Nissan Z Coupe - 2018 Fuse Box Diagram

Nissan Z Coupe - 2018 Fuse Box Diagram

SSI0653
1.
Ventilator (P.4-24)
2.
Center display and multi-function control
panel (if so equipped) (P.4-4) or Instru-
ment pocket (if so equipped) (P.2-43)
— Navigation system* (if so equipped)
— Vehicle information and setting but-
tons (if so equipped) (P.4-8)
— Bluetooth® Hands-Free Phone System
(if so equipped) (P.4-76, P.4-86)
3.
Front passenger air bag status light
(P.1-36)
4.
Front passenger supplemental air bag
(P.1-30)
5.
Fuse box cover (P.8-18)
6.
Push-button ignition switch (P.5-8)
7.
Hazard warning flasher switch (P.6-2)
8.
Seat heater switch (if so equipped)
(P.2-38) or Climate controlled seat switch
(if so equipped) (P.2-40)
9.
Soft top operating switch (for Roadster
models)
(P.3-23)
or
Rear
hatch
release
switch (for Coupe models) (P.3-19)
10.
SynchroRev Match mode (S-MODE) switch
(if so equipped) (P.5-18)
11.
Heater and air conditioner (P.4-25)
— Rear window defroster switch (P.2-33)
12.
Audio system (P.4-30)
13.
Power outlet (P.2-42)
14.
Glove box (P.2-44)
*: Refer to the separate Navigation Sys-
tem Owner’s Manual.
Illustrated table of contents
0-11
INSTRUMENT PANEL
JVC0785X
VQ37VHR ENGINE MODEL
1.
Fuse/fusible link holder (P.8-18)
2.
Battery (P.8-11)
3.
Radiator filler cap (P.8-4)
4.
Engine oil dipstick (P.8-6)
5.
Engine oil filler cap (P.8-6)
6.
Brake fluid reservoir (P.8-9)
7.
Clutch fluid reservoir (Manual Transmis-
sion models) (P.8-9)
8.
Power steering fluid reservoir (P.8-8)
9.
Window washer fluid reservoir (P.8-10)
10.
Air cleaner (P.8-15)
11.
Drive belt location (P.8-14)
12.
Engine coolant reservoir (P.8-4)
13.
Fuse/fusible link holder (P.8-18)
Illustrated table of contents
0-13
ENGINE COMPARTMENT
2-4
Instruments and controls
SSI0653
1.
Ventilator (P.4-24)
2.
Center display and multi-function control
panel (if so equipped) (P.4-4) or Instru-
ment pocket (if so equipped) (P.2-43)
— Navigation system* (if so equipped)
— Vehicle information and setting but-
tons (if so equipped) (P.4-8)
— Bluetooth® Hands-Free Phone System
(if so equipped) (P.4-76, P.4-86)
3.
Front passenger air bag status light
(P.1-36)
4.
Front passenger supplemental air bag
(P.1-30)
5.
Fuse box cover (P.8-18)
6.
Push-button ignition switch (P.5-8)
7.
Hazard warning flasher switch (P.6-2)
8.
Seat heater switch (if so equipped)
(P.2-38) or Climate controlled seat switch
(if so equipped) (P.2-40)
9.
Soft top operating switch (for Roadster
models)
(P.3-23)
or
Rear
hatch
release
switch (for Coupe models) (P.3-19)
10.
SynchroRev Match mode (S-MODE) switch
(if so equipped) (P.5-18)
11.
Heater and air conditioner (P.4-25)
— Rear window defroster switch (P.2-33)
12.
Audio system (P.4-30)
13.
Power outlet (P.2-42)
14.
Glove box (P.2-44)
*: Refer to the separate Navigation Sys-
tem Owner’s Manual.
INSTRUMENT PANEL
2-14
Instruments and controls
If you have a flat tire, replace it
with a spare tire (if so equipped)
or repair it with the tire puncture
repair kit (if so equipped) as soon
as possible. If no tire is flat and all
tires
are
properly
inflated,
it
is
recommended
you
consult
a
NISSAN dealer.
.
Since
the
spare
tire
is
not
equipped with the TPMS, when a
spare tire is mounted or a wheel
is
replaced,
the
TPMS
will
not
function and the low tire pressure
warning
light
will
flash
for
ap-
proximately 1 minute. The light
will remain on after the 1 minute.
Have your tires replaced and/or
TPMS system reset as soon as
possible. It is recommended you
visit a
NISSAN dealer for these
services.
.
Replacing
tires
with
those
not
originally
specified
by
NISSAN
could affect the proper operation
of the TPMS.
CAUTION
.
The TPMS is not a substitute for
the regular tire pressure check.
Be sure to check the tire pressure
regularly.
.
If the vehicle is being driven at
speeds of less than 16 MPH (25
km/h), the TPMS may not operate
correctly.
.
Be sure
to install
the specified
size of tires to the four wheels
correctly.
Master warning light
When the ignition switch is in the ON
position, the master warning light illumi-
nates if any of the following are displayed
on the vehicle information display:
.
No key warning
.
Low fuel warning
.
Low washer fluid warning
.
Parking brake release warning
.
Door/rear hatch/trunk open warning
.
Loose fuel cap warning
.
Check tire pressure warning
.
Extended storage fuse warning
See “Vehicle information display” (P.2-19).
Seat belt warning light and
chime
The light and chime remind you to fasten
seat belts. The light illuminates whenever
the ignition switch is pushed to the ON
position, and will remain illuminated until
the driver’s seat belt is fastened. At the
same time, the chime will sound for about
6 seconds unless the driver’s seat belt is
securely fastened.
The seat belt warning light for the front
passenger will illuminate if the seat belt is
not fastened when the front passenger’s
seat
is
occupied.
For
approximately
5
seconds after the ignition switch is in
the ON
position,
the
system
does not
activate the warning light for the front
passenger.
See “Seat belts” (P.1-10) for precautions on
seat belt usage.
Supplemental air bag warning
light
After pushing the ignition switch to the
ON
position,
the
supplemental
air
bag
warning light will illuminate. The air bag
warning light will turn off after about 7
seconds if the front air bag, side air bag
and curtain air bag systems and/or pre-
tensioner system are operational.
2-22
Instruments and controls
COLD tire pressure shown on the recom-
mended COLD tire pressure shown on the
Tire and Loading Information label. (See
“Tire Pressure Monitoring System (TPMS)”
(P.5-3) and “Tire Pressure Monitoring Sys-
tem (TPMS)” (P.6-3).
7. “TIMER” indicator
This
indicator
appears
when
the
set
“TIMER” indicator activates. You can set
the time for up to 6 hours. (See “Trip
computer” (P.2-23).)
8. Low outside temperature warn-
ing
This warning appears if the outside tem-
perature is below 37°F (3°C). The warning
can be set not to be displayed. (See “Trip
computer” (P.2-23).)
9. SynchroRev Match mode (S-
MODE) warning
This warning appears if a system mal-
function occurs. When the warning ap-
pears,
the
S-MODE
function
will
not
operate, but the manual transmission will
operate
normally
and
driving
can
be
continued. Have the system checked. It
is recommended you visit a NISSAN dealer
for this service.
10. Extended storage fuse warning
This warning may appear if the extended
storage
fuse
switch
is
not
pushed
in
(switched
on).
When
this
warning
ap-
pears, push in (switch on) the extended
storage fuse switch to turn off the warn-
ing. For more information, see “Extended
storage fuse switch” (P.8-19).
SIC4237
2-42
Instruments and controls
SIC3984
Center console
SIC3985
Lower glove box
The power outlet is located in the center
console and on the lower glove box.
CAUTION
.
The outlet and plug may be hot
during or immediately after use.
.
Do not use with accessories that
exceed
a
12
volt,
120W
(10A)
power draw. Do not use double
adapters or more than one elec-
trical accessory.
.
Use power outlet with the engine
running to avoid discharging the
vehicle battery.
.
Avoid using power outlet when
the air conditioner, headlights or
rear window defroster is on.
.
This power outlet is not designed
for use with a cigarette lighter
unit.
.
Push the plug in as far as it will
go. If good contact is not made,
the
plug
may
overheat
or
the
internal
temperature
fuse
may
blow.
.
Before inserting or disconnecting
a
plug,
be
sure
the
electrical
accessory being used is turned
OFF.
.
When not in use, be sure to close
the cap. Do not allow water or any
liquid to contact the outlet.
POWER OUTLET
language setting.
Scroll direction:
Set the scrolling behavior of the TUNE/
MENU knob to scroll UP or DOWN.
FM·AM radio operation
The
audio
system
operates
when
the
ignition switch is in the “ACC” or “ON”
position.
FM·AM button:
When the FM·AM button is pushed while
the audio system is off, the audio system
will turn on and the radio will turn on.
When the FM·AM button is pushed while
another audio source is already operat-
ing, it will automatically turn off, and the
radio will turn on.
To
change
the
radio
bands,
push
the
FM·AM
button
until
the
desired
band
appears.
AM
?
FM 1
?
FM 2
?
AM
TUNE/MENU knob:
When adjusting the broadcasting station
frequency manually, turn the TUNE/MENU
knob
until
the
preferred
frequency
is
achieved.
Seek tuning button:
When adjusting the broadcasting station
frequency
automatically,
push
the
button. When the system detects a
broadcasting station, it will stop at the
station.
Radio memory buttons:
During radio reception, pushing the radio
memory button for less than 2 seconds
will select the stored radio station.
The audio system can store up to 12 FM
station frequencies (six in each of FM 1and
FM 2) and 6 AM station frequencies.
To store the station frequency manually:
1.
Tune
to
the
desired
broadcasting
station frequency by using the
button.
2.
Push and hold a radio memory button
-
until a beep sounds. (The radio
mutes when the radio memory button
is pushed.)
3.
The channel indicator will display and
the radio mute disengages, indicating
that the memory is stored properly.
4.
Perform
steps
1
-
3
for
all
other
memory buttons.
If the battery cable is disconnected, or if
the audio fuse blows, the radio memory
will be erased. In such a case, reset the
desired stations.
SCAN button:
Push the SCAN button to tune from low
to high frequencies and stops at each
broadcasting station for 5 seconds. Push-
ing the SCAN button again during this 5
seconds period will stop SCAN tuning and
the
radio
will
remain
tuned
to
that
station.
If the SCAN button is not pushed within 5
seconds, SCAN tuning moves to the next
station.
CD player operation
The
audio
system
operates
when
the
ignition switch is in the “ACC” or “ON”
position.
Loading:
Insert a CD into the slot with the label side
facing up. The CD will be guided auto-
matically
into
the
slot
and
will
start
playing. After loading the CD, the number
of tracks and the playtime will appear on
the display.
CAUTION
Do not force the CD into the slot. This
could damage the player.
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-45
4-54
Center display, heater, air conditioner, audio, phone and voice recognition systems
.
UPDATING
(When
the
satellite
radio
subscription is not active)
SCAN tuning:
Push the SCAN tuning button to tune
from low to high frequencies and stop at
each broadcasting station/channel for 5
seconds. Pushing the button again during
this
5
seconds
period
will
stop
SCAN
tuning and the radio will remain tuned
to that station/channel.
If the SCAN tuning button is not pushed
within 5 seconds, SCAN tuning moves to
the next station/channel.
to
Station memory operations:
12 stations/channels can be set for the
FM band (6 each for FM1 and FM2), 18 for
SiriusXM Satellite Radio (6 each for XM1,
XM2 and XM3) and 6 stations can be set
for the AM band.
1.
Choose the radio band using the radio
band select button.
2.
Tune to the desired station/channel
using the SEEK/TRACK, SCAN button
or the radio TUNE knob.
3.
Push
and
hold
the
desired
station
preset button
to
until the radio
mutes.
4.
The station indicator will then come
on and the sound will resume. Mem-
orizing is now complete.
5.
Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if
the fuse opens, the radio memory will be
erased. In that case, reset the desired
stations/channels.
List (AM and FM radio):
When
the
“List”
key
on
the
display
is
selected while the FM or AM radio is being
played,
the
preset
station
list
will
be
displayed.
If
1
of
the
6
preset
stations
listed
is
touched and held, the current station will
be stored as the new preset.
Menu (SiriusXM Satellite Radio):
When the “Menu” key on the display is
selected while the SiriusXM Satellite Radio
is
being
played,
the
menu
list
will
be
displayed.
The following items are available.
.
Preset List
Displays the preset channel list. If 1 of
the 6 preset stations listed is touched
and held, the current station will be
stored as the new preset.
.
Customize Channel List
Selects specific channels to skip while
using the TUNE, SEEK/CATEGORY or
Menu-Categories feature.
.
Favorite Artists & Songs
Stores the current artist or song that
is being played. Touch the “Alert” key
to be reminded when the stored artist
or song is playing on a station while
listening to SiriusXM Satellite Radio.
.
Categories
Selecting a category will go to the first
channel in that category as defined by
SiriusXM Satellite Radio.
.
Direct Tune
Inputs the channel number by using a
keypad.
Compact Disc (CD) player operation
Push the ignition switch to the ACC or ON
position and insert the Compact Disc (CD)
into the slot with the label side facing up.
The CD will be guided automatically into
the slot and start playing.
After
loading
the
CD,
the
number
of
tracks on the CD and the play time will
appear on the display.
If the radio is already operating, it will
automatically turn off and the CD will
play.
If the system has been turned off while
the CD was playing, pushing the ON·OFF
button will start the CD.
Do not use 3.1 in (8 cm) discs.
You should be aware that incomplete or
improper servicing may result in operat-
ing difficulties or excessive emissions, and
could affect your warranty coverage.
If in
doubt about any servicing, it is recom-
mended you have it done by a NISSAN
dealer.
JVC0785X
VQ37VHR ENGINE MODEL
1.
Fuse/fusible link holder
2.
Battery
3.
Radiator filler cap
4.
Engine oil dipstick
5.
Engine oil filler cap
6.
Brake fluid reservoir
7.
Clutch fluid reservoir (Manual Transmis-
sion models)
8.
Power steering fluid reservoir
9.
Window washer fluid reservoir
10
Air cleaner
11.
Drive belt location
12.
Engine coolant reservoir
13.
Fuse/fusible link holder
Do-it-yourself
8-3
ENGINE COMPARTMENT CHECK LOCATIONS
8-18
Do-it-yourself
SDI1479A
SDI2566
ENGINE COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could
damage
the
electrical
system
or
electronic control units or cause a
fire.
If
any
electrical
equipment
does
not
operate, check for an open fuse.
1.
Be sure the ignition switch is pushed
to the OFF or LOCK position and the
headlight switch is turned to OFF.
2.
Open the engine hood.
3.
Remove the fuse/fusible link holder
cover.
4.
Remove the fuse with the fuse puller
located
in
the
passenger
compart-
ment fuse box.
SDI1754
5.
If the fuse is open
, replace it with a
new fuse
. Spare fuses are stored in
the passenger compartment fuse box.
6.
If a new fuse also opens, have the
electrical
system
checked
and
re-
paired. It is recommended you visit a
NISSAN dealer for this service.
Fusible links
If
any
electrical
equipment
does
not
operate and fuses are in good condition,
check the fusible links. If any of these
fusible links are melted, replace only with
genuine NISSAN parts.
FUSES
SDI2361
PASSENGER COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could
damage
the
electrical
system
or
electronic control units or cause a
fire.
If
any
electrical
equipment
does
not
operate, check for an open fuse.
1.
Be sure the ignition switch is pushed
to the OFF or LOCK position and the
headlight switch is turned to OFF.
2.
Open the fuse box lid.
3.
Remove the fuse with the fuse puller
.
4.
If the fuse is open, replace it with a
new fuse. Spare fuses are stored in the
fuse box.
5.
If a new fuse also opens, have the
electrical
system
checked
and
re-
paired. It is recommended you visit a
NISSAN dealer for this service.
SDI2704
Extended storage fuse switch
To reduce battery drain, the extended
storage
fuse
switch
comes
from
the
factory switched off.
Prior to delivery of your vehicle, the switch
is pushed in (switched on) and should
always remain on.
If the extended storage fuse switch is not
pushed in (switched on), the “SHIPPING
MODE ON, PUSH STORAGE FUSE” warning
may appear on the vehicle information
display. See “Warnings and alerts” (P.2-21).
If
any
electrical
equipment
does
not
operate,
remove
the
extended
storage
fuse switch and check for an open fuse.
Do-it-yourself
8-19
8-20
Do-it-yourself
NOTE:
If
the
extended
storage
fuse
switch
malfunctions, or if the fuse is open, it
is not necessary to replace the switch.
In this case, remove the extended sto-
rage fuse switch and replace it with a
new fuse of the same rating.
How to remove the extended storage
fuse switch:
1.
To remove the extended storage fuse
switch, be sure the ignition switch is in
the OFF or LOCK position.
2.
Be sure the headlight switch is in the
OFF position.
3.
Remove the fuse box cover.
4.
Pinch the locking tabs
found on
each side of the storage fuse switch.
5.
Pull the storage fuse switch straight
out from the fuse box
.
SDI2451
CAUTION
Be careful not to allow children to
swallow
the
battery
and
removed
parts.
Replace the battery as follows:
1.
Remove the mechanical key from the
key.
2.
Insert a small screwdriver into the slit
of the corner and twist it to separate
the upper part from the lower part.
Use a cloth to protect the casing.
3.
Replace the battery with a new one.
Recommended battery:
CR2032 or equivalent
.
Do not touch the internal circuit
and electric terminals as doing so
could cause a malfunction.
.
Hold
the
battery
by
the
edges.
Holding
the
battery
across
the
contact points will seriously deplete
the storage capacity.
.
Make sure that the
+
side faces the
bottom case.
INTELLIGENT KEY BATTERY REPLACEMENT