Infiniti QX70/FX - 2016 Fuse Box Diagram

Infiniti QX70/FX - 2016 Fuse Box Diagram

0-8
Illustrated table of contents
GUID-64430E38-4D64-41A9-9A8D-212C3600A5A4
JVC0209X
1.
Side ventilator (P.4-54)
2.
Paddle shifter (if so equipped) (P.5-18)
3.
Meters and gauges (P.2-6)
4.
Center ventilator (P.4-54)
5.
Center multi-function control panel
— Navigation
system*
(if
so
equipped)
— Vehicle
information
and
setting
buttons (P.4-9)
— RearView Monitor (if so equipped)
(P.4-25)
— Around
View
®
Monitor
(if
so
equipped) (P.4-32)
6.
Center display (P.4-3)
7.
Clock (P.2-49)
8.
Hazard warning flasher switch (P.6-2)
9.
Front passenger supplemental air bag
(P.1-43)
10. Hood release handle (P.3-18)
11. Fuse box cover (P.8-22)
12. Parking brake (P.5-21)
13. Steering wheel
— Horn (P.2-44)
— Driver supplement air bag (P.1-43)
14. Push-button ignition switch (P.5-11)
15. Front passenger air bag status light
(P.1-48)
16. Rear window defroster switch (P.2-38)
17. Power outlet (P.2-50)
18. Automatic climate control system
(P.4-54)
19. Audio system (P.4-58)
20. Glove box lid release handle (P.2-53)
*: Refer to the separate Navigation System
Owner’s Manual.
INSTRUMENT PANEL
0-10
Illustrated table of contents
GUID-0E9F7C61-12C7-4359-B3A7-F2B6A5B2D72A
SDI2262
VQ37VHR ENGINE
GUID-E1D33D79-85C2-48D3-81C3-5821CAFCD554
1.
Fuse/fusible link holder (P.8-22)
2.
Battery (P.8-15)
3.
Radiator filler cap (P.8-7)
4.
Engine oil dipstick (P.8-9)
5.
Engine oil filler cap (P.8-9)
6.
Brake fluid reservoir (P.8-13)
7.
Window washer fluid reservoir
(P.8-14)
8.
Power steering fluid reservoir (P.8-12)
9.
Air cleaner (P.8-18)
10. Drive belts (P.8-17)
11. Coolant reservoir (P.8-7)
ENGINE COMPARTMENT
GUID-7F14A382-7F82-4651-BDC7-0E12FD740023
JVC0209X
1.
Side ventilator
2.
Paddle shifter (if so equipped)
3.
Meters and gauges
4.
Center ventilator
5.
Center multi-function control panel
— Navigation
system*
(if
so
equipped)
— Vehicle
information
and
setting
buttons
— RearView Monitor (if so equipped)
— Around
View
®
Monitor
(if
so
equipped)
6.
Center display
7.
Clock
8.
Hazard warning flasher switch
9.
Front passenger supplemental air bag
10. Hood release handle
11. Fuse box cover
12. Parking brake
13. Steering wheel
— Horn
— Driver supplement air bag
14. Push-button ignition switch
15. Front passenger air bag status light
16. Rear window defroster switch
17. Power outlet
18. Automatic climate control system
19. Audio system
20. Glove box lid release handle
*: Refer to the separate Navigation System
Owner’s Manual.
Instruments and controls
2-5
INSTRUMENT PANEL
2-50
Instruments and controls
GUID-0D47D8B1-75C2-462A-AE78-C31F77B07718
SIC3631
Front
JVI1246X
Center console
SIC3835
Rear console
SIC3836
Cargo area
The power outlet is used for powering
electrical
accessories
such
as
cellular
telephones.
CAUTION
.
The outlet and plug may be hot during or
immediately after use.
.
Do not use with accessories that exceed
a 12 volt, 120W (10A) power draw. Do
not use double adapters or more than
one electrical accessory.
.
Use power outlet with the engine run-
ning to avoid discharging the vehicle
battery.
.
Avoid using power outlet when the air
conditioner, headlights or rear window
defroster is on.
.
This power outlet is not designed for use
with a cigarette lighter unit.
.
Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or
the
internal temperature
fuse may blow.
.
Before inserting or disconnecting a plug,
be sure the electrical accessory being
used is turned OFF.
POWER OUTLET
3-32
Pre-driving checks and adjustments
SIC3869
VANITY MIRROR
GUID-3780BCDB-5920-42A8-A7E5-61F0F7698B59
To use the front vanity mirror, pull down
the sun visor and pull up the cover.
GUID-5D3DB23B-FAEA-453A-AE25-5951BD40B382
The automatic drive positioner system has
the following features:
.
Entry/exit function
.
Seat synchronization function
.
Memory storage
ENTRY/EXIT FUNCTION
GUID-263AEFC2-F492-458F-9233-42DCA35945C7
This system is designed so that the driver’s
seat and steering column will automati-
cally move when the automatic transmis-
sion shift lever is in the P (Park) position.
This allows the driver to get into and out of
the driver’s seat more easily.
The driver’s seat will slide backward and
the steering wheel will move up when the
driver’s door is opened with the ignition
switch in the OFF position.
The driver’s seat and steering wheel will
return to the previous positions when one
of the following is operated:
.
When the ignition switch is pushed to
the ACC position after the driver’s door
is closed.
.
When the ignition switch is pushed to
the ON position.
The driver’s seat will not return to the
previous positions if the seat or steering
adjusting switch is operated when the seat
is at the exit position.
Cancel or activate entry/exit func-
tion
GUID-3363C195-263F-4FB5-BABF-B52E292D6892
The shift lever must be in the P (Park)
position with the ignition switch in the OFF
position.
The entry/exit function can be activated or
canceled by pressing and holding the SET
switch for more than 10 seconds.
The entry/exit function can also be acti-
vated or canceled if the “Lift Steering
Wheel on Exit” key or “Slide Driver Seat
Back on Exit” key is turned to ON or OFF in
the
“Comfort”
settings.
(See
“Vehicle
information and settings” (P.4-9).)
Initialize entry/exit function
GUID-CF566402-5592-4485-AD8B-9C26CE39C0D0
If the battery cable is disconnected, or if
the fuse opens, the entry/exit function will
not work though this function was set on
before. In such a case, after connecting the
battery or replacing with a new fuse, open
and close the driver’s door more than two
times after the ignition switch is turned
from the ON position to the LOCK position.
The entry/exit function will be activated.
AUTOMATIC DRIVE POSITIONER (if so
equipped)
3-34
Pre-driving checks and adjustments
“Outside mirrors” (P.3-30).
3.
Push the SET switch and, within 5
seconds, push the memory switch (1
or 2) fully for at least 1 second.
The
indicator
light
for
the
pushed
memory switch will stay on for approxi-
mately 5 seconds after pushing the
switch.
When the memory is stored in the
memory switch (1 or 2), a buzzer will
sound.
If
memory
is
stored
in
the
same
memory switch, the previous memory
will be deleted.
Linking Intelligent Key to a stored
memory position
GUID-E6D7628D-A73F-49DD-90F8-01DEB392FA18
The Intelligent Key can be linked to a
stored memory position with the following
procedure.
1.
Follow the steps for storing a memory
position.
2.
While the indicator light for the memory
switch being set is illuminated for 5
seconds, push the
button on the
Intelligent Key. If the indicator light
blinks, the Intelligent Key is linked to
that memory setting.
Push the ignition switch to the OFF posi-
tion, and then push the
button on the
Intelligent Key. The driver’s seat, steering
wheel and outside mirrors will move to the
memorized position or to the exit position
when the entry/exit
function is set to
active.
Confirming memory storage
GUID-E77C3565-8BEE-460B-9BBC-75EC608F88AD
.
Push the ignition switch to the ON
position and push the SET switch. If
the main memory has not been stored,
the indicator light will come on for
approximately 0.5 second. When the
memory has stored in position, the
indicator light will stay on for approxi-
mately 5 seconds.
.
If the battery cable is disconnected, or if
the fuse opens, the memory will be
canceled. In this case, reset the desired
position using the previous procedure.
.
If optional Intelligent Keys are added to
your vehicle, the memory storage pro-
cedure to switch 1 or 2 and linking
Intelligent Key procedure to a stored
memory position should be performed
again
for
each
Intelligent
Key.
For
additional Intelligent Key information,
see “Keys” (P.3-2).
Selecting the memorized position
GUID-2FEA9244-0775-4478-9531-20E8C2DBBEC5
1.
Move the shift lever to the P (Park)
position.
2.
Use one of the following methods to
move the driver’s seat, the outside
mirrors and the steering wheel.
.
Push the memory switch (1 or 2) fully
for at least 1 second.
.
Within 45 seconds of opening the
driver’s
door,
push
the
memory
switch (1 or 2) fully for at least 1
second.
The driver’s seat, steering column and
outside mirrors will move to the mem-
orized position or to the exit position
when the entry/exit function is set to
active with the indicator light flashing,
and then the light will stay on for
approximately 5 seconds.
SYSTEM OPERATION
GUID-4673EEB4-FD59-46C9-B5D8-0CE2C535A079
The automatic drive positioner system will
not work or will stop operating under the
following conditions:
.
When the vehicle speed is above 4 MPH
(7 km/h).
.
When
the
adjusting
switch
for
the
driver’s seat and steering column is
4-74
Monitor, heater, air conditioner, audio, phone and voice recognition systems
.
For SiriusXM Satellite Radio
Turn the radio tuning knob to seek
channels from all of the categories
when any category is not selected.
SEEK tuning/CATEGORY (CAT):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
.
For AM and FM radio
Push the SEEK·CAT or TRACK button to
tune from low to high or high to low
frequencies and to stop at the next
broadcasting station.
.
For SiriusXM Satellite Radio
Push the SEEK·CAT or TRACK button to
tune to the first channel of the next or
previous category.
During satellite radio reception, the follow-
ing notices will be displayed under certain
conditions.
.
NO SIGNAL (No signal is received while
the SAT tuner is connected.)
.
OFF AIR (Broadcasting signed off)
.
CHECK ANTENNA (Antenna connection
error)
.
LOADING (When the initial setting is
performed)
.
UPDATING
(When
the
satellite radio
subscription is not active)
SCAN tuning:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the radio SCAN button to tune from
low to high frequencies and stop at each
broadcasting station/channel for 5 sec-
onds. Pushing the button again during this
5 seconds period will stop SCAN tuning
and the radio will remain tuned to that
station/channel.
If the radio SCAN button is not pushed
within 5 seconds, SCAN tuning moves to
the next station/channel.
*
1
to
*
6
Station memory operations:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
12 stations/channels can be set for the FM
band (6 each for FM1 and FM2), 18 for
SiriusXM Satellite Radio (6 each for XM1,
XM2 and XM3) and 6 stations can be set for
the AM band.
1.
Choose the radio band using the radio
band select button.
2.
Tune to the desired station/channel
using the SEEK·CAT, TRACK, radio SCAN
button or the radio tuning knob.
3.
Push
and
hold
the
desired
station
preset button
*
1
to
*
6
.
4.
The station indicator will then come on
and the sound will resume. Memorizing
is now complete.
5.
Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if
the fuse opens, the radio memory will be
erased. In that case, reset the desired
stations/channels.
List (AM and FM radio) (models with
navigation system):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the “List” key on the display is
selected while the FM or AM radio is being
played,
the
preset
station
list
will
be
displayed.
If 1 of the 6 preset stations listed is
touched and held, the current station will
be stored as the new preset.
Menu (SiriusXM Satellite Radio) (models
with navigation system):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the “Menu” key on the display is
selected while the SiriusXM Satellite Radio
is being played, the menu list will be
displayed.
The following items are available.
.
Preset List
Displays the preset channel list. If 1 of
the 6 preset stations listed is touched
and held, the current station will be
stored as the new preset.
GUID-591BFA5B-ACC0-4C10-805D-84A972DE4007
SDI2262
VQ37VHR ENGINE
GUID-A9A92F72-9984-4610-9A98-DDA348D7EADC
1.
Fuse/fusible link holder
2.
Battery
3.
Radiator filler cap
4.
Engine oil dipstick
5.
Engine oil filler cap
6.
Brake fluid reservoir
7.
Window washer fluid reservoir
8.
Power steering fluid reservoir
9.
Air cleaner
10. Drive belts
11. Coolant reservoir
GUID-D578AF43-9C89-4D61-B7ED-7173E3DD4951
The engine cooling system is filled at the
factory with a pre-diluted mixture of 50%
Genuine NISSAN Long Life Antifreeze/Cool-
ant (blue) and 50% water to provide year-
round anti-freeze and coolant protection.
The antifreeze solution contains rust and
corrosion
inhibitors.
Additional
engine
cooling system additives are not neces-
sary.
WARNING
.
Never remove the radiator or coolant
reservoir cap when the engine is hot.
Wait until the engine and radiator cool
down. Serious burns could be caused by
high pressure fluid escaping from the
radiator. See precautions in
If
your
vehicle overheats
(P.6-11) of this man-
ual.
.
The radiator is equipped with a pressure
type radiator cap. To prevent engine
damage, use only a genuine NISSAN
radiator cap.
Maintenance and do-it-yourself
8-7
ENGINE COMPARTMENT CHECK LOCATIONS
ENGINE COOLING SYSTEM
8-22
Maintenance and do-it-yourself
GUID-1FFE3F37-9A0E-403A-AB85-F46C763F61A1
SDI1479A
ENGINE COMPARTMENT
GUID-52624265-87A7-4571-8C28-08C50EC3EF99
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on the
fuse box cover. This
could
damage the
electrical system or cause a fire.
If
any
electrical
equipment
does
not
operate, check for an open fuse.
1.
Be sure the ignition switch is pushed to
the
OFF
or
LOCK
position
and
the
headlight switch is turned to OFF.
2.
Open the engine hood and remove the
cover on the battery.
3.
Remove the fuse/fusible link holder
cover.
4.
Remove the fuse with the fuse puller.
SDI1754
5.
If the fuse is open
*
A
, replace it with a
new fuse
*
B
. Spare fuses are stored in
the passenger compartment fuse box.
6.
If a new fuse also opens, have the
electrical system checked and repaired
by an INFINITI retailer.
Fusible links
GUID-D884C9A5-FCA0-409B-890B-D500A8CB43BA
If
any
electrical
equipment
does
not
operate and fuses are in good condition,
check the fusible links. If any of these
fusible links are melted, replace only with
genuine INFINITI parts.
FUSES
SDI2034
PASSENGER COMPARTMENT
GUID-9F151796-01BF-4EB6-89CB-D2932E45E349
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on the
fuse box cover. This
could
damage the
electrical system or cause a fire.
If
any
electrical
equipment
does
not
operate, check for an open fuse.
1.
Be sure the ignition switch is pushed to
the
OFF
or
LOCK
position
and
the
headlight switch is turned to OFF.
2.
Open the fuse box lid.
3.
Remove the fuse with the fuse puller
*
A
.
4.
If the fuse is open, replace it with a new
fuse.
5.
If a new fuse also opens, have the
electrical system checked and repaired
by an INFINITI retailer. Spare fuses are
stored in the fuse box.
SDI2704
Extended storage fuse switch (if so
equipped)
GUID-841E2582-90C7-4A31-95B9-BCD88C3499FD
To
reduce battery
drain,
the
extended
storage fuse switch comes from the factory
switched off. Prior
to delivery of
your
vehicle, the switch is pushed in (switched
on) and should always remain on.
If
any
electrical
equipment
does
not
operate, remove the extended storage fuse
switch and check for an open fuse.
NOTE:
If the extended storage fuse switch mal-
functions, or if the fuse is open, it is not
necessary to replace the switch. In this
Maintenance and do-it-yourself
8-23
8-24
Maintenance and do-it-yourself
case, remove the extended storage fuse
switch and replace it with a new fuse of the
same rating.
How to remove the extended storage fuse
switch:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
1.
To remove the extended storage fuse
switch, be sure the ignition switch is in
the OFF or LOCK position.
2.
Be sure the headlight switch is in the
OFF position.
3.
Remove the fuse box cover.
4.
Pinch the locking tabs
*
1
found on
each side of the storage fuse switch.
5.
Pull the storage fuse switch straight out
from the fuse box
*
2
.
GUID-C26BD3DD-C31B-406C-B9E9-1FBAAEABFC84
CAUTION
Be careful not to allow children to swallow
the battery and removed parts.
SDI2451
Replace the battery as follows:
1.
Release the lock knob at the back of the
Intelligent Key and remove the mechan-
ical key.
2.
Insert a flat-blade screwdriver
*
A
wrapped with a cloth into the slit
*
B
of the corner and twist it to separate the
INTELLIGENT KEY BATTERY REPLACEMENT