Dodge Journey - 2009 Fuse Box Diagram

Dodge Journey - 2009 Fuse Box Diagram

Sunroof Fully Closed
Press the switch forward and release to ensure that the
sunroof is fully closed.
ELECTRICAL POWER OUTLETS
There are two fused 12-Volt power outlets located in the
center console below the radio. The outlet on the top has
power available when the ignition switch in the ON or
ACC position. The outlet on the bottom has power
available when the ignition switch is in the LOCK, ON, or
ACC position.
1 — Switched Power
2 — Battery Power
Front Power Outlets
174
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
A third fused 12-Volt power outlet is located on the back
of the center console. This outlet has power available
when the ignition switch is in the LOCK, ON or ACC
position.
A fourth fused 12-Volt power outlet is located on the left
quarter trim panel in the cargo area. This outlet has
power available when the ignition switch is in the ON or
ACC position.
Rear Power Outlet
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
175
3
15. Odometer/Trip Odometer
The odometer shows the total distance the vehicle has
been driven. The trip odometer shows individual trip
mileage. Refer to “Trip Odometer button” for additional
information.
NOTE:
U.S. Federal regulations require upon transfer of
vehicle ownership, the seller certify the mileage the
vehicle
has
been
driven.
Therefore,
if
the
odometer
reading is changed because of repair or replacement, be
sure to keep a record of the reading before and after the
service so that the correct mileage can be determined.
Vehicle Warning Messages
When the appropriate conditions exist, messages such as
“hood” (hood ajar), “door” (door ajar), “gATE” (liftgate
ajar), “LoCOOL” (low engine coolant), “LoWASH” (low
washer fluid), “gASCAP” (fuel cap fault), “ESPOFF”
(ESP in partial off mode), “NoFUSE” (IOD fuse out),
“HotOIL” (2.4L engine oil temp too hot), or “CHANgE
OIL” will display in the odometer.
NOTE:
If the instrument cluster is equipped with the
optional Electronic Vehicle Information Center (EVIC),
then most warnings will display in the EVIC. (See page
221 for more information.)
Hot Oil — 2.4L Engine
Refer to “Engine Oil Overheating — 2.4L Engine Only”
under “If Your Engine Overheats” in Section 6.
Fuel Cap Fault Message
If the vehicle diagnostic system determines that the fuel
filler cap is loose, improperly installed, or damaged, the
word “gASCAP” will display in the odometer. If this
occurs, tighten the fuel filler cap until a “clicking” sound
is heard. Then press the TRIP ODOMETER button to turn
UNDERSTANDING YOUR INSTRUMENT PANEL
209
4
After Starting
The idle speed is controlled automatically and it will
decrease as the engine warms up.
ENGINE BLOCK HEATER — IF EQUIPPED
The
engine
block
heater
warms
engine
coolant
and
permits quicker starts in cold weather. Connect the cord
to a standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.
The engine block heater cord is bundled under the hood
between the headlight assembly and the Totally Inte-
grated Power Module (Fuse Box) on the driver’s side of
the vehicle.
WARNING!
Remember to disconnect the cord before driving.
Damage to the 110-115 Volt electrical cord could cause
electrocution.
AUTOMATIC TRANSAXLE
CAUTION!
Damage to the transaxle may occur if the following
precautions are not observed:
Shift into PARK only after the vehicle has come to
a complete stop.
Shift
into
or
out
of
REVERSE
only
after
the
vehicle has come to a complete stop and the engine
is at idle speed.
Do not shift from REVERSE, PARK, or NEUTRAL
into any forward gear when the engine is above
idle speed.
Before shifting into any gear, make sure your foot
is firmly on the brake pedal.
STARTING AND OPERATING
311
5
2.4L ENGINE COMPARTMENT
1 — Coolant Bottle
8 — Remote Jump-Start Positive Battery Post
2 — Engine Coolant Reservoir
9 — Remote Jump-Start Negative Post
3 — Power Steering Fluid
10 — Fuses (Totally Integrated Power Module [TIPM])
4 — Engine Oil Dipstick
11 — Air Cleaner Filter
5 — Engine Oil Fill
12 — Washer Fluid Bottle
6 — Automatic Transaxle Dipstick
13 — Engine Coolant Cap
7 — Power Steering Fluid Reservoir
418
MAINTAINING YOUR VEHICLE
2.7L ENGINE COMPARTMENT
1 — Coolant Bottle
7 — Brake Fluid Reservoir
2 — Coolant Pressure Cap
8 — Remote Jump-Start Positive Battery Post
3 — Power Steering Fluid
9 — Remote Jump-Start Negative Post
4 — Engine Oil Fill
10 — Fuses (Totally Integrated Power Module [TIPM])
5 — Engine Oil Dipstick
11 — Air Cleaner Filter
6 — Automatic Transaxle Dispstick
12 — Washer Fluid Bottle
MAINTAINING YOUR VEHICLE
419
7
3.5L ENGINE COMPARTMENT
1 — Coolant Bottle
7 — Remote Jump-Start Positive Battery Post
2 — Coolant Pressure Cap
8 — Remote Jump-Start Negative Post
3 — Power Steering Fluid
9 — Fuses (Totally Integrated Power Module [TIPM])
4 — Engine Oil Fill
10 — Air Cleaner Filter
5 — Engine Oil Dipstick
11 — Washer Fluid Bottle
6 — Brake Fluid Reservoir
420
MAINTAINING YOUR VEHICLE
Seat Belt Maintenance
Do not bleach, dye, or clean the belts with chemical
solvents or abrasive cleaners. This will weaken the fabric.
Sun damage can also weaken the fabric.
If the belts need cleaning, use a mild soap solution or
lukewarm water. Do not remove the belts from the car to
wash them.
Replace the belts if they appear frayed or worn or if the
buckles do not work properly.
Dry with a soft tissue.
Cleaning The Cupholders
Clean with a damp cloth or towel using a mild detergent.
FUSES (TOTALLY INTEGRATED POWER
MODULE)
The Totally Integrated Power Module (TIPM) is located
in the engine compartment near the air cleaner assembly.
This center contains fuses and relays.
Totally Integrated Power Module (TIPM)
MAINTAINING YOUR VEHICLE
457
7
CAUTION!
When installing the power module cover, it is
important to ensure the cover is properly posi-
tioned and fully latched. Failure to do so may
allow water to get into the TIPM, and possibly
result in an electrical system failure.
When replacing a blown fuse, it is important to
use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated
may result in a dangerous electrical system over-
load. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be
corrected.
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
J1
40 Amp
Green
Power Folding Seat
J2
30 Amp
Pink
Transfer Case Module
- if equipped
J3
30 Amp
Pink
Rear Door Module
J4
25 Amp
White
Driver Door Node
J5
25 Amp
White
Passenger Door Node
J6
40 Amp
Green
Anti-Lock Brake Sys-
tem (ABS) Pump/
Electronic Stability
Program (ESP)
458
MAINTAINING YOUR VEHICLE
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
J7
30 Amp
Pink
Anti-Lock Brake Sys-
tem (ABS) Valve/
Electronic Stability
Program (ESP)
J8
40 Amp
Green
Power Memory Seat -
if equipped
J9
40 Amp
Green
Flex Fuel/PZEV Mo-
tor - if equipped
J10
30 Amp
Pink
(If Equipped) Head-
lamp Washer Relay-
(BUX), Manual Tun-
ing Valve
J11
30 Amp
Pink
(If Equipped) Sway
Bar/Thatchum Secu-
rity (BUX)/Power
Sliding Door
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
J13
60 Amp
Yellow
Ignition Off Draw
(IOD) Main
J14
40 Amp
Green
Electric Back Light
(EBL)
J15
30 Amp
Pink
Rear Blower - if
equipped
J17
40 Amp
Green
Starter Solenoid
J18
20 Amp
Yellow
NGC (Powertrain
Control Module)/
Transmission Range
J19
60 Amp
Yellow
Radiator Fan Motor
J20
30 Amp
Pink
Front Windshield
Wiper Hi/Low
J21
20 Amp
Blue
Front/Rear Washer
MAINTAINING YOUR VEHICLE
459
7
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
J22
25 Amp
White
Sunroof Module - if
equipped
M1
15 Amp
Blue
Center High Mounted
Stop Light (CHMSL)
M2
20 Amp
Yellow
(If Equipped) Trailer
Lights
M3
20 Amp
Yellow
Front/Rear Axle
M4
10 Amp
Red
(If Equipped) Trailer
Tow
M5
25 Amp
Natural
Power Inverter - if
equipped
M6
20 Amp
Yellow
Power Outlet #1/
Accessory (ACC) Rain
Sensor
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
M7
20 Amp
Yellow
Power Outlet #2 (Bat-
tery or Accessory
(ACC) Selectable)
M8
20 Amp
Yellow
Front Heated Seats -
if equipped
M9
20 Amp
Yellow
(If Equipped) Rear
Heated Seats
460
MAINTAINING YOUR VEHICLE
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
M10
15 Amp
Blue
Vanity Lamps/
Hands-Free Module
(HFM) - if equipped,
Remote Display - if
equipped, Satellite
Digital Audio Re-
ceiver (SDARS) - if
equipped, Universal
Garage Door Opener
(UGDO) - if
equipped, Vanity
Light, Video Enter-
tainment System
(VES)™ - if equipped
M11
10 Amp
Red
Automatic Tempera-
ture Control (ATC) -
if equipped, Under-
hood Light
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
M12
30 Amp
Green
Radio, Amplifier
(AMP)
M13
20 Amp
Yellow
Cabin Compartment
Node (CCN), Multi-
function Switch/Siren
Module
M14
20 Amp
Yellow
(If Equipped) Trailer
Tow (BUX)
M15
20 Amp
Yellow
Auto Dim Rearview
Mirror - if equipped,
Infrared Sensor (IR) -
if equipped, Multi-
function Switch, Tire
Pressure Monitor Sys-
tem (TPMS) - if
equipped, Transfer
Case Module - if
equipped,
MAINTAINING YOUR VEHICLE
461
7
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
M16
10 Amp
Red
Occupant Restraint
Controller (ORC)/
Occupant Classifica-
tion Module (OCM)
M17
15 Amp
Blue
Left Park/Side
Marker/Running/Tail
Lights, License Lights
M18
15 Amp
Blue
Right Park/Side
Marker/Running/Tail
Lights
M19
25 Amp
Natural
Auto Shut Down
(ASD) #1 and #2
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
M20
15 Amp
Blue
Electronic Vehicle In-
formation Center
(EVIC) - if equipped,
Interior Lighting,
Steering Wheel
Switches - if
equipped, Switch
Bank
M21
20 Amp
Yellow
Auto Shut Down
(ASD) #3
M22
10 Amp
Red
Right Horn
M23
10 Amp
Red
Left Horn
M24
25 Amp
Natural
Rear Wiper
462
MAINTAINING YOUR VEHICLE
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
M25
20 Amp
Yellow
Fuel Pump/Diesel
Lift Pump
M26
10 Amp
Red
Power MIRRORS
Switch/Drivers Win-
dow Switch
M27
10 Amp
Red
Steering Column
Lock, Wireless Igni-
tion Node (WIN)
M28
10 Amp
Red
NGC (Powertrain
Control Module)/
Transmission Feed
(Batt)
M29
10 Amp
Red
Occupant Classifica-
tion Module (OCM)
M30
15 Amp
Blue
Rear Wiper Module
Module/Power Fold-
ing Mirror
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
M31
20 Amp
Yellow
Back-Up Lights
M32
10 Amp
Red
Occupant Restraint
Controller (ORC)
M33
10 Amp
Red
NGC (Powertrain
Control Module) Bat-
tery Feed
M34
10 Amp
Red
Power Assist Module,
HVAC Module, Head-
lamp Washers, Com-
pass Module - if
equipped, Flashlight -
if equipped
M35
10 Amp
Red
Heated Mirrors - if
equipped
M36
20 Amp
Yellow
Power Outlet #3
(Batt)
MAINTAINING YOUR VEHICLE
463
7
Cavity
Cartridge
Fuse
Mini-
Fuse
Description
M37
10 Amp
Red
Anti-Lock Brake Sys-
tem (ABS), Electronic
Stability Program
(ESP), STOP LIGHT
Switch
M38
25 Amp
Natural
Lock/Unlock Motors
K1
Ignition Run/
Accessory Relay
K2
Ignition Run Relay
K3
Starter Solenoid Relay
K4
Ignition Run/Start
Relay
K5
(NGC) Powertrain
Control Module Relay
K6
Electric Back Light
(EBL) Relay
K7
K8
K9
Rear Blower Relay
K10
ASD Relay (Feed for
M19 and M21)
K11
Radiator Fan Relay
Low Speed
VEHICLE STORAGE
If you will not be using your vehicle for more than 21
days you may want to take steps to preserve your battery.
You may:
Remove the IOD (Ignition Off-Draw) mini-fuses from
the Totally Integrated Power Module located in the
engine compartment.
Or, disconnect the batter negative cable.
464
MAINTAINING YOUR VEHICLE
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.
The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.
The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.