Acura RL - 2007 Fuse Box Diagram

Acura RL - 2007 Fuse Box Diagram

When you turn the ignition switch to
the LOCK (0) position and release it,
or remove the built-in key from the
ignition switch, the steering wheel
automatically moves fully in and up.
Steering wheel movement is also
controlled by the driving position
memory system (see page
).
To change the ‘‘AUTO TILT &
TELESCOPIC’’ setting, see page
.
If your vehicle’s battery is
disconnected or goes dead, or the
fuse for the power tilt and telescopic
steering wheel is removed, the
power tilt and telescopic steering
wheel system needs to be reset
when you reconnect the battery or
install the fuse.
The steering wheel returns to its
original position when you push the
ignition switch or insert the built-in
key back in the ignition switch.
Push the ignition switch for more
than 1 second and release it, or
insert the built-in key into the
ignition switch, and remove it. The
steering wheel automatically moves
fully in and up to let you know the
system is reset.
160
106
Steering Wheel Adjustments
148
Your vehicle’s audio system will
disable itself if it is disconnected
from electrical power for any reason.
To make it work again, you must
enter a specific five-digit code with
the preset buttons. Because there
are hundreds of number
combinations possible from the five
digits, making the system work
without knowing the exact code is
nearly impossible.
You should have received a card that
lists your audio system code number
and serial number. It is best to store
this card in a safe place at home. In
addition, you should write the audio
system’s serial number in this owner’s
manual.
If you lose the card, you must obtain
the code number from your dealer.
To do this, you will need the audio
system’s serial number.
If your vehicle’s battery is discon-
nected or goes dead, or the radio
fuse is removed, the audio system
will disable itself. If this happens,
you will see ‘‘
’’ in the upper
display the next time you turn on the
system. Use the preset buttons to
enter the five-digit code. The code is
located on the radio code card
included in your owner’s manual kit.
When it is entered correctly, the
radio will start playing.
If you make a mistake entering the
code, do not start over; complete the
five-digit sequence, then enter the
correct code. You have 10 tries to
enter the correct code.
If the code card is lost, your dealer
can access your code with your
radio’s serial number. To access the
serial number, turn the radio on. It
must display ‘‘
’’, then turn
the radio off. Push and hold the
preset 1 and preset 6 buttons, then
push the power/volume knob. The
serial number will appear in two sets
of four digits.
The system will retain your AM and
FM presets even if power is
disconnected.
Radio Theft Protection
Features
239
You can see the current latitude,
longitude, and elevation at any time
when you press the COMPASS
button or say ‘‘Display map guide.’’
The date and time is also displayed.
If the battery is disconnected
or the fuse for the compass system
is removed, the system may require
GPS initialization (see page
).
If the system does not receive the
elevation information, the display
shows only current latitude and
longitude.
If the GPS reception is low, the
display shows a ‘‘Low GPS
reception’’ message.
258
The Compass Screen
Compass System (U.S. model without navigation system)
Features
245
NOTE:
CONTINUED
Color
Voice Recognition Feedback
Voice
Clock Adjustment
To view the Select a color screen,
say ‘‘Color,’’ or select COLOR on the
screen. You can choose from one of
five colors for the day and night
display modes.
The third setup screen allows you to
change the system’s screen color
and verbal reminders. To select a
setup item, turn the interface knob
until it is highlighted, then push the
interface selector in to select it.
To view the third setup screen, move
the interface selector down. To
return to the first setup screen, say
‘‘Backward,’’ or move the interface
selector to the left to select BACK.
Allows you to turn voice control
system prompts
or
. To
select ON or OFF, turn the interface
knob to the right or left, then press
the interface selector. When
,
you will not hear the voice control
system confirmations or prompts.
Allows you to select the guidance
voice:
or
. To
select MALE or FEMALE, turn the
interface knob to the right or left,
then press the interface selector.
You can adjust the clock of your
system. When the battery is
disconnected or the fuse for the
compass system is removed, you
need to reset the time. See page
for more information on setting
the clock.
272
Third Set up Screen
ON
OFF
OFF
MALE
FEMALE
Compass System (U.S. model without navigation system)
Features
255
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run.
When you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound, a series of clicks, or
nothing at all.
Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
are OK, there is probably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. See
on page
.
Diagnosing why the engine won’t
start falls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position:
Check these things:
Turn the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page
.
Check the transmission interlock.
The transmission must be in Park
or neutral or the starter will not
operate.
Make sure the remote is with you,
inside the vehicle.
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of the
battery and terminal connections
(see page
). You can then try
jump starting the vehicle from a
booster battery (see page
).
437
455
423
437
Nothing Happens or the Starter
Motor Operates Very Slowly
Emergency Towing
Jump Starting
If the Engine Won’t Start
436
In this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Are you using the proper starting
procedure? Refer to
on page
.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page
).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See
on page
.
Are you using a properly coded
built-in key or remote? An
improperly coded built-in key or
remote will cause the immobilizer
system indicator in the instrument
panel to blink rapidly (see page
).
Do you have fuel? Check the fuel
gauge; the low fuel indicator may
not be working.
Although this seems like a simple
procedure, you should take several
precautions.
You cannot start your vehicle by
pushing or pulling it.
64
341
449
455
The Starter Operates Normally
Starting the
Engine
Emergency
Towing
Jump Starting
If the Engine Won’t Start, Jump Starting
Taking Care of the Unexpected
437
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.
ʴ
ʴ
ʴ
Open the hood, and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or frozen, do not try
jump starting until it thaws.
Turn off all the electrical acces-
sories: heater, A/C, climate
control, stereo system, lights, etc.
Put the transmission in Park, and
set the parking brake.
Remove the battery cover (see
page
), then remove the
secondary under-hood fuse box
cover from the positive (
)
terminal on the battery.
Connect one jumper cable to the
positive (
) terminal on your
vehicle’s battery. Connect the
other end to the positive (
)
terminal on the booster battery.
The numbers in the illustration show
you the order to connect the jumper
cables.
1.
2.
3.
4.
424
To Jump Start Your Vehicle:
Jump Starting
438
COVER
BOOSTER BATTERY
If a battery sits in extreme cold, the
electrolyte inside can freeze.
Attempting to jump start with a frozen
battery can cause it to rupture.
ʴ
ʵ
Start your vehicle. If the starter
motor still operates slowly, check
that the jumper cables have good
metal-to-metal contact.
Once your vehicle is running,
disconnect the negative cable from
your vehicle, then from the
booster battery. Disconnect the
positive cable from your vehicle,
then from the booster battery.
Reinstall the secondary under-
hood fuse box cover over the
positive (
) terminal of the
battery, then reinstall the battery
cover.
If the booster battery is in another
vehicle, have an assistant start
that vehicle and run it at a fast idle.
Connect the second jumper cable
to the negative (
) terminal on
the booster battery. Connect the
other end to the grounding point
as shown. Do not connect this
jumper cable to any other part of
the engine.
Keep the ends of the jumper cables
away from each other and any metal
on the vehicle until everything is
disconnected. Otherwise, you may
cause an electrical short.
7.
5.
6.
8.
9.
Jump Starting
Taking Care of the Unexpected
439
Connecting the jumper cable to the
secondary under-hood fuse box causes
the fuses blown.
To remove the fuse box lid, put your
finger in the notch on the lid, pull it
toward you, and take it out of its
hinges.
The fuses are located in five fuse
boxes. The interior fuse boxes are
located under the dashboard on the
driver’s and passenger’s side.
To open the secondary fuse box lid,
push the tab in the direction as
shown in the illustration.
Fuses
Taking Care of the Unexpected
447
FUSE BOX
TAB
INTERIOR FUSE BOX
INTERIOR FUSE BOX
Driver’s side
SECONDARY INTERIOR FUSE BOX
Driver’s side
Passenger’s side
NOTCH
NOTCH
The primary under-hood fuse box is
in the engine compartment on the
driver’s side. To open it, push the
tabs as shown.
The secondary under-hood fuse box
is on the battery. To open it, push
the tabs as shown.
To check the fuse box, remove the
battery cover first (see page
).
424
Fuses
448
PRIMARY UNDER-HOOD FUSE BOX
SECONDARY UNDER-HOOD FUSE BOX
TAB
TAB
Turn the ignition switch to the
LOCK (0) position. Make sure the
headlights and all other
accessories are off.
If something electrical in your
vehicle stops working, the first thing
you should check for is a blown fuse.
Determine from the chart on pages
,
, and
, or the diagram
on the fuse box lid, which fuse or
fuses control that device. Check
those fuses first, but check all the
fuses before deciding that a blown
fuse is the cause. Replace any blown
fuses, and check if the device works.
Check each of the large fuses in
the under-hood fuse box by
looking through the top at the wire
inside. Removing these fuses
requires a Phillips-head
screwdriver.
Check the smaller fuses in the
under-hood fuse box and all the
fuses in the interior fuse boxes by
pulling out each fuse with the fuse
puller. The fuse puller is inside the
primary under-hood fuse box.
Remove the cover from the fuse
box.
3.
4.
1.
2.
452
453
454
Checking and Replacing Fuses
Fuses
Taking Care of the Unexpected
449
FUSE
BLOWN
FUSE
PULLER
If you cannot drive the vehicle
without fixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
from one of the other circuits with
the fuse puller provided in the under-
hood fuse box. Make sure you can
do without that circuit temporarily
(such as the accessory power socket
or radio).
If you replace the blown fuse with a
spare fuse that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
fuse with one of the correct rating as
soon as you can.
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem with your
vehicle. Leave the blown fuse in
that circuit, and have your vehicle
checked by a qualified technician.
Look for a blown wire inside the
fuse. If it is blown, replace it with
one of the spare fuses of the same
rating or lower.
6.
5.
Fuses
450
BLOWN
Replacing a fuse with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a
replacement fuse with the proper rating
for the circuit, install one with a lower
rating.
If the fuse for the driving position
memory system is removed, all
stored driving positions will be lost.
To store the driving positions again,
see page
.
If the navigation system fuse is
removed, the navigation system will
disable itself. The next time you turn
on the ignition switch, the system
will require you to enter a PIN
before it can be used. Refer to the
navigation system manual.
If the compass system fuse is
removed, the compass system will
disable itself. The next time you turn
on the ignition switch, the system
will require you to enter a PIN
before it can be used. Enter the four-
digit anti-theft security code (see
page
). You will also need reset
the clock according to the
instruction of the clock setting (see
page
).
If the radio fuse is removed, the
audio system will disable itself. The
next time you turn on the audio
system you will see ‘‘
’’ in the
frequency display. Use the preset
buttons to enter the five-digit code
(see page
).
If the fuse for the power tilt
telescopic steering is removed, the
system will be disabled. The system
needs to be reset after reinstalling
the fuse (see page
).
160
257
239
148
272
On vehicles with navigation system
On vehicles without navigation system
Fuses
Taking Care of the Unexpected
451
ˎ
ˎ
No.
Amps.
No.
Amps.
No.
Circuits Protected
Circuits Protected
Amps.
Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 A
30 A
10 A
15 A
10 A
15 A
7.5 A
15 A
30 A
30 A
20 A
7.5 A
15 A
40 A
1
50 A
15
16
17
18
19
20
21
22
23
Radiator fan
Left headlight low beam
Rear defroster coil
Left headlight high beam
Small light
Right headlight high beam
Right headlight low beam
Back-up
FI ECU
Wiper
Headlight washer
Fog lights
MG clutch
Horn, Stop
Rear defroster
40 A
15 A
30 A
40 A
40 A
(40 A)
40 A
70 A
120 A
50 A
50 A
Back-up, ACC
Hazard
ABS/VSA motor
ABS/VSA
Drive by wire, LAF heater
Option
Heater motor
Passenger’s fuse box
Battery
IG main
Power window
: On Canadian models
Fuse Locations
452
PRIMARY UNDER-HOOD FUSE BOX
SECONDARY UNDER-HOOD FUSE BOX
No.
No.
Circuits Protected
Amps.
Amps.
Amps.
No.
Circuits Protected
Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
Starter diag.
Starter signal
15 A
15 A
10 A
15 A
7.5 A
7.5 A
10 A
20 A
20 A
7.5 A
7.5 A
7.5 A
20 A
20 A
10 A
20 A
7.5 A
7.5 A
20 A
15 A
20 A
15 A
10 A
10 A
7.5 A
20 A
20 A
20 A
30 A
20 A
7.5 A
7.5 A
7.5 A
10 A
(7.5 A)
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Drive by Wire
Ignition coil
Daytime running light
LAF heater
Radio
Interior light
Back-up
Door lock
Accessory socket
Occupant position detection
system
Wiper
Driver’s power seat sliding
Power lumbar support
Driver’s power seat reclining
ACG
Fuel Pump
IGN SOL
Meter
SRS
IGP (PGM-FI ECU)
Left rear power window
ETS (telescopic)
ETS (tilt)
Driver’s power window
Moonroof
Adaptive Front Lighting
System
Air Conditioner
e-pretensioner
ACC
Option
Tire pressure monitoring system
Passenger’s power seat reclining
Passenger’s power seat sliding
Fuse Locations
Taking Care of the Unexpected
453
INTERIOR FUSE BOX
Driver’s side
SECONDARY INTERIOR FUSE BOX
Driver’s side
No.
Amps.
Circuits Protected
No.
Amps.
Circuits Protected
1
2
3
4
5
30 A
30 A
30 A
30 A
20 A
SH-AWD
Premium amplifier
Passenger’s power window
Driver’s automatic seat belt
tensioner/e-pretensioner
Right rear power window
6
7
8
9
20 A
7.5 A
30 A
7.5 A
Heated seats
Interior lights
Passenger’s automatic seat
belt tensioner/
e-pretensioner
Air conditioner
Fuse Locations
454
INTERIOR FUSE BOX
Passenger’s side
ʵ
ʵ
ʵ
ʵ
ˎ
ˎ
ˎ
ˎ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
ʴ
ʵ
ˎ
ˎ
ˎ
Specifications
Technical Information
461
Engine
Alignment
Tires
Lights
Fuses
Battery
12 V
12 V
60 W
24/2.2 CP
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
Type
Bore x Stroke
Displacement
Compression ratio
Spark plugs
Spark plug gap
3.54 x 3.58 in (89 x 93 mm)
212 cu-in (3,471 cm
)
11.0 : 1
IZFR6K11
SKJ20DR-M11
0.04 in (1.1 mm)
0.00 in (0.0 mm)
0.08 in (2.0 mm)
0°8’
1°15’
2°10’
P245/50R17 98V
SOHC VTEC V-6 gasoline engine
Toe-in
Camber
Caster
Size
Pressure
60 psi (420 kPa , 4.2 kgf/cm
)
30 psi (210 kPa , 2.1 kgf/cm
)
32 psi (220 kPa , 2.2 kgf/cm
)
T155/70D17 110M
245-680R460A 102V
Headlights
(High Beam)
Front turn signal/parking lights
Front side marker
Rear turn signal lights
Back-up light
Fog lights
License plate lights
Ceiling lights
Vanity mirror lights
Door courtesy lights
Trunk light
12 V
5 W
2 CP
2 W
8 W
8 W
5 W
55 W
21 W
21 W
3 CP
Low beam headlight bulbs are a type of high voltage discharge
tube (D2S).
Interior
Under-hood
Capacity
12 V
12 V
72 AH/20 HR
55 AH/5 HR
See page
453
and
454
or the fuse
label attached to the inside of
each fuse box cover.
See page
452
or the fuse box
cover.
12 V
21 W
Front
Rear
Front
Rear
Front
Front
Rear
NGK:
DENSO:
Front/Rear
Spare
Front
Rear
Spare
1 : Michelin PAX system model
2 : If equipped
(HB3)
(Amber)
(5W)
(Amber)
(H11)
On model without adaptive front lighting system
1 :
2 :
(Amber)
1
0
0.1 mm
1
2
2