Unavailable: Front Radar Obstruction
(if so equipped)
This warning appears when the Intelligent
Cruise Control (ICC) system becomes un-
available because the front radar is ob-
structed. For additional information, refer
to “Intelligent Cruise Control (ICC)” or “Auto-
matic Emergency Braking ” in the “Starting
and driving” section of this manual.
Rear Door Alert is activated
(if so equipped)
When the system is enabled, this message
appears when the rear door alert system is
active and can remind the driver to check
the back seat.
Using the steering wheel switch, a driver
can select “Dismiss Message” to clear
the display for a period of time. If no
selection is made, this message auto-
matically turns off after a period of time.
Using the steering wheel switch, a driver
can select “Disable Alert” to disable the
horn alert for the remainder of the cur-
rent trip.
WARNING
Selecting “Dismiss Message” during a
stop within a trip temporarily dismisses
the message for that stop without turn-
ing the system off. Alerts* can be pro-
vided for other stops during the trip. Se-
lecting “Disable Alert” turns off the Rear
Door Alert system for the remainder of
a
trip
and
no
audible
alert
will
be
provided.
NOTE:
This system is disabled until a driver en-
ables it using the vehicle information
display. For additional information, refer
to “How to use the vehicle information
display” in this section.
For additional information, refer to “Rear
Door Alert” in this section.
Instruments and controls
2-33
CAUTION
∙ The outlet and plug may be hot during
or immediately after use.
∙ Only certain power outlets are de-
signed for use with a cigarette lighter
unit. Do not use any other power out-
let for an accessory lighter. It is rec-
ommended that you visit a NISSAN
dealer for additional information.
∙ Do not use with accessories that ex-
ceed a 12 volt, 120W (10A) power draw.
∙ Do not use double adapters or more
than one electrical accessory.
∙ Use power outlets with the engine
running to avoid discharging the ve-
hicle battery.
∙ Avoid using power outlets when the
air
conditioner,
headlights,
or
rear
window defroster is on.
∙ Before inserting or disconnecting a
plug, be sure the electrical accessory
being used is turned off.
∙ Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.
∙ When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.
Center Console (if so equipped)
LIC3737
Cargo Area (if so equipped)
LIC2236
2-54
Instruments and controls
120V OUTLET (if so equipped)
CAUTION
∙ The outlet and plug may be hot during
or immediately after use.
∙ Use power outlets with the engine
running to avoid discharging the ve-
hicle battery.
∙ Do not use double adaptors or more
than one electrical accessory.
∙ Avoid using power outlets when the
air conditioner,headlights or rear win-
dow defroster is on.
∙ Before inserting or disconnecting a
plug, be sure the electrical accessory
being used is turned off.
∙ Push the plug in as far as it will go. If
good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.
∙ When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.
The extended storage switch is used when
the vehicle is in transit from the factory. It is
located in the fuse panel to the left of the
steering wheel on the instrument panel. If
any electrical equipment does not operate,
ensure the extended storage switch is
pushed fully in place, as shown.
2nd Row
LIC2407
LDI2758
EXTENDED STORAGE SWITCH
Instruments and controls
2-55
If a memory position has been stored in
the switch (1 or 2) then the indicator light
for the respective switch will stay ON for
approximately 5 seconds.
Linking a key fob to a stored
memory position
Each key fob can be linked to a stored
memory position (memory switch 1 or 2)
with the following procedure.
1. Follow steps 1-3 in the “Memory storage
function”
section
for
storing
the
memory position.
2. The
indicator
light
for
the
pushed
memory switch will come ON.While the
indicator light is ON for 5 seconds,
press the
button on the key fob.
The
indicator
light
of
the
linked
memory switch will blink. After the indi-
cator light goes off, the key fob is linked
to that memory setting.
Once it is linked, when the ignition switch is
placed
in
the
OFF
position,
pressing
the
button on the key fob will move
the driver’s seat, steering wheel and out-
side mirrors to the linked memory switch
position.
NOTE:
If a new memory position is stored in the
linked memory switch, then the key fob
will link the new position and overwrites
the previous position.
ENTRY/EXIT FUNCTION
This system is designed so that the driver’s
seat and automatic operation steering col-
umn will automatically move when the
shift lever is in the P (Park) position. This
allows the driver to get into and out of the
driver’s seat more easily.
The driver’s seat will slide backward and
the steering column will move up:
When the driver’s door is opened with
the ignition switch placed in the OFF
position.
When the ignition switch is changed
from ACC to OFF with the driver’s door
open.
The driver’s seat and steering wheel will
return to the previous position:
When the ignition switch is changed
from ACC or ON while the shift lever is in
the P (Park) position.
The entry/exit function can be adjusted or
canceled through the “Vehicle Settings” in
the vehicle information display by perform-
ing the following:
Switch the Exit Seat Slide from ON to
OFF.
Switch the Exit Steering UP from ON to
OFF.
Restarting the entry/exit function
If the battery cable is disconnected, or if the
fuse opens, the stored memory positions
will be lost and some of the functions will
be restricted:
1. Drive the vehicle over 25 mph (40 km/h).
OR
2. Open and close the driver’s door more
than two times with the ignition switch
in the OFF position.
The entry/exit function should now work
properly.
3-48
Pre-driving checks and adjustments
VQ35DD engine
1.
Power steering fluid reservoir
2.
Engine coolant reservoir
3.
Drive belt location
4.
Fuse box
5.
Engine oil filler cap
6.
Brake fluid reservoir
7.
Air cleaner
8.
Fuse box
9.
Fuse/Fusible link box
10.
Battery
11.
Engine oil dipstick
12.
Radiator cap
13.
Windshield-washer fluid reservoir
LDI3131
ENGINE COMPARTMENT CHECK
LOCATIONS
8-4
Do-it-yourself
Under some driving or climate conditions,
occasional brake squeak, squeal or other
noise
may
be
heard. Occasional
brake
noise during light to moderate stops is nor-
mal and does not affect the function or
performance of the brake system.
Proper brake inspection intervals should
be followed.
For additional information re-
garding brake inspections, refer to the ap-
propriate maintenance schedule informa-
tion in the "Maintenance and schedules"
section of this manual.
ENGINE COMPARTMENT
WARNING
Never use a fuse of higher or lower am-
perage rating than that specified on the
fuse box cover. This could damage the
electrical system or electronic control
units or cause a fire.
If any electrical equipment does not come
on, check for an open fuse.
1. Be sure the ignition switch and the
headlight switch are OFF.
2. Open the engine hood.
3. Remove the fuse box cover by pushing
the tab and lifting the cover up.
4. Remove the fuse with the fuse puller.
The fuse puller is located in the fuse
block in the passenger compartment.
LDI3117
FUSES
8-20
Do-it-yourself
5. If the fuse is open
±
A
, replace it with a
new fuse
±
B
.
6. If a new fuse also opens, have the elec-
trical system checked and repaired. It is
recommended that you visit a NISSAN
dealer for this service.
Fusible links
If the electrical equipment does not oper-
ate and fuses are in good condition, check
the fusible links. If any of these fusible links
are
melted,
replace
with
only
Genuine
NISSAN parts.
PASSENGER COMPARTMENT
WARNING
Never use a fuse of higher or lower am-
perage rating than that specified on the
fuse box cover. This could damage the
electrical system or electronic control
units or cause a fire.
If any electrical equipment does not oper-
ate, check for an open fuse.
1. Be sure the ignition switch and the
headlight switch are OFF.
2. Pull the fuse box cover to remove.
3. Remove the fuse with the fuse puller.
4. If the fuse is open
±
A
, replace it with an
equivalent good fuse
±
B
.
5. Reverse step 2 to reinstall the box
cover.
6. If a new fuse also opens, have the elec-
trical system checked and repaired. It is
recommended that you visit a NISSAN
dealer for this service.
LDI0456
LDI2092
LDI0456
Do-it-yourself
8-21
Wire color designation for electric trailer
brake controller jumper harness.
WIRE COLOR
NOTE
RED/GREEN
Vehicle stop lamp
switch to trailer brake
controller.
BLACK
Brake controller
ground (-).
BROWN/WHITE
Trailer brake controller
switched output.
RED/BLUE
Not used
RED
Fused trailer brake
controller battery feed
(B+).
3. Peel
off
the
tape
and
connect
the
jumper harness to the connector.
4. Release the parking brake.
5. Install the aftermarket electric trailer
brake
controller
according
to
the
manufacturer’s instructions.
Pre-towing tips
Be certain your vehicle maintains a level
position when a loaded and/or un-
loaded trailer is hitched. Do not drive the
vehicle if it has an abnormal nose-up or
nose-down
condition; check
for
im-
proper tongue load, overload, worn sus-
pension or other possible causes of ei-
ther condition.
Always secure items in the trailer to pre-
vent load shift while driving.
Keep the cargo load as low as possible
in the trailer to keep the trailer center of
gravity low.
Load the trailer so approximately 60%
of the trailer load is in the front half and
40% is in the back half. Also make sure
the load is balanced side to side.
Check your hitch, trailer tire pressure,
vehicle tire pressure, trailer light opera-
tion, and trailer wheel lug nuts every
time you attach a trailer to the vehicle.
Be certain your rearview mirrors con-
form to all federal, state or local regula-
tions. If not, install any mirrors required
for towing before driving the vehicle.
Determine the overall height of the ve-
hicle and trailer so the required clear-
ance is known.
Trailer towing tips
In order to gain skill and an understanding
of the vehicle’s behavior, you should prac-
tice turning, stopping and backing up in an
area which is free from traffic. Steering sta-
bility
and
braking
performance
will
be
somewhat different than under normal
driving conditions.
Always secure items in the trailer to pre-
vent load shift while driving.
Lock the trailer hitch coupler with a pin
or lock to prevent the coupler from in-
advertently becoming unlatched.
Avoid
abrupt
starts,
acceleration
or
stops.
Avoid sharp turns or lane changes.
Always drive your vehicle at a moderate
speed.
Technical and consumer information
10-27