Acura RL - 2009 Fuse Box Diagram

Acura RL - 2009 Fuse Box Diagram

When you turn the ignition switch to
the LOCK (0) position and release it,
or remove the built-in key from the
ignition switch, the steering wheel
automatically moves fully in and up.
Steering wheel movement is also
controlled by the driving position
memory system (see page
).
To change the ‘‘AUTO TILT &
TELESCOPIC’’ setting, see page
.
If your vehicle’s battery is
disconnected or goes dead, or the
fuse for the power tilt and telescopic
steering wheel is removed, the
power tilt and telescopic steering
wheel system needs to be reset
when you reconnect the battery or
install the fuse.
The steering wheel returns to its
original position when you push the
ignition switch or insert the built-in
key back in the ignition switch.
Push the ignition switch for more
than 1 second and release it, or
insert the built-in key into the
ignition switch, and remove it. The
steering wheel automatically moves
fully in and up to let you know the
system is reset.
106
163
Steering Wheel Adjustments
Instruments and Controls
149
2009
RL
Your vehicle’s audio system may
disable itself if it is disconnected
from electrical power for any reason.
To make it work again, you must
enter a specific five-digit code with
the preset buttons. Because there
are hundreds of number
combinations possible from the five
digits, making the system work
without knowing the exact code is
nearly impossible.
If you lose the card, you must obtain
the code number from your dealer.
To do this, you will need the audio
system’s serial number.
If your vehicle’s battery is discon-
nected or goes dead, or the radio
fuse is removed, the audio system
will disable itself. If this happens,
you will see ‘‘
’’ in the upper
display the next time you turn on the
system. Use the preset buttons to
enter the code. The code is located
on the radio code card included in
your owner’s manual kit. When it is
entered correctly, the radio will start
playing.
If you make a mistake entering the
code, do not start over; complete the
five-digit sequence, then enter the
correct code. You have 10 tries to
enter the correct code.
If the code card is lost, your dealer
can access your code with your
radio’s serial number. To access the
serial number, turn the radio on. It
must display ‘‘
’’, then turn
the radio off. Push and hold the
preset 1 and preset 6 buttons, then
push the power/volume knob. The
serial number will appear in two sets
of four digits.
The system will retain your AM and
FM presets even if power is
disconnected.
You should have received a radio
code card that lists your audio
system’s code and serial numbers. It
is best to store this card in a safe
place at home. In addition, you
should write the audio system’s
serial number in this owner’s manual.
Radio Theft Protection
280
2009
RL
You can see the current latitude,
longitude, and elevation at any time
when you press the COMPASS
button or say ‘‘Display map guide.’’
The date and time is also displayed.
If the battery is disconnected
or the fuse for the compass system
is removed, the system may require
GPS initialization (see page
).
If the system does not receive the
elevation information, the display
shows only current latitude and
longitude.
If the GPS reception is low, the
display shows a ‘‘Low GPS
reception’’ message.
299
The Compass Screen
Compass System (U.S. model without navigation system)
286
NOTE:
2009
RL
Interface Dial Feedback
On
Auto
(default)
No
The system always
reads what you select.
The system reads your
selection only while
the vehicle is moving.
The system does not
read your selection.
Clock Adjustment
Changing this setting allows you to
control when (and if) the system will
read the current selection you
choose with the interface dial. This
feature can minimize the need to
look at the screen while operating
the dial. The three settings are
explained in the following table. The
factory default setting is
.
You can adjust the clock of your
system. When the battery is
disconnected or the fuse for the
compass system is removed, you
need to reset the time. See page
for more information on setting
the clock.
The second setup screen allows you
to change the system’s voice
recognition feedback, auto volume
for speed, and clock settings. To
select a setup item, turn the interface
knob until it is highlighted, then
push the interface selector in to
select it.
313
CONTINUED
AUTO
Setting
Feedback Level
Second Set up Screen
Compass System (U.S. model without navigation system)
Features
295
2009
RL
The third setup screen allows you to
change the system’s screen color
and verbal reminders. To select a
setup item, turn the interface knob
until it is highlighted, then push the
interface selector in to select it.
To view the third setup screen, move
the interface selector down. To
return to the first setup screen, say
‘‘Backward,’’ or move the interface
selector to the left to select BACK.
To view the second setup screen, say
‘‘More,’’ or move the interface
selector to the right to select MORE.
To go back to the first setup screen,
say ‘‘Backward,’’ or move the
interface selector to the left to select
BACK.
Allows you to turn voice control
system prompts
or
. To
select ON or OFF, turn the interface
knob to the right or left, then press
the interface selector. When
,
you will not hear the voice control
system confirmations or prompts.
This compass system automatically
increases the system voice volume
according to the vehicle speed. This
setting allows you to adjust the rate
of the volume increase.
When you select
, the volume is
not increased by the vehicle speed.
You can adjust the clock of your
system. When the battery is
disconnected or the fuse for the
compass system is removed, you
need to reset the time. See page
for more information on setting
the clock.
313
Voice Recognition Feedback
Auto Volume for Speed
Clock Adjustment
Third Set up Screen
Compass System (U.S. model without navigation system)
ON
OFF
OFF
OFF
296
2009
RL