Acura RL - 2004 Fuse Box Diagram

Acura RL - 2004 Fuse Box Diagram

There are two switches on the
ceiling near the front ceiling light.
The ignition switch must be ON (II).
To open the moonroof, pull the
OPEN/CLOSE switch backward and
hold it until the moonroof reaches
the desired position.
If your car’s battery is disconnected
or goes dead, or the driver’s window
fuse is removed, the AUTO function
will be disabled. The power window
system needs to be reset after
reconnecting the battery or installing
the fuse. You should do the following.
Pull back on the driver’s window
switch to close the window
completely then hold the switch
for a further second or two more.
Start the engine. Push down on
the driver’s window switch until
the window is fully open.
The power window system has a key-
off delay function. The windows will
still operate for up to ten minutes
after you turn off the ignition.
Opening either front door cancels
the delay function. You must turn
the ignition switch ON (II) again
before you can raise or lower the
windows.
If the power windows do not operate
properly after resetting, have your
car checked by an Acura dealer.
1.
2.
CONTINUED
Moonroof
Power Windows, Moonroof
Instruments and Controls
105
OPEN/CLOSE
SWITCH
ʵ
The preset frequencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio fuse is
removed.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Pick the preset button you want
for that station. Press the button
and hold it until you hear a beep.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two frequencies with each preset
button.
To store a frequency:
You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
Use the TUNE, SEEK, or SCAN
function to tune the radio to a
desired station.
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
1.
2.
3.
4.
Preset
Audio System
Comfort and Convenience Features
136
PWR/VOL
KNOB
AM
BUTTON
FM
BUTTON
TUNE KNOB
SCAN BUTTON
PRESET BUTTONS
ST INDICATOR
SEEK BUTTONS
ʵ
The preset frequencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio fuse is
removed.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Pick the preset button you want
for that station. Press the button
and hold it until you hear a beep.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two frequencies with each preset
button.
To store a frequency:
You can store the
frequencies of your favorite radio
stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
Use the TUNE, SEEK, or SCAN
function to tune the radio to a
desired station.
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
1.
2.
3.
4.
CONTINUED
Audio System
Comfort and Convenience Features
Preset
153
PWR/VOL
KNOB
TUNE KNOB
SCAN BUTTON
PRESET BUTTONS
ST INDICATOR
AM/FM BUTTON
SEEK BUTTONS
ʵ
ʵ
The SCAN function gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button. The
system plays each channel in
numerical order for a few seconds,
then selects the next channel. When
you hear a channel you want to
continue listening to, press the
button again.
Pick the preset button you want
for that channel. Press and hold
the button until you hear a beep.
Repeat steps 2 to 3 to store the
first six channels.
You can store up to 12
preset channels using the six preset
buttons. Each button stores one
channel from the XM1 band and one
channel from the XM2 band.
To store a channel:
To store a channel:
Press the SAT Radio button until
XM1 or XM2 appears in the
display.
Once a channel is stored, simply
press and release the proper preset
button to tune to it.
Press the SAT Radio button again.
The available XM band will show.
Store the next six channels using
steps 2 through 3.
The presets will be lost if your car’s
battery goes dead, is disconnected,
or the radio fuse is removed.
In the category mode, only channels
within that category can be selected.
In the channel mode, all channels
can be selected.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
1.
2.
3.
4.
5.
CONTINUED
Audio System
Comfort and Convenience Features
SCAN
Preset
175
You will have to store your favorite
stations in the Preset buttons after
the system begins working. Your
original settings were lost when
power was disconnected.
Your car’s audio system will disable
itself if it is disconnected from
electrical power for any reason. To
make it work again, the user must
enter a specific five-digit code in the
Preset buttons. Because there are
hundreds of number combinations
possible from five digits, making the
system work without knowing the
exact code is nearly impossible.
You should have received a card that
lists your audio system’s code
number and serial number. It is best
to store this card in a safe place at
home. In addition, you should write
the audio system’s serial number in
this Owner’s Manual. If you should
happen to lose the card, you must
obtain the code number from your
Acura dealer. To do this, you will
need the system’s serial number.
If you make a mistake entering the
code, do not start over or try to
correct your mistake. Complete the
five-digit sequence, then enter the
correct code. You have three tries to
enter the correct code. If you are
unsuccessful in three attempts, you
must then leave the system on for
one hour before trying again.
If your car’s battery is disconnected
or goes dead, or the radio fuse is
removed, the audio system will
disable itself. If this happens, you
will see ‘‘
’’ in the frequency
display the next time you turn on the
system. Use the Preset buttons to
enter the five-digit code. If it is
entered correctly, the radio will start
playing.
Theft Protection
Audio System
Comfort and Convenience Features
180
Turn the ignition switch to ON (II).
Turn on the headlights and check
their brightness. If the headlights
are very dim or don’t light at all,
the battery is discharged. See
on page
.
Turn the ignition switch to START
(III). If the headlights do not dim,
check the condition of the fuses. If
the fuses are OK, there is proba-
bly something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. (See
on page
.)
Do you have fuel? Turn the
ignition switch to ON (II) for a
minute and watch the fuel gauge.
The low fuel level warning light
may not be working, so you were
not reminded to fill the tank.
There may be an electrical
problem, such as no power to the
fuel pump. Check all the fuses
(see page
).
If you find nothing wrong, you will
need a qualified technician to find
the problem. See
on page
.
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is dis-
charged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page
). You can
then try jump starting the vehicle
from a booster battery (see page
).
Are you using the proper starting
procedure? Refer to
on page
.
In this case, the starter motor’s
speed sounds normal, or even faster
than normal, when you turn the
ignition switch to START (III), but
the engine does not run.
316
332
272
316
217
328
332
If Your Engine Won’t Start
Taking Care of the Unexpected
Jump Starting
Emergency Towing
Emergency
Towing
Starting the
Engine
The Starter Operates Normally
315
If the electric motor will not close
the moonroof, do the following:
Check the fuse for the moonroof
motor (see page
). If the fuse
is blown, replace it with one of the
same or lower rating.
Try closing the moonroof. If the
new fuse blows immediately or the
moonroof motor still does not
operate, you can close the
moonroof manually.
Insert the moonroof wrench into
the socket behind this plug. Turn
the wrench until the moonroof is
fully closed.
Remove the lens from the rear
ceiling light (see page
).
Get the moonroof wrench out of
the tool kit in the trunk.
Remove the plug in the center of
the rear ceiling light.
Remove the wrench. Reinstall the
plug and lens.
1.
2.
3.
4.
5.
6.
7.
328
295
Closing the Moonroof
Taking Care of the Unexpected
326
PLUG
SOCKET
The under-hood fuse box is located
in the engine compartment next to
the battery. To open it, push the tab
as shown.
The interior fuse box is underneath
the dashboard on the driver’s side.
To open it, turn the knob as shown.
All the electrical circuits in your car
have fuses to protect them from a
short circuit or overload. These
fuses are located in two fuse boxes.
Fuses
Taking Care of the Unexpected
327
INTERIOR
KNOB
UNDER-HOOD
TAB
Check each of the large fuses in
the under-hood fuse box by
looking through the top at the wire
inside. Removing these fuses
requires a Phillips-head screw-
driver.
Check the smaller fuses in the
under-hood fuse box and all the
fuses in the interior fuse box by
pulling out each fuse with the fuse
puller provided in the door of the
interior fuse box.
Remove the cover from the fuse
box.
Turn the ignition switch to LOCK
(0). Make sure the headlights and
all other accessories are off.
If something electrical in your car
stops working, the first thing you
should check for is a blown fuse.
Determine from the chart on pages
and
, or the diagram on the
fuse box lid, which fuse or fuses
control that component. Check those
fuses first, but check all the fuses
before deciding that a blown fuse is
not the cause. Replace any blown
fuses and check the component’s
operation.
3.
1.
2.
4.
330
331
Checking and Replacing Fuses
Fuses
Taking Care of the Unexpected
328
FUSE
BLOWN
FUSE
PULLER
Look for a burned wire inside the
fuse. If it is burned, replace it with
one of the spare fuses of the same
rating or lower.
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem in your car.
Leave the blown fuse in that
circuit and have your car checked
by a qualified mechanic.
If you cannot drive the vehicle
without fixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
from one of the other circuits. Make
sure you can do without that circuit
temporarily (such as the cigarette
lighter or radio).
If you replace the blown fuse with a
spare fuse that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
fuse with one of the correct rating as
soon as you can.
If the radio fuse is removed, the
audio system will disable itself. The
next time you turn on the radio you
will see ‘‘
’’ in the frequency
display. Use the Preset buttons to
enter the five-digit code (see page
).
5.
6.
180
CONTINUED
Fuses
Taking Care of the Unexpected
329
BLOWN
Replacing a fuse with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a replace-
ment fuse with the proper rating for the
circuit, install one with a lower rating.
ʵ
No.
Amps.
No.
Amps.
Circuits Protected
Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
20 A
10 A
20 A
15 A
20 A
20 A
20 A
20 A
20 A
10 A
10 A
20 A
30 A
30 A
16
17
18
19
20
21
22
23
24
25
26
27
28
20 A
20 A
15 A
7.5 A
20 A
30 A
50 A
40 A
40 A
120 A
40 A
40 A
50 A
Front Fog Light
ETS (Electrical Tilt/
Telescope Steering)
Meter
Back-up, Radio
Interior Lights
Wiper Motor
Ignition Switch
Power Window
Heater Motor
Battery
VSA Motor
Rear Window Defogger
Fuse box
Not Used
Brake, Horn
Hazard
Driver Power Window
TCS
VSA
Power Door Lock
Right Headlight Low
Left Headlight Low
Cooling Fan
Left Headlight High
Right Headlight High
Condenser Fan
Moonroof
Front Passenger’s Power
Seat
Fuses
Taking Care of the Unexpected
330
UNDER-HOOD FUSE BOX
ʵ
ʵ
ˎ
ˎ
ˎ
No.
Amps.
Circuits Protected
Circuits Protected
No.
Amps.
14
15
16
17
18
19
20
21
22
23
24
25
26
7.5 A
7.5 A
10 A
7.5 A
20 A
7.5 A
20 A
20 A
20 A
7.5 A
20 A
30 A
Starter Signal
ACG
ACC Socket
Power Window MPCS
Front Right Power Window
Mirror
ECU (Body)
Rear Left Power Window
Fuel Pump
SRS
Rear Right Power Window
Ignition Coils
Not Used
Small Light
Not Used (OP)
Condenser Fan Relay,
Cooling Fan Relay
ACC, Radio
A/C Clutch, Front Heated
Seat
ECU (PCM)
SRS
Driver’s Power Seat
Reclining/Rear Height/
Power Lumber
Bose Audio System
Daytime Running Lights
Driver’s Power Seat Slide/
Front Height
Daytime Running Lights
Meter, Moonroof
1
2
3
4
5
6
7
8
9
10
11
12
13
15 A
7.5 A
10 A
20 A
20 A
10 A
20 A
20 A
10 A
20 A
7.5 A
7.5 A
On Canadian models
1 :
1
1
Fuses
Taking Care of the Unexpected
331
INTERIOR FUSE BOX
ʵ
ˎ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ʵ
ˎ
Technical Information
Specifications
339
Engine
Alignment
Tires
Battery
Fuses
Lights
12 V
12 V
55 W (H1) (High beam)
27/8 W
3.54 x 3.58 in (90 x 91 mm)
212 cu-in (3,474 cm
)
9.6 : 1
0.00 in (0.0 mm)
0.08 in (2.0 mm)
0°30’
2°50’
P225/55R16 94V
T135/80D16 101M
30 psi (210 kPa , 2.1 kgf/cm
)
60 psi (420 kPa , 4.2 kgf/cm
)
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
21 W
21/5 W
55 W (H1)
21 W
3 CP
21 W
3 CP
5 W
5 W
3.4 W
3.4 W
2 W
Type
Bore x Stroke
Displacement
Compression ratio
Spark plugs
Water cooled 4-stroke
SOHC V-6 gasoline engine
Toe
Camber
Caster
Size
Pressure
Capacity
12 V
55 AH/5 HR
Interior
Under-hood
65 AH/20 HR
12 V
See page
331
or the fuse label
attached to the inside of the fuse
box door under the dashboard.
See page
330
or the fuse box
cover.
See spark plug maintenance
section page
272
.
Headlights
Front turn signal/parking lights
Rear turn signal lights
Brake/Taillights
Front fog lights
High-mount brake light
Front side marker lights
Back-up lights
License plate lights
Ceiling lights
Trunk light
Door courtesy lights
Vanity mirror light
Front
Rear
Front
Rear
Front
Front/Rear
Spare
Front/Rear
Spare
in
Front
Rear
Low beam headlight bulbs are a type of high voltage discharge
tube (D2R).
1 :
1