Infiniti QX60/JX - 2015 Fuse Box Diagram

Infiniti QX60/JX - 2015 Fuse Box Diagram

VQ35DE engine
1.
Power steering fluid reservoir (P. 8-12)
2.
Engine coolant reservoir (P. 8-7)
3.
Drive belt location (P. 8-17)
4.
Fuse box (P. 8-22)
5.
Engine oil filler cap (P. 8-9)
6.
Brake fluid reservoir (P. 8-13)
7.
Air cleaner (P. 8-18)
8.
Fuse box (P. 8-22)
9.
Fuse box/fusible links (P. 8-22)
10.
Fuse box (P. 8-22)
11.
Battery (P. 8-14)
12.
Engine oil dipstick (P. 8-9)
13.
Radiator cap (P. 8-7)
14.
Windshield-washer fluid reservoir
(P. 8-14)
Refer to the page number indicated in pa-
rentheses for operating details.
LDI2498
ENGINE COMPARTMENT CHECK
LOCATIONS
0-8
Illustrated table of contents
Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or the internal temperature
fuse may open.
When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.
120V OUTLET (if so equipped)
CAUTION
The outlet and plug may be hot during
or immediately after use.
Use power outlets with the engine run-
ning to avoid discharging the vehicle
battery.
Do not use accessories that exceed a
120V, 150W power draw. Do not use
double adaptors or more than one elec-
trical accessory.
Avoid using power outlets when the air
conditioner, headlights or rear window
defroster is on.
Before
inserting
or
disconnecting
a
plug, be sure the electrical accessory
being used is turned OFF.
Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or the internal temperature
fuse may open.
When not in use, be sure to close the
cap. Do not allow water or any other
liquid to contact the outlet.
2nd Row
LIC2215
2-46
Instruments and controls
Restarting the entry/exit function
If the battery cable is disconnected, or if the fuse
opens, the stored memory positions will be lost
and some of the functions will be restricted:
1. Drive the vehicle over 25 MPH (40 km/h).
OR
2. Open and close the driver’s door more than
two times with the ignition switch in the OFF
position.
The entry/exit function should now work properly.
SETTING MEMORY FUNCTION
The position of the following settings can be
linked to the Intelligent Key and the memorized
settings can be available for each Intelligent Key.
Climate control system
Navigation system (if so equipped)
Audio system
To use the memory function, set the climate,
navigation and audio systems to the driver’s pre-
ferred settings. Lock the doors with the Intelligent
Key. Each Intelligent Key may be set with the
driver’s individual preferences. When a new In-
telligent Key is used, “Connection with the key
has been done” will be displayed on the screen
and the memorized settings are available.
To engage the memorized settings, perform the
following:
1. Carry the Intelligent Key that is linked to the
memorized settings.
2. Unlock the doors by pushing the driver’s
door
handle
request
switch
or
the
UNLOCK
button on the Intelligent
Key.
3. Place the ignition switch in the “ON” posi-
tion. The settings linked to the Intelligent Key
will start.
For additional information, refer to “Heater and air
conditioner (automatic)” in the “Monitor, climate,
audio, phone and voice recognition systems”
section of this manual.
For additional information on using the Naviga-
tion System, refer to the separate Navigation
System Owner’s Manual.
For additional information on using the Audio
system, refer to “Audio system” in the “Monitor,
climate, audio, phone and voice recognition sys-
tems” section of this manual.
SYSTEM OPERATION
The automatic drive positioner system will not
work or will stop operating under the following
conditions:
When the vehicle speed is above 4 MPH
(7 km/h).
When any of the memory switches are
pushed while the automatic drive positioner
is operating.
When the adjusting switch for the driver’s
seat is turned on while the automatic drive
positioner is operating.
When the seat has already been moved to
the memorized position.
When no seat position is stored in the
memory switch.
When the shift lever is moved from P (Park)
to any other position.
3-36
Pre-driving checks and adjustments
The last station played will also come on when
the VOL/ON·OFF control knob is pressed ON.
*When the XM button is pressed, the satellite
radio reception will not be available unless an
optional satellite receiver and antenna are in-
stalled and a SiriusXM® Satellite Radio service
subscription is active. Satellite radio is not avail-
able in Alaska, Hawaii and Guam.
If a compact disc is playing when the XM button
is pressed, the compact disc will automatically be
turned off and the last radio station played will
come on.
TUNE/FOLDER (Tuning) knob
To
manually
tune
the
radio,
turn
the
TUNE/FOLDER knob to the right or left.
SEEK•CAT/TRACK tuning
button
For AM or FM:
Press
the
SEEK•CAT/TRACK
button
or
to tune from high to low or low to high
frequencies and stop at the next broadcasting
station.
For XM:
Press
the
SEEK•CAT/TRACK
button
or
to go to the first channel of the previous
or next category.
During satellite radio reception, the following no-
tices will be displayed under certain conditions.
NO SIGNAL (No signal is received while the
SAT tuner is connected)
OFF AIR (Broadcasting signed off)
CHECK ANTENNA (Antenna connection
error)
LOADING (When the initial setting is per-
formed)
UPDATING (When the satellite radio sub-
scription is not active)
SCAN tuning
Press the SCAN button to stop at each broad-
casting station for 5 seconds. Pressing the
SCAN button again during this 5 second period
will stop scan tuning and the radio will remain
tuned to that station. If the SCAN button is not
pressed within 5 seconds, scan tuning moves to
the next station.
1 to 6 Station memory operations
Six stations can be set for the AM band. Twelve
stations can be set for the FM band (6 for FM1, 6
for FM2). Eighteen channels can be set for the
satellite radio (6 for XM1, 6 for XM2, 6 for XM3).
1. Choose the radio band AM, FM1 or FM2
using the FM·AM select button, or choose
the satellite band XM1, XM2 or XM3 using
the XM button.
2. Tune to the desired station using manual,
SEEK or SCAN tuning. Press and hold any
of the desired station memory buttons (1 –
6) until the preset number is updated on the
display and the sound is briefly muted.
3. The channel indicator will then come on and
the sound will resume. Programming is now
complete.
4. Other buttons can be set in the same man-
ner.
If the battery cable is disconnected, or if the fuse
opens, the radio memory will be canceled. In that
case, reset the desired stations.
List (AM and FM)
Select the “List” key using the INFINITI controller
or touch-screen to see a list of the presets in the
AM, FM1 or FM2 preset banks.
Monitor, climate, audio, phone and voice recognition systems
4-71
VQ35DE engine
1.
Power steering fluid reservoir
2.
Engine coolant reservoir
3.
Drive belt location
4.
Fuse box
5.
Engine oil filler cap
6.
Brake fluid reservoir
7.
Air cleaner
8.
Fuse box
9.
Fuse box/fusible links
10
Fuse box
11.
Battery
12.
Engine oil dipstick
13.
Radiator cap
14.
Windshield-washer fluid reservoir
NOTE:
Engine cover removed for clarity.
The engine cooling system is filled at the factory
with
a
pre-diluted
mixture
of
50%
Genuine
NISSAN Long Life Antifreeze/Coolant (blue) and
50% water to provide year-round antifreeze and
coolant protection. The antifreeze solution con-
tains rust and corrosion inhibitors. Additional en-
gine cooling system additives are not necessary.
WARNING
Never remove the radiator or coolant
reservoir cap when the engine is hot.
Wait until the engine and radiator cool
down. Serious burns could be caused
by high pressure fluid escaping from
the radiator. For additional information,
refer to precautions in “If your vehicle
overheats” found in the “In case of
emergency” section of this manual.
The radiator is equipped with a pres-
sure type radiator cap. To prevent en-
gine
damage,
use
only
a
Genuine
NISSAN radiator cap.
CAUTION
Never use any cooling system additives
such as radiator sealer. Additives may
clog the cooling system and cause dam-
age to the engine, transmission and/or
cooling system.
When adding or replacing coolant, be
sure to use only Genuine NISSAN Long
Life
Antifreeze/Coolant
(blue)
or
equivalent. Genuine NISSAN Long Life
Antifreeze/Coolant (blue) is pre-diluted
to provide antifreeze protection to -34°
F (-37° C). If additional freeze protection
is needed due to weather where you
operate
your
vehicle,
add
Genuine
NISSAN Long Life Antifreeze/Coolant
(blue) concentrate following the direc-
tions on the container. If an equivalent
coolant
other
than
Genuine
NISSAN
Long Life Antifreeze/Coolant (blue) is
used, follow the coolant manufacturer’s
instructions to maintain minimum anti-
freeze protection to -34° F (-37° C). The
use of other types of coolant solutions
other than Genuine NISSAN Long Life
Antifreeze/Coolant (blue) or equivalent
may
damage
the
engine
cooling
system.
ENGINE COOLING SYSTEM
Maintenance and do-it-yourself
8-7
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not come on,
check for an open fuse.
1. Be sure the ignition switch and the headlight
switch are OFF.
2. Open the engine hood.
3. Remove the fuse box cover by pushing the
tab and lifting the cover up.
4. Remove the fuse with the fuse puller. The
fuse puller is located in the fuse block in the
passenger compartment.
5. If the fuse is open
±
A
, replace it with a new
fuse
±
B
.
6. If a new fuse also opens, have the electrical
system checked and repaired by an INFINITI
retailer.
Fusible links
If the electrical equipment does not operate and
fuses are in good condition, check the fusible
links. If any of these fusible links are melted,
replace with only Genuine NISSAN parts.
LDI2267
LDI0456
FUSES
8-22
Maintenance and do-it-yourself
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch and the headlight
switch are OFF.
2. Pull the fuse box cover to remove.
3. Remove the fuse with the fuse puller.
4. If the fuse is open
±
A
, replace it with an
equivalent good fuse
±
B
.
5. Push the fuse box cover to install.
6. If a new fuse also opens, have the electrical
system checked and repaired by an INFINITI
retailer.
Extended storage switch
If any electrical equipment does not operate,
remove the extended storage switch and check
for an open fuse.
NOTE:
The extended storage switch is used for
long term vehicle storage. Even if the ex-
tended storage switch is broken it is not
necessary to replace it. Replace only the
open fuse in the switch with a new fuse.
LDI2092
LDI0456
LDI2035
Maintenance and do-it-yourself
8-23
How
to
remove
the
extended
storage
switch:
1. To remove the extended storage switch, be
sure the ignition switch is in the OFF or
LOCK position.
2. Be sure the headlight switch is in the OFF
position.
3. Remove the fuse box cover.
4. Pinch the locking tabs
±
1
found on each
side of the storage switch.
5. Pull the storage switch straight out from the
fuse box
±
2
.
CAUTION
Be careful not to allow children to swallow
the battery or removed parts.
SDI1867
BATTERY REPLACEMENT
8-24
Maintenance and do-it-yourself
2. Locate the jumper harness connector under
the lower portion of the instrument panel.
The connector is taped to the wiring harness
±
1
as indicated.
The connector is marked with a white tag
with “elec brake conn”.
Wire color designation for electric trailer brake
controller jumper harness.
WIRE COLOR
NOTE
RED/GREEN
Vehicle stop lamp switch
to trailer brake controller.
BLACK
Brake controller ground
(-).
BROWN/WHITE
Trailer brake controller
switched output.
RED/BLUE
Not used
RED
Fused trailer brake con-
troller battery feed (B+).
3. Peel off the tape and connect the jumper
harness to the connector.
4. Release the parking brake.
5. Install the aftermarket electric trailer brake
controller according to the manufacturer’s
instructions.
Pre-towing tips
Be certain your vehicle maintains a level
position when a loaded and/or unloaded
trailer is hitched. Do not drive the vehicle if it
has an abnormal nose-up or nose-down
condition; check for improper tongue load,
overload, worn suspension or other possible
causes of either condition.
Connector Location
LTI2045
Connector
LTI2046
9-26
Technical and consumer information