Dodge Viper - 2016 Fuse Box Diagram

Dodge Viper - 2016 Fuse Box Diagram

NOTE:
Do not exceed the maximum power of 160 Watts
(13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power
rating is exceeded the fuse protecting the system will
need to be replaced.
WARNING!
To avoid serious injury or death:
Only devices designed for use in this type of outlet
should be inserted into any 12 Volt outlet.
Do not touch with wet hands.
Close the lid when not in use and while driving the
vehicle.
If this outlet is mishandled, it may cause an electric
shock and failure.
CAUTION!
Many accessories that can be plugged in draw
power from the vehicle’s battery, even when not in
use
(i.e.,
cellular
phones,
etc.).
Eventually,
if
plugged in long enough, the vehicle’s battery will
(Continued)
Center Console Outlet
136
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Connecting The Jumper Cables
1. Wear eye protection and remove any metal jewelry
such as watchbands or bracelets that might make an
inadvertent electrical contact.
2. When boost is provided by a battery in another
vehicle, park that vehicle within booster cable reach,
but without allowing the vehicles to touch one an-
other.
3. Set the parking brake, place the transmission in NEU-
TRAL, and turn the ignition OFF on both vehicles.
4. Turn off the heater, radio, and all unnecessary electri-
cal loads.
5. Remove the plastic fuse cover to gain access to the
remote jump-start positive
(+)
post in the engine
compartment. Refer to the following illustration for
remote jump-starting connections.
Remote Jump Start Connections
1 — Remote Positive (+) Post
2 — Remote Negative (-) Post
6
WHAT TO DO IN EMERGENCIES
329
Water may drain slowly from the ends of the wing after
washing or exposure to rain, this is normal. Opening the
liftgate will expedite drainage.
WARNING!
Use extra caution when closing the rear deck lid on a
vehicle equipped with a rear wing. Due to the added
weight of the rear wing the deck lid will close at a
higher rate of speed and can cause injury.
Carbon Fiber — If Equipped
The clear coated carbon fiber panels will have some
variation and minor waviness in the woven pattern. This
is inherent to the process and a sign of its authenticity.
All carbon fiber materials are susceptible to UV degra-
dation during long exposure to the sun. The woven
carbon components use the latest technology in the resin
system and the clear coat. As with any automotive
coating, storing your vehicle in a covered location will
guarantee a long lasting finish.
The rear wing is molded with unidirectional carbon fiber
and painted in body color. Some patterned or linear
conditions may be visible in the painted carbon fiber
surfaces. This is also a normal result of the carbon fiber
process.
FUSES
WARNING!
When replacing a blown fuse, always use an ap-
propriate replacement fuse with the same amp
rating as the original fuse. Never replace a fuse
with another fuse of higher amp rating. Never
replace a blown fuse with metal wires or any other
(Continued)
370
MAINTAINING YOUR VEHICLE
WARNING!
(Continued)
material. Failure to use proper fuses may result in
serious personal injury, fire and/or property dam-
age.
Before replacing a fuse, make sure that the ignition
is off and that all the other services are switched off
and/or disengaged.
If the replaced fuse blows again, contact an autho-
rized dealer.
If a general protection fuse for safety systems (air
bag system, braking system), power unit systems
(engine system, gearbox system) or steering system
blows, contact an authorized dealer.
Power Distribution Center
The Power Distribution Center is located in the engine
compartment on the driver’s side of the vehicle. This
center contains fuses and relays.
Power Distribution Center
7
MAINTAINING YOUR VEHICLE
371
Cavity
Relay
Cartridge
Fuse
Mini-Fuse
Description
3
40 Amp
Green
Rad Fan
4
40 Amp
Green
Rad Fan Rly High
5
40 Amp
Green
ABS/ESP Pump Feed
6
40 Amp
Green
Starter
7
40 Amp
Green
CBC (Ext. Lighting #1)
8
40 Amp
Green
CBC (Ext. Lighting #2)
9
30 Amp Pink
CBC (Lighting, Washer Pump)
10
30 Amp Pink
CBC (Power Lock)
11
Jumper Black
B+ Jumper
372
MAINTAINING YOUR VEHICLE
Cavity
Relay
Cartridge
Fuse
Mini-Fuse
Description
12
25 Amp
Clear
ABS/ESP Valve Feed
13
20 Amp Yel-
low
Horn
14
10 Amp Red
A/C Clutch
15
10 Amp Red
Diagnostic, Fuel Door, Stop Switch
16
15 Amp Blue
KIN, RF Hub
17
25 Amp cir-
cuit breaker
Power Seats
18
30 Amp Pink
Driver Door Mod
19
30 Amp Pink
Passenger Door Mod
20
30 Amp Pink
Rear Window Defroster
21
20 Amp Blue
Wiper
22
Jumper Black
B+ Jumper
7
MAINTAINING YOUR VEHICLE
373
Cavity
Relay
Cartridge
Fuse
Mini-Fuse
Description
23
15 Amp Blue
HVAC MOD, Cluster, ICS-Switch Bank
24
25 Amp
Clear
PCM-Powertrain Control Module
25
25 Amp
Clear
Fuel Pump
26
20 Amp Yel-
low
ASD #1
27
20 Amp Yel-
low
ASD #2
28
Spare
29
40 Amp
Green
HVAC Blower
30
20 Amp Yel-
low
RR Power Outlet, Adj. Pedals, UCI
31
Jumper Black
B+ Jumper
374
MAINTAINING YOUR VEHICLE
Cavity
Relay
Cartridge
Fuse
Mini-Fuse
Description
32
Spare
33
20 Amp Blue
Run Acc relay
34
Jumper Black
B+ Jumper
35
Spare
36
10 Amp Red
ORC Mod Run
37
15 Amp Blue
Cluster, Camera
38
20 Amp Yel-
low
Active Damping Suspension
39
10 Amp Red
HVAC Module, In Vehicle Temp, Blower Relay
40
Spare
41
G8VA
Run/Start
42
G8VA
Fuel Door
7
MAINTAINING YOUR VEHICLE
375
Cavity
Relay
Cartridge
Fuse
Mini-Fuse
Description
43AC (For-
ward
Fuse)
2 Amp Grey
SCCM
43BE
(Rearward
Fuse)
10 Amp Red
Corax
44AC (For-
ward
Fuse)
10 Amp Red
Rear View Mirror, Aux Port Jumper.
44BE
(Rearward
Fuse)
10 Amp Red
IBS
45
10 Amp Red
PCM-Powertrain Control Module, Fuel Pump Relay.
46
10 Amp Red
ESC Module, Stop Lamp Switch
47
10 Amp Red
ORC Module, Passenger Seat OCM
376
MAINTAINING YOUR VEHICLE
Cavity
Relay
Cartridge
Fuse
Mini-Fuse
Description
48
10 Amp Red
SCCM
49
25 Amp
Clear
Amplifier
50
HC Micro
Rad Fan
51
HC Micro
Rad Fan Relay SER/PAR
52
HC Micro
Starter Relay
53
HC Micro
Rear Window Defroster Relay
54
HC Relay
Rad Fan Relay High
55
HC Micro
Wiper ON/OFF
56
HC Micro
Wiper LO/HI
57
G8VA
Horn Relay
58
G8VA
A/C Clutch Relay
59
HC Micro
HVAC Blower
60
HC Micro
Fuel Pump
7
MAINTAINING YOUR VEHICLE
377
Cavity
Relay
Cartridge
Fuse
Mini-Fuse
Description
61
G8VA
Run Relay #1
62
G8VA
Run Relay #2
63
HC Micro
ASD #1
64
HC Micro
ASD #2
65
G8VA
Run Accy #1, Pop Up, Driver Door Window Switch
66
Spare
NOTE:
A 15 Amp fuse for the radio system is located
in-line at the battery positive terminal.
CAUTION!
When
installing
the
power
distribution
center
cover, it is important to ensure the cover is properly
positioned and fully latched. Failure to do so may
(Continued)
CAUTION!
(Continued)
allow water to get into the power distribution
center and possibly result in an electrical system
failure.
When replacing a blown fuse, it is important to use
only a fuse having the correct amperage rating. The
use of a fuse with a rating other than indicated may
(Continued)
378
MAINTAINING YOUR VEHICLE
CAUTION!
(Continued)
result in a dangerous electrical system overload. If
a properly rated fuse continues to blow, it indicates
a problem in the circuit that must be corrected.
VEHICLE STORAGE
We recommend that you follow these guidelines for
storing your vehicle for extended periods.
Fill the fuel tank. This will prevent water condensation
inside the tank. If you plan to store your vehicle more
than two months, add an anti-oxidant fuel stabilizer to
the fuel tank.
Change the oil to remove any corrosive combustion
related acids in the crankcase.
Check that the radiator coolant level of protection is to
at least -20°F (-29°C).
Make sure that all tires are inflated to the optimum
pressure.
Wash and wax the vehicle to protect the finish.
Store the vehicle in a dry, well-ventilated location.
Move the wiper blades away from the windshield.
Block the wheels. Do not apply the parking brake.
Cut blocks of plywood about the same size of the tires.
Cover each block with indoor/outdoor carpeting and
place them between the tires and concrete. This will
prevent tire flat spotting.
For long-term storage, remove the tires and put the
vehicle up on blocks. Stack the tires on plywood and
cover with a tarp to prevent flat spotting.
If the vehicle will be subjected to freezing tempera-
tures, either remove the battery and store it in a dry,
well
ventilated
area
or
connect
a
trickle
charger
7
MAINTAINING YOUR VEHICLE
379
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.
The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.
The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.
Rear area of the center console.
NOTE:
Do not exceed the maximum power of
160 Watt (13 Amp) at 12 Volts. If the
160 Watt (13 Amp) power rating is ex-
ceeded, the fuse protecting the system
will need to be replaced.
Power outlets are designed for accessory
plugs only. Do not insert any other object
in the power outlet as this will damage
the outlet and blow the fuse. Improper
use of the power outlet can cause dam-
age not covered by your new vehicle
limited warranty.
Rear 12V Power Outlet
ELECTRONICS
109
NOTE:
The battery is located underneath an access panel inside the rear compartment on the left
side of the vehicle. A remote battery terminal is located in the engine compartment for
jump-starting.
Connecting The Jumper Cables
1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets
that might make an inadvertent electrical contact.
2. When boost is provided by a battery in another vehicle, park that vehicle within booster
cable reach, but without allowing the vehicles to touch one another.
3. Set the parking brake, place the transmission in NEUTRAL, and turn the ignition OFF
on both vehicles.
4. Turn off the heater, radio, and all unnecessary electrical loads.
5. Remove the plastic fuse cover to gain access to the remote jump-start positive
(+)
post
in the engine compartment. Refer to the following illustration for remote jump-starting
connections.
CAUTION!
Failure to follow these procedures could result in damage to the charging system of the
booster vehicle or the discharged vehicle.
6. Connect the positive
(+)
end of the jumper cable to the remote positive
(+)
post of the
discharged vehicle.
7. Connect the opposite end of the positive
(+)
jumper cable to the positive
(+)
post of the
booster battery.
Jump Starting Locations
1 — Remote Negative Post
2 — Remote Positive Post
WHAT TO DO IN EMERGENCIES
123
5. Power Distribution Center (Fuses)
6. Power Steering Fluid Reservoir
7. Air Cleaner Filter
8. Engine Oil Dipstick
9. Engine Coolant Reservoir Cap
MAINTAINING YOUR VEHICLE
129
FUSES
Power Distribution Center
The Power Distribution Center is located in the engine compartment on the driver's side
of the vehicle. This center contains fuses and relays.
Cavity
Relay
Cartridge Fuse
Mini-Fuse
Description
3
40 Amp Green
Rad Fan
4
40 Amp Green
Rad Fan Rly High
5
40 Amp Green
ABS/ESP Pump Feed
6
40 Amp Green
Starter
7
40 Amp Green
CBC (Ext. Lighting #1)
8
40 Amp Green
CBC (Ext. Lighting #2)
9
30 Amp Pink
CBC (Lighting, Washer
Pump)
10
30 Amp Pink
CBC (Power Lock)
11
Jumper Black
B+ Jumper
12
25 Amp Clear
ABS/ESP Valve Feed
13
20 Amp Yellow
Horn
14
10 Amp Red
A/C Clutch
15
10 Amp Red
Diagnostic, Fuel Door,
Stop Switch
16
15 Amp Blue
KIN, RF Hub
17
25 Amp circuit
breaker
Power Seats
18
30 Amp Pink
Driver Door Mod
19
30 Amp Pink
Passenger Door Mod
20
30 Amp Pink
Rear Window Defroster
21
20 Amp Blue
Wiper
22
Jumper Black
B+ Jumper
23
15 Amp Blue
HVAC MOD, Cluster, ICS-
Switch Bank
24
25 Amp Clear
PCM-Powertrain Control
Module
25
25 Amp Clear
Fuel Pump
26
20 Amp Yellow
ASD #1
27
20 Amp Yellow
ASD #2
28
Spare
29
40 Amp Green
HVAC Blower
30
20 Amp Blue
RR Power Outlet, Adj.
Pedals, UCI
31
Jumper Black
B+ Jumper
MAINTAINING YOUR VEHICLE
136
Cavity
Relay
Cartridge Fuse
Mini-Fuse
Description
32
Spare
33
20 Amp Blue
Run Acc relay
34
Jumper Black
B+ Jumper
35
Spare
36
10 Amp Red
ORC Mod Run
37
15 Amp Blue
Cluster, Camera
38
20 Amp Yellow
Active Damping Suspen-
sion
39
10 Amp Red
HVAC Module, In Vehicle
Temp, Blower Relay
40
Spare
41
G8VA
Run/Start
42
G8VA
Fuel Door
43AC
(Forward
Fuse)
2 Amp Grey
SCCM
43BE
(Rearward
Fuse)
10 Amp Red
Corax
44AC
(Forward
Fuse)
10 Amp Red
Rear View Mirror, Aux Port
Jumper.
44BE
(Rearward
Fuse)
10 Amp Red
IBS
45
10 Amp Red
PCM-Powertrain Control
Module, Fuel Pump Relay.
46
10 Amp Red
ESC Module, Stop Lamp
Switch
47
10 Amp Red
ORC Module, Passenger
Seat OCM
48
10 Amp Red
SCCM
49
25 Amp Clear
Amplifier
50
HC Micro
Rad Fan
51
HC Micro
Rad Fan Relay SER/PAR
52
HC Micro
Starter Relay
53
HC Micro
Rear Window Defroster
Relay
54
HC Relay
Rad Fan Relay High
55
HC Micro
Wiper ON/OFF
56
HC Micro
Wiper LO/HI
57
G8VA
Horn Relay
MAINTAINING YOUR VEHICLE
137
Cavity
Relay
Cartridge Fuse
Mini-Fuse
Description
58
G8VA
A/C Clutch Relay
59
HC Micro
HVAC Blower
60
HC Micro
Fuel Pump
61
G8VA
Run Relay #1
62
G8VA
Run Relay #2
63
HC Micro
ASD #1
64
HC Micro
ASD #2
65
G8VA
Run Accy #1, Pop Up,
Driver Door Window
Switch
66
Spare
NOTE:
A 15 Amp fuse for the radio system is located in-line at the battery positive terminal.
CAUTION!
• When installing the power distribution center cover, it is important to ensure the
cover is properly positioned and fully latched. Failure to do so may allow water to get
into the power distribution center and possibly result in an electrical system failure.
• When replacing a blown fuse, it is important to use only a fuse having the correct
amperage rating. The use of a fuse with a rating other than indicated may result in a
dangerous electrical system overload. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be corrected.
TIRES — GENERAL INFORMATION
SUMMER/THREE-SEASON TIRES
This vehicle may be equipped with wheels and tires to enhance traction in both wet and
dry conditions.
Summer tires are not intended to be driven in snow or on ice.
Summer tires have significantly reduced grip in temperatures below 50°F (10°C).
Use Summer tires only in sets of four.
NOTE:
Summer tires will not contain the all season designation or mountain/snowflake symbol on
the sidewall of the tire.
MAINTAINING YOUR VEHICLE
138
FREQUENTLY ASKED QUESTIONS
GETTING STARTED
How do I adjust my foot rest? pg. 28
How do I adjust my pedals? pg. 27
OPERATING YOUR VEHICLE
How does my speed control work? pg. 32
ELECTRONICS
Which radio is in my vehicle?
Uconnect 8.4AN pg. 61
How do I activate the Audio Jack?
Uconnect 8.4AN pg. 68
How do I set the clock on my radio?
Uconnect 8.4AN pg. 61
How do I pair my cell phone via Bluetooth with the Uconnect Hands-Free Voice
Activation System? pg. 94
How do I use my USB port to listen to audio through my touch-screen radio? pg. 68
How do I configure my Universal Garage Door Opener (HomeLink)? pg. 106
UTILITY
How do I know how much I can tow with my Viper? pg. 110
WHAT TO DO IN EMERGENCIES
What do I do if my TPMS warning light is blinking? pg. 112
How do I Jump-Start my vehicle? pg. 122
MAINTAINING YOUR VEHICLE
Where is my Fuse Block located? pg. 136
What type of oil do I use? pg. 130
How often should I change my engine’s oil? pg. 133
What should my tire pressure be set at? pg. 139
FREQUENTLY ASKED QUESTIONS
147