Acura TSX - 2004 Fuse Box Diagram

Acura TSX - 2004 Fuse Box Diagram

If your car’s battery is disconnected
or goes dead, or the driver’s window
fuse is removed, the AUTO function
will be disabled. The power window
system needs to be reset after
reconnecting the battery or installing
the fuse. You should do the following.
Start the engine. Push down on
the driver’s window switch until
the window is fully open.
Pull back on the driver’s window
switch to close the window
completely, then hold the switch
for a second or two more.
If the power windows do not operate
properly after resetting, have your
car checked by an Acura dealer.
The power window system has a key-
off delay function. The windows will
still operate for up to 10 minutes
after you turn off the ignition.
Opening either front door cancels
the delay function. You must turn
the ignition switch to ON (II) again
before you can raise or lower the
windows.
1.
2.
Power Windows
Instruments and Controls
99
ʵ
ʵ
To store a frequency:
Use the TUNE, SEEK, or SCAN
function to tune the radio to a
desired station.
You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two frequencies with each preset
button.
Pick the preset button you want
for that station. Press the button
and hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
The preset frequencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio fuse is
removed.
The SCAN function
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan up
the band for a station with a strong
signal. When it finds one, it will stop
and play that station for about 5
seconds. If you do nothing, the
system will then scan for the next
strong station and play that for 5
seconds. When it plays a station that
you want to continue listening to,
press the SCAN button again.
1.
2.
3.
4.
Preset
SCAN
Audio System
Comfort and Convenience Features
131
ʵ
ʵ
ʵ
You can store the
frequencies of your favorite radio
stations in the six preset icons. Each
icon will store one frequency on the
AM band, and two frequencies on
the FM band.
To store a frequency:
Repeat steps 2 to 4 to store a total
of six stations on AM and twelve
on FM.
Once a station’s frequency is stored,
simply touch the proper preset icon
to tune to it.
The preset frequencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio fuse is
removed.
If you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
To activate Auto Select, touch the
Auto Select icon on the display. The
A.SEL indicator will flash in the
upper display, and the system will go
into scan mode for several seconds.
It automatically scans both bands,
looking for stations with strong
signals. It stores the frequencies of
six AM stations and twelve FM
stations in the preset icons. You can
then use the preset icons to select
those stations.
Pick the preset icon (1
6) you
want for that station. Touch the
icon, and hold it until you hear two
beeps.
Use the TUNE, SEEK, or SCAN
function to tune the radio to a
desired station.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two frequencies with each preset
icon.
Push the AUDIO DISPLAY button
to view the audio display. You will
see the six preset icons.
1.
2.
3.
4.
5.
Preset
AUTO SELECT
Audio System
Comfort and Convenience Features
150
When all the digits in the code are
entered correctly, the radio will start
playing.
You should have received a card that
lists your audio system’s code
number and serial number. It is best
to store this card in a safe place at
home. In addition, you should write
the audio system’s serial number in
this Owner’s Manual. If you should
happen to lose the card, you must
obtain the code number from your
Acura dealer. To do this, you will
need the system’s serial number.
You will have to store your favorite
stations in the preset buttons after
the system begins working. Your
original settings were lost when
power was disconnected.
Your car’s audio system will disable
itself if it is disconnected from
electrical power for any reason. To
make it work again, the user must
enter a specific code using the preset
buttons or the TUNE knob. Because
there are hundreds of number
combinations possible, making the
system work without knowing the
exact code is nearly impossible.
If your car’s battery is disconnected
or goes dead, or the radio fuse is
removed, the audio system will
disable itself. If this happens, you
will see ‘‘
’’/‘‘
’’ in the
frequency display the next time you
turn on the system. Use the preset
buttons or the TUNE knob to enter
the code.
If your car is equipped with a
navigation system, press and release
the TUNE knob; the number ‘‘0’’
appears on the display.
If ‘‘0’’ is the first digit in your code,
press and release the TUNE knob
to store it.
If ‘‘0’’ is not the first digit in your
code, turn the TUNE knob left or
right until the first digit is
displayed. Press and release the
TUNE knob to store it. Enter the
remaining digits the same way.
If you make a mistake entering the
code, do not start over or try to
correct your mistake. Complete the
sequence, then enter the correct
code. You have ten tries to enter the
correct code. If you are unsuccessful
in ten attempts, you must then leave
the system on for 1 hour before
trying again.
Theft Protection
Audio System
Comfort and Convenience Features
172
Turn the ignition switch to START
(III). If the headlights do not dim,
check the condition of the fuses. If
the fuses are OK, there is proba-
bly something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. (See
on page
.)
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is dis-
charged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page
). You can
then try jump starting the car from
a booster battery (see page
).
In this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to START (III), but
the engine does not run.
Are you using the proper starting
procedure? Refer to
on page
.
Your car has the Immobilizer
System. You should use a
properly-coded master or valet key
to start the engine (see page
).
A key that is not properly coded
will cause the immobilizer system
indicator in the dash panel to blink
rapidly.
Do you have fuel? Turn the
ignition switch to ON (II) for a
minute and watch the fuel gauge.
The low fuel level warning light
may not be working, so you were
not reminded to fill the tank.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page
).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See
on page
.
328
312
265
199
324
328
79
If Your Engine Won’t Start
Taking Care of the Unexpected
Emergency Towing
The Starter Operates Normally
Starting the
Engine
Emergency
Towing
311
Use a screwdriver or coin to
remove the round plug in the
center of the headliner.
Remove the wrench. Reinstall the
round plug.
Insert the moonroof wrench into
the socket behind this plug. Turn
the wrench until the moonroof is
fully closed.
If the electric motor will not close
the moonroof, do the following:
Check the fuse for the moonroof
motor (see page
). If the fuse
is blown, replace it with one of the
same or lower rating.
Try closing the moonroof. If the
new fuse blows immediately or the
moonroof motor still does not
operate, you can close the
moonroof manually.
Get the moonroof wrench out of
the tool kit in the trunk.
If you need to close the moonroof
manually, it means your car’s
moonroof opening/closing function
is developing a problem. Have your
car checked by an Acura dealer.
5.
6.
4.
3.
1.
2.
327
Closing the Moonroof
Taking Care of the Unexpected
322
ROUND PLUG
SOCKET
All the electrical circuits in your car
have fuses to protect them from a
short circuit or overload. These
fuses are located in two fuse boxes.
The under-hood fuse box is located
near the back of the engine compart-
ment on the driver’s side. To open it,
push the tabs as shown.
The interior fuse box is on the
driver’s lower left side. To remove
the fuse box lid, put your finger in
the notch on the lid, and pull it
toward you and take it out of its
hinges.
Fuses
Taking Care of the Unexpected
323
INTERIOR
UNDER-HOOD
TAB
NOTCH
Turn the ignition switch to LOCK
(0). Make sure the headlights and
all other accessories are off.
Remove the cover from the fuse
box.
If something electrical in your car
stops working, the first thing you
should check for is a blown fuse.
Determine from the chart on pages
and
, or the diagram on the
fuse box lid, which fuse or fuses
control that component. Check those
fuses first, but check all the fuses
before deciding that a blown fuse is
not the cause. Replace any blown
fuses and check the component’s
operation.
Check each of the large fuses in
the under-hood fuse box by
looking at the wire inside.
Removing these fuses requires a
Phillips-head screwdriver.
3.
1.
2.
326
327
Checking and Replacing Fuses
Fuses
Taking Care of the Unexpected
324
BLOWN
BLOWN
CONTINUED
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem in your car.
Leave the blown fuse in that
circuit and have your car checked
by a qualified mechanic.
If you cannot drive the car without
fixing the problem, and you do not
have a spare fuse, take a fuse of the
same rating or a lower rating from
one of the other circuits. Make sure
you can do without that circuit
temporarily (such as the accessory
power socket or radio).
If you replace the blown fuse with a
spare fuse that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
fuse with one of the correct rating as
soon as you can.
Look for a burned wire inside the
fuse. If it is burned, replace it with
one of the spare fuses of the same
rating or lower.
Check the smaller fuses in the
under-hood fuse box and all the
fuses in the interior fuse box by
pulling out each fuse with the fuse
puller provided in the under-hood
fuse box.
5.
6.
4.
Fuses
Taking Care of the Unexpected
325
BLOWN
FUSE PULLER
Replacing a fuse with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a replace-
ment fuse with the proper rating for the
circuit, install one with a lower rating.
ʵ
ʵ
ʵ
ʴ
Circuits Protected
No.
No.
No.
Amps.
Amps.
Amps.
Circuits Protected
Circuits Protected
Left Headlight Low
(Rear Defroster Coil)
Left Headlight Hi
Small Light
Right Headlight Hi
6
7
8
9
10
1
2
3
4
5
11
12
13
14
15
16
17
18
19
20
21
22
23
15 A
(30A)
10 A
15 A
10 A
15 A
7.5 A
15 A
20 A
20 A
20 A
40 A
40 A
15 A
30 A
40 A
40 A
40 A
40 A
100 A
50 A
50 A
Cooling Fan
Not Used
Horn, Stop
Rear Defroster
Back Up, ACC
Hazard
VSA Motor
VSA
OP 1
OP 2
Heater Motor
Battery
Not Used
B IG1 Main
Power Window Main
Right Headlight Low
Back Up
FI ECU
Condenser fan
Not Used
Fuses
Taking Care of the Unexpected
326
UNDER-HOOD FUSE/RELAY BOX
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
ˎ
No.
No.
No.
Amps.
Circuits Protected
Amps.
Circuits Protected
Circuits Protected
Amps.
: On Canadian models
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
1
2
3
4
5
6
7
8
9
10
11
12
10 A
20 A
15 A
7.5 A
30 A
Back-Up Lights
Door Lock
Front Accessory Sockets
IG OPDS
IG Wiper
Not Used
(15 A)
15 A
(10 A)
10 A
20 A
10 A
DBW
Ignition Coil
Day Light
LAF
Audio Amp
Interior Light
Not Used
Driver’s Power Seat Sliding
Heated Seat
Driver’s Power Seat Reclining
Not Used
IG ACG
IG Fuel Pump
IG Washer
IG Meter
IG SRS
IGP (PGM-FI ECU)
Left Rear Power Window
Right Rear Power Window
Right Front Power Window
Driver’s Power Window
Moonroof
Not Used
IG HAC
Not Used
ACC
HAC OP
(20 A)
(20 A)
(20 A)
15 A
15 A
7.5 A
7.5 A
10 A
7.5 A
20 A
20 A
20 A
20 A
(20 A)
7.5 A
7.5 A
7.5 A
Fuses
Taking Care of the Unexpected
327
INTERIOR FUSE BOX
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
CONTINUED
Specifications
Technical Information
335
Alignment
Engine
Fuses
Battery
Lights
12 V
21 W
12 V
12 V
12 V
12 V
12 V
21 W
21/5 W
5 W
21 W
21 W
12 V
55 W
12 V
35 W
12 V
3 CP
Water cooled 4-stroke, DOHC
i-VTEC 4-cylinder, gasoline engine
3.43 x 3.90 in (87.0 x 99.0 mm)
144 cu-in (2,354 cm
)
10.5 : 1
Toe-in
Camber
Caster
0.00 in (0.0 mm)
0.08 in (2.0 mm)
3°13’
Type
Bore x Stroke
Displacement
Compression ratio
Spark plugs
See spark plug maintenance sec-
tion page
264
.
See page
326
or the fuse box
cover.
See page
327
or the fuse label
attached to the inside of the fuse
box door on each side of the
dashboard.
Interior
Under-hood
Capacity
12 V
38 AH/5 HR
12 V
12 V
12 V
12 V
12 V
12 V
1.1 W
2 CP
5 W
8 W
8 W
3 CP
12 V
3 CP
Headlights
Front turn signal
Front parking lights
Rear turn signal lights
Stop/Taillights
Taillights
High-mount brake light
Back-up lights
Rear side marker light
License plate light
Ceiling light
Spotlights/Front ceiling lights
Trunk light
Door courtesy light
Vanity mirror lights
Front
Rear
Front
Rear
Front
High
Low