Saturn Outlook - 2010 Fuse Box Diagram

Saturn Outlook - 2010 Fuse Box Diagram

2-14
Keys, Doors and Windows
3.
Get out of the vehicle, close the
door and wait for the security
light to go out.
4.
Then reach in through the
window, unlock the door with the
manual door lock and open the
door. This should set off the
alarm.
If the alarm does not sound when it
should, but the vehicle's headlamps
flash, check to see if the horn
works. The horn fuse may be blown.
To replace the fuse, see
Fuses and
Circuit Breakers on page 10
31
.
If the alarm does not sound or the
vehicle's headlamps do not flash,
see your dealer/retailer for service.
Immobilizer
See
Radio Frequency Statement
on
page 13
16
for information regarding
Part 15 of the Federal
Communications Commission (FCC)
Rules and RSS-210/211 of Industry
and Science Canada.
Immobilizer Operation
This vehicle has PASS-Key
®
III+
(Personalized Automotive Security
System) theft-deterrent system.
PASS-Key
®
III+ is a passive
theft-deterrent system.
The system is automatically armed
when the key is removed from the
ignition.
The system is automatically
disarmed when the key is turned to
ON/RUN, ACC/ACCESSORY or
START from the LOCK/OFF
position.
You do not have to manually arm or
disarm the system.
The security light comes on if there
is a problem with arming or
disarming the theft-deterrent
system.
When the PASS-Key
®
III+ system
senses an incorrect key, the vehicle
does not start. Anyone using a
trial-and-error method to start the
vehicle will be discouraged because
of the high number of electrical key
codes.
If the engine does not start and the
security light on the instrument
panel comes on when trying to start
the vehicle, there may be a problem
with your theft-deterrent system.
Turn the ignition off and try again.
If the engine still does not start, and
the key appears to be undamaged,
try another ignition key and check
the fuses. See
Fuses and Circuit
Breakers
on page 10
31
for
additional information. If the engine
still does not start with the other key,
the vehicle needs service. If the
vehicle does start, the first key may
be faulty. See your dealer/retailer
who can service the PASS-Key
®
III+
to have a new key made. In an
emergency, contact Roadside
Assistance. See
Roadside
Assistance Program on page 13
5
.
It is possible for the PASS-Key
®
III+
decoder to learn the transponder
value of a new or replacement key.
Instruments and Controls
5-9
5.
To decrease the time or date, do
one of the following:
.
Press
©
SEEK.
.
Press
s
REV.
.
Turn
f
counter-clockwise.
To change the time default setting
from 12 hour to 24 hour or to
change the date default setting from
month/day/year to day/month/year:
1.
Press
G
and then the
pushbutton located under the
forward arrow that displays on
the radio screen until the time
12H (hour) and 24H (hour), and
the date MM/DD (month and
day) and DD/MM (day and
month) displays.
2.
Press the pushbutton located
under the desired option.
3.
Press
G
again to apply the
selected default, or let the
screen time out.
Power Outlets
The vehicle has three 12-volt outlets
which can be used to plug in
electrical equipment, such as a
cellular telephone, a compact disc
player, etc.
The power outlets are located on
the instrument panel below the
climate controls, at the rear of the
center console, and in the rear
cargo area. Lift the cover to access
the outlet. Close the cover when not
using the outlet.
Notice:
Leaving electrical
equipment plugged in for an
extended period of time while the
vehicle is off will drain the
battery. Power is always supplied
to the outlets. Always unplug
electrical equipment when not in
use and do not plug in equipment
that exceeds the maximum
20 ampere rating.
Certain accessory plugs may not be
compatible to the accessory power
outlet and could result in blown
vehicle and adapter fuses. If a
problem is experienced, see your
dealer/retailer for additional
information on the power accessory
outlets.
Notice:
Adding any electrical
equipment to the vehicle can
damage it or keep other
components from working as
they should. The repairs would
not be covered by the vehicle
warranty. Do not use equipment
exceeding maximum amperage
rating of 20 amperes. Check with
your dealer/retailer before adding
electrical equipment.
6-4
Lighting
If the ignition is turned off with the
exterior lamp control in the parking
lamps or headlamps position, the
delayed headlamps cycle will not
occur.
To disable the delayed headlamps
feature or change the time of delay,
see
Vehicle Personalization (With
DIC Buttons) on page 5
42
.
Hazard Warning Flashers
|
Hazard Warning Flasher:
Press this button located on the
instrument panel below the audio
system, to make the front and rear
turn signal lamps flash on and off.
This warns others that you are
having trouble. Press again to turn
the flashers off.
The turn signals do not work while
the hazard warning flashers are on.
Turn and Lane-Change
Signals
An arrow on the instrument panel
cluster flashes in the direction of the
turn or lane change.
Move the lever all the way up or
down to signal a turn.
Raise or lower the lever until the
arrow starts to flash to signal a lane
change. Hold it there until the lane
change is completed. If the lever is
briefly pressed and released, the
turn signal flashes three times.
The lever returns to its starting
position whenever it is released.
If after signaling a turn or lane
change the arrow flashes rapidly or
does not come on, a signal bulb
might be burned out.
Have the bulbs replaced. If the bulb
is not burned out, check the fuse.
See
Fuses and Circuit Breakers
on
page 10
31
.
Turn Signal On Chime
If either one of the turn signals are
left on and the vehicle has been
driven more than 3/4 mile (1.2 km), a
chime will sound.
Driving and Operating
9-53
Trailer Wiring Harness
Basic Trailer Wiring
The trailer wiring harness, with a
seven-pin connector, is located at
the rear of the vehicle and is tied to
the vehicle's frame. The harness
connector can be plugged into a
seven-pin universal heavy-duty
trailer connector available through
your dealer/retailer.
The seven-wire harness contains
the following trailer circuits:
.
Yellow: Left Stop/Turn Signal
.
Dark Green: Right Stop/Turn
Signal
.
Brown: Taillamps
.
Black: Ground
.
Light Green: Back-up Lamps
.
Red/Black: Battery Feed
.
Dark Blue: Trailer Brake*
*The fuse for this circuit is installed
in the underhood electrical center,
but the wires are not connected.
They should be connected by your
dealer/retailer or a qualified service
center.
If the back-up lamp circuit is not
functional, contact your dealer/
retailer.
If a remote (non-vehicle) battery is
being charged, press the Tow/Haul
mode switch located on the center
console near the climate controls.
This will boost the vehicle system
voltage and properly charge the
battery. If the trailer is too light for
Tow/Haul mode, turn on the
headlamps (Non-HID only) as a
second way to boost the vehicle
system and charge the battery.
Electric Trailer Brake Control
Wiring Provisions
These wiring provisions for an
electric trailer brake controller are
included with the vehicle as part of
the trailer wiring package. The
instrument panel contains blunt cut
wires behind the steering column for
the electric trailer brake controller.
The harness contains the following
wires:
.
Red/Black: Power Supply
.
White: Brake Switch Signal
.
Gray: Illumination
.
Dark Blue: Trailer Brake Signal
.
Black: Ground
The electric trailer brake controller
should be installed by your dealer/
retailer or a qualified service center.
Vehicle Care
10-7
A. Radiator Pressure Cap . See
Cooling System on page 10
14
.
B. Engine Coolant Recovery Cap.
See
Cooling System
on
page 10
14
.
C. Remote Negative (
) Terminal.
See
Jump Starting
on
page 10
78
.
D.
Engine Compartment Fuse
Block on page 10
31
.
E. Remote Positive (+) Terminal.
See
Jump Starting
on
page 10
78
.
F.
Power Steering Reservoir and
Cap (under engine cover). See
Power Steering Fluid
on
page 10
20
.
G. Engine Oil Fill Cap. See
When
to Add Engine Oil
under
Engine
Oil on page 10
8
.
H.
Engine Cover on page 10
7
.
I.
Engine Oil Dipstick. See
Checking Engine Oil
under
Engine Oil on page 10
8
.
J.
Automatic Transmission Fluid
Dipstick. See
Checking the
Fluid Level
under
Automatic
Transmission Fluid
on
page 10
12
.
K. Brake Master Cylinder
Reservoir. See
Brake Fluid
under
Brakes on page 10
22
.
L.
Engine Air Cleaner/Filter
on
page 10
12
.
M. Windshield Washer Fluid
Reservoir. See
Adding Washer
Fluid
under
Washer Fluid
on
page 10
21
.
Engine Cover
A. Oil Fill Cap
B. Engine Cover
To remove:
1.
Remove the oil fill cap (A).
2.
Raise the engine cover (B) to
release from the retainers.
3.
Lift and remove the engine
cover.
4.
Reverse Steps 1 through 3 to
reinstall engine cover.
10-30
Vehicle Care
Electrical System
High Voltage Devices and
Wiring
{
WARNING
Exposure to high voltage can
cause shock, burns, and even
death. The high voltage systems
in your vehicle can only be
serviced by technicians with
special training.
High voltage devices are
identified by labels. Do not
remove, open, take apart,
or modify these devices. High
voltage cable or wiring has
orange covering. Do not probe,
tamper with, cut, or modify high
voltage cable or wiring.
Electrical System
Overload
The vehicle has fuses and circuit
breakers to protect against an
electrical system overload.
When the current electrical load is
too heavy, the circuit breaker opens
and closes, protecting the circuit
until the current load returns to
normal or the problem is fixed.
This greatly reduces the chance of
circuit overload and fire caused by
electrical problems.
Fuses and circuit breakers protect
the following in the vehicle:
.
Headlamp Wiring
.
Windshield Wiper Motor
.
Power Windows and other
Power Accessories
Headlamp Wiring
An electrical overload may cause
the lamps to go on and off, or in
some cases to remain off. Have the
headlamp wiring checked right away
if the lamps go on and off or
remain off.
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected
from electrical overload, overload
due to heavy snow or ice, may
cause wiper linkage damage.
Always clear ice and heavy snow
from the windshield before using the
windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Vehicle Care
10-31
Fuses and Circuit
Breakers
The wiring circuits in your vehicle
are protected from short circuits by
a combination of fuses, circuit
breakers and fusible thermal links.
This greatly reduces the chance of
fires caused by electrical problems.
Look at the silver-colored band
inside the fuse. If the band is broken
or melted, replace the fuse. Be sure
you replace a bad fuse with a new
one of the identical size and rating.
Fuses of the same amperage can
be temporarily borrowed from
another fuse location, if a fuse goes
out. Replace the fuse as soon as
you can.
Engine Compartment
Fuse Block
The underhood fuse block is located
in the engine compartment, on the
passenger side of the vehicle.
Lift the cover for access to the fuse/
relay block.
Notice:
Spilling liquid on any
electrical components on the
vehicle may damage it. Always
keep the covers on any electrical
component.
To remove fuses, hold the end of
the fuse between your thumb and
index finger and pull straight out.
10-32
Vehicle Care
Fuses
Usage
A/C CLUTCH
Air Conditioning
Clutch
ABS MTR
Antilock Braking
System (ABS)
Motor
AFS
Adaptive Forward
Lighting System
AIRBAG
Airbag System
AUX POWER
Auxiliary Power
AUX
VAC PUMP
Auxiliary
Vacuum Pump
AWD
All-Wheel-Drive
System
BATT 1
Battery 1
BATT 2
Battery 2
BATT 3
Battery 3
ECM
Engine Control
Module
ECM 1
Engine Control
Module 1
EMISSION 1
Emission 1
Vehicle Care
10-33
Fuses
Usage
EMISSION 2
Emission 2
EVEN COILS
Even Injector Coils
FAN 1
Cooling Fan 1
FAN 2
Cooling Fan 2
FOG LAMP
Fog Lamps
FSCM
Fuel System
Control Module
HORN
Horn
HTD MIR
Heated Outside
Rearview Mirror
HVAC BLWR
Heating, Ventilation
and Air
Conditioning
Blower
LT HI BEAM
Left High-Beam
Headlamp
LT LO BEAM
Left Low-Beam
Headlamp
LT PRK
Left Parking Lamp
Fuses
Usage
LT TRLR
STOP/TRN
Trailer Left
Stoplamp and Turn
Signal
ODD COILS
Odd Injector Coils
PCM IGN
Powertrain Control
Module Ignition
PWR L/GATE
Power Liftgate
PWR
OUTLET
Power Outlet
REAR
CAMERA
Rear Camera
RR APO
Rear Accessory
Power Outlet
RR DEFOG
Rear Defogger
RR HVAC
Rear Climate
Control System
RT HI BEAM
Right High-Beam
Headlamp
RT LO BEAM
Right Low-Beam
Headlamp
Fuses
Usage
RT PRK
Right
Parking Lamp
RT TRLR
STOP/TRN
Trailer Right
Stoplamp and Turn
Signal
RVC SNSR
Regulated Voltage
Control Sensor
S/ROOF/
SUNSHADE
Sunroof
SERVICE
Service Repair
SPARE
Spare
Stop Lamps
(China Only)
Stop Lamps
(China Only)
STRTR
Starter
TCM
Transmission
Control Module
TRANS
Transmission
TRLR
BCK/UP
Trailer Back-up
Lamps
TRLR BRK
Trailer Brake
10-34
Vehicle Care
Fuses
Usage
TRLR
PRK LAMP
Trailer Parking
Lamps
TRLR PWR
Trailer Power
WPR/WSW
Windshield Wiper/
Washer
Relays
Usage
A/C
CMPRSR
CLTCH
Air Conditioning
Compressor Clutch
AUX
VAC PUMP
Auxiliary
Vacuum Pump
CRNK
Switched Power
FAN 1
Cooling Fan 1
FAN 2
Cooling Fan 2
FAN 3
Cooling Fan 3
FOG LAMP
Fog Lamps
HI BEAM
High-Beam
Headlamps
Relays
Usage
HID/
LO BEAM
High Intensity
Discharge (HID)
Low-Beam
Headlamps
HORN
Horn
IGN
Ignition Main
LT TRLR
STOP/TRN
Trailer Left
Stoplamp and Turn
Signal Lamp
PRK LAMP
Park Lamp
PWR/TRN
Powertrain
RR DEFOG
Rear Window
Defogger
RT TRLR
STOP/TRN
Trailer Right
Stoplamp and Turn
Signal Lamp
Stop Lamps
(China Only)
Stop Lamps
(China Only)
Relays
Usage
TRLR
BCK/UP
Trailer Back-up
Lamps
WPR
Windshield Wiper
WPR HI
Windshield Wiper
High Speed
Instrument Panel Fuse
Block
The instrument panel fuse block is
located under the instrument panel
on the passenger side of the
vehicle. Pull down on the cover to
access the fuse block.
Vehicle Care
10-35
Fuse Side
Fuses
Usage
AIRBAG
Airbag
AMP
Amplifier
BCK/
UP/STOP
Back-up Lamp/
Stoplamp
BCM
Body Control
Module
CNSTR/
VENT
Canister Vent
CTSY
Courtesy
DR/LCK
Door Locks
DRL
Daytime Running
Lamps
DRL 2
GMC HID Only/
Rear Fog
Lamps-China Only
DSPLY
Display
FRT/WSW
Front Windshield
Washer
HTD/
COOL SEAT
Heated/Cooling
Seats
Fuses
Usage
HVAC
Heating, Ventilation
and Air
Conditioning
INADV/
PWR/LED
Inadvertent
Power LED
INFOTMNT
Infotainment
LT/TRN/SIG
Driver Side Turn
Signal
MSM
Memory Seat
Module
PDM
Power Mirrors,
Liftgate Release
PWR MODE
Power Mode
PWR/MIR
Power Mirrors
RDO
Radio
REAR WPR
Rear Wiper
RT/TRN/SIG
Passenger Side
Turn Signal
SPARE
Spare
STR/WHL/
ILLUM
Steering Wheel
Illumination
10-84
Vehicle Care
Dinghy Towing
If the vehicle is front-wheel-drive, it
can be dinghy towed from the front.
These vehicles may also be towed
by putting the front wheels on a
dolly. See
Dolly Towing
later in this
section.
If the vehicle is all-wheel-drive, it
can be dinghy towed from the front.
These vehicles can also be towed
by placing them on a platform trailer
with all four wheels off of the
ground. These vehicles cannot be
towed using a dolly.
For vehicles being dinghy towed,
the vehicle should be run at the
beginning of each day and at each
RV fuel stop for about five minutes.
This will ensure proper lubrication of
transmission components. Re-install
the fuse to start the vehicle.
To tow the vehicle from the front
with all four wheels on the ground:
1.
Position the vehicle to be towed,
shift the transmission to
P (Park), and turn the ignition to
LOCK/OFF.
2.
Secure the vehicle to the towing
vehicle.
3.
Set the parking brake.
4.
Turn the ignition to ACC/
ACCESSORY.
5.
Shift the transmission to
N (Neutral).
6.
To prevent the battery from
draining while the vehicle is
being towed, remove the 50 amp
BATT1 fuse from the underhood
fuse block and store in a safe
location. See
Engine
Compartment Fuse Block
on
page 10
31
.
7.
Release the parking brake.
Notice:
If the vehicle is towed
without performing each of the
steps listed under
Dinghy
Towing,
the automatic
transmission could be damaged.
Be sure to follow all steps of the
dinghy towing procedure prior to
and after towing the vehicle.
Notice:
If 105 km/h (65 mph) is
exceeded while towing the
vehicle, it could be damaged.
Never exceed 105 km/h (65 mph)
while towing the vehicle.
Vehicle Care
10-85
Once the destination is reached:
1.
Set the parking brake.
2.
Reinstall the 50 amp BATT1 fuse
to the underhood fuse block.
3.
Shift the transmission to
P (Park), turn the ignition to
LOCK/OFF and remove the key
from the ignition.
4.
Disconnect the vehicle from the
towing vehicle.
Notice:
Do not tow a vehicle with
the front drive wheels on the
ground if one of the front tires is
a compact spare tire. Towing with
two different tire sizes on the
front of the vehicle can cause
severe damage to the
transmission.
Dolly Towing (All-Wheel-Drive
Vehicles)
All-wheel-drive vehicles must not be
towed with two wheels on the
ground. To properly tow these
vehicles, they should be placed on
a platform trailer with all four wheels
off of the ground or dinghy towed
from the front.
Dolly Towing
(Front-Wheel-Drive
Vehicles Only)
To tow a front-wheel-drive vehicle
from the front with two wheels on
the ground:
1.
Put the front wheels on a dolly.
2.
Move the shift lever to P (Park).
3.
Set the parking brake.