Infiniti G Sedan - 2011 Fuse Box Diagram

Infiniti G Sedan - 2011 Fuse Box Diagram

1. Side ventilator (P. 4-27)
2. Meters and gauges (P. 2-4)
3. Center ventilator (P. 4-27)
4. Audio system (P. 4-38)
5. Clock (P. 2-39)
6. Center multi-function control panel
— Navigation system* (if so equipped)
— Vehicle information and setting buttons
(P. 4-7)
— Bluetooth
±
Hands-Free Phone System
(if so equipped) (P. 4-84, P. 4-95)
— Audio system (P. 4-38)
7. Center
display
(P. 4-2)/Navigation
sys-
tem* (if so equipped)
8. Hazard warning flasher switch (P. 2-36)
9. Front
passenger
supplemental
air
bag
(P. 1-40)
10. Fuse box cover (P. 8-21)
11. Parking brake (for Automatic Transmis-
sion models)
— Parking (P. 5-18)
12. Push-button ignition switch (P. 5-8)
13. Automatic climate control system
(P. 4-28)
14. Cigarette
lighter
and
ashtray
(if
so
equipped) (P. 2-41) or storage box (if so
equipped) (P. 2-46)
— Power outlet (if so equipped) (P. 2-40)
15. Parking brake (for Manual Transmission
models)
— Parking (P. 5-18)
16. Heated
seat
switch
(if
so
equipped)
(P. 2-37)
17. SNOW
mode
switch
(if
so
equipped)
(P. 2-39)
18. Rear window and outside mirror (if so
equipped) defogger switch (P. 2-31)
19. Glove box lid release handle (P. 2-44)
20. Trunk release power cancel switch
(P. 3-19)
*: Refer to the separate Navigation System
Owner’s Manual.
SSI0671
INSTRUMENT PANEL
Illustrated table of contents
0-11
VQ25HR/VQ37VHR ENGINE
1. Fuse/fusible link holder (P. 8-21)
2. Battery (P. 8-14)
3. Engine oil filler cap (P. 8-9)
4. Brake fluid reservoir (P. 8-13)
5. Clutch fluid reservoir (Manual Transmis-
sion models) (P. 8-13)
6. Window washer fluid reservoir (P. 8-14)
7. Power steering fluid reservoir (P. 8-12)
8. Air cleaner (P. 8-18)
9. Radiator filler cap (P. 8-8)
10. Drive belts (P. 8-17)
11. Coolant reservoir (P. 8-8)
12. Engine oil dipstick (for VQ37VHR engine
model) (P. 8-9)
13. Engine oil dipstick (for VQ25HR engine
model) (P. 8-9)
SDI2709
ENGINE COMPARTMENT
Illustrated table of contents
0-13
1. Side ventilator (P. 4-27)
2. Meters and gauges (P. 2-4)
3. Center ventilator (P. 4-27)
4. Audio system (P. 4-38)
5. Clock (P. 2-39)
6. Center multi-function control panel
— Navigation system* (if so equipped)
— Vehicle information and setting buttons
(P. 4-7)
— Bluetooth
±
Hands-Free Phone System
(if so equipped) (P. 4-84, P. 4-95)
— Audio system (P. 4-38)
7. Center
display
(P. 4-2)/Navigation
sys-
tem* (if so equipped)
8. Hazard warning flasher switch (P. 2-36)
9. Front
passenger
supplemental
air
bag
(P. 1-40)
10. Fuse box cover (P. 8-21)
11. Parking brake (for Automatic Transmis-
sion models)
— Parking (P. 5-18)
12. Push-button ignition switch (P. 5-8)
13. Automatic climate control system
(P. 4-28)
14. Cigarette
lighter
and
ashtray
(if
so
equipped) (P. 2-41) or storage box (if so
equipped) (P. 2-46)
— Power outlet (if so equipped) (P. 2-40)
15. Parking brake (for Manual Transmission
models)
— Parking (P. 5-18)
16. Heated
seat
switch
(if
so
equipped)
(P. 2-37)
17. SNOW
mode
switch
(if
so
equipped)
(P. 2-39)
18. Rear window and outside mirror (if so
equipped) defogger switch (P. 2-31)
19. Glove box lid release handle (P. 2-44)
20. Trunk release power cancel switch
(P. 3-19)
*: Refer to the separate Navigation System
Owner’s Manual.
SSI0671
INSTRUMENT PANEL
Instruments and controls
2-3
The power outlet is located in the center con-
sole and storage box (if so equipped).
CAUTION
The outlet and plug may be hot during or
immediately after use.
Do not use with accessories that exceed a 12
volt, 120W (10A) power draw. Do not use
double adapters or more than one electrical
accessory.
Use power outlet with the engine running to
avoid discharging the vehicle battery.
Avoid using power outlet when the air condi-
tioner, headlights or rear window defroster
is on.
This power outlet is not designed for use
with a cigarette lighter unit.
Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may blow.
Before inserting or disconnecting a plug, be
sure the electrical accessory being used is
turned OFF.
When not in use, be sure to close the cap. Do
not allow water to contact the outlet.
Automatic transmission models
SIC4302
Manual transmission models
SIC4684
Automatic transmission models
SIC4316
POWER OUTLET
2-40
Instruments and controls
AND SETTINGS” in the “4. Monitor, climate,
audio, phone and voice recognition systems”
section.)
Initialize entry/exit function
If the battery cable is disconnected, or if the
fuse opens, the entry/exit function will not work
though this function was set on before. In such
a case, after connecting the battery or replacing
with a new fuse, open and close the driver’s
door more than two times after the ignition
switch is turned from the ON position to the
LOCK position. The entry/exit function will be
activated.
SEAT SYNCHRONIZATION FUNCTION
The seat synchronization function automatically
adjusts the positions of the steering wheel and
outside mirrors when the seat is adjusted using
the power seat switches.
However, the steering wheel and outside mir-
rors will not move if the seat is adjusted over
the maximum thresholds. The system considers
that the steering wheel and outside mirror
adjustments are not necessary because the
seat may not be adjusted for the driving posi-
tion. Note that the function is set to disabled as
the factory default setting.
The seat synchronization function operates un-
der the following conditions:
The ignition switch is in the ON position.
The selector lever is in the P (Park) position
(Automatic
Transmission
models)
or
the
parking brake is applied (Manual Transmis-
sion models).
The seatback is raised (Coupe).
If the outside mirrors or the steering wheel
reaches its maximum adjustment, the function
is automatically disabled. Restart the function
by selecting a previously stored seat memory
position using the memory switches (1 or 2). An
Intelligent Key that was previously linked to the
stored seat memory can also be used to restart
the function.
If a seat position was not previously stored in
the seat memory, restart the function by adjust-
ing the steering wheel and outside mirrors
manually for your best driving position and then
drive the vehicle above 4 MPH (7 km/h).
Cancel or activate seat
synchronization function
For Automatic Transmission models:
The selector lever must be in the P (Park)
position with the ignition switch in the ACC
position.
SPA2322
3-30
Pre-driving checks and adjustments
For Manual Transmission models:
The parking brake must be applied with the
ignition switch in the ACC position.
The seat synchronization function can be acti-
vated or canceled by pushing and holding the
SET switch for more than 10 seconds while the
ignition switch is in the ACC position.
The indicator lights on the memory switches (1
and 2) will blink once when the function is
canceled, and the indicator lights will blink
twice when the function is activated. Note that
the indicator lights may illuminate after 5 sec-
onds while holding the SET switch. This indi-
cates readiness for linking the Intelligent Key to
a stored memory position. Keep the SET switch
pushed for more than 10 seconds to turn on or
off the seat synchronization function.
MEMORY STORAGE
Two positions for the driver’s seat, steering
column and outside mirrors can be stored in the
automatic
drive
positioner
memory.
Follow
these procedures to use the memory system.
1.
Automatic transmission models:
Move
the
selector
lever
to
the
P
(Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback (Coupe).
3. Push the ignition switch to the ON posi-
tion.
4. Adjust the driver’s seat, steering column
and outside mirrors to the desired posi-
tions by manually operating each adjust-
ing switch. For additional information, see
“SEATS” in the “1. Safety — Seats, seat
belts and supplemental restraint system”
section and “TILT/TELESCOPIC STEERING”
page 3-24 and “OUTSIDE MIRRORS” ear-
lier in this section.
5. Push the SET switch and, within 5 sec-
onds, push the memory switch (1 or 2)
fully for at least 1 second.
The indicator light for the pushed memory
switch will stay on for approximately 5 sec-
onds after pushing the switch.
If memory is stored in the same memory
switch, the previous memory will be deleted.
Linking Intelligent Key to a stored
memory position
The Intelligent Key can be linked to a stored
memory position with the following procedure.
1. Follow the steps for storing a memory
position.
2. While the indicator light for the memory
switch being set is illuminated for 5 sec-
onds, push the
button on the Intel-
ligent Key. If the indicator light blinks, the
Intelligent Key is linked to that memory
setting.
Push the ignition switch to the OFF position,
and then push the
button on the Intelli-
gent Key. The driver’s seat, steering wheel and
outside mirrors will move to the memorized
position.
Confirming memory storage
Push the ignition switch to the ON position
and push the SET switch. If the main memory
has not been stored, the indicator light will
come
on
for
approximately
0.5
second.
When the memory has stored in position, the
indicator light will stay on for approximately
5 seconds.
If the battery cable is disconnected, or if the
fuse opens, the memory will be canceled. In
this case, reset the desired position using
the previous procedure.
If optional Intelligent Keys are added to your
vehicle, the memory storage procedure to
switch 1 or 2 and linking Intelligent Key
procedure
to
a
stored
memory
position
should be performed again for each Intelli-
Pre-driving checks and adjustments
3-31
or
to tune from low to high or high to
low frequencies and to stop at the next
broadcasting station.
For XM Satellite Radio
Push the SEEK·CAT or TRACK button
or
to tune to the first channel of the
next or previous category.
During satellite radio reception, the following
notices will be displayed under certain condi-
tions.
NO SIGNAL (No signal is received while the
SAT tuner is connected.)
OFF AIR (Broadcasting signed off)
CHECK ANTENNA (Antenna connection error)
LOADING (When the initial setting is per-
formed)
UPDATING (When the satellite radio sub-
scription is not active)
or
SCAN tuning :
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broadcast-
ing station/channel for 5 seconds. Pushing the
button again during this 5 seconds period will
stop SCAN tuning and the radio will remain
tuned to that station/channel.
If the SCAN tuning button is not pushed within
5 seconds, SCAN tuning moves to the next
station/channel.
PRESET select (Type B) :
Push the PRESET select button to go to the next
PRESET. After choosing from the PRESET A, B or
C, you can select the desired station using the
INFINITI controller or pushing the station preset
buttons
±
1
to
±
6
.
±
1
to
±
6
Station memory operations :
12 stations/channels can be set for the FM band
(6 each for FM1 and FM2), 18 for XM radio (6
each for XM1, XM2 and XM3) and 6 stations can
be set for the AM band.
1. Choose the radio band using the radio
band select button.
2. Tune to the desired station/channel using
the SEEK·CAT, TRACK, SCAN button or the
radio TUNE knob.
3. Push and hold the desired station preset
button
±
1
to
±
6
until the radio mutes.
4. The station indicator will then come on
and the sound will resume. Memorizing is
now complete.
5. Other buttons can be set in the same
manner.
If the battery cable is disconnected, or if the
fuse opens, the radio memory will be erased. In
that case, reset the desired stations/channels.
List (AM and FM radio) (models with navigation
system) :
When the “List” key on the display is selected
while the FM or AM radio is being played, the
preset station list will be displayed.
If 1 of the 6 preset stations listed is touched and
held, the current station will be stored as the
new preset.
Menu (XM Satellite Radio) (models with naviga-
tion system) :
When the “Menu” key on the display is selected
while the XM Satellite Radio is being played,
the menu list will be displayed.
The following items are available.
Preset List
Displays the preset channel list. If 1 of the 6
preset stations listed is touched and held,
the current station will be stored as the new
preset.
Customize Channel List
Selects specific channels to skip while using
the
TUNE,
SEEK/CATEGORY
or
Menu-
Categories feature.
4-56
Monitor, climate, audio, phone and voice recognition systems
VQ25HR/VQ37VHR ENGINE
1. Fuse/fusible link holder
2. Battery
3. Engine oil filler cap
4. Brake fluid reservoir
5. Clutch fluid reservoir (Manual Transmis-
sion models)
6. Window washer fluid reservoir
7. Power steering fluid reservoir
8. Air cleaner
9. Radiator filler cap
10. Drive belts
11. Engine coolant reservoir
12. Engine oil dipstick (for VQ37VHR engine
model)
13. Engine oil dipstick (for VQ25HR engine
model)
SDI2709
ENGINE COMPARTMENT CHECK
LOCATIONS
Maintenance and do-it-yourself
8-7
If the brakes do not operate properly, have the
brakes checked by an INFINITI retailer.
SELF-ADJUSTING BRAKES
Your vehicle is equipped with self-adjusting
brakes.
The disc-type brakes self-adjust every time the
brake pedal is applied.
WARNING
See an INFINITI retailer for a brake system
check if the brake pedal height does not return
to normal.
BRAKE PAD WEAR WARNING
The disc brake pads have audible wear warn-
ings. When a brake pad requires replacement, it
will make a high pitched scraping sound when
the vehicle is in motion. This scraping sound
will first occur only when the brake pedal is
depressed. After more wear of the brake pad,
the sound will always be heard even if the brake
pedal
is
not
depressed.
Have
the
brakes
checked as soon as possible if the wear warn-
ing sound is heard.
Under some driving or climate conditions, occa-
sional brake squeak, squeal or other noise may
be heard. Occasional brake noise during light to
moderate stops is normal and does not affect
the function or performance of the brake sys-
tem.
Proper brake inspection intervals should be fol-
lowed.
For additional information, see the main-
tenance log section of your “INFINITI Service
and Maintenance Guide” for maintenance inter-
vals.
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower amperage
rating than that specified on the fuse box cover.
This could damage the electrical system or
cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch is pushed to
the OFF or LOCK position and the head-
light switch is turned to OFF.
SDI1479A
BRAKES
FUSES
Maintenance and do-it-yourself
8-21
2. Open the engine hood and remove the
cover on the battery and the fuse/fusible
link holder.
3. Remove
the
fuse/fusible
link
holder
cover.
4. Remove the fuse with the fuse puller.
5. If the fuse is open
±
A
, replace it with a
new fuse
±
B
. Spare fuses are stored in the
passenger compartment fuse box.
6. If a new fuse also opens, have the elec-
trical system checked and repaired by an
INFINITI retailer.
Fusible links
If any electrical equipment does not operate
and fuses are in good condition, check the
fusible links. If any of these fusible links are
melted,
replace
only
with
genuine
INFINITI
parts.
SDI1754
8-22
Maintenance and do-it-yourself
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower amperage
rating than that specified on the fuse box cover.
This could damage the electrical system or
cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch is pushed to
the OFF or LOCK position and the head-
light switch is turned to OFF.
2. Open the fuse box lid.
3. Remove the fuse with the fuse puller
±
A
.
4. If the fuse is open, replace it with a new
fuse.
5. If a new fuse also opens, have the electri-
cal system checked and repaired by an
INFINITI retailer. Spare fuses are stored in
the fuse box.
Extended storage switch (if equipped)
To reduce battery drain, the extended storage
switch comes from the factory switched off.
Prior to delivery of your vehicle, the switch is
pushed in (switched on) and should always
remain on.
If any electrical equipment does not operate,
remove the extended storage switch and check
for an open fuse.
SDI2034
SDI2704
Maintenance and do-it-yourself
8-23
NOTE:
If the extended storage switch malfunctions, or
if the fuse is open, it is not necessary to replace
the switch. In this case, remove the extended
storage switch and replace it with a new fuse of
the same rating.
How to remove the extended storage switch:
1. To remove the extended storage switch,
be sure the ignition switch is in the OFF or
LOCK position.
2. Be sure the headlight switch is in the OFF
position.
3. Remove the fuse box cover.
4. Pinch the locking tabs
±
1
found on each
side of the storage switch.
5. Pull the storage switch straight out from
the fuse box
±
2
.
Replace the battery as follows:
1. Release the lock knob at the back of the
Intelligent Key and remove the mechanical
key.
2. Insert
a
flat-blade
screwdriver
±
A
wrapped with a cloth into the slit
±
B
of
the corner and twist it to separate the
upper part from the lower part.
3. Replace the battery with a new one.
Recommended battery: CR2032 or equivalent.
Do
not
touch
the
internal
circuit
and
electric terminals as it could cause a
malfunction.
Hold the battery by the edges. Holding
the battery across the contact points will
seriously deplete the storage capacity.
Make
sure
that
the
+
side
faces
the
bottom of the case.
4. Align the tips of the upper and lower
parts, and then push them together until
it is securely closed.
5. Push the buttons two or three times to
check its operation.
SDI1834
SDI2042
INTELLIGENT KEY BATTERY REPLACEMENT
8-24
Maintenance and do-it-yourself