Lincoln MKZ - 2008 Fuse Box Diagram

Lincoln MKZ - 2008 Fuse Box Diagram

CLOCK
Press the right (+) control to move
the time display forwards.
Press the left (-) control to move
the time display backwards.
AUXILIARY POWER POINT (12VDC)
Power outlets are designed for accessory plugs only. Do not insert
any other object in the power outlet as this will damage the
outlet and blow the fuse. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of the power
outlet can cause damage not covered by your warranty.
The auxiliary power point is located in the center console utility
compartment.
Do not use the power point for operating the cigarette lighter element (if
equipped).
To prevent the fuse from being blown, do not use the power point(s)
over the vehicle capacity of 12 VDC/180W. If the power point or cigar
lighter socket is not working, a fuse may have blown. Refer to
Fuses and
relays
in the
Roadside Emergencies
chapter for information on
checking and replacing fuses.
To have full capacity usage of your power point, the engine is required to
be running (in a safe manner) to avoid unintentional discharge of the
battery. To prevent the battery from being discharged:
do not use the power point longer than necessary when the engine is
not running,
do not leave battery chargers, video game adapters, computers and
other devices plugged in overnight or when the vehicle is parked for
extended periods.
Always keep the power point caps closed when not being used.
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Driver Controls
55
Always transport children 12 years old and under in the back
seat and always properly use appropriate child restraints.
National Highway Traffic Safety Administration (NHTSA)
recommends a minimum distance of at least 10 inches (25 cm)
between an occupant’s chest and the driver airbag module.
Never place your arm over the airbag module as a deploying
airbag can result in serious arm fractures or other injuries.
Steps you can take to properly position yourself away from the airbag:
Move your seat to the rear as far as you can while still reaching the
pedals comfortably.
Recline the seat slightly (one or two degrees) from the upright
position.
Do not put anything on or over the airbag module. Placing
objects on or over the airbag inflation area may cause those
objects to be propelled by the airbag into your face and torso causing
serious injury.
Do not attempt to service, repair, or modify the airbag
supplemental restraint system (SRS) or its fuses. See your
authorized dealer.
Modifying or adding equipment to the front end of the vehicle
(including frame, bumper, front end body structure and tow
hooks) may affect the performance of the airbag system, increasing the
risk of injury. Do not modify the front end of the vehicle.
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
126
Do not attempt to service, repair, or modify the airbag SRS, its
fuses or the seat cover on a seat containing an airbag. See your
authorized dealer.
All occupants of the vehicle should always wear their safety belts
even when an airbag SRS is provided.
How does the side airbag system work?
The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags (including side air
curtain systems).
The side airbag system consists of
the following:
An inflatable nylon bag (airbag)
with a gas generator concealed
behind the outboard bolster of
the driver and front passenger
seatbacks.
The same warning light,
electronic control and diagnostic
unit as used for the front airbags.
Two crash sensors located under the outboard side of the front seats,
attached near the floor.
Side airbags, in combination with safety belts, can help reduce the risk of
severe injuries in the event of a significant side impact collision.
The side airbags are fitted on the outboard side of the seatbacks of the
front seats. In certain lateral collisions, the airbag on the side affected by
the collision will be inflated. If the front passenger sensing system
detects an empty seat or an unbuckled child or small person, the front
passenger seat-mounted side airbag will be deactivated. The airbag was
designed to inflate between the door panel and occupant to further
enhance the protection provided occupants in side impact collisions.
The airbag SRS is designed to activate when the vehicle sustains lateral
deceleration sufficient to cause the sensors to close an electrical circuit
that initiates airbag inflation.
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
135
Side curtain airbag system
Do not place objects or
mount equipment on or
near the headliner at the siderail
that may come into contact with a
deploying side air curtain. Failure
to follow these instructions may
increase the risk of personal injury
in the event of a collision.
Do not place objects or mount equipment on or near the side air
curtain cover.
Do not lean your head on the door. The side airbag could injure
you as it deploys from the seat.
Do not attempt to service, repair, or modify the side air curtain
system, its fuses, the A, B, or C pillar trim, or the headliner on a
vehicle containing a side air curtain. See your authorized dealer.
All occupants of the vehicle, including the driver, should always
wear their safety belts even when an inflatable curtain is
provided.
To reduce the risk of injury, do not obstruct or place objects in
the deployment zone of the inflatable curtain.
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Seating and Safety Restraints
137
If you cannot move the gearshift lever out of P (Park) with ignition in
the RUN position and the brake pedal depressed:
1. Apply the parking brake, turn
ignition key to LOCK, then remove
the key.
2. Using a screwdriver (or similar
tool), remove the protective cover
to the interlock release access hole
on the console.
3. Insert the screwdriver (or similar
tool) into the access hole and press
downward while pulling the
gearshift lever out of the P (Park)
position and into the N (Neutral)
position.
4. Remove the tool and reinstall the
protective cover.
5. Start the vehicle and release the
parking brake.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to
Fuses and relays
in the
Roadside
Emergencies
chapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your authorized dealer as soon as possible.
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Driving
188
to turn them off. Use it when your vehicle is disabled and is creating a
safety hazard for other motorists.
Note:
With extended use, the flasher may run down your battery.
FUEL PUMP SHUT-OFF SWITCH
This device stops the electric fuel pump from sending fuel to the engine
when your vehicle has had a substantial jolt.
After an accident, if the engine cranks but does not start, this switch
may have been activated.
The fuel pump shut-off switch is
located in the front passenger
footwell area in the right upper
corner.
To reset the switch:
1. Turn the ignition to 1 (LOCK).
2. Check the fuel system for leaks.
3. If no leaks are apparent, reset the
switch by pushing in on the reset
button.
4. Turn the ignition to 3 (RUN).
5. Wait a few seconds and return
the key to 1 (LOCK).
6. Make another check for leaks.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.
15
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
201
Note:
Always replace a fuse with one that has the specified amperage
rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.
Standard fuse amperage rating and color
COLOR
Fuse
rating
Mini
fuses
Standard
fuses
Maxi
fuses
Cartridge
maxi
fuses
Fuse link
cartridge
2A
Grey
Grey
3A
Violet
Violet
4A
Pink
Pink
5A
Tan
Tan
7.5A
Brown
Brown
10A
Red
Red
15A
Blue
Blue
20A
Yellow
Yellow
Yellow
Blue
Blue
25A
Natural
Natural
30A
Green
Green
Green
Pink
Pink
40A
Orange
Green
Green
50A
Red
Red
Red
60A
Blue
Yellow
Yellow
70A
Tan
Brown
80A
Natural
Black
Black
Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
To remove a fuse use the fuse puller tool provided on the fuse panel
cover.
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
202
The fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
1
10A
Backup lamps, Electrochromatic
mirror
2
20A
Horns
3
15A
Battery saver: Interior lamps, Puddle
lamps, Trunk lamp, Glove box lamp,
Rear power windows
4
15A
Parklamps, License plate lamps
5
Not used
6
Not used
7
Not used
8
30A
Rear window defroster
9
10A
Heated mirrors
10
30A
Starter coil, PCM
11
15A
High beams
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
203
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse
Panel Description
12
7.5A
Delay accessories: Radio head units,
Moon roof, Front power windows,
Electrochromatic mirrors, Ambient
lighting
13
7.5A
Cluster, Analog clock, Climate control
head units
14
15A
Washer pump
15
20A
Cigar lighter
16
15A
Door lock actuator, Decklid lock
solenoid
17
20A
Not used (Spare)
18
20A
Radio head units, OBDII connector
19
7.5A
Not used (Spare)
20
7.5A
Power mirrors, Satellite radio module,
All wheel drive
21
7.5A
Stop lamps, CHMSL
22
7.5A
Audio
23
7.5A
Wiper relay coil, Cluster logic
24
7.5A
OCS (Passenger’s seat), PAD indicator
25
7.5A
RCM
26
7.5A
PATS Transceiver, Brake shift
interlock solenoid, Brake pedal
switch, Automatic transmission
module
27
7.5A
Cluster, Climate control head units
28
10A
ABS/Traction Control, Heated seats,
Compass, Reverse sensing system
C/B
30A Circuit
Breaker
Moon roof, Delayed accessory (SJB
fuse 12, rear power windows)
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
204
Power distribution box
The power distribution box is located in the engine compartment. The
power distribution box contains high-current fuses that protect your
vehicle’s main electrical systems from overloads.
Always disconnect the battery before servicing high current
fuses.
To reduce risk of electrical shock, always replace the cover to
the Power Distribution Box before reconnecting the battery or
refilling fluid reservoirs.
If the battery has been disconnected and reconnected, refer to the
Battery
section of the
Maintenance and Specifications
chapter.
The high-current fuses are coded as follows.
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
1
60A***
SJB power feed (fuses 12, 13, 14,
15, 16, 17, 18, C/B)
2
60A***
SJB power feed (fuses 1, 2, 4, 10,
11)
45 46 47 48 49
50
51
52
53
55
56
54
57
58
41
42
43
44
23 24 25 26 27
28
29
30
31
32
33
34
35
13
1
2
8
9
10
11
12
18
19
20
21
22
3
4
5
6
7
14 15 16 17
36
37
38
39
40
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
205
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
3
40A**
Powertrain power, PCM relay coil
4
40A**
Blower motor
5
Not used
6
40A**
Rear window defroster, Heated
mirrors
7
Not used
8
40A**
ABS pump
9
20A**
Wipers
10
30A**
ABS Valves
11
30A**
Heated seats, Passenger
heated/cooled seat
12
30A**
Driver heated/cooled seat
13
10A*
SYNC
14
15A*
Ignition switch
15
10A*
Memory module logic
16
15A*
Transmission
17
10A*
Alternator sense
18
Not used
19
40A**
Logic feed to SJB (solid state
devices)
20
20A**
THXII Amplifier #1
21
20A**
THXII Amplifier #2
22
20A**
Console power point
23
10A*
PCM KAM and canister vent
solenoid
24
15A*
Fog lamps
25
10A*
A/C Compressor clutch
26
15A*
LH HID Low beam
27
15A*
RH HID Low beam
28
80A***
Engine cooling fan
29
Not used
30
30A**
Fuel pump/injectors relay
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
206
Fuse/Relay
Location
Fuse Amp
Rating
Power Distribution Box
Description
31
30A**
Passenger power seat
32
30A**
Driver power seat
33
20A**
Moon roof
34
30A**
Driver Smart power window
35
30A**
Passenger Smart power window
36
1A*
PCM diode
37
1A*
One Touch Integrated Start
(OTIS) diode
38
Not used
39
Not used
40
Not used
41
Relay
Fog lamp relay
42
Relay
Wiper park relay
43
Relay
A/C clutch relay
44
Not used
45
Not used
46
15A*
Injectors
47
15A*
PCM class B
48
15A*
Coil on plug
49
15A*
PCM class C
50
Full ISO Relay
LH HID low beam relay
51
Full ISO Relay
RH HID low beam relay
52
Full ISO Relay
Blower relay
53
Not used
54
Full ISO Relay
Fuel pump/injectors relay
55
Full ISO Relay
Wiper RUN relay
56
Not used
57
Full ISO Relay
PCM relay
58
Not used
*Mini fuses **A1 fuses ***A3 fuses
2008 MKZ
(378)
Owners Guide (post-2002-fmt)
USA
(fus)
Roadside Emergencies
207