Ram 1500 - 2018 Fuse Box Diagram

Ram 1500 - 2018 Fuse Box Diagram

A key symbol indicates that the key must be in the
ON/RUN or ACC positions for the outlet to provide
power. The battery symbol indicates that the outlet is
connected to the battery, and can provide power at all
times.
NOTE:
To ensure proper operation, a Mopar knob and
element must be used.
CAUTION!
Do not exceed the maximum power of 160 Watts
(13 Amps) at 12 Volts. If the 160 Watts (13 Amps) power
rating is exceeded, the fuse protecting the system will
need to be replaced.
Power outlets are designed for accessory plugs only.
Do not insert any other object in the power outlets as
this
will
damage
the
outlet
and
blow
the
fuse.
Improper
use
of
the
power
outlet
can
cause
damage not covered by your New Vehicle Limited
Warranty.
The auxiliary power outlets can be found in the following
locations:
Lower left and lower right of the center stack when
equipped with a bench seat.
Power Outlets — Center Stack
1 — Power Outlet
2 — USB Port (Charge Only)
134
GETTING TO KNOW YOUR VEHICLE
When the vehicle is turned off, be sure to unplug any
equipment as to not drain the battery of the vehicle. All
accessories connected to the outlet(s) should be removed or
turned off when the vehicle is not in use to protect the
battery against discharge.
Power Outlet — Rear Center Console Fuse
Power Outlet Fuse Locations
1 — F104 Fuse 20 A Yellow Power Outlet Center Console Bin /
USB Port (Charge Only)
2 — F90–F91 Fuse 20 A Yellow Power Outlet Rear Center Console
3 — F93 Fuse 20 A Yellow Cigar Lighter Instrument Panel
136
GETTING TO KNOW YOUR VEHICLE
FUSES
WARNING!
When replacing a blown fuse, always use an appro-
priate replacement fuse with the same amp rating as
the original fuse. Never replace a fuse with another
fuse of higher amp rating. Never replace a blown
fuse with metal wires or any other material. Do not
place a fuse inside a circuit breaker cavity or vice
versa. Failure to use proper fuses may result in
serious personal injury, fire and/or property damage.
Before replacing a fuse, make sure that the ignition is
off and that all the other services are switched off
and/or disengaged.
If the replaced fuse blows again, contact an autho-
rized dealer.
If a general protection fuse for safety systems (air
bag system, braking system), power unit systems
(engine
system,
transmission
system)
or
steering
system blows, contact an authorized dealer.
Power Distribution Center
The Power Distribution Center is located in the engine
compartment near the battery. This center contains car-
tridge fuses, micro fuses, relays, and circuit breakers. A
description of each fuse and component may be stamped
on the inside cover, otherwise the cavity number of each
fuse is stamped on the inside cover that corresponds to the
following chart.
Cavity
Cartridge Fuse
Micro Fuse
Description
F01
80 Amp Black
Rad Fan Control Module – If Equipped
Power Distribution Center Location
7
IN CASE OF EMERGENCY
461
Cavity
Cartridge Fuse
Micro Fuse
Description
F03
60 Amp Yellow
Rad Fan – If Equipped
F05
40 Amp Green
Compressor for Air Suspension – If
Equipped
F06
40 Amp Green
Antilock Brakes/Electronic Stability Control
Pump
F07
40 Amp Green
Starter Solenoid
F08
20 Amp Blue
(1500 LD/Cummins
Diesel)
Emissions Diesel – If Equipped
F09
40 Amp Green (Spe-
cial Services Vehicle
& Cummins Diesel)
Diesel Fuel Heater – If Equipped
F10
40 Amp Green
Body Controller / Exterior Lighting #2
F10
50 Amp Red
Body Controller / Exterior Lighting #2 – If
Equipped with Stop/Start
F11
30 Amp Pink
Integrated Trailer Brake Module – If
Equipped
F12
40 Amp Green
Body Controller #3 / Power Locks
F13
40 Amp Green
Blower Motor
F14
40 Amp Green
Body Controller #4 / Interior Lighting
F16
30 Amp Pink
Smart Bar – If Equipped
462
IN CASE OF EMERGENCY
Cavity
Cartridge Fuse
Micro Fuse
Description
F19
20 Amp Blue
(1500 LD Diesel)
30 Amp Pink (Cum-
mins Diesel)
SCR – If Equipped
F20
30 Amp Pink
Passenger Door Module
F21
30 Amp Pink
Drive Train Control Module
F22
20 Amp Blue
30 Amp Pink (Cum-
mins Diesel)
Engine Control Module
F23
30 Amp Pink
Body Controller #1 / Interior Lighting
F24
30 Amp Pink
Driver Door Module
F25
30 Amp Pink
Front Wiper
F26
30 Amp Pink
Antilock Brakes / Stability Control Module /
Valves
F28
20 Amp Blue
Trailer Tow Backup Lights – If Equipped
F29
20 Amp Blue
Trailer Tow Parking Lights – If Equipped
F30
30 Amp Pink
Trailer Tow Receptacle
F31
30 Amp Pink
(1500 LD Diesel)
Urea Heater Control – If Equipped
F32
Spare Fuse
F33
20 Amp Blue
Special Services Vehicle Only
7
IN CASE OF EMERGENCY
463
Cavity
Cartridge Fuse
Micro Fuse
Description
F34
30 Amp Pink
Vehicle System Interface Module #2 – If
Equipped
F35
30 Amp Pink
Sunroof – If Equipped
F36
30 Amp Pink
Rear Defroster – If Equipped
F37
30 Amp Pink
Cummins Diesel Fuel Heater #2 – If
Equipped
F38
30 Amp Pink
Power Inverter 115V AC – If Equipped
F39
20 Amp Blue
Power Outlet – Special Services Only
F41
10 Amp Red
Active Grill Shutter – If Equipped
F42
20 Amp Yellow
Horn
F44
10 Amp Red
Diagnostic Port
F46
10 Amp Red
Upfitter – If Equipped
F49
10 Amp Red
Instrument Panel Cluster
(Except Fleet Vehicles)
F50
20 Amp Yellow
Air Suspension Control Module – If
Equipped
F51
10 Amp Red
Ignition Node Module / Keyless Ignition
(Instrument Panel Cluster – Fleet Vehicles
Only)
F52
5 Amp Tan
Battery Sensor
F53
20 Amp Yellow
Trailer Tow – Left Turn/Stop Lights
464
IN CASE OF EMERGENCY
Cavity
Cartridge Fuse
Micro Fuse
Description
F54
20 Amp Yellow
Adjustable Pedals
F56
15 Amp Blue
Additional Diesel Content – If Equipped
F57
20 Amp Yellow
Transmission
F58
20 Amp Yellow
Spare Fuse
F59
10 Amp Red
SCR Relay – If Equipped
F60
15 Amp Blue
Underhood Lamp
F61
10 Amp Red
(1500 LD Diesel &
Cummins Diesel)
PM Sensor – If Equipped
F62
10 Amp Red
Air Conditioning Clutch
F63
20 Amp Yellow
Ignition Coils (Gas), Urea Heater (Cummins
Diesel)
F64
25 Amp Clear
Fuel Injectors / Powertrain
F65
Spare Fuse
F66
10 Amp Red
Sunroof / Passenger Window Switches /
Rain Sensor
F67
10 Amp Red
CD / DVD / Bluetooth Hands-free Module –
If Equipped
F69
15 Amp Blue
Mod SCR 12V (Cummins Diesel) –
If Equipped
F70
30 Amp Green
Fuel Pump Motor
7
IN CASE OF EMERGENCY
465
Cavity
Cartridge Fuse
Micro Fuse
Description
F71
25 Amp Clear
Amplifier
F72
10 Amp Red
PCM – If Equipped
F73
20 Amp Yellow
Fuel Transfer Pump (HD Only) – If
Equipped
F74
20 Amp Yellow
(Gas Engine & 1500
LD Diesel)
Brake Vacuum Pump Gas/Diesel – If
Equipped
F75
10 Amp Red
Coolant Temperature Valve Actuator
F76
10 Amp Red
Antilock Brakes / Electronic Stability Control
F77
10 Amp Red
Drivetrain Control Module/Front Axle
Disconnect Module
F78
10 Amp Red
Engine Control Module / Electric Power
Steering
F79
15 Amp Blue
Clearance Lights
F80
10 Amp Red
Universal Garage Door Opener / Compass
F81
20 Amp Yellow
Trailer Tow Right Turn / Stop Lights
F82
10 Amp Red
Steering Column Control Module /
Cruise Control
F84
15 Amp Blue
Switch Bank / Instrument Cluster
F85
10 Amp Red
Airbag Module
F86
10 Amp Red
Airbag Module
466
IN CASE OF EMERGENCY
Cavity
Cartridge Fuse
Micro Fuse
Description
F87
10 Amp Red
Air Suspension – If Equipped / Trailer Tow
/ Steering Column Control Module
F88
15 Amp Blue
Instrument Panel Cluster
F90/F91
20 Amp Yellow
Power Outlet (Rear Seats) Customer
Selectable
F93
20 Amp Yellow
Cigar Lighter
F94
10 Amp Red
Shifter / Transfer Case Module
F95
10 Amp Red
Rear Camera / Park Assist
F96
10 Amp Red
Rear Seat Heater Switch
F97
25 Amp Clear
Rear Heated Seats & Heated Steering Wheel
– If Equipped
F98
25 Amp Clear
Front Heated Seats – If Equipped
F99
10 Amp Red
Climate Control
F100
10 Amp Red
Upfitters – If Equipped
F101
15 Amp Blue
Electrochromatic Mirror / Smart High Beams
– If Equipped
F104
20 Amp Yellow
Power Outlets (Instrument Panel /
Center Console)
7
IN CASE OF EMERGENCY
467
CAUTION!
When installing the power distribution center cover,
it is important to ensure the cover is properly posi-
tioned and fully latched. Failure to do so may allow
water to get into the power distribution center and
possibly result in an electrical system failure.
When replacing a blown fuse, it is important to use
only a fuse having the correct amperage rating. The
use of a fuse with a rating other than indicated may
result in a dangerous electrical system overload. If a
properly rated fuse continues to blow, it indicates a
problem in the circuit that must be corrected.
JACKING AND TIRE CHANGING
Jacking And Tire Changing 1500 Series Trucks
WARNING!
Do not attempt to change a tire on the side of the
vehicle close to moving traffic. Pull far enough off
the road to avoid the danger of being hit when
operating the jack or changing the wheel.
(Continued)
WARNING!
(Continued)
Being under a jacked-up vehicle is dangerous. The
vehicle could slip off the jack and fall on you. You
could be crushed. Never put any part of your body
under a vehicle that is on a jack. If you need to get
under a raised vehicle, take it to a service center
where it can be raised on a lift.
Never start or run the engine while the vehicle is on
a jack.
The jack is designed to be used as a tool for changing
tires only. The jack should not be used to lift the
vehicle for service purposes. The vehicle should be
jacked on a firm level surface only. Avoid ice or
slippery areas.
NOTE:
If your vehicle is equipped with an air suspension
system, there is a feature which allows the automatic
leveling to be disabled to assist with changing a tire.
If your vehicle is equipped with a touchscreen, this feature
can be activated through the Uconnect system. Refer to
“Uconnect Settings” in “Multimedia” for further informa-
tion.
468
IN CASE OF EMERGENCY
CAUTION!
(Continued)
The rear hub caps on the dual rear wheel has two
pull off notches. Make sure that the hook of the jack
handle driver is located squarely in the cap notch
before attempting to pull off.
You must use the flat end of the lug wrench to pull off the
wheel skins. Locate the hub cap pull notches (2 notches on
each cap). Insert the flat tip completely and using a back
and forth motion, loosen the wheel skin. Repeat this
procedure around the tire until the skin pops off.
Replace the wheel skins first using a rubber mallet. When
replacing the hub caps, tilt the cap retainer over the lug nut
bolt circle and strike the high side down with a rubber
mallet. Be sure that the hub caps and wheel skins are firmly
seated around the wheel.
JUMP STARTING
If your vehicle has a discharged battery, it can be jump
started using a set of jumper cables and a battery in another
vehicle, or by using a portable battery booster pack. Jump
starting can be dangerous if done improperly, so please
follow the procedures in this section carefully.
WARNING!
Do not attempt jump starting if the battery is frozen. It
could rupture or explode and cause personal injury.
CAUTION!
Do not use a portable battery booster pack or any other
booster source with a system voltage greater than
12 Volts or damage to the battery, starter motor, alter-
nator or electrical system may occur.
NOTE:
When using a portable battery booster pack, follow
the manufacturer’s operating instructions and precautions.
Preparations For Jump Start
The battery in your vehicle is located in the front of the
engine compartment, behind the left headlight assembly.
NOTE:
The positive battery post may be covered with a
protective cap if equipped. Lift up on the cap to gain access
to the positive battery post. Do not jump off fuses. Only
jump directly off positive post which has a positive
(+)
symbol on or around the post.
502
IN CASE OF EMERGENCY
Jump Starting Procedure
WARNING!
Failure to follow this jump starting procedure could
result in personal injury or property damage due to
battery explosion.
CAUTION!
Failure to follow these procedures could result in
damage to the charging system of the booster vehicle
or the discharged vehicle.
Connecting The Jumper Cables
1. Connect the positive
(+)
end of the jumper cable to the
positive
(+)
post of the discharged vehicle.
NOTE: Do not jump off fuses. Only jump directly off
positive post.
2. Connect the opposite end of the positive
(+)
jumper
cable to the positive
(+)
post of the booster battery.
3. Connect the negative
(-)
end of the jumper cable to the
negative
(-)
post of the booster battery.
4. Connect the opposite end of the negative
(-)
jumper
cable to a good engine ground (exposed metal part of
the discharged vehicle’s engine) away from the battery
and the fuel injection system.
WARNING!
Do not connect the jumper cable to the negative (-) post
of the discharged battery. The resulting electrical spark
could cause the battery to explode and could result in
personal injury. Only use the specific ground point, do
not use any other exposed metal parts.
5. Start the engine in the vehicle that has the booster
battery, let the engine idle a few minutes, and then start
the engine in the vehicle with the discharged battery.
CAUTION!
Do not connect jumper cable to any of the fuses on the
positive battery terminal. The resulting electrical cur-
rent will blow the fuse.
504
IN CASE OF EMERGENCY
ENGINE COMPARTMENT
3.6L Engine
1 — Air Cleaner Filter
2 — Engine Oil Dipstick
3 — Engine Oil Fill
4 — Brake Fluid Reservoir
5 — Battery
6 — Washer Fluid Reservoir
7 — Power Distribution Center (Fuses)
8 — Coolant Pressure Cap
9 — Engine Coolant Reservoir
8
SERVICING AND MAINTENANCE
523
5.7L Engine
1 — Air Cleaner Filter
7 — Washer Fluid Reservoir
2 — Automatic Transmission Dipstick (6-Speed Trans Only)
8 — Power Distribution Center (Fuses)
3 — Engine Oil Fill
9 — Power Steering Fluid Reservoir (2500/3500 Models Only)
4 — Engine Oil Dipstick
10 — Coolant Pressure Cap
5 — Brake Fluid Reservoir
11 — Engine Coolant Reservoir
6 — Battery
524
SERVICING AND MAINTENANCE
6.4L Engine
1 — Coolant Pressure Bottle
6 — Battery
2 — Transmission Dipstick
7 — Power Distribution Center (Fuses)
3 — Engine Oil Fill
8 — Washer Solvent
4 — Engine Oil Dipstick
9 — Power Steering Fluid Reservoir
5 — Brake Fluid Reservoir
10 — Air Cleaner Filter
8
SERVICING AND MAINTENANCE
525
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.
The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect
the
accuracy
or
operation
of
the
compass
on
vehicles so equipped.
The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
NOTE:
Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
INTERNAL EQUIPMENT
Electrical Power Outlets
The auxiliary 12 Volt (13 Amp) power outlets
can provide power for in-cab accessories de-
signed
for
use
with
the
standard
“cigar
lighter” plug. The 12 Volt power outlets and
USB Port (Charge Only) have a cap attached
to the outlet indicating “12V DC,” together
with either a key symbol, battery symbol, or
USB symbol.
A key symbol indicates that the key must be
in the ON/RUN or ACC positions for the outlet
to provide power. The battery symbol indi-
cates that the outlet is connected to the
battery, and can provide power at all times.
NOTE:
To ensure proper operation, a Mopar knob
and element must be used.
CAUTION!
• Do not exceed the maximum power of
160 Watts (13 Amps) at 12 Volts. If the
160 Watts (13 Amps) power rating is
exceeded, the fuse protecting the sys-
tem will need to be replaced.
• Power outlets are designed for accessory
plugs only. Do not insert any other object
in the power outlets as this will damage
the outlet and blow the fuse. Improper
use of the power outlet can cause dam-
age not covered by your New Vehicle
Limited Warranty.
The auxiliary power outlets can be found in
the following locations:
• Lower left and lower right in the center of
the instrument panel – if equipped with a
column or a eight-speed electronic gear
selector.
• Inside the top storage tray.
Power Outlet — Center Console
55
Bulb Number
Premium Backup
Lamp
7440/W21W
Rear Lamp Bar ID
Marker Lamp
194
Side Marker Lamps
(Dual Rear Wheels)
194
Backup Lamp
921
Rear License Plate
Lamp
194
FUSES
WARNING!
• When replacing a blown fuse, always use
an appropriate replacement fuse with
the same amp rating as the original fuse.
Never replace a fuse with another fuse of
WARNING!
higher
amp
rating.
Never
replace
a
blown fuse with metal wires or any other
material. Do not place a fuse inside a
circuit breaker cavity or vice versa. Fail-
ure to use proper fuses may result in
serious personal injury, fire and/or prop-
erty damage.
• Before replacing a fuse, make sure that
the ignition is off and that all the other
services are switched off and/or disen-
gaged.
• If the replaced fuse blows again, contact
an authorized dealer.
• If a general protection fuse for safety
systems (air bag system, braking sys-
tem), power unit systems (engine sys-
tem, transmission system) or steering
WARNING!
system
blows,
contact
an
authorized
dealer.
Power Distribution Center
The Power Distribution Center is located in
the engine compartment near the battery.
This center contains cartridge fuses, micro
fuses, relays, and circuit breakers. A descrip-
tion of each fuse and component may be
stamped on the inside cover, otherwise the
cavity number of each fuse is stamped on the
inside cover that corresponds to the following
chart.
Cavity
Cartridge Fuse
Micro Fuse
Description
F01
80 Amp Black
Rad Fan Control Module – If Equipped
F03
60 Amp Yellow
Rad Fan – If Equipped
F05
40 Amp Green
Compressor for Air Suspension – If Equipped
F06
40 Amp Green
Antilock Brakes/Electronic Stability Control Pump
203
Cavity
Cartridge Fuse
Micro Fuse
Description
F07
40 Amp Green
Starter Solenoid
F08
20 Amp Blue (1500 LD/
Cummins Diesel)
Emissions Diesel – If Equipped
F09
40 Amp Green (Special
Services Vehicle & Cum-
mins Diesel)
Diesel Fuel Heater – If Equipped
F10
40 Amp Green
Body Controller / Exterior Lighting #2
F10
50 Amp Red
Body Controller / Exterior Lighting #2 – If Equipped with
Stop/Start
F11
30 Amp Pink
Integrated Trailer Brake Module – If Equipped
F12
40 Amp Green
Body Controller #3 / Power Locks
F13
40 Amp Green
Blower Motor
F14
40 Amp Green
Body Controller #4 / Interior Lighting
F16
30 Amp Pink
Smart Bar – If Equipped
F19
20 Amp Blue (1500 LD
Diesel)
30 Amp Pink (Cummins
Diesel)
SCR – If Equipped
F20
30 Amp Pink
Passenger Door Module
F21
30 Amp Pink
Drive Train Control Module
F22
20 Amp Blue
30 Amp Pink (Cummins
Diesel)
Engine Control Module
F23
30 Amp Pink
Body Controller #1 / Interior Lighting
F24
30 Amp Pink
Driver Door Module
IN CASE OF EMERGENCY
204
Cavity
Cartridge Fuse
Micro Fuse
Description
F25
30 Amp Pink
Front Wiper
F26
30 Amp Pink
Antilock Brakes / Stability Control Module / Valves
F28
20 Amp Blue
Trailer Tow Backup Lights – If Equipped
F29
20 Amp Blue
Trailer Tow Parking Lights – If Equipped
F30
30 Amp Pink
Trailer Tow Receptacle
F31
30 Amp Pink (1500 LD
Diesel)
Urea Heater Control – If Equipped
F32
Spare Fuse
F33
20 Amp Blue
Special Services Vehicle Only
F34
30 Amp Pink
Vehicle System Interface Module #2 – If Equipped
F35
30 Amp Pink
Sunroof – If Equipped
F36
30 Amp Pink
Rear Defroster – If Equipped
F37
30 Amp Pink
Cummins Diesel Fuel Heater #2 – If Equipped
F38
30 Amp Pink
Power Inverter 115V AC – If Equipped
F39
20 Amp Blue
Power Outlet – Special Services Only
F41
10 Amp Red
Active Grill Shutter – If Equipped
F42
20 Amp Yellow
Horn
F44
10 Amp Red
Diagnostic Port
F46
10 Amp Red
Upfitter – If Equipped
F49
10 Amp Red
Instrument Panel Cluster (Except Fleet Vehicles)
F50
20 Amp Yellow
Air Suspension Control Module – If Equipped
F51
10 Amp Red
Ignition Node Module / Keyless Ignition (Instrument
Panel Cluster – Fleet Vehicles Only)
205
Cavity
Cartridge Fuse
Micro Fuse
Description
F52
5 Amp Tan
Battery Sensor
F53
20 Amp Yellow
Trailer Tow – Left Turn/Stop Lights
F54
20 Amp Yellow
Adjustable Pedals
F56
15 Amp Blue
Additional Diesel Content – If Equipped
F57
20 Amp Yellow
Transmission
F58
20 Amp Yellow
Spare Fuse
F59
10 Amp Red
SCR Relay – If Equipped
F60
15 Amp Blue
Underhood Lamp
F61
10 Amp Red (1500 LD Die-
sel & Cummins Diesel)
PM Sensor – If Equipped
F62
10 Amp Red
Air Conditioning Clutch
F63
20 Amp Yellow
Ignition Coils (Gas), Urea Heater (Cummins Diesel)
F64
25 Amp Clear
Fuel Injectors / Powertrain
F65
Spare Fuse
F66
10 Amp Red
Sunroof / Passenger Window Switches / Rain Sensor
F67
10 Amp Red
CD / DVD / Bluetooth Hands-free Module – If Equipped
F69
15 Amp Blue
Mod SCR 12V (Cummins Diesel) – If Equipped
F70
30 Amp Green
Fuel Pump Motor
F71
25 Amp Clear
Amplifier
F72
10 Amp Red
PCM – If Equipped
F73
20 Amp Yellow
Fuel Transfer Pump (HD Only) – If Equipped
F74
20 Amp Yellow (Gas Engine
& 1500 LD Diesel)
Brake Vacuum Pump Gas/Diesel – If Equipped
IN CASE OF EMERGENCY
206
Cavity
Cartridge Fuse
Micro Fuse
Description
F75
10 Amp Red
Coolant Temperature Valve Actuator
F76
10 Amp Red
Antilock Brakes / Electronic Stability Control
F77
10 Amp Red
Drivetrain Control Module/Front Axle Disconnect Module
F78
10 Amp Red
Engine Control Module / Electric Power Steering
F79
15 Amp Blue
Clearance Lights
F80
10 Amp Red
Universal Garage Door Opener / Compass
F81
20 Amp Yellow
Trailer Tow Right Turn / Stop Lights
F82
10 Amp Red
Steering Column Control Module / Cruise Control
F84
15 Amp Blue
Switch Bank / Instrument Cluster
F85
10 Amp Red
Airbag Module
F86
10 Amp Red
Airbag Module
F87
10 Amp Red
Air Suspension – If Equipped / Trailer Tow / Steering Col-
umn Control Module
F88
15 Amp Blue
Instrument Panel Cluster
F90/F91
20 Amp Yellow
Power Outlet (Rear Seats) Customer Selectable
F93
20 Amp Yellow
Cigar Lighter
F94
10 Amp Red
Shifter / Transfer Case Module
F95
10 Amp Red
Rear Camera / Park Assist
F96
10 Amp Red
Rear Seat Heater Switch
F97
25 Amp Clear
Rear Heated Seats & Heated Steering Wheel – If
Equipped
F98
25 Amp Clear
Front Heated Seats – If Equipped
F99
10 Amp Red
Climate Control
207
Cavity
Cartridge Fuse
Micro Fuse
Description
F100
10 Amp Red
Upfitters – If Equipped
F101
15 Amp Blue
Electrochromatic Mirror / Smart High Beams – If
Equipped
F104
20 Amp Yellow
Power Outlets (Instrument Panel / Center Console)
CAUTION!
• When installing the power distribution
center cover, it is important to ensure
the cover is properly positioned and fully
latched. Failure to do so may allow water
to get into the power distribution center
and possibly result in an electrical sys-
tem failure.
• When replacing a blown fuse, it is impor-
tant to use only a fuse having the correct
amperage rating. The use of a fuse with
a rating other than indicated may result
in a dangerous electrical system over-
load. If a properly rated fuse continues
to blow, it indicates a problem in the
circuit that must be corrected.
JACKING AND TIRE CHANGING
Jack Location
The jack and jack tools are stored under the
front passenger seat.
Removal Of Jack And Tools
• To access the jack and jack tools you must
remove the plastic access cover, located on
the side of the seat. To remove the cover,
pull the front part of the cover (closest to
the front of the seat) toward you to release a
locking tab. Once the front of the cover is
loose, slide the cover toward the front of the
seat until it is free from the seat frame.
Jack And Tools Location
IN CASE OF EMERGENCY
208
NOTE:
The positive battery post may be covered with
a protective cap if equipped. Lift up on the
cap to gain access to the positive battery
post. Do not jump off fuses. Only jump di-
rectly off positive post which has a positive
(+)
symbol on or around the post.
WARNING!
• Take care to avoid the radiator cooling
fan whenever the hood is raised. It can
start anytime the ignition switch is ON.
You can be injured by moving fan blades.
• Remove any metal jewelry such as rings,
watch bands and bracelets that could
make an inadvertent electrical contact.
You could be seriously injured.
• Batteries contain sulfuric acid that can
burn your skin or eyes and generate
hydrogen gas which is flammable and
explosive. Keep open flames or sparks
away from the battery.
1. Apply the parking brake, shift the auto-
matic transmission into PARK and turn
the ignition to LOCK.
2. Turn off the heater, radio, and all unnec-
essary electrical accessories.
3. If using another vehicle to jump start the
battery, park the vehicle within the jumper
cables reach, apply the parking brake and
make sure the ignition is OFF.
WARNING!
Do not allow vehicles to touch each other
as this could establish a ground connec-
tion and personal injury could result.
Jump Starting Procedure
WARNING!
Failure to follow this jump starting proce-
dure could result in personal injury or
property damage due to battery explosion.
CAUTION!
Failure to follow these procedures could
result in damage to the charging system of
the booster vehicle or the discharged ve-
hicle.
Connecting The Jumper Cables
1. Connect the positive
(+)
end of the jumper
cable to the positive
(+)
post of the dis-
charged vehicle.
NOTE:
Do not jump off fuses. Only jump directly off
positive post.
2. Connect the opposite end of the positive
(+)
jumper cable to the positive
(+)
post of
the booster battery.
3. Connect the negative
(-)
end of the jumper
cable
to
the
negative
(-)
post
of
the
booster battery.
4. Connect the opposite end of the negative
(-)
jumper cable to a good engine ground
(exposed metal part of the discharged
vehicle’s engine) away from the battery
and the fuel injection system.
WARNING!
Do not connect the jumper cable to the
negative (-) post of the discharged battery.
The resulting electrical spark could cause
the battery to explode and could result in
219
WARNING!
personal
injury.
Only
use
the
specific
ground point, do not use any other exposed
metal parts.
5. Start the engine in the vehicle that has
the booster battery, let the engine idle a
few minutes, and then start the engine in
the vehicle with the discharged battery.
CAUTION!
Do not connect jumper cable to any of the
fuses on the positive battery terminal. The
resulting electrical current will blow the
fuse.
6. Once the engine is started, remove the
jumper cables in the reverse sequence:
Disconnecting The Jumper Cables
1. Disconnect the negative
(-)
end of the
jumper cable from the engine ground of
the vehicle with the discharged battery.
2. Disconnect the opposite end of the nega-
tive
(-)
jumper cable from the negative
(-)
post of the booster battery.
3. Disconnect the positive
(+)
end of the
jumper cable from the positive
(+)
post of
the booster battery.
4. Disconnect the opposite end of the posi-
tive
(+)
jumper cable from the positive
(+)
post of the vehicle with the discharged
battery.
If frequent jump starting is required to start
your vehicle you should have the battery and
charging system inspected at an authorized
dealer.
CAUTION!
Accessories
plugged
into
the
vehicle
power outlets draw power from the vehi-
cle’s battery, even when not in use (i.e.,
cellular
devices,
etc.).
Eventually,
if
plugged in long enough without engine
operation, the vehicle’s battery will dis-
charge sufficiently to degrade battery life
and/or prevent the engine from starting.
IF YOUR ENGINE OVERHEATS
In any of the following situations, you can
reduce the potential for overheating by taking
the appropriate action.
• On the highways — slow down.
• In city traffic — while stopped, place the
transmission in NEUTRAL, but do not in-
crease the engine idle speed while prevent-
ing vehicle motion with the brakes.
NOTE:
There are steps that you can take to slow
down an impending overheat condition:
• If your air conditioner (A/C) is on, turn it off.
The A/C system adds heat to the engine
cooling system and turning the A/C off can
help remove this heat.
• You can also turn the temperature control
to maximum heat, the mode control to floor
and the blower control to high. This allows
the heater core to act as a supplement to
the radiator and aids in removing heat from
the engine cooling system.
IN CASE OF EMERGENCY
220
ENGINE COMPARTMENT
3.6L Engine
1 — Air Cleaner Filter
2 — Engine Oil Dipstick
3 — Engine Oil Fill
4 — Brake Fluid Reservoir
5 — Battery
6 — Power Distribution Center (Fuses)
7 — Washer Fluid Reservoir
8 — Coolant Pressure Cap
9 — Engine Coolant Reservoir
243
5.7L Engine
1 — Air Cleaner Filter
6— Battery
2 — Automatic Transmission Dipstick (6-Speed Trans Only)
7 — Power Distribution Center (Fuses)
3 — Engine Oil Fill
8 — Washer Fluid Reservoir
4 — Engine Oil Dipstick
9 — Coolant Pressure Cap
5 — Brake Fluid Reservoir
10 — Engine Coolant Reservoir
SERVICING AND MAINTENANCE
244
6.4L Engine
1 — Coolant Pressure Bottle
7 — Battery
2 — Transmission Dipstick
8 — Power Distribution Center (Fuses)
3 — Engine Oil Fill
9 — Washer Fluid Reservoir
4 — Engine Oil Dipstick
10 — Power Steering Fluid Reservoir
5 — Brake Fluid Reservoir
11 — Air Cleaner Filter
6 — Aux Power Distribution Center (Fuses)
245
3.0L Diesel Engine
1 — Air Cleaner Filter
6 — Power Distribution Center (PDC)
2 — Engine Oil Fill
7 — Washer Fluid Reservoir
3 — Brake Fluid Reservoir
8 — Engine Coolant Reservoir
4 — Aux Power Distribution Center (Fuses)
9 — Engine Oil Dipstick
5 — Battery
SERVICING AND MAINTENANCE
246