Nissan Qashqai - 2017 Fuse Box Diagram

Nissan Qashqai - 2017 Fuse Box Diagram

JVC1090X
1.
Side ventilator (P.4-29)
2.
Meters and gauges (P.2-5)/Clock (P.2-36)
3.
Center ventilator (P.4-29)
4.
Audio system* (P.4-38) or Navigation system**
— RearView Monitor* (P.4-8)
— Around View
¡
Monitor* (P.4-14)
— Bluetooth
¡
Hands-Free Phone System*
(P.4-82, P.4-92)
5.
Front passenger supplemental air bag (P.1-39)
6.
Fuse box cover (P.8-20)
7.
Fuel-filler door release handle (P.3-27)
8.
Hood release handle (P.3-24)
9.
Steering wheel lock lever (P.3-29)
10.
Driver’s front-impact air bag (P.1-39)/Horn
(P.2-49)
11.
Heater/air conditioner control (P.4-30)
12.
Auxiliary input jack (P.4-62) and USB connec-
tion port (P.4-59, P.4-67)
13.
Power outlet (P.2-53)
14.
Defroster switch (P.2-42)
15.
Glove box (P.2-56)
*:
if so equipped
**:
See the separate Navigation System Owner’s
Manual (if so equipped).
Illustrated table of contents
0-7
INSTRUMENT PANEL
JVC1070X
MR20DD ENGINE MODEL
1.
Engine coolant reservoir (P.8-5)
2.
Engine oil filler cap (P.8-6)
3.
Brake and clutch* fluid reservoir (P.8-9)
4.
Air cleaner (P.8-14)
5.
Window washer fluid reservoir (P.8-10)
6.
Drive belt (P.8-13)
7.
Engine oil dipstick (P.8-6)
8.
Battery (P.8-11)
9.
Fuse/fusible link box (P.8-18)
*:
For Manual Transmission (MT) Model
Illustrated table of contents
0-9
ENGINE COMPARTMENT
2-4
Instruments and controls
JVC1090X
1.
Side ventilator
2.
Meters and gauges/Clock
3.
Center ventilator
4.
Audio system* or Navigation system**
— RearView Monitor*
— Around View
¡
Monitor*
— Bluetooth
¡
Hands-Free Phone System*
5.
Front passenger supplemental air bag
6.
Fuse box cover
7.
Fuel-filler door release handle
8.
Hood release handle
9.
Steering wheel lock lever
10.
Driver’s front-impact air bag/Horn
11.
Heater/air conditioner control
12.
Auxiliary input jack and USB connection port
13.
Power outlet
14.
Defroster switch
15.
Glove box
*:
if so equipped
**:
See the separate Navigation System Owner’s
Manual (if so equipped).
INSTRUMENT PANEL
2-14
Instruments and controls
TPMS will not function and the low
tire pressure warning light will flash
for
approximately
1
minute.
The
light will remain on after 1 minute.
Have
your
tires
replaced
and/or
TPMS
system
reset
as
soon
as
possible.
It
is
recommended
you
visit
a
NISSAN
dealer
for
these
services.
.
Replacing tires with those not ori-
ginally specified by NISSAN could
affect the proper operation of the
TPMS.
CAUTION
.
The TPMS is not a substitute for the
regular tire pressure check. Be sure
to check the tire pressure regularly.
.
If
the
vehicle
is
being
driven
at
speeds
of less than 16
MPH (25
km/h), the TPMS may not operate
correctly.
.
Be sure to install the specified size
of tires to the four wheels correctly.
Master warning light
When the ignition switch is in the ON position,
the master warning light illuminates if any of the
following are displayed on the vehicle informa-
tion display.
.
No Key detected warning (if so equipped)
.
Shift to Park warning (Continuously Variable
Transmission
(CVT)
models)
(if
so
equipped)
.
Key battery low warning (if so equipped)
.
Engine start operation for Intelligent Key
system indicator (if so equipped)
.
Key ID incorrect warning (if so equipped)
.
Release Parking Brake warning
.
Low fuel level warning
.
Low Washer Fluid (if so equipped)
.
Door/liftgate open warning
.
Key
System
Error:
See
Owner’s
Manual
warning (if so equipped)
.
Loose Fuel Cap
.
Tire Pressure Low - Add Air warning
.
Low oil pressure Stop vehicle warning
.
AWD Error: See Owner’s Manual warning (if
so equipped)
.
AWD High Temp. Stop vehicle warning (if so
equipped)
.
Tire Size Incorrect: See Owner’s Manual
warning (if so equipped)
.
Battery Voltage Low Charge Battery warn-
ing
.
Shipping
Mode
On
Push
Storage
Fuse
warning
.
Power
will
turn
off
to
save
the
battery
warning
.
Power turned off to save the battery warning
.
Reminder: Turn OFF Headlights warning
.
Headlight System Error: See Owner’s Man-
ual warning (if so equipped)
.
Timer
Alert
- Time
for
a
driver
break?
indicator (if so equipped)
.
Chassis Control System Error: See Owner’s
Manual warning
.
CVT Error: See Owner’s Manual warning
(for
Continuously
Variable
Transmission
(CVT) models)
.
Malfunction warning (if so equipped)
.
Unavailable: High Cabin Temperature warn-
ing (if so equipped)
.
Not Available: Poor Road Conditions warn-
ing (if so equipped)
.
Currently
unavailable
warning
(if
so
equipped)
.
Unavailable: Front Radar Obstruction warn-
ing (if so equipped)
2-30
Instruments and controls
18. Tire Size Incorrect: See Owner’s
Manual warning (if so equipped)
This warning may appear if there is a large
difference between the diameters of the front
and rear wheels and tires. Pull off the road in a
safe area, with the engine idling. Check that all
the tire sizes are the same, that the tire pressure
is correct and that the tires are not excessively
worn. See “All-Wheel Drive (AWD)” (P.5-96).
19. Battery Voltage Low Charge Battery
warning
This warning appears when the battery voltage
is low and the battery needs to be charged.
20. Shipping Mode On Push Storage
Fuse warning
This warning may appear if the extended storage
fuse switch is not pushed in (switched on).
When this warning appears, push in (switch on)
the extended storage fuse switch to turn off the
warning. For more information, see “Extended
storage fuse switch” (P.8-21).
21. Power will turn off to save the battery
warning
This warning appears after the ignition switch is
in the ON position for a certain period of time.
22. Power turned off to save the battery
warning
This warning appears after the ignition switch is
automatically turned OFF to save the battery.
23. Reminder: Turn OFF Headlights
warning
This warning appears when the driver side door
is opened with the headlight switch is left ON
and the ignition switch is placed in the OFF or
LOCK position. Place the headlight switch in
OFF or AUTO (if so equipped) position. For
additional information, see “Headlight and turn
signal switch” (P.2-43).
24. Headlight System Error: See Own-
er’s Manual warning (if so equipped)
This warning appears if the LED headlights are
malfunctioning. Have the system checked. It is
recommended that you visit a NISSAN dealer for
this service.
25. Timer Alert — Time for a driver
break? indicator
This indicator appears when the set “Time for a
driver break?” indicator activates. You can set
the time for up to 6 hours.
26. Chassis Control System Error: See
Owner’s Manual warning
This
warning
appears
if
the
chassis
control
module detects an error in the chassis control
system. Have the system checked. It is recom-
mended that you visit a NISSAN dealer for this
service. (See “Chassis control” (P.5-106).)
27. Cruise control indicator (if so
equipped)
This indicator shows the cruise control system
status. The status is shown by the color.
See “Cruise control” (P.5-58) for details.
28. Intelligent Cruise Control (ICC)
indicator (if so equipped)
This
indicator
shows
the
Intelligent
Cruise
Control
(ICC)
system
status.
The
status
is
shown by the color. (See “Intelligent Cruise
Control (ICC)” (P.5-60).)
.
The ECO mode system will turn off auto-
matically
if
a
malfunction
occurs
in
the
system.
.
Turn
off
the
ECO
mode
system
when
acceleration is required such as when:
— driving with a heavy load of passengers
or cargo in the vehicle
— driving on a steep uphill slope
JVI0878X
The power outlet is located in the instrument
panel.
CAUTION
.
The
outlet
and
plug
may
be
hot
during or immediately after use.
.
Do not use with accessories that
exceed a 12 volt, 120W (10A) power
draw. Do not use double adapters or
more than one electrical accessory.
.
Use power outlet with the engine
running
to
avoid
discharging
the
vehicle battery.
.
Avoid using power outlet when the
air conditioner, headlights or rear
window defroster is on.
.
This power outlet is not designed
for use with a cigarette lighter unit.
.
Push the plug in as far as it will go.
If good contact is not made, the plug
may overheat or the internal tem-
perature fuse may open.
.
Before inserting or disconnecting a
plug, be sure the electrical acces-
sory being used is turned OFF.
.
When not in use, be sure to close
the cap. Do not allow water or any
liquid to contact the outlet.
Instruments and controls
2-53
POWER OUTLET
4-50
Heater, air conditioner, audio and phone systems
SETTING/TUNE·FOLDER
dial
and
then
push the ENTER SETTING/TUNE·FOLDER
dial.
Use
the
ENTER
SETTING/
TUNE·FOLDER dial to select the preferred
language.
Push
the
ENTER
SETTING/
TUNE·FOLDER dial to apply the setting.
DISP button:
Display
of
the
screen
can
be
canceled
by
pushing the
button. You can still listen to
music that is being played back even while the
screen display is turned off. If you want to
display the screen again, push the
button
once more. Pushing some of the audio source
buttons will also turn the screen back on and
display
the
screens
of
the
corresponding
sources.
MEDIA button:
Pushing the
button will switch the audio
source as follows:
USB/iPod
?
Bluetooth Audio
?
AUX
?
USB/
iPod
FM-AM Radio operation
radio (FM·AM) band select:
Push the
button to change the band as
follows:
AM
?
FM1
?
FM2
?
AM
The FM stereo indicator (STEREO) is shown on
the screen during FM stereo reception. When
the stereo broadcast signal is weak, the radio
automatically changes from stereo to monaural
reception.
TUNE (Tuning):
Turn the ENTER SETTING/TUNE·FOLDER dial
for manual tuning.
Radio Data System (RDS):
RDS stands for Radio Data System, and is a
data information service transmitted by some
radio stations on the FM band (not AM band)
encoded
within
a
regular
radio
broadcast.
Currently, most RDS stations are in large cities,
but many stations are now considering broad-
casting RDS data.
The station name, such as “The Groove”, is
displayed on the display.
SEEK tuning:
Push the
or
button to tune from low to
high or high to low frequencies and to stop at
the next broadcasting station.
SCAN tuning:
Push the
button to tune from low to high
frequencies
and
stop
at
each
broadcasting
station for several seconds. Pushing the
button again during this several seconds period
will stop SCAN tuning and the radio will remain
tuned to that station.
If the
button is not pushed within this
period, SCAN tuning moves to the next station.
to
Station memory operations:
Up to 12 stations can be set for the FM band (6
each for FM1 and FM2) and 6 stations can be
set for the AM band.
1.
Choose
the
radio
band
using
the
button.
2.
Tune to the desired station.
3.
Push and hold the desired station preset
button
to
until beep sounds.
4.
The station indicator will then come on. The
station is now set to the button memory.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the station memory will be erased. In that
4-58
Heater, air conditioner, audio and phone systems
categories when any category is not se-
lected.
Radio Data System (RDS):
RDS stands for Radio Data System, and is a
data information service transmitted by some
radio stations on the FM band (not AM band)
encoded
within
a
regular
radio
broadcast.
Currently, most RDS stations are in large cities,
but many stations are now considering broad-
casting RDS data.
The station name, such as “The Groove”, is
displayed on the display.
SEEK tuning/CAT (category):
.
For AM and FM radio
Push the
or
button to tune from low
to high or high to low frequencies and to
stop at the next broadcasting station.
.
For SiriusXM Satellite Radio
Push the
or
button to tune to the
first channel of the next or previous category.
SCAN tuning:
Push the
button to tune from low to high
frequencies
and
stop
at
each
broadcasting
station for several seconds. Pushing the
button again during this several seconds period
will stop SCAN tuning and the radio will remain
tuned to that station.
If the
button is not pushed within five
seconds,
SCAN
tuning
moves
to
the
next
station.
to
Station memory operations:
6 stations can be set for the AM band. 12
stations can be set for the FM band (6 for FM1,
6 for FM2). 18 channels can be set for the
satellite radio (6 for XM1, 6 for XM2, 6 for XM3).
1.
Choose the radio band using the
or XM
button.
2.
Tune to the desired station or channel.
3.
Push and hold the desired station or channel
preset button
to
until beep sounds.
4.
The station or channel indicator will then
come on. Memorizing is now complete.
5.
Other
buttons
can
be
set
in
the
same
manner.
If the battery cable is disconnected, or if the fuse
opens, the station memory will be erased. In that
case, reset the desired stations or channels.
CD player operation
Place the ignition switch in the ACC or ON
position, and insert the Compact Disc (CD) into
the slot with the label side facing up. The CD will
be guided automatically into the slot and start
playing.
After loading the CD, the number of tracks on
the CD and the play time will appear on the
display.
If another audio source is already operating, it
will automatically turn off and the CD will play.
If the system was turned off while the CD was
playing, pushing the Power/VOL dial will start
the CD.
PLAY:
With a CD loaded, push the
button until the
CD mode is displayed on the screen.
CD/MP3 display mode:
While listening to an MP3/WMA CD, certain text
may be displayed on the screen if the CD has
been encoded with text information. Depending
on
how
the
MP3/WMA
CD
is
encoded,
information such as Artist, Song and Folder will
be displayed. The track number and the total
number of tracks in the current folder or on the
current disc are displayed on the screen as well.
station or channel indicator will then come
on.
3.
Other keys can be set in the same manner.
If the battery cable is disconnected or if the fuse
opens, the radio memory will be erased. In that
case, reset the desired stations or channels.
JVH1618X
Smart Favorites preset setup (if so
equipped):
The Smart Favorites feature allows the user to
designate presets, within the SXM1, SXM2 and
SXM3 bands, as their Smart Favorites. When
any of the Smart Favorite presets are selected,
the current track on that channel will play from
the beginning of the song.
To program a Smart Favorite preset:
1.
Push the SXM button.
2.
Touch the “Setup” key.
3.
Touch the “Tune Start” key to activate (ON)
or deactivate (OFF) Smart Favorites.
4.
Touch the “Add Preset” key to select an
available preset.
For additional information, refer to “1 to 6 station
or channel memory operations” (P.4-64) in this
section regarding preset memory operations.
NOTE:
.
Smart Favorites will start functioning
only after the audio unit is turned on
for a few minutes.
.
Tune
Start
is
supported
for
music
channels only.
Replay screen
Heater, air conditioner, audio and phone systems
4-65
8-4
Do-it-yourself
JVC1070X
MR20DD ENGINE MODEL
1.
Engine coolant reservoir
2.
Engine oil filler cap
3.
Brake and clutch* fluid reservoir
4.
Air cleaner
5.
Window washer fluid reservoir
6.
Drive belt
7.
Engine oil dipstick
8.
Battery
9.
Fuse/fusible link box
*:
For Manual Transmission (MT) Model
The engine cooling system is filled at the factory
with
a
pre-diluted
mixture
of
50%
Genuine
NISSAN Long Life Antifreeze/Coolant (blue) and
50% water to provide year-round anti-freeze
and coolant protection. The anti-freeze solution
contains rust and corrosion inhibitors. Additional
engine cooling system additives are not neces-
sary.
WARNING
.
Never remove the radiator or cool-
ant reservoir cap when the engine is
hot.
Wait
until
the
engine
and
radiator cool down. Serious burns
could be caused by high pressure
fluid
escaping
from
the
radiator.
See precautions in
If your vehicle
overheats
(P.6-11) of this manual.
.
The
radiator
is
equipped
with
a
pressure type radiator cap. To pre-
vent
engine
damage,
use
only
a
genuine NISSAN radiator cap.
.
If
the
engine
was
stopped
soon
when the engine is hot, the cooling
fan may operate for approximately
10
minutes
after
the
engine
was
stopped to cool the components in
the engine compartment. When the
ENGINE COOLING SYSTEM
8-18
Do-it-yourself
JVM0386X
ENGINE COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch and the headlight
switch are turned off.
2.
Open the engine hood.
3.
Remove the fuse/fusible link box cover by
using a suitable tool and pushing the tab.
4.
Locate the fuse that needs to be replaced.
5.
Remove
the
fuse
using
the
fuse
puller
located in the passenger compartment fuse
box.
SDI1753
Type A
SDI1754
Type B
FUSES
6.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
.
7.
If a new fuse also opens, have the electrical
system checked and repaired. It is recom-
mended you visit a NISSAN dealer for this
service.
JVM0444X
The holder
*
1
also contains the fuses. It is
recommended you visit a NISSAN dealer for
checking and/or replacing.
Fusible links
If any electrical equipment does not operate and
the
fuses are
in good
condition,
check the
fusible links. If any of these fusible links are
melted,
replace
only
with
genuine
NISSAN
parts.
For checking and replacing the fusible links, it is
recommended you visit a NISSAN dealer.
Do-it-yourself
8-19
8-20
Do-it-yourself
JVM0387X
PASSENGER COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1.
Be sure the ignition switch and the headlight
switch are turned off.
2.
Remove the fuse box cover.
3.
Remove the fuse with the fuse puller
*
A
.
SDI1754
4.
If the fuse is open
*
A
, replace it with a new
fuse
*
B
.
5.
If a new fuse also opens, have the electrical
system checked and repaired. It is recom-
mended you visit a NISSAN dealer for this
service.
JVM0415X
Extended storage fuse switch (if so
equipped)
To reduce battery drain, the extended storage
fuse switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If
the
extended
storage
fuse
switch
is
not
pushed in (switched on), the meter may display
a warning message. See “20. Shipping Mode
On Push Storage Fuse warning” (P.2-30).
If any electrical equipment does not operate,
remove the extended storage fuse switch and
check for an open fuse.
NOTE:
If the extended storage fuse switch mal-
functions or if the fuse is open, it is not
necessary to replace the switch. In this
case, remove the extended storage fuse
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
1.
To remove the extended storage fuse switch,
be sure the ignition switch is in the OFF or
LOCK position.
2.
Be sure the headlight switch is in the OFF
position.
3.
Remove the fuse box cover.
4.
Pinch the locking tabs
*
1
found on each
side of the extended storage fuse switch.
5.
Pull
the
extended
storage
fuse
switch
straight out from the fuse box
*
2
.
CAUTION
.
Be careful not to allow children to
swallow the battery and removed
parts.
.
An improperly disposed battery can
harm the environment. Always con-
firm
local
regulations
for
battery
disposal.
.
When changing batteries, do not let
dust or oil get on the components.
.
There is danger of explosion if the
lithium
battery
is
incorrectly
re-
placed. Replace only with the same
or equivalent type.
Do-it-yourself
8-21
KEY FOB BATTERY REPLACEMENT