Dodge Avenger - 2014 Fuse Box Diagram

Dodge Avenger - 2014 Fuse Box Diagram

WARNING!
(Continued)
way (including removal or loosening/tightening of
seat attachment bolts), take the vehicle to your
authorized dealer. Only manufacturer approved
seat accessories may be used. If it is necessary to
modify the air bag system for persons with dis-
abilities, contact your authorized dealer.
Air Bag Warning Light
You will want to have the air bags ready to
inflate for your protection in a collision. The
Air Bag Warning Light monitors the internal
circuits and interconnecting wiring associated
with air bag system electrical components. While the air
bag system is designed to be maintenance free, if any of
the following occurs, have an authorized dealer service
the air bag system immediately.
The Air Bag Warning Light does not come on during
the four to eight seconds when the ignition switch is
first turned to the ON/RUN position.
The Air Bag Warning Light remains on after the four to
eight second interval.
The Air Bag Warning Light comes on intermittently or
remains on while driving.
NOTE:
If the speedometer, tachometer, or any engine
related gauges are not working, the Occupant Restraint
Controller (ORC) may also be disabled. The air bags may
not be ready to inflate for your protection. Promptly
check the fuse block for blown fuses. Refer to the label
located on the inside of the fuse block cover for the
proper air bag fuses. See your authorized dealer if the
fuse is good.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
73
ELECTRICAL POWER OUTLETS
There are two 12 Volt (13 Amp) electrical power outlets
on this vehicle. Both of the power outlets are protected by
a fuse.
The instrument panel power outlet, located below the
climate control knobs, has power available only when the
ignition is ON. This power outlet will also operate a
conventional cigar lighter unit.
NOTE:
To preserve the heating element, do not hold the
lighter in the heating position.
Instrument Panel Power Outlet
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
199
A second power outlet is located inside the center con-
sole.
The center console power outlet is powered directly from
the battery (power available at all times). Items plugged
into this power outlet may discharge the battery and/or
prevent the engine from starting.
NOTE:
To ensure proper operation a MOPAR® knob
and element must be used.
CAUTION!
Do not exceed the maximum power of 160 Watts
(13 Amps) at 12 Volts. If the 160 Watt (13 Amp)
power rating is exceeded the fuse protecting the
system will need to be replaced.
Power outlets are designed for accessory plugs
only. Do not insert any other object in the power
outlets as this will damage the outlet and blow the
fuse. Improper use of the power outlet can cause
damage not covered by your New Vehicle Limited
Warranty.
Center Console Power Outlet
200
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
To avoid serious injury or death:
Only devices designed for use in this type of outlet
should be inserted into any 12 Volt outlet.
Do not touch with wet hands.
Close the lid when not in use and while driving the
vehicle.
If this outlet is mishandled, it may cause an electric
shock and failure.
Power Outlet Fuse Locations
1 — #16 Fuse 15 A Blue Cigar Lighter Instrument Panel
2 — #11 Fuse 15 A Blue Power Outlet Inside Arm Rest
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
201
After Starting
The idle speed is controlled automatically and it will
decrease as the engine warms up.
ENGINE BLOCK HEATER — IF EQUIPPED
The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a
standard
110-115
Volt
AC
electrical
outlet
with
a
grounded, three-wire extension cord.
The engine block heater must be plugged in at least one
hour to have an adequate warning effect on the engine.
The engine block heater cord is bundled under the hood
between the headlight assembly and the Totally Inte-
grated Power Module (Fuse Box) on the driver’s side of
the vehicle.
WARNING!
Remember to disconnect the engine block heater
cord before driving. Damage to the 110-115 Volt
electrical cord could cause electrocution.
AUTOMATIC TRANSMISSION
CAUTION!
Damage to the transmission may occur if the follow-
ing precautions are not observed:
Shift into PARK only after the vehicle has come to
a complete stop.
Shift into or out of REVERSE only after the vehicle
has come to a complete stop and the engine is at
idle speed.
(Continued)
5
STARTING AND OPERATING
305
ENGINE COMPARTMENT — 2.4L
1 — Engine Coolant Reservoir
5 — Integrated Power Module (Fuses)
9 — Coolant Pressure Cap
2 — Power Steering Fluid Reservoir
6 — Power Distribution Center (Fuses)
10 — Engine Oil Dipstick
3 — Automatic Transmission Dipstick
7 — Air Cleaner Filter
11 — Washer Fluid Reservoir
4 — Brake Fluid Reservoir
8 — Engine Oil Fill
7
MAINTAINING YOUR VEHICLE
429
ENGINE COMPARTMENT — 3.6L
1 — Engine Coolant Reservoir
5 — Air Cleaner Filter
2 — Power Steering Fluid Reservoir
6 — Engine Oil Dipstick
3 — Brake Fluid Reservoir
7 — Engine Oil Fill
4 — Integrated Power Module (Fuses)
8 — Washer Fluid Reservoir
430
MAINTAINING YOUR VEHICLE
Installation
Align the liner in the cupholder and press down firmly.
FUSES
WARNING!
When replacing a blown fuse, always use an ap-
propriate replacement fuse with the same amp
rating as the original fuse. Never replace a fuse
with another fuse of higher amp rating. Never
replace a blown fuse with metal wires or any other
material. Failure to use proper fuses may result in
serious personal injury, fire and/or property dam-
age.
Before replacing a fuse, make sure that the ignition
is off and that all the other services are switched off
and/or disengaged.
(Continued)
WARNING!
(Continued)
If the replaced fuse blows again, contact an autho-
rized dealer.
If a general protection fuse for safety systems (air
bag system, braking system), power unit systems
(engine system, gearbox system) or steering system
blows, contact an authorized dealer.
7
MAINTAINING YOUR VEHICLE
467
Integrated Power Module
The Integrated Power Module is located in the engine
compartment near the air cleaner assembly. This center
contains cartridge fuses and mini fuses. A label that
identifies each component may be printed on the inside
of the cover. Refer to the graphic below for FUSES/TIPM
location.
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
1
40 Amp
Green
Power Top Module
– If Equipped
Integrated Power Module
468
MAINTAINING YOUR VEHICLE
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
2
20 Amp
Yellow
Brake Vacuum
Pump
3
10 Amp
Red
Center High
Mounted Stop
Light (CHMSL)/
Brake Switch
4
10 Amp
Red
Ignition Switch
5
20 Amp
Yellow
Trailer Tow – If
Equipped
6
10 Amp
Red
Power Mirror
Switch/Climate
Controls
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
7
30 Amp
Green
Ignition Off Draw
(IOD) Sense 1
8
30 Amp
Green
Ignition Off Draw
(IOD) Sense 2
9
40 Amp
Green
Battery Feed –
Power Seats – If
Equipped
10
20 Amp
Yellow
Instrument Panel/
Power Locks/
Interior Lights
11
15 Amp
Lt Blue
Selectable Power
Outlet (Inside Cen-
ter Arm Rest)
7
MAINTAINING YOUR VEHICLE
469
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
12
20 Amp
Yellow
Spare
13
20 Amp
Yellow
Ignition/Cigar
Lighter
14
10 Amp
Red
Instrument Panel
15
40 Amp
Green
Radiator Fan Relay
16
15 Amp
Lt. Blue
Sunroof – If
Equipped
17
10 Amp
Red
Wireless Control
Module (WCM)/
Clock/Steering Con-
trol Module (SCM)
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
18
40 Amp
Green
Auto Shutdown
(ASD) Relay
19
20 Amp
Yellow
Audio Amplifier –
If Equipped
20
15 Amp
Lt. Blue
Radio
21
10 Amp
Red
Siren – If Equipped
22
10 Amp
Red
Ignition Run – Cli-
mate Controls/Hot
Cupholder – If
Equipped
23
15 Amp
Lt. Blue
Auto Shutdown
(ASD) Relay 3
470
MAINTAINING YOUR VEHICLE
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
24
25 Amp
Natural
Sunroof – If
Equipped
25
10 Amp
Red
Ignition Run —
Heated Mirrors - If
Equipped
26
15 Amp
Lt. Blue
Auto Shutdown
(ASD) Relay 2
27
10 Amp
Red
Ignition Run – Oc-
cupant Classifica-
tion Module
(OCM)/Occupant
Restraint Controller
(ORC)
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
28
10 Amp
Red
Ignition Run —
Occupant Classifi-
cation Module
(OCM)/Occupant
Restraint Controller
(ORC)
29
Hot Car (No Fuse
Required)
30
20 Amp
Yellow
Ignition Run –
Heated Seats – If
Equipped
31
Spare
32
30 Amp
Pink
Auto Shutdown
(ASD) Relay 1
7
MAINTAINING YOUR VEHICLE
471
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
33
10 Amp
Red
Switch Bank/
Diagnostic Link
Connector/
Powertrain Control
Module (PCM)
34
30 Amp
Pink
Anti-Lock Brakes
(ABS) Module – If
Equipped/
Electronic Stability
Control (ESC)
Module – If
Equipped
35
40 Amp
Green
Anti-Lock Brakes
(ABS) Module – If
Equipped/
Cavity
Car-
tridge
Fuse
Mini
Fuse
Description
Electronic Stability
Control (ESC)
Module – If
Equipped
36
30 Amp
Pink
Passenger Door
Module (PDM)/
Driver Door Mod-
ule (DDM)
37
25 Amp
Natural
Power Top Module
– If Equipped
472
MAINTAINING YOUR VEHICLE
CAUTION!
When
installing
the
Integrated
Power
Module
cover, it is important to ensure the cover is properly
positioned and fully latched. Failure to do so may
allow water to get into the Integrated Power Mod-
ule, and possibly result in an electrical system
failure.
When replacing a blown fuse, it is important to use
only a fuse having the correct amperage rating. The
use of a fuse with a rating other than indicated may
result in a dangerous electrical system overload. If
a properly rated fuse continues to blow, it indicates
a problem in the circuit that must be corrected.
VEHICLE STORAGE
If you will not be using your vehicle for more than 21
days, you may want to take steps to preserve your
battery.
Disengage the mini-fuse in the Power Distribution
Center labeled IOD (Ignition Off-Draw).
Or disconnect the negative cable from the battery.
Anytime you store your vehicle, or keep it out of
service (i.e., vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
in the fresh air and high blower setting. This will
ensure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
7
MAINTAINING YOUR VEHICLE
473
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.
The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.
The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.
POWER OUTLET
There are two 12 Volt electrical outlets on
this vehicle.
The instrument panel power outlet, lo-
cated below the climate control knobs,
has power available only when the igni-
tion is ON. This power outlet will also op-
erate a conventional cigar lighter unit.
Thereisalsoapoweroutletlocatedonthe
inside of the center console. This power
outlet is powered directly from the battery
(power
available
at
all
times).
Items
plugged into this power outlet may dis-
charge the battery and/or prevent the engine from starting.
NOTE:
Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt
(13 Amp) power rating is exceeded, the fuse protecting the system will need to be
replaced.
Power outlets are designed for accessory plugs only. Do not insert any other object in the
power outlet as this will damage the outlet and blow the fuse. Improper use of the power
outlet can cause damage not covered by your new vehicle warranty.
ELECTRONICS
73
FUSES
Integrated Power Module (fuses)
The Integrated Power Module (fuses) is located in the engine compartment near the air
cleaner assembly. This center contains cartridge fuses and mini fuses.
Cavity
Cartridge Fuse
Mini Fuse
Description
1
40 Amp Green
Power Top Module – If Equipped
2
20 Amp Yellow
Brake Vacuum Pump
3
10 Amp Red
Center High Mounted Stop Light
(CHMSL)/Brake Switch
4
10 Amp Red
Ignition Switch
5
20 Amp Yellow
Trailer Tow – If Equipped
6
10 Amp Red
Power Mirror Switch/Climate Con-
trols
7
30 Amp Green
Ignition Off Draw (IOD) Sense 1
8
30 Amp Green
Ignition Off Draw (IOD) Sense 2
9
40 Amp Green
Battery Feed – Power Seats – If
Equipped
10
20 Amp Yellow
Instrument Panel/Power Locks/
Interior Lights
11
15 Amp Lt Blue
Selectable Power Outlet (Inside
Center Arm Rest)
12
20 Amp Yellow
Spare
13
20 Amp Yellow
Ignition/Cigar Lighter
14
10 Amp Red
Instrument Panel
15
40 Amp Green
Radiator Fan Relay
16
15 Amp Lt. Blue
Sunroof – If Equipped
MAINTAINING YOUR VEHICLE
104
Cavity
Cartridge Fuse
Mini Fuse
Description
17
10 Amp Red
Wireless Control Module (WCM)/
Clock/Steering Control Module
(SCM)
18
40 Amp Green
Auto Shutdown (ASD) Relay
19
20 Amp Yellow
Audio Amplifier – If Equipped
20
15 Amp Lt. Blue
Radio
21
10 Amp Red
Siren – If Equipped
22
10 Amp Red
Ignition Run – Climate Controls/
Hot Cupholder – If Equipped
23
15 Amp Lt. Blue
Auto Shutdown (ASD) Relay 3
24
25 Amp Natural
Sunroof – If Equipped
25
10 Amp Red
Ignition Run — Heated Mirrors - If
Equipped
26
15 Amp Lt. Blue
Auto Shutdown (ASD) Relay 2
27
10 Amp Red
Ignition Run – Occupant Classifi-
cation Module (OCM)/Occupant
Restraint Controller (ORC)
28
10 Amp Red
Ignition Run — Occupant Classifi-
cation Module (OCM)/Occupant
Restraint Controller (ORC)
29
Hot Car (No Fuse Required)
30
20 Amp Yellow
Ignition Run – Heated Seats – If
Equipped
31
Spare
32
30 Amp Pink
Auto Shutdown (ASD) Relay 1
33
10 Amp Red
Switch Bank/Diagnostic Link
Connector/Powertrain Control
Module (PCM)
34
30 Amp Pink
Anti-Lock Brakes (ABS) Module – If
Equipped/Electronic Stability Con-
trol (ESC) Module – If Equipped
35
40 Amp Green
Anti-Lock Brakes (ABS) Module – If
Equipped/Electronic Stability Con-
trol (ESC) Module – If Equipped
36
30 Amp Pink
Passenger Door Module (PDM)/
Driver Door Module (DDM)
37
25 Amp Natural
Power Top Module – If Equipped
MAINTAINING YOUR VEHICLE
105
CAUTION!
• When installing the Integrated Power Module cover, it is important to ensure the cover
is properly positioned and fully latched. Failure to do so may allow water to get into the
Integrated Power Module, and possibly result in an electrical system failure.
• When replacing a blown fuse, it is important to use only a fuse having the correct
amperage rating. The use of a fuse with a rating other than indicated may result in a
dangerous electrical system overload. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be corrected.
TIRE PRESSURES
Check the inflation pressure of each tire, including the spare tire, at least monthly and
inflate to the recommended pressure for your vehicle.
The tire pressures recommended for your vehicle are found on the “Tire and Loading
Information” label located on the driver’s side door opening.
NOTE:
Refer to the Owner's Manual on the DVD for
more information regarding tire warnings
and instructions.
WARNING!
• Overloading of your tires is dangerous. Overloading can cause tire failure, affect
vehicle handling, and increase your stopping distance. Use tires of the recommended
load capacity for your vehicle. Never overload them.
• Improperly inflated tires are dangerous and can cause collisions. Under-inflation is
the leading cause of tire failure and may result in severe cracking, component sepa-
ration, or “blow out”. Over-inflation reduces a tire’s ability to cushion shock. Objects on
the road and chuck holes can cause damage that results in tire failure. Unequal tire
pressures can cause steering problems. You could lose control of your vehicle. Over-
inflated or under-inflated tires can affect vehicle handling and can fail suddenly,
resulting in loss of vehicle control.
MAINTAINING YOUR VEHICLE
106
UTILITY
How do I know how much I can tow with my Dodge Avenger? pg. 74
WHAT TO DO IN EMERGENCIES
What do I do if my TPMS warning light is blinking? pg. 76
How do I change a flat tire? pg. 81
How do I Jump-Start my vehicle? pg. 87
MAINTAINING YOUR VEHICLE
Where is my Fuse Block located? pg. 104
What type of oil do I use? pg. 97
How often should I change my engine’s oil? pg. 99
What should my tire pressure be set at? pg. 106
FREQUENTLY ASKED QUESTIONS
113