Jeep Wrangler Unlimited - 2017 Fuse Box Diagram

Jeep Wrangler Unlimited - 2017 Fuse Box Diagram

Electrical Power Outlets
There are two 12 Volt (13 Amp) auxiliary power outlets that
can provide power for accessories designed for use with
the standard power outlet adapters.
The front power outlet is located in the center of the
instrument panel below the climate controls, and is pow-
ered from the ignition switch. Power is available when the
ignition switch is in the ON or ACC position.
When the optional cigar lighter heating element is used in
the power outlet, it heats when pushed in and pops out
automatically when ready for use.
To preserve the heating
element, do not hold the lighter in the heating position.
A second power outlet is located inside the center console
and is powered directly from the vehicle battery.
CAUTION!
Do not exceed the maximum power of 160 Watts
(13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power
rating is exceeded the fuse protecting the system will
need to be replaced.
Power outlets are designed for accessory plugs only.
Do not insert any other object in the power outlets as
this
will
damage
the
outlet
and
blow
the
fuse.
Improper use of the power outlet can cause damage
not covered by your New Vehicle Limited Warranty.
Front Power Outlet
3
GETTING TO KNOW YOUR VEHICLE
175
On vehicles equipped with a rear subwoofer, there is a
third power outlet located in the right rear cargo area.
WARNING!
To avoid serious injury or death:
Do not insert any objects into the receptacles.
Do not touch with wet hands.
Close the lid when not in use.
If this outlet is mishandled, it may cause an electric
shock and failure.
Rear Power Outlet — If Equipped
Power Outlet Fuse Locations
1 — M36 Fuse 20 A Yellow Power Outlet Console Bin
2 — M6 Fuse 20 A Yellow Cigar Lighter Instrument Panel
3 —
M7 Fuse 20 A Yellow Power Outlet Rear With Sub Woofer (Opt.)
176
GETTING TO KNOW YOUR VEHICLE
mileage was before the repair or service. It is a good idea
for you to make a record of the odometer reading before
the repair/service, so that you can be sure that it is
properly reset, or that the door jamb sticker is accurate if
the odometer must be reset at zero.
Vehicle Odometer Messages
All messages will display in the instrument cluster display,
if equipped. Refer to “Instrument Cluster Display— If
Equipped” in this section for further information.
When
the
appropriate
conditions
exist,
the
following
odometer messages will display:
ECO — Fuel Saver Indicator
door — Door Open
gATE — Swing Gate Open
LoW tirE — Low Tire Pressure
HOTOIL — Oil Temperature Above Normal Limits
gASCAP — Fuel Cap Fault
noFUSEFuse Fault
CHAngE OIL — Oil Change Required
6.
Telltales
Hard and Soft Telltales (Symbols) appear based on
specific behaviors.
7.
Instrument
Cluster
Display
/
Compass
Mini-Trip
Computer Display — If Equipped
When the appropriate conditions exist, this display
shows the instrument cluster display messages. Refer
to “Instrument Cluster Display” in “Getting To Know
Your Instrument Panel” for further information.
When the appropriate conditions exist, this display
shows the Mini-Trip Computer messages. Refer to
“Mini-Trip Computer” in “Getting To Know Your
Instrument Panel” for further information.
INSTRUMENT CLUSTER DISPLAY — IF EQUIPPED
Your vehicle may be equipped with an instrument cluster
display, which offers useful information to the driver. With
the ignition in the STOP/OFF mode, opening/closing of a
door will activate the display for viewing, and display the
total miles, or kilometers, in the odometer. Your instrument
cluster display is designed to display important informa-
tion about your vehicle’s systems and features. Using a
driver interactive display located on the instrument panel,
your instrument cluster display can show you how sys-
tems are working and give you warnings when they aren’t.
182
GETTING TO KNOW YOUR INSTRUMENT PANEL
Rear Tail, Stop, Turn Signal, And Backup Lamp
1. Remove the two inboard screws attaching the tail light
housing to the body.
DO NOT REMOVE THE OUT-
BOARD SCREWS AT ANY TIME.
2. Separate the housing from the body by pushing the
lamp inboard while pulling the lamp away from the
body.
3. Rotate the appropriate socket 1/4 turn counterclock-
wise, then remove it from the housing.
4. Pull the bulb straight from the socket to replace.
Center High-Mounted Stop Lamp (CHMSL)
The stop lamp is mounted on a bracket that extends
upward from the tailgate behind the spare tire. If service is
needed, obtain the LED/Cover Assembly from your local
authorized dealer.
1. Remove the spare tire.
2. Remove the four screws holding the lens/cover in place
on the spare tire carrier.
3. Disconnect the wire harness from the back of the LED
cover.
FUSES
WARNING!
When replacing a blown fuse, always use an appro-
priate replacement fuse with the same amp rating as
the original fuse. Never replace a fuse with another
fuse of higher amp rating. Never replace a blown
fuse with metal wires or any other material. Failure
to use proper fuses may result in serious personal
injury, fire and/or property damage.
(Continued)
Inboard Screw Location
7
IN CASE OF EMERGENCY
341
WARNING!
(Continued)
Before replacing a fuse, make sure that the ignition is
off and that all the other services are switched off
and/or disengaged.
If the replaced fuse blows again, contact an autho-
rized dealer.
If a general protection fuse for safety systems (air
bag system, braking system), power unit systems
(engine system, gearbox system) or steering system
blows, contact an authorized dealer.
General Information
The fuses protect electrical systems against excessive cur-
rent.
When a device does not work, you must check the electri-
cal circuit inside the fuse for a break/melt.
Also, please be aware that when using power outlets for
extended periods of time with the engine off may result in
vehicle battery discharge.
Blade Fuses
1 — Electrical Circuit
2 — Blade Fuse With Good Electrical Circuit
3 — Blade Fuse With Bad Electrical Circuit
342
IN CASE OF EMERGENCY
Totally Integrated Power Module
The Totally Integrated Power Module is located in the
engine compartment near the battery. This center contains
cartridge fuses, mini fuses, and relays. A label that identi-
fies each component is printed on the inside of the cover.
Cavity
Cartridge Fuse
Mini Fuse
Description
J1
J2
30 Amp Pink
Transfer Case Module
J3
J4
25 Amp Clear
Driver Door Node
J5
25 Amp Clear
Passenger Door Node
J6
40 Amp Green
Anti-Lock Brake System (ABS) Pump/
Stability Control System
J7
30 Amp Pink
Anti-Lock Brake System (ABS) Valve/
Stability Control System
J8
Totally Integrated Power Module
7
IN CASE OF EMERGENCY
343
Cavity
Cartridge Fuse
Mini Fuse
Description
J9
40 Amp Green
PZEV Sec Motor/Flex Fuel – If Equipped
J10
30 Amp Pink
Headlamp Wash Relay/Manifold Tuning Valve
J11
30 Amp Pink
Sway Bar
J12
J13
60 Amp Yellow
Ignition Off Draw (IOD) – Main
J14
40 Amp Green
Rear Defroster
J15
40 Amp Green
Front Blower
J17
40 Amp Green
Starter Solenoid
J18
20 Amp Blue
Powertrain Control Module (PCM) Trans
Range
J19
60 Amp Yellow
Radiator Fan
J20
30 Amp Pink
Front Wiper LO/HI
J21
20 Amp Blue
Front/Rear Washer
J22
Spare
M1
15 Amp Blue
Center High-Mounted Stop Light (CHMSL)/
Switch Stop Lamp Feed
M2
20 Amp Yellow
Relay Trailer Lighting (Stop lamp)
M3
20 Amp Yellow
Front/Rear Axle Locker Relay
M4
2 Amp Grey
Clock Spring
M5
25 Amp Clear
Power Inverter – If Equipped
344
IN CASE OF EMERGENCY
Cavity
Cartridge Fuse
Mini Fuse
Description
M6
20 Amp Yellow
Power Outlet #1/Rain Sensor
M7
20 Amp Yellow
Power Outlet #2 (BATT/ACC SELECT)
M8
20 Amp Yellow
Front Heated Seat
M9
20 Amp Yellow
Rear Heated Seat – If Equipped
M10
15 Amp Blue
Ignition Off Draw – Vehicle Entertainment
System, Satellite Digital Audio Receiver
(SDARS), DVD, Hands-Free Module, RA-
DIO, Antenna, Universal Garage Door
Opener, Vanity Lamp
M11
10 Amp Red
(Ignition Off Draw) Climate Control System,
Underhood Lamp
M12
30 Amp Green
Amplifier
M13
20 Amp Yellow
Ignition Off Draw – Cabin Compartment
Node, Wireless Control Module, SIREN,
Multifunction Control Switch
M14
20 Amp Yellow
Trailer Tow (Export Only)
M15
20 Amp Yellow
Climate Control System, Rear View Mirror,
Cabin Compartment Node, Transfer Case
Switch, Multi-Function Control Switch, Tire
Pressure Monitor, Glow Plug Module – Ex-
port Diesel Only
7
IN CASE OF EMERGENCY
345
Cavity
Cartridge Fuse
Mini Fuse
Description
M16
10 Amp Red
Airbag Module
M17
15 Amp Blue
Left Tail/License/Park Lamp
M18
15 Amp Blue
Right Tail/Park/Run Lamp
M19
25 Amp Clear
Auto Shut Down (ASD #1 and #2)
M20
15 Amp Blue
Cabin Compartment Node Interior Light,
Switch Bank
M21
20 Amp Yellow
Auto Shut Down (ASD #3)
M22
10 Amp Red
Right Horn (HI/LOW)
M23
10 Amp Red
Left Horn (HI/LOW)
M24
25 Amp Clear
Rear Wiper
M25
20 Amp Yellow
Fuel Pump, Diesel Lift Pump – Export Only
M26
10 Amp Red
Power Window Switch, Driver Window
Switch
M27
10 Amp Red
Ignition Switch Feed, Wireless Module
M28
10 Amp Red
Powertrain Control Module
M29
10 Amp Red
Powertrain
M30
15 Amp Blue
Wiper Motor Frt, J1962 Diagnostic Feed
M31
20 Amp Yellow
Backup Lamps
M32
10 Amp Red
Airbag Controller, TT EUROPE
M33
10 Amp Red
Powertrain Controller
346
IN CASE OF EMERGENCY
Cavity
Cartridge Fuse
Mini Fuse
Description
M34
10 Amp Red
Park Assist, Climate Control System, Head-
lamp Wash, Compass
M35
10 Amp Red
Heated Mirrors
M36
20 Amp Yellow
Power Outlet
M37
10 Amp Red
Anti-Lock Brake System, Electronic Stability
Control, Stop Lamp Switch, Fuel Pump Relay
M38
25 Amp Clear
Lock/Unlock Motors
CAUTION!
When installing the Integrated Power Module cover,
it is important to ensure the cover is properly posi-
tioned and fully latched. Failure to do so may allow
water to get into the Integrated Power Module, and
possibly result in an electrical system failure.
When replacing a blown fuse, it is important to use
only a fuse having the correct amperage rating. The
use of a fuse with a rating other than indicated may
result in a dangerous electrical system overload. If a
properly rated fuse continues to blow, it indicates a
problem in the circuit that must be corrected.
JACKING AND TIRE CHANGING
WARNING!
Do not attempt to change a tire on the side of the
vehicle close to moving traffic. Pull far enough off
the road to avoid the danger of being hit when
operating the jack or changing the wheel.
Being under a jacked-up vehicle is dangerous. The
vehicle could slip off the jack and fall on you. You
could be crushed. Never put any part of your body
under a vehicle that is on a jack. If you need to get
under a raised vehicle, take it to a service center
where it can be raised on a lift.
(Continued)
7
IN CASE OF EMERGENCY
347
ENGINE COMPARTMENT
3.6L Engine
1 — Integrated Power Module (Fuses)
7 — Washer Fluid Reservoir
2 — Battery
8 — Engine Coolant Reservoir
3 — Engine Oil Dipstick
9 — Air Cleaner Filter
4 — Automatic Transmission Dipstick (Under Engine Cover)
10 — Coolant Pressure Cap
5 — Engine Oil Fill
11 — Power Steering Fluid Reservoir
6 — Brake Fluid Reservoir
370
SERVICING AND MAINTENANCE
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.
The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect
the
accuracy
or
operation
of
the
compass
on
vehicles so equipped.
The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.
NOTE:
Do
not
exceed
the
maximum
power
of
160 Watts (13 Amps) at 12 Volts. If the
160 Watt (13 Amp) power rating is exceeded
the fuse protecting the system will need to be
replaced.
Power outlets are designed for accessory
plugs only. Do not insert any other object
in the power outlet as this will damage the
outlet and blow the fuse. Improper use of
the power outlet can cause damage not
covered by your new vehicle warranty.
Power Outlet Fuses
1 — #M7 Fuse 20 Amp Yellow – Power Outlet Rear (If Equipped)
2 — #M6 Fuse 20 Amp Yellow – Cigar Lighter Instrument Panel
3 — #M36 Fuse 20 Amp Yellow – Power Outlet Console Bin
63
Rear Tail, Stop, Turn Signal, And Backup
Lamp
1. Remove the two inboard screws attaching
the tail light housing to the body.
DO NOT
REMOVE THE OUTBOARD SCREWS AT ANY
TIME.
2. Separate the housing from the body by
pushing the lamp inboard while pulling
the lamp away from the body.
3. Rotate the appropriate socket 1/4 turn
counterclockwise, then remove it from the
housing.
4. Pull the bulb straight from the socket to
replace.
Center High-Mounted Stop Lamp (CHMSL)
The stop lamp is mounted on a bracket that
extends upward from the tailgate behind the
spare tire. If service is needed, obtain the
LED/Cover Assembly from your local autho-
rized dealer.
1. Remove the spare tire.
2. Remove the four screws holding the lens/
cover in place on the spare tire carrier.
3. Disconnect the wire harness from the
back of the LED cover.
FUSES
WARNING!
• When replacing a blown fuse, always use
an appropriate replacement fuse with
the same amp rating as the original fuse.
Never replace a fuse with another fuse of
higher
amp
rating.
Never
replace
a
blown fuse with metal wires or any other
material. Failure to use proper fuses may
result in serious personal injury, fire
and/or property damage.
• Before replacing a fuse, make sure that
the ignition is off and that all the other
services are switched off and/or disen-
gaged.
• If the replaced fuse blows again, contact
an authorized dealer.
• If a general protection fuse for safety
systems (air bag system, braking sys-
tem), power unit systems (engine sys-
tem, gearbox system) or steering system
blows, contact an authorized dealer.
Inboard Screw Location
155
General Information
The fuses protect electrical systems against
excessive current.
When a device does not work, you must check
the fuse element inside the blade fuse for a
break/melt.
Also, please be aware that when using power
outlets for extended periods of time with the
engine off may result in vehicle battery dis-
charge.
Totally Integrated Power Module
The Totally Integrated Power Module is lo-
cated in the engine compartment near the
battery. This center contains cartridge fuses,
mini fuses, and relays. A label that identifies
each component is printed on the inside of
the cover.
Cavity
Cartridge Fuse
Mini Fuse
Description
J1
J2
30 Amp Pink
Transfer Case Module
J3
J4
25 Amp Clear
Driver Door Node
J5
25 Amp Clear
Passenger Door Node
J6
40 Amp Green
Anti-Lock Brake System (ABS) Pump/Stability Control System
J7
30 Amp Pink
Anti-Lock Brake System (ABS) Valve/Stability Control System
J8
J9
40 Amp Green
PZEV Sec Motor/Flex Fuel – If Equipped
Totally Integrated Power Module
IN CASE OF EMERGENCY
156
Cavity
Cartridge Fuse
Mini Fuse
Description
J10
30 Amp Pink
Headlamp Wash Relay/Manifold Tuning Valve
J11
30 Amp Pink
Sway Bar
J12
J13
60 Amp Yellow
Ignition Off Draw (IOD) – Main
J14
40 Amp Green
Rear Defroster
J15
40 Amp Green
Front Blower
J17
40 Amp Green
Starter Solenoid
J18
20 Amp Blue
Powertrain Control Module (PCM) Trans Range
J19
60 Amp Yellow
Radiator Fan
J20
30 Amp Pink
Front Wiper LO/HI
J21
20 Amp Blue
Front/Rear Washer
J22
Spare
M1
15 Amp Blue
Center High-Mounted Stop Light (CHMSL)/Switch Stop Lamp Feed
M2
20 Amp Yellow
Relay Trailer Lighting (Stop lamp)
M3
20 Amp Yellow
Front/Rear Axle Locker Relay
M4
2 Amp Grey
Clock Spring
M5
25 Amp Clear
Power Inverter – If Equipped
M6
20 Amp Yellow
Power Outlet #1/Rain Sensor
M7
20 Amp Yellow
Power Outlet #2 (BATT/ACC SELECT)
M8
20 Amp Yellow
Front Heated Seat
M9
20 Amp Yellow
Rear Heated Seat – If Equipped
157
Cavity
Cartridge Fuse
Mini Fuse
Description
M10
15 Amp Blue
Ignition Off Draw – Vehicle Entertainment System, Satellite Digital Au-
dio Receiver (SDARS), DVD, Hands-Free Module, RADIO, Antenna,
Universal Garage Door Opener, Vanity Lamp
M11
10 Amp Red
(Ignition Off Draw) Climate Control System, Underhood Lamp
M12
30 Amp Green
Amplifier
M13
20 Amp Yellow
Ignition Off Draw – Cabin Compartment Node, Wireless Control Module,
SIREN, Multifunction Control Switch
M14
20 Amp Yellow
Trailer Tow (Export Only)
M15
20 Amp Yellow
Climate Control System, Rear View Mirror, Cabin Compartment Node,
Transfer Case Switch, Multi-Function Control Switch, Tire Pressure
Monitor, Glow Plug Module – Export Diesel Only
M16
10 Amp Red
Airbag Module
M17
15 Amp Blue
Left Tail/License/Park Lamp
M18
15 Amp Blue
Right Tail/Park/Run Lamp
M19
25 Amp Clear
Auto Shut Down (ASD #1 and #2)
M20
15 Amp Blue
Cabin Compartment Node Interior Light, Switch Bank
M21
20 Amp Yellow
Auto Shut Down (ASD #3)
M22
10 Amp Red
Right Horn (HI/LOW)
M23
10 Amp Red
Left Horn (HI/LOW)
M24
25 Amp Clear
Rear Wiper
M25
20 Amp Yellow
Fuel Pump, Diesel Lift Pump – Export Only
M26
10 Amp Red
Power Window Switch, Driver Window Switch
M27
10 Amp Red
Ignition Switch Feed, Wireless Module
M28
10 Amp Red
Powertrain Control Module
IN CASE OF EMERGENCY
158
Cavity
Cartridge Fuse
Mini Fuse
Description
M29
10 Amp Red
Powertrain
M30
15 Amp Blue
Wiper Motor Frt, J1962 Diagnostic Feed
M31
20 Amp Yellow
Backup Lamps
M32
10 Amp Red
Airbag Controller, TT EUROPE
M33
10 Amp Red
Powertrain Controller
M34
10 Amp Red
Park Assist, Climate Control System, Headlamp Wash, Compass
M35
10 Amp Red
Heated Mirrors
M36
20 Amp Yellow
Power Outlet
M37
10 Amp Red
Anti-Lock Brake System, Electronic Stability Control, Stop Lamp
Switch, Fuel Pump Relay
M38
25 Amp Clear
Lock/Unlock Motors
CAUTION!
• When installing the Integrated Power
Module cover, it is important to ensure
the cover is properly positioned and fully
latched. Failure to do so may allow water
to get into the Integrated Power Module,
and possibly result in an electrical sys-
tem failure.
CAUTION!
• When replacing a blown fuse, it is impor-
tant to use only a fuse having the correct
amperage rating. The use of a fuse with a
rating other than indicated may result in
a dangerous electrical system overload.
If a properly rated fuse continues to
blow, it indicates a problem in the circuit
that must be corrected.
JACKING AND TIRE
CHANGING
WARNING!
• Do not attempt to change a tire on the
side of the vehicle close to moving traf-
fic. Pull far enough off the road to avoid
the danger of being hit when operating
the jack or changing the wheel.
159
ENGINE COMPARTMENT
3.6L Engine
1 — Integrated Power Module (Fuses)
7 — Washer Fluid Reservoir
2 — Battery
8 — Engine Coolant Reservoir
3 — Engine Oil Dipstick
9 — Air Cleaner Filter
4 — Automatic Transmission Dipstick (Under Engine Cover)
10 — Coolant Pressure Cap
5 — Engine Oil Fill
11 — Power Steering Fluid Reservoir
6 — Brake Fluid Reservoir
177
Temperature Grades
The Temperature grades are A (the high-
est), B, and C, representing the tire's
resistance to the generation of heat and
its ability to dissipate heat, when tested
under controlled conditions on a speci-
fied indoor laboratory test wheel.
Sustained high temperature can cause
the material of the tire to degenerate and
reduce tire life, and excessive tempera-
ture can lead to sudden tire failure. The
grade C corresponds to a level of perfor-
mance, which all passenger vehicle tires
must meet under the Federal Motor Ve-
hicle Safety Standard No. 109. Grades
B and A represent higher levels of per-
formance on the laboratory test wheel,
than the minimum required by law.
WARNING!
The temperature grade for this tire is
established for a tire that is properly
WARNING!
inflated and not overloaded. Exces-
sive speed, under-inflation, or ex-
cessive loading, either separately or
in
combination,
can
cause
heat
buildup and possible tire failure.
STORING THE VEHICLE
If you are leaving your vehicle dormant for
more than 21 days, you may want to take
steps to protect your battery. You may:
Remove Cartridge fuse #J13 in the Inte-
grated
Power
Module
(Fuses)
labeled
Ignition-Off Draw (IOD) and store it in a
safe location within the fuse box.
Or, disconnect the negative cable from the
battery.
Anytime you store your vehicle, or keep it out
of service (i.e., vacation) for two weeks or
more, run the air conditioning system at idle
for about five minutes in the fresh air and
high blower setting. This will ensure ad-
equate system lubrication to minimize the
possibility of compressor damage when the
system is started again.
BODYWORK
Body And Underbody Maintenance
Cleaning Headlights
Your vehicle is equipped with plastic head-
lights and fog lights that are lighter and less
susceptible to stone breakage than glass
headlights.
Plastic is not as scratch resistant as glass and
therefore different lens cleaning procedures
must be followed.
To minimize the possibility of scratching the
lenses and reducing light output, avoid wip-
ing with a dry cloth. To remove road dirt, wash
with a mild soap solution followed by rinsing.
Do not use abrasive cleaning components,
solvents, steel wool or other aggressive mate-
rial to clean the lenses.
207