Lincoln Navigator - 2008 Fuse Box Diagram

Lincoln Navigator - 2008 Fuse Box Diagram

CLOCK
Press the right (+) control to move
the time display forwards.
Press the left (-) control to move
the time display backwards.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
An auxiliary power point is located
by the passenger’s ankle near the
floor in the front console bin.
Do not use the power point for
operating the cigarette lighter
element (if equipped).
To prevent the fuse from being
blown, do not use the power
point(s) over the vehicle capacity of
12 VDC/180W. If the power point or
cigar lighter socket is not working, a fuse may have blown. Refer to
Fuses and relays
in the
Roadside Emergencies
chapter for information
on checking and replacing fuses.
To prevent the battery from being discharged, do not use the power
point longer than necessary when the engine is not running.
Always keep the power point caps closed when not being used.
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
88
Never place your arm over the airbag module as a deploying
airbag can result in serious arm fractures or other injuries.
To properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.
Do not put anything on or over the airbag module. Placing
objects on or over the airbag inflation area may cause those
objects to be propelled by the airbag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the airbag
supplemental restraint systems or its fuses. See your authorized
dealer.
The front passenger airbag is not designed to offer protection to
an occupant in the center front seating position.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the airbag system, increasing the
risk of injury. Do not modify the front end of the vehicle.
Additional equipment may affect the performance of the airbag
sensors increasing the risk of injury. Please refer to the
Body
Builders Layout Book
for instructions about the appropriate
installation of additional equipment.
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
172
impact sensors, the system wiring, the airbag system readiness light, the
airbag back up power and the airbag ignitors).
Determining if the system is operational
The SRS uses a readiness light in the instrument cluster or a tone to
indicate the condition of the system. Refer to
Airbag readiness
section
in the
Instrument Cluster
chapter. Routine maintenance of the airbag is
not required.
A difficulty with the system is indicated by one or more of the following:
The readiness light will either
flash or stay lit.
The readiness light will not
illuminate immediately after ignition is turned on.
A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and/or light are repaired.
If any of these things happen, even intermittently, have the SRS serviced
at an authorized dealer immediately. Unless serviced, the system may not
function properly in the event of a collision.
Seat-mounted side airbag system
Do not place objects or mount equipment on or near the airbag
cover on the side of the seatbacks of the front seats or in front
seat areas that may come into contact with a deploying airbag. Failure
to follow these instructions may increase the risk of personal injury in
the event of a collision.
Do not use accessory seat covers. The use of accessory seat
covers may prevent the deployment of the side airbags and
increase the risk of injury in an accident.
Do not lean your head on the door. The side airbag could injure
you as it deploys from the side of the seatback.
Do not attempt to service, repair, or modify the airbag SRS, its
fuses or the seat cover on a seat containing an airbag. See your
authorized dealer.
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
175
to inflate in side-impact collisions, not roll-over, rear-impact, frontal or
near-frontal collisions, unless the collision causes sufficient lateral
deceleration.
Several air bag system components get hot after inflation. Do not
touch them after inflation.
If the side airbag has
deployed,
the airbag will
not function again. The side
airbag system (including the
seat) must be inspected and
serviced by an authorized
dealer .
If the airbag is not
replaced, the unrepaired area will
increase the risk of injury in a
collision.
Safety Canopy™ system
Do not place objects or
mount equipment on or
near the headliner at the siderail
that may come into contact with a
deploying Safety Canopy™.
Failure to follow these instructions
may increase the risk of personal
injury in the event of a collision.
Do not lean your head on the door. The Safety Canopy™ could
injure you as it deploys from the headliner.
Do not attempt to service, repair, or modify the Safety Canopy™
system, its fuses, the A, B, C or D pillar trim, or the headliner on
a vehicle containing a Safety Canopy™. See your authorized dealer.
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
177
AUTOMATIC TRANSMISSION OPERATION
Brake-shift interlock – floor-shift transmission
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the ON position unless the brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the ON position and the brake pedal depressed, or when the ignition is
in the OFF position, it is possible that a fuse has blown or the vehicle’s
brakelamps are not operating properly. Refer to
Fuses and relays
in the
Roadside Emergencies
chapter.
If the fuse is not blown, perform the following procedure:
1. Apply the parking brake, turn the ignition to OFF, then remove the
key.
2. Using a screwdriver or similar
tool, remove the protective cover to
the interlock release access hole,
located to the right of the gearshift
lever.
3. Insert a screwdriver or similar
tool straight down into the access
hole and press downward while
pulling the gearshift lever out of the
P (Park) position and into the N
(Neutral) position.
4. Remove tool and reinstall the protective cover.
5. Start the vehicle and release the parking brake.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
247
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
Yellow
70A
Tan
Brown
80A
Natural
Black
Black
15
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
268
Passenger compartment fuse panel
The fuse panel is located under the right-hand side of the instrument
panel.
To remove the trim panel for access
to the fuse box, pull the panel
toward you and swing it out away
from the side and remove it. To
reinstall it, line up the tabs with the
grooves on the panel, then push it
shut.
To remove the fuse box cover, press in the tabs on both sides of the
cover, then pull the cover off.
To reinstall the fuse box cover, place the top part of the cover on the
fuse panel, then push the bottom part of the cover until you hear it click
shut. Gently pull on the cover to make sure it is seated properly.
The fuses are coded as follows.
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
269
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
1
30A
Smart window #1
2
15A
Driver side power seat memory
3
15A
FES, Audio rear seat controls, SDARS
4
30A
Smart window #2
5
10A
Keypad illumination, 3rd row seat enable,
Brake Shift Interlock (BSI), SPDJB
6
20A
Turn signals
7
10A
Low beam headlamps (left)
8
10A
Low beam headlamps (right)
9
15A
Interior lights
10
15A
Switch backlighting, Puddle lamps
11
10A
Not used (Spare)
12
7.5A
Power mirror switch, Driver seat switch
13
7.5A
Not used (Spare)
14
10A
Clock, Power liftgate module – keep-alive
power, Power running board module –
keep-alive power
15
10A
Climate control
16
15A
Not used (Spare)
17
20A
All lock motor feeds, Liftgate release,
Liftglass release
18
20A
Not used (Spare)
19
25A
Rear wiper
20
15A
Adjustable pedals, Datalink
21
15A
Fog lamps, Cornering lamps
22
15A
Park lamps relay
23
15A
High beam headlamps
24
20A
Horn relay
25
10A
Demand lamps, Glovebox, Visor
26
10A
Instrument panel cluster
27
20A
Ignition switch
28
5A
Radio
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
270
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
29
5A
Instrument panel cluster
30
5A
Not used (Spare)
31
10A
Compass, Automatic dimming rear view
mirror
32
10A
Restraints control module
33
10A
Not used (Spare)
34
5A
Not used (spare)
35
10A
Rear park assist, 4x4, rear video camera
36
5A
PATS transceiver
37
10A
Climate control
38
20A
Subwoofer/Amp (Audiophile radio), THX
Amp/DSP
39
20A
Radio
40
20A
THX Amp/DSP
41
15A
Not used (Spare)
42
10A
Trailer tow battery charge coil
43
10A
Rear wiper logic
44
10A
Not used (Spare)
45
5A
Front wiper logic
46
7.5A
Climate control, Auxiliary relay control
47
30A Circuit
Breaker
Power windows, Moon roof
48
Delayed accessory relay
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
Always disconnect the battery before servicing high current
fuses.
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
271
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
The high-current fuses are coded as follows:
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box Description
1
Blower relay
2
Not used
3
Rear window defroster relay
4
30A**
Third row seats (driver side)
5
30A**
Trailer tow connector (electric brake)
6
60A **
ABS (valves)
7
40A**
Power running boards
8
40A**
Heated/cooled seats
9
60A**
ABS (pump)
10
20A**
Rear console power point
11
30A**
Auxiliary blower
12
25A*
Trailer tow connector (park lamps)
13
30A*
Trailer tow connector (battery charge)
14
Not used
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
272
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box Description
15
Not used
16
A/C clutch relay
17
Driver side HID headlamp relay
18
Fuel pump relay
19
Back-up relay
20
Trailer tow connector relay (left turn signal)
21
Trailer tow connector relay (right turn signal)
22
Passenger side HID headlamp relay
23
15A*
Heated mirrors
24
40A**
Blower motor
25
Not used
26
Not used
27
30A**
Power liftgate
28
40A**
Rear window defroster, Heated mirror
29
30A**
Passenger seat
30
10A*
A/C clutch
31
15A*
Brake lamps
32
20A*
Fuel pump
33
20A*
Back-up lamps
34
25A*
Trailer tow connector (stop/turn lamps)
35
20A*
4x4 module
36
10A*
Powertrain Control Module (PCM) – Keep
alive power, Canister vent
37
15A*
Transmission B+
38
30A**
Third row seats (passenger side)
39
60A**
Air suspension pump
40
30A**
Starter motor
41
20A**
IP/Console power point
42
Not used
43
Not used
44
20A**
Driver side HID headlamp
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
273
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box Description
45
30A**
Driver seat
46
40A**
Run/Start bus bar
47
30A**
Air suspension – solenoids
48
20A**
Passenger side HID headlamp
49
30A**
Front wipers/washer
50
30A**
PCM – bus bar
51
20A**
Cargo power point
52
20A**
Cigarette lighter
53
Air suspension relay
54
Starter relay
55
Trailer tow connector relay (park lamp)
56
Trailer tow connector relay (battery charge)
57
Run/Start relay
58
Not used
59
PCM relay
60
One-touch Start diode
61
Not used
62
Fuel pump diode
63
15A*
Trailer tow connector (back-up lamp)
64
Not used
65
10A*
Air suspension logic
66
Not used
67
10A*
Blower coil
68
Not used
69
30A*
Run/Start – passenger compartment fuse panel
70
20A*
PCM (sensors) – EFC, A/C clutch coil
71
5A*
Fuel coil, ISP-R
72
20A*
PCM (ignition coils)
73
5A*
Transmission ignition
74
20A*
PCM (sensors) – HEGO/CMS, MAFS, EVMV,
CMCV, Speed deactivation switch, VCT
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
274
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box Description
75
5A*
4x4 Integrated Wheel Ends (IWE) solenoid
76
20A*
PCM – VPWR
77
10A*
ABS logic, Heated PCV
* Mini Fuses ** Cartridge Fuses
CHANGING THE TIRES
If you get a flat tire while driving, do not apply the brake heavily.
Instead, gradually decrease your speed. Hold the steering wheel firmly
and slowly move to a safe place on the side of the road.
Note:
The tire pressure monitoring system (TPMS) indicator light will
illuminate when the spare tire is in use. To restore the full functionality
of the monitoring system, all road wheels equipped with tire pressure
monitoring sensors must be mounted on the vehicle.
Have a flat serviced by an authorized dealer in order to prevent damage
to the TPMS sensors, refer to
Tire Pressure Monitoring System
(TPMS)
in the
Tires, Wheels and Loading
chapter. Replace the spare
tire with a road tire as soon as possible.
The use of tire sealants may damage your Tire Pressure
Monitoring System and should not be used.
Refer to
Tire Pressure Monitoring System (TPMS)
in the
Tires,
Wheels and Loading
chapter for important information. If the tire
pressure monitor sensor becomes damaged, it will no longer function.
Dissimilar spare tire/wheel information
Failure to follow these guidelines could result in an increased
risk of loss of vehicle control, injury or death.
If you have a dissimilar spare tire/wheel, then it is intended for
temporary use only. This means that if you need to use it, you should
replace it as soon as possible with a road tire/wheel that is the same size
and type as the road tires and wheels that were originally provided by
Ford. If the dissimilar spare tire or wheel is damaged, it should be
replaced rather than repaired.
2008 Navigator
(nav)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
275