Honda HR-V - 2018 Fuse Box Diagram

Honda HR-V - 2018 Fuse Box Diagram

104
|
|
105
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
After the Engine Starts
Once your vehicle’s engine has started, remove the jumper cables in the following
order:
1. Disconnect the jumper cable from your vehicle’s stud bolt.
2. Disconnect the other end of the jumper cable from the assisting vehicle’s (-)
terminal.
3. Disconnect the jumper cable from your vehicle’s (+) terminal.
4. Disconnect the other end of the jumper cable from the assisting vehicle’s (+)
terminal.
5. Have your vehicle inspected by a nearby service station or a dealer.
A battery can explode if you do not follow the correct procedure, seriously
injuring anyone nearby.
Keep all sparks, open flames, and smoking materials away from the battery.
WARNING
Jump Starting
Turn off the power to electrical devices, such as audio and lights. Turn off the
engine, then open the hood.
1. Remove the under-hood fuse box cover (see
page 114). Connect the first jumper cable to your
vehicle’s battery (+) terminal.
2. Connect the other end of the first jumper cable
to the booster battery (+) terminal. Use a 12-volt
booster battery only.
3. Connect the second jumper cable to the booster
battery (-) terminal.
4. Connect the other end of the second jumper cable
to the stud bolt as shown. Do not connect this
jumper cable to any other part.
5. If your vehicle is connected to another vehicle,
start the assisting vehicle’s engine and increase its
rpm slightly.
6. Attempt to start your vehicle’s engine. If it turns over slowly, make sure that the
jumper cables have good metal-to-metal contact.
Booster
battery
Learn about what to do in critical or emergency situations.
Smart Entry Remote Battery Strength*
If the battery life in your remote transmitter is weak, follow the below steps to start
the engine.
1. Touch the back of the remote transmitter to the
ENGINE START/STOP button while the indicator is
flashing.
2. With the brake pedal pressed (and the clutch
pedal for manual transmission), press the ENGINE
START/STOP button within 10 seconds.
HANDLING THE UNEXPECTED
*if equipped
Shift Lever Does Not Move*
Follow the procedure below if you cannot move the shift lever out of Park (P).
1. Set the parking brake.
2. Remove the key from the ignition, or remove the
built-in key from the remote transmitter.
3. Wrap a cloth around the tip of a small flat-tip
screwdriver. Put it into the shift lock release slot as
shown in the image, and remove the cover.
4. Insert the key into the shift lock release slot.
5. While pushing the key down, press the shift lever
release button and place the shift lever into Neutral
(N). The lock is now released. Have the shift lever
checked by a dealer as soon as possible.
Slot
Release button
Shift lock
release slot
Cover
Battery posts, terminals, and related accessories contain lead and lead
compounds.
Wash your hands after handling.
WARNING
114
|
|
115
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Fuse box B
Pull up the cover on the + terminal, then remove it while pulling out the tab, as
shown. Replacement of engine compartment fuse boxes should be done by a
dealer.
Circuit Protected
Amps
a
Battery Main
100 A
b
RB Main 1
70 A
c
RB Main 2
80 A
d
CAP Main
70 A
Tab
*if equipped
a
b
c
d
Fuse Locations
If any electrical devices are not working, turn the vehicle off and check to see if any
applicable fuse is blown. Fuse locations are shown on the fuse box cover. Locate the
fuse in question by the fuse number and box cover number.
Engine Compartment Fuse Boxes
Fuse box A
Located under the hood near the brake fluid reservoir. Push the tabs to open the
box.
Circuit Protected
Amps
1
Headlight Low Beam Main
20 A
2
CDC
*
(30 A)
3
Hazard
10 A
4
DBW
15 A
5
Wiper
*
(30 A)
6
Stop
10 A
7
IGP
15 A
8
IG Coil
15 A
9
EOP
*
(10 A)
10
INJ
*
(20 A)
11
VST2
*
(30 A)
12
Main Fan
30 A
13
Starter SW
*
(30 A)
14
MG Clutch
7.5 A
15
Battery Sensor
(7.5 A)
16
Small Light
10 A
17
AFP Main
*
(10 A)
18
Horn
10 A
19
Fog Light
*
(10 A)
20
SBW
*
(10 A)
*if equipped
Tab
Circuit Protected
Amps
21
Back Up Main
10 A
22
Audio
(10 A)
23
Sub Fan
(30 A)
24
VST1
*
(30 A)
25
STRLD
*
(7.5 A)
26
IGP CAM
*
(7.5 A)
27
28
29
Back Up
*
(30 A)
30
IGP LAF
(7.5 A)
31
IGPS
(7.5 A)
32
Right Headlight Low Beam
10 A
33
Left Headlight Low Beam
10 A
116
|
|
117
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Circuit Protected
Amps
1
EPS
70 A
IG Main
30 A
*1
50 A
*2
Fuse Box Main 2
50 A
ABS/VSA Motor
40 A
Fuse Box Main 1
30 A
Fuse Box Main 3 *
40 A
2
Rear Defogger
30 A
EPB L
30 A
IG Main2
*1
*2
30 A
HTR
40 A
EPB R
30 A
*1: Models with smart entry system
*2: Models without smart entry system
3
4
5
ABS/VSA FSR
30 A
6
Deicer
*
(10 A)
7
RR ACC SOCKET
*
(20 A)
8
9
Interior Light
7.5 A
10
ACC Socket (Console)
*
(20 A)
11
-
-
12
*1
-
-
12
*2
ACC Key Lock
(7.5 A)
13
Heated Door Mirror
*
(10 A)
14
A/C Blower SW
*
(7.5 A)
15
*1
15
*2
Wiper
30 A
E±DPS *
30 A
Fuse box B
Located behind the dashboard next to the steering wheel. Remove the cover by
putting a flat-tip screwdriver into the side slot, as shown.
Fuse label
*if equipped
Cover
Circuit Protected
Amps
1
Door Lock
20 A
2
3
Smart
*
(10 A)
4
Driver Side Door Unlock
10 A
5
Passenger Side Door Unlock
10 A
6
Driver Door Unlock
10 A
7
Driver Door Lock
10 A
8
Driver’s Power Window
20 A
9
Passenger’s Power Window
20 A
10
Rear Left Power Window
20 A
11
Rear Right Power Window
20 A
12
Driver Side Door Lock
10 A
13
Passenger Side Door Lock
10 A
14
15
Right Headlight High Beam
10 A
16
STS
*
(7.5 A)
17
Sunshade
*
(20 A)
18
Moonroof
*
(20 A)
19
Front Seat Heater
*
(20 A)
20
Interior Fuse Boxes
Fuse box A
Located behind the dashboard next to the steering wheel.
*if equipped
Fuse label
Circuit Protected
Amps
21
MP Camera
*
(10 A)
22
Washer
15 A
23
Rear Wiper
*
(10 A)
24
A/C
7.5 A
25
Daytime Running Lights
7.5 A
26
Starter Cut
*
(7.5 A)
27
ABS/VSA
7.5 A
28
SRS
10 A
29
Left Headlight High Beam
10 A
30
ACG
10 A
31
IG Relay
10 A
32
Fuel Pump
15 A
33
SRS
(7.5 A)
34
Meter
7.5 A
35
Mission SOL
7.5 A
36
Front ACC Socket
20 A
37
ACC
(7.5 A)
38
ACC
*
(7.5 A)
39
Option
10 A
40
Rear Wiper
10 A
41
-
-
42
-
-
118
|
|
119
MAINTENANCE
HANDLING THE UNEXPECTED
Learn about basic maintenance that you can perform on the vehicle yourself, as well
as information about how to best maintain the vehicle.
Safety Precautions
Some of the most important safety precautions are listed below; however, we cannot
warn you of every conceivable hazard that can arise in performing maintenance.
Only you can decide whether or not you should perform a given task.
Maintenance Safety
• To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames
away from the battery and all fuel-related parts.
• Never leave rags, towels, or other flammable objects under the hood. Heat from
the engine and exhaust can ignite them, causing a fire.
• To clean parts, use a commercially available degreaser or parts cleaner, not
gasoline.
• Wear eye protection and protective clothing when working with the battery or
compressed air.
• Do not run the engine in confined spaces where carbon monoxide gas can
accumulate.
Vehicle Safety
• The vehicle must be stationary, and parked on level ground with the parking
brake set and the engine off.
• Be aware that hot parts can burn you.
• Be aware that moving parts can injure you.
MAINTENANCE
Improperly maintaining this vehicle or failing to correct a problem before
driving can cause a crash in which you can be seriously hurt or killed.
Always follow the inspection and maintenance recommendations according
to the schedules in this guide.
WARNING
Failure to properly follow maintenance instructions and precautions can
cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this guide.
WARNING
Inspecting and Changing Fuses
1. Turn the vehicle off, including all lights and
accessories.
2. Check the fuses on the battery in the engine
compartment. If the fuse is blown, have it
replaced by a dealer.
3. Remove the fuse box cover.
4. Inspect the small fuses in the engine
compartment and the vehicle interior.
If there is a blown fuse, remove it with the fuse
puller and replace it with a new one.
5. Check the large fuse in the engine compartment.
If the fuse is blown, use a Phillips-head
screwdriver to remove the screw and replace the
fuse with a new one. Reinstall the screw.
Replacing a fuse with one that has a higher rating greatly increases the chances of
damaging the electrical system.
NOTICE
Blown fuse
Fuse box on battery
Fuse puller
Combined fuse
Blown fuse
Contents
This owner’s manual should be considered a permanent part of the
vehicle and should remain with the vehicle when it is sold.
This owner’s manual covers all models of your vehicle. You may find
descriptions of equipment and features that are not on your
particular model.
Images throughout this owner’s manual (including the front cover)
represent features and equipment that are available on some, but
not all, models. Your particular model may not have some of these
features.
This owner’s manual is for vehicles sold in the United States and
Canada.
The information and specifications included in this publication were
in effect at the time of approval for printing. Honda Motor Co., Ltd.
reserves the right, however, to discontinue or change specifications
or design at any time without notice and without incurring any
obligation.
2
Safe Driving
P. 29
For Safe Driving P. 30
Seat Belts P. 35
Airbags P. 44
2
Instrument Panel
P. 73
Indicators P. 74
Gauges and Displays P. 90
2
Controls
P. 95
Clock P. 96
Locking and Unlocking the Doors P. 98
Opening and Closing the Windows P. 121
Operating the Switches Around the Steering Wheel P. 124
Interior Lights/Interior Convenience Items P. 152
2
Features
P. 177
Audio System P. 178
Audio System Basic Operation P. 184, 205
Customized Features P. 252
Bluetooth
®
HandsFreeLink
®
P. 274, 297
2
Driving
P. 327
Before Driving P. 328
Towing a Trailer P. 333
Parking Your Vehicle P. 385
Multi-View Rear Camera P. 386
2
Maintenance
P. 391
Before Performing Maintenance P. 392
Maintenance Minder
TM
P. 395
Checking and Maintaining Wiper Blades P. 419
Heating and Cooling System
*
/Climate Control System
*
Maintenance P. 437
2
Handling the Unexpected
P. 445
Tools P. 446
If a Tire Goes Flat P. 448
Overheating P. 463
Indicator, Coming On/Blinking P. 465
Fuses P. 470
2
Information
P. 479
Specifications P. 480
Identification Numbers P. 482
Emissions Testing P. 485
Warranty Coverages P. 487
Visual Index
6
Quick Reference Guide
Electric Parking Brake Switch
(P377)
Hood Release Handle
(P400)
Fuel Fill Door Release Handle
(P389)
Passenger’s Front Airbag
(P47)
Interior Fuse Boxes
(P472)
Driver’s Front Airbag
(P47)
Power Window Switches
(P121)
Power Door Lock Master Switch
(P109)
Door Mirror Controls
(P141)
Automatic Brake Hold Button
(P380)
Seat Heater Icons
*
(P162)
Glove Box
(P154)
Accessory Power Socket
(P158)
USB Port(s)
(P179)
HDMI
®
Port
*
(P180)
Auxiliary Input Jack
*
(P180)
Shift Lever
Continuously Variable
Transmission
*
(P348,°350)
Manual Transmission
*
(P354)
24
Quick Reference Guide
Handling the Unexpected
(P445)
Flat Tire
(P448)
Park in a safe location and replace the
flat tire with the compact spare tire in the
cargo area.
Indicators Come On
(P465)
Identify the indicator and consult the
owner’s manual.
Engine Won’t Start
(P457)
If the battery is dead, jump start using a
booster battery.
Blown Fuse
(P470)
Check for a blown fuse if an electrical
device does not operate.
Overheating
(P463)
Park in a safe location. If you do not see
steam under the hood, open the hood,
and let the engine cool down.
Emergency Towing
(P475)
Call a professional towing service if you
need to tow your vehicle.
Continued
335
uu
Towing a Trailer
u
Towing Your Vehicle
Driving
Extended towing
If you tow more than eight hours in one day, you should repeat the “When Your
Vehicle is Towed Behind a Motorhome” at least every eight hours.
You also need to perform the following procedure to prevent the battery from
running down.
1.
Remove the 20 A accessory power socket
and 7.5 A ACC fuses. These fuses are
located in the interior fuse box.
2
Interior Fuse Boxes
P. 472
2.
Remove the 10 A Back up fuse. This fuse is
located in the engine compartment fuse
box.
2
Engine Compartment Fuse Box
P. 470
3.
Store the fuses in a safe place so you do not
lose them.
u
Make sure to reinstall the fuses before
you start driving your vehicle.
4.
Shift to
(
N
.
5.
Turn the ignition switch to ACCESSORY
(
q
.
u
Make sure the steering wheel does not
lock.
1
Towing Your Vehicle
Make sure to reinstall the fuses before you start
driving your vehicle.
Engine Compartment Fuse Box
10 A Back Up Fuse
Interior Fuse Box
20 A Accessory
Power Socket Fuse
7.5 A ACC fuse
Models without smart entry system
336
uu
Towing a Trailer
u
Towing Your Vehicle
Driving
1.
Remove the 20 A accessory power socket and 7.5 A ACC fuses. These fuses are located in the
interior fuse box.
2
Interior Fuse Boxes
P. 472
2.
Remove the 10 A Back up fuse. This fuse is located in the engine compartment fuse box.
2
Engine Compartment Fuse Box
P. 470
3.
Store the fuses in a safe place so you do not lose them.
u
Make sure to reinstall the fuses before you start driving your vehicle.
4.
Push the
ENGINE START/STOP
button without depressing the clutch pedal.
u
The indicator on the
ENGINE START/STOP
button blinks.
5.
Touch the center of the
ENGINE START/STOP
button with the
H
logo on the smart entry remote
while the indicator is blinking.
u
The indicator stop blinking, then stays on.
6.
Shift to
(
N
.
7.
Push the
ENGINE START/STOP
button once without depressing the clutch pedal.
u
Make sure the steering wheel does not lock.
Engine Compartment Fuse Box
10 A Back Up Fuse
Interior Fuse Box
20 A Accessory
Power Socket Fuse
7.5 A ACC fuse
Models with smart entry system
443
Maintenance
Accessories and Modifications
Accessories
When installing accessories, check the following:
Do not install accessories on the windshield. They can obstruct your view and
delay your reaction to driving conditions.
Do not install any accessories over areas marked
SRS AIRBAG
, on the sides or
backs of the front seats, on front or side pillars, or near the side windows.
Accessories installed in these areas may interfere with proper operation of the
vehicle’s airbags or may be propelled into you or another occupant if the airbags
deploy.
Be sure electronic accessories do not overload electrical circuits or interfere with
proper operation of your vehicle.
2
Fuses
P. 470
Before installing any electronic accessory, have the installer contact a dealer for
assistance. If possible, have a dealer inspect the final installation.
1
Accessories and Modifications
Honda Genuine accessories are recommended to
ensure proper operation on your vehicle.
3
WARNING
Improper accessories or modifications can
affect your vehicle’s handling, stability, and
performance, and cause a crash in which
you can be seriously hurt or killed.
Follow all instructions in this owner’s
manual regarding accessories and
modifications.
457
Handling the Unexpected
Engine Does Not Start
Checking the Engine
If the engine does not start, check the starter.
Starter condition
Checklist
Starter doesn’t turn or turns
over slowly.
The battery may be dead. Check
each of the items on the right and
respond accordingly.
Check the brightness of the interior lights.
Turn on the interior lights and check the brightness.
If the interior lights are dim or do not come on at all
2
Battery
P. 433
If the interior lights come on normally
2
Fuses
P. 470
The starter turns over normally
but the engine doesn’t start.
There may be a problem with the
fuse. Check each of the items on
the right and respond accordingly.
Review the engine start procedure.
Follow its instructions, and try to start the engine again.
2
Starting the Engine
P. 339, 342
Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
2
Immobilizer System
P. 118
Check the fuel level.
There should be enough fuel in the tank.
2
Fuel Gauge
P. 93
Check the fuse.
Check all fuses, or have your vehicle checked by a dealer.
2
Inspecting and Changing Fuses
P. 474
If the problem continues:
2
Emergency Towing
P. 475
1
Checking the Engine
If you must start the vehicle immediately, use an
assisting vehicle to jump start it.
2
Jump Starting
P. 460
460
Handling the Unexpected
Jump Starting
Turn off the power to electric devices, such as audio and lights. Turn off the engine,
then open the hood.
1.
Connect the first jumper cable to your
vehicle’s battery
+
terminal.
u
Remove the cover from the under-hood
fuse box.
2
Engine Compartment Fuse Box
P. 470
2.
Connect the other end of the first jumper
cable to the booster battery
+
terminal.
u
Use a 12-volt booster battery only.
u
Connect when using the automotive
battery charger to boost your 12-volt
battery, select a lower charging voltage
than 15-volt. Check the charger manual
for the proper setting.
3.
Connect the second jumper cable to the
booster battery
-
terminal.
4.
Connect the other end of the second
jumper cable to the stud bolt as shown. Do
not connect this jumper cable to any other
part.
5.
If your vehicle is connected to another
vehicle, start the assisting vehicle’s engine
and increase its rpm slightly.
6.
Attempt to start your vehicle’s engine. If it
turns over slowly, check that the jumper
cables have good metal-to-metal contact.
Jump Starting Procedure
1
Jump Starting
Securely attach the jumper cables clips so that they
do not come off when the engine vibrates. Also be
careful not to tangle the jumper cables or allow the
cable ends to touch each other while attaching or
detaching the jumper cables.
Battery performance degrades in cold conditions and
may prevent the engine from starting.
3
WARNING
A battery can explode if you do not follow
the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the battery.
Booster
Battery
470
Handling the Unexpected
Fuses
Fuse Locations
If any electrical devices are not working,
turn the ignition switch to LOCK
(
0
*1
and
check to see if any applicable fuse is blown.
Fuse box A
Located near the brake fluid reservoir. Push
the tabs to open the box.
Fuse locations are shown on the fuse box
cover. Locate the fuse in question by the
fuse number and box cover number.
Engine Compartment Fuse Box
Tab
Circuit protected and fuse rating
Circuit Protected
Amps
1
Headlight Low Beam Main
20 A
2
CDC
*
(30 A)
3
Hazard
10 A
4
DBW
15 A
5
Wiper
*
(30 A)
6
Stop
10 A
7
IGP
15 A
8
IG Coil
15 A
9
EOP
*
(10 A)
10
INJ
*
(20 A)
11
VST2
*
(30 A)
12
Main Fan
30 A
13
Starter SW
*
(30 A)
14
MG Clutch
7.5 A
15
Battery Sensor
(7.5 A)
16
Small Light
10 A
17
AFP Main
*
(10 A)
18
Horn
10 A
19
Fog Light
*
(10 A)
20
SBW
*
(10 A)
*1:Models with the smart entry system have
an
ENGINE START/STOP
button
instead of an ignition switch.
Circuit Protected
Amps
21
Back Up Main
10 A
22
Audio
(10 A)
23
Sub Fan
(30 A)
24
VST1
*
(30 A)
25
STRLD
*
(7.5 A)
26
IGP CAM
*
(7.5 A)
27
28
29
Back Up
*
(30 A)
30
IGP LAF
(7.5 A)
31
IGPS
(7.5 A)
32
Right Headlight Low Beam
10 A
33
Left Headlight Low Beam
10 A
* Not available on all models
471
uu
Fuses
u
Fuse Locations
Continued
Handling the Unexpected
Fuse box B
Tab
a
b
c
d
Pull up the cover on the
+
terminal, then
remove it while pulling out the tab as
shown.
Replacement of engine compartment fuses
should be done by a dealer.
Circuit protected and fuse rating
Circuit Protected
Amps
a
Battery Main
100 A
b
RB Main 1
70 A
c
RB Main 2
80 A
d
CAP Main
70 A
472
uu
Fuses
u
Fuse Locations
Handling the Unexpected
Fuse box A
Located behind the instrument panel.
Fuse locations are shown on the label under
the steering column.
Locate the fuse in question by the fuse
number and label number.
Interior Fuse Boxes
Fuse Label
Circuit protected and fuse rating
Circuit Protected
Amps
1
Door Lock
20 A
2
3
Smart
*
(10 A)
4
Driver Side Door Unlock
10 A
5
Passenger Side Door Unlock
10 A
6
Driver Door Unlock
10 A
7
Driver Door Lock
10 A
8
Driver’s Power Window
20 A
9
Passenger’s Power Window
20 A
10
Rear Left Power Window
20 A
11
Rear Right Power Window
20 A
12
Driver Side Door Lock
10 A
13
Passenger Side Door Lock
10 A
14
15
Right Headlight High Beam
10 A
16
STS
*
(7.5 A)
17
Sunshade
*
(20 A)
18
Moonroof
*
(20 A)
19
Front Seat Heater
*
(20 A)
20
Circuit Protected
Amps
21
MP Camera
*
(10 A)
22
Washer
15 A
23
Rear Wiper
*
(10 A)
24
A/C
7.5 A
25
Daytime Running Lights
7.5 A
26
Starter Cut
*
(7.5 A)
27
ABS/VSA
7.5 A
28
SRS
10 A
29
Left Headlight High Beam
10 A
30
ACG
10 A
31
IG Relay
10 A
32
Fuel Pump
15 A
33
SRS
(7.5 A)
34
Meter
7.5 A
35
Mission SOL
7.5 A
36
Front ACC Socket
20 A
37
ACC
(7.5 A)
38
ACC
*
(7.5 A)
39
Option
10 A
40
Rear Wiper
10 A
41
42
* Not available on all models
473
uu
Fuses
u
Fuse Locations
Handling the Unexpected
Fuse box B
Remove the cover by putting the flat-tip
screwdriver into the side slot as shown.
Fuse Label
Cover
Circuit protected and fuse rating
Circuit Protected
Amps
1
EPS
70 A
IG Main
30 A
*1
50 A
*2
Fuse Box Main 2
50 A
ABS/VSA Motor
40 A
Fuse Box Main 1
30 A
Fuse Box Main 3
*
40 A
2
Rear Defogger
30 A
EPB L
30 A
IG Main2
*1
*2
30 A
30 A
HTR
40 A
EPB R
30 A
AWD
*
30 A
*1:Models with smart entry system
*2:Models without smart entry system
Circuit Protected
Amps
3
4
5
ABS/VSA FSR
30 A
6
Deicer
*
(10 A)
7
RR ACC SOCKET
*
(20 A)
8
9
Interior Light
7.5 A
10
ACC Socket (Console)
(20 A)
11
12
*1
12
*2
ACC Key Lock
(7.5 A)
13
Heated Door Mirror
*
(10 A)
14
A/C Blower SW
*
(7.5 A)
15
*1
15
*2
Wiper
30 A
* Not available on all models
474
uu
Fuses
u
Inspecting and Changing Fuses
Handling the Unexpected
Inspecting and Changing Fuses
1.
Turn the ignition switch to LOCK
(
0
*1
. Turn
headlights and all accessories off.
2.
Check the fuses on the battery in the
engine compartment.
u
If the fuse is blown, have it replaced by a
dealer.
3.
Remove the fuse box cover.
4.
Inspect the small fuses in the engine
compartment and the vehicle interior.
u
If there is a burned out fuse, remove it
with the fuse puller and replace it with a
new one.
5.
Check the large fuse in the vehicle interior.
u
If the fuse is blown, use a Phillips-head
screwdriver to remove the screw and
replace it with a new one.
*1: Models with the smart entry system have an
ENGINE START/STOP
button instead of an
ignition switch.
1
Inspecting and Changing Fuses
NOTICE
Replacing a fuse with one that has a higher rating
greatly increases the chances of damaging the
electrical system.
Replace fuse with a spare fuse of the same specified
amperage.
Confirm the specified amperage using the charts on
2
Fuse Locations
P. 470
There is a fuse puller in the back of the engine
compartment fuse box cover.
Fuse Box on the Battery
Blown
Fuse Puller
Combined Fuse
Blown Fuse