Acura MDX - 2006 Fuse Box Diagram

Acura MDX - 2006 Fuse Box Diagram

ʵ
If the driver’s
window senses any obstacle while it
is closing automatically, it will
reverse direction, and then stop. To
close the window, remove the
obstacle, then use the window switch
again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
before closing it.
If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window fuse is removed, the
AUTO function will be disabled. The
power window system needs to be
reset after reconnecting the battery
or installing the fuse.
Start the engine. Push down and
hold the driver’s window switch
until the window is fully open.
Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
for about 2 seconds.
If the power windows do not operate
properly after resetting, have your
vehicle checked by your dealer.
To open the moonroof, pull back the
moonroof switch firmly.
To close the moonroof fully, push
the switch forward.
1.
2.
CONTINUED
AUTO REVERSE
Moonroof
Power Windows, Moonroof
Instruments and Controls
93
MOONROOF SWITCH
ʵ
ʵ
The SCAN function gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button or
touch the SCAN icon on the audio
display (models with navigation
system). The system plays each
channel in numerical order for a few
seconds, then selects the next
channel. When you hear a channel
you want to continue listening to,
press the button or touch the icon
again.
Pick the preset button (icon) you
want for that channel. Press and
hold the button (icon) until you
hear a beep.
Repeat steps 2 and 3 to store the
first six channels.
Once a channel is stored, simply
press and release the proper preset
button (icon) to tune to it.
The presets will be lost if your
vehicle’s battery goes dead, is
disconnected, or the radio fuse is
removed.
Press the XM button again. The
other XM band will show. Store
the next six channels using steps 2
and 3.
You can store up to 12
preset channels using the six preset
buttons or preset icons (on models
with navigation system). Each button
stores one channel from the XM1
band and one channel from the XM2
band.
To store a channel:
Press the XM button. Either XM1
or XM2 will show in the display.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
In the category mode, only channels
within that category can be selected.
In the channel mode, all channels
can be selected.
3.
4.
5.
1.
2.
Playing the XM
Satellite Radio (U.S. Models)
SCAN
Preset
120
Diagnosing why the engine won’t
start falls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position:
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run.
When you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound or series of clicks, or
nothing at all.
Check the transmission interlock.
The transmission must be in Park
or neutral or the starter will not
operate.
Turn the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page
.
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is dis-
charged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page
). You can
then try jump starting the vehicle
from a booster battery (see page
).
In this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the dash panel to blink
rapidly (see page
).
Check these things:
Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
are OK, there is probably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem (see
on page
).
80
268
257
268
275
CONTINUED
If Your Engine Won’t Start
Nothing Happens or the Starter
Motor Operates Very Slowly
Jump Starting
The Starter Operates Normally
Emergency Towing
Taking Care of the Unexpected
267
Are you using the proper starting
procedure? Refer to
on page
.
Do you have fuel? Check the fuel
gauge; the warning indicator may
not be working.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page
).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See
on page
.
Although this seems like a simple
procedure, you should take several
precautions.
To jump start your vehicle:
You cannot start your vehicle by
pushing or pulling it.
Put the transmission in neutral or
Park, and set the parking brake.
Turn off all the electrical acces-
sories: heater, A/C, climate
control, audio system, lights, etc.
Open the hood, and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or frozen, do not try
jump starting until it thaws.
1.
2.
201
277
275
Starting the
Engine
Emergency
Towing
Jump Starting
If the Engine Won’t Start, Jump Starting
268
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.
If a battery sits in extreme cold, the
electrolyte inside can freeze.
Attempting to jump start with a frozen
battery can cause it to rupture.
The interior fuse boxes are located
under the dashboard on the driver’s
and passenger’s side.
The vehicle’s fuses are contained in
five fuse boxes.
To open the passenger’s side fuse
box, pull the right edge of the cover.
The primary under-hood fuse box is
on the passenger’s side. The
secondary fuse box is next to the
battery.
Fuses
276
PASSENGER’S SIDE INTERIOR
UNDER-HOOD (SECONDARY)
DRIVER’S SIDE
INTERIOR
UNDER-HOOD (PRIMARY)
If something electrical in your
vehicle stops working, the first thing
you should check for is a blown fuse.
Determine from the chart on pages
and
, or the diagram on the
fuse box lid, which fuse or fuses
control that device. The diagram for
the interior driver’s side fuse box is
on the kick panel below the fuse box.
Check those fuses first, but check all
the fuses before deciding that a
blown fuse is the cause. Replace any
blown fuses, and check if the device
works.
Turn the ignition switch to the
LOCK (0) position. Make sure the
headlights and all other
accessories are off.
Remove the cover from the fuse
box.
Check each of the large fuses in
the primary under-hood fuse box
by looking through the top at the
wire inside. Removing these fuses
requires a Phillips-head
screwdriver.
Check the smaller fuses in the
under-hood fuse boxes and all the
fuses in the interior fuse box by
pulling out each one with the fuse
puller provided in the primary
under-hood fuse box.
4.
3.
1.
2
279
280
Checking and Replacing Fuses
Fuses
Taking Care of the Unexpected
277
BLOWN
FUSE PULLER
If you cannot drive the vehicle
without fixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
from one of the other circuits. Make
sure you can do without that circuit
temporarily (such as the accessory
power socket or radio).
If you replace the blown fuse with a
spare fuse that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
fuse with one of the correct rating as
soon as you can.
Look for a burned wire inside the
fuse. If it is burned out, replace it
with one of the spare fuses of the
same rating or lower.
If the radio fuse is removed, the
audio system will disable itself. The
next time you turn on the radio you
will see ‘‘
’’ in the frequency
display. Use the preset buttons to
enter the five-digit code (see page
).
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem with your
vehicle. Leave the blown fuse in
that circuit, and have your vehicle
checked by a qualified mechanic.
6.
5.
131
Fuses
278
BLOWN
Replacing a fuse with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a
replacement fuse with the proper rating
for the circuit, install one with a lower
rating.
ʵ
No.
Amps.
Circuits Protected
No.
Amps.
Circuits Protected
No.
Amps.
No.
Amps.
Circuits Protected
Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12
13
20 A
30 A
20 A
15 A
15 A
20 A
20 A
20 A
40 A
30 A
30 A
40 A
Spare Fuse
Spare Fuse
Right Headlight
ACG S
Hazard
Not used
Stop
Left Headlight
Radio
Power Window Motor
Rear A/C
Rear Defroster
Back Up, ACC
14
15
16
17
18
19
20
21
22
23
24
40 A
40 A
30 A
7.5 A
10 A
15 A
120 A
30 A
7.5 A
50 A
20 A
Power Seat
Heater Motor
Cooling Fan
Spare Fuse
Spare Fuse
Spare Fuse
Battery
Condenser Fan
MG Clutch
IGI Main
Fog Lights
1
2
3
4
5
20 A
40 A
30 A
20 A
20 A
6
7
8
9
10
15 A
15 A
15 A
7.5 A
20 A
ETC
IG Coil
LAF
FI-Back-up
P/W DR
Rear Entertainment System
VSA F/S Relay
VSA Motor
4WD
Rear Accessory Socket
Fuse Locations
Taking Care of the Unexpected
279
PRIMARY UNDER-HOOD FUSE BOX
SECONDARY UNDER-HOOD FUSE BOX
ʵ
ˎ
ˎ
ˎ
ˎ
Circuits Protected
No.
Amps.
No.
Amps.
Circuits Protected
Circuits Protected
No.
Amps.
Horn
Auto Wipers
1
2
3
7.5 A
7.5 A
7.5 A
1
2
3
4
5
6
7
8
9
10
11
12
13
15 A
10 A
7.5 A
7.5 A
10 A
15 A
7.5 A
7.5 A
10 A
7.5 A
15 A
30 A
Fuel Pump
SRS
Heater Control, A/C Clutch
Relay, Cooling Fan Relay
Power Mirror
Daytime Running Light /
Rear Wiper
ECU (PCM), Cruise Control
OPDS, OnStar
ACC Relay
Back-up Lights, Instrument
Lights, TPMS
Turn Signals
IG Coil
Front Wiper
Not Used
Moonroof
Driver’s Power Seat Sliding
Passenger’s Power Seat
Reclining
Daytime Running Light,
OnStar
Driver’s side Rear Power
Window
Front Passenger’s Power
Window
Front Accessory Socket,
HFL, OnStar
Small Light
Interior Light, TPMS, HFL
Power Door Lock
Back Up, Clock
Heated Seat
Driver’s Power Window
Passenger’s Side Rear
Power Window
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
30 A
20 A
20 A
20 A
20 A
10 A
20 A
20 A
15 A
15 A
10 A
20 A
7.5 A
20 A
20 A
20 A
:
Canadian models
Canadian models
:
ELD Unit, Immobilizer Control
Unit, VSA Control Unit, Alternator
Driver’s Power Seat Reclining
Passenger’s Power Seat Sliding
Fuse Locations
280
Driver’s Side
INTERIOR FUSE BOX
Passenger’s Side
Front
Front
Driver’s Side
Auxiliary
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
Specifications
Technical Information
285
Battery
Fuses
Engine
Alignment
Tires
Lights
60 W (HB3)
12 V
10.0 : 1
211.8 cu-in (3,471 cm
)
3.50 x 3.66 in (89.0 x 93.0 mm)
12 V
55 W (H11)
3 CP
12 V
28/8 W
12 V
51 W (HB4)
12 V
5 W
12 V
21 W
12 V
21 W/5 W
12 V
21 CP (18 W)
12 V
3 CP
12 V
21 W
12 V
5 W
12 V
5 W
5 W
5 W
1.1 W
3.8 W
12 V
12 V
12 V
12 V
12 V
12 V
52 AH/5 HR
Capacity
Interior
Under-hood
Type
Bore x Stroke
Displacement
Compression ratio
Spark plugs
IZFR5K-11
SKJ16DR-M11
Water cooled 4-stroke SOHC,
V6 gasoline engine
Toe-in
Camber
Caster
Size
Pressure
0.00 in (0.0 mm)
0.00 in (0.0 mm)
0°50’
0°50’
1°53’
P235/65R17 103T
T155/90D16 110M
32 psi (220 kPa , 2.2 kgf/cm
)
60 psi (420 kPa , 4.2 kgf/cm
)
Headlights
Front side marker lights
Front turn signal lights/
Parking lights
Fog light
Front foot lights
Rear turn signal/hazard lights
Brake/Taillights
Backup lights
License plate lights
High-mount brake light
Individual map lights
Cargo area light
Tailgate light
Vanity mirror light
Door light
12 V
65 AH/20 HR
See page
280
or the fuse label
attached to the dashboard.
See page
280
or the fuse label
attached to the inside of the fuse
box door under the dashboard.
See page
279 o
r the fuse box
cover.
Front/Rear
Spare
Front/Rear
Spare
Front
Rear
Front
Rear
Front
Front
Rear
Driver’s side
Passenger’s side
High
Low
NGK:
DENSO: