Saturn Outlook - 2009 Fuse Box Diagram

Saturn Outlook - 2009 Fuse Box Diagram

Safety Warnings and
Symbols
A circle with a slash through it is a
safety symbol which means “Do
Not,” “Do not do this” or “Do not let
this happen.”
A box with the word CAUTION is
used to tell about things that
could hurt you or others if you were
to ignore the warning.
{
CAUTION
These mean there is something
that could hurt you or other people.
Cautions tell what the hazard is and
what to do to avoid or reduce the
hazard. Read these cautions.
A notice tells about something that
can damage the vehicle.
Notice:
These mean there is
something that could damage
your vehicle.
Many times, this damage would not
be covered by the vehicle’s
warranty, and it could be costly. The
notice tells what to do to help
avoid the damage.
There are also warning labels on
the vehicle which use the same
words, CAUTION or Notice.
Vehicle Symbols
The vehicle has components and
labels that use symbols instead
of text. Symbols are shown along
with the text describing the operation
or information relating to a specific
component, control, message,
gage, or indicator.
M
:
This symbol is shown when
you need to see your owner manual
for additional instructions or
information.
*
:
This symbol is shown when
you need to see a service manual
for additional instructions or
information.
Preface
iii
Vehicle Symbol Chart
Here are some additional symbols
that may be found on the vehicle
and what they mean. For more
information on the symbol, refer to
the index.
9
:
Airbag Readiness Light
#
:
Air Conditioning
!
:
Antilock Brake System (ABS)
g
:
Audio Steering Wheel
Controls or OnStar
®
$
:
Brake System Warning Light
"
:
Charging System
I
:
Cruise Control
B
:
Engine Coolant Temperature
O
:
Exterior Lamps
#
:
Fog Lamps
.
:
Fuel Gage
+
:
Fuses
i
:
Headlamp High/Low-Beam
Changer
j
:
LATCH System Child Restraints
*
:
Malfunction Indicator Lamp
:
:
Oil Pressure
g
:
Outside Power Foldaway
Mirrors
}
:
Power
/
:
Remote Vehicle Start
>
:
Safety Belt Reminders
7
:
Tire Pressure Monitor
_
:
Tow/Haul Mode
F
:
Traction Control
M
:
Windshield Washer Fluid
iv
Preface
When the door is closed, the
security light stops flashing and
stays on solid for approximately
30 seconds. The content theft
deterrent alarm is not armed until
the security light goes off.
If the delayed locking feature is
active, the alarm is not activated
until all doors are closed and the
security light goes off.
Press
Q
when the driver door is
closed. The security light comes
on solid for approximately
30 seconds and then goes off.
The content theft deterrent alarm
is not armed until the security light
goes off.
The theft-deterrent system will not
activate if the doors are locked
with the vehicle’s key or the manual
door lock.
If a locked door is opened
without using the RKE transmitter,
a ten second pre-alarm occurs.
The horn chirps and the lights flash.
If the key is not placed in the
ignition and turned to START or the
door is not unlocked by pressing
Q
during the ten second pre-alarm, the
alarm goes off. The headlamps flash
and the horn sounds for about
two minutes, then turns off to save
the battery power.
The vehicle can be started with the
correct ignition key if the alarm
has been set off.
To avoid setting off the alarm by
accident:
Lock the vehicle with the door
key after the doors are closed.
Unlock the door with the RKE
transmitter. Unlocking a door
any other way sets off the alarm
if the system has been armed.
Press
K
or place the key in
the ignition and turn it to START to
turn off the alarm.
Testing the Alarm
To test the alarm:
1. From inside the vehicle, lower the
driver side window and open the
driver door.
2. Press
Q
.
3. Get out of the vehicle, close the
door and wait for the security
light to go out.
4. Then reach in through the
window, unlock the door with
the manual door lock and open
the door. This should set off
the alarm.
If the alarm does not sound when it
should, but the vehicle’s headlamps
flash, check to see if the horn
works. The horn fuse may be blown.
To replace the fuse, see
Fuses
and Circuit Breakers on page 5-92
.
If the alarm does not sound or the
vehicle’s headlamps do not flash,
see your dealer/retailer for service.
Features and Controls
2-17
If the engine does not start and the
security light on the instrument panel
comes on when trying to start the
vehicle, there may be a problem with
your theft-deterrent system. Turn the
ignition off and try again.
If the engine still does not start, and
the key appears to be undamaged,
try another ignition key and check
the fuses. See
Fuses and Circuit
Breakers on page 5-92
. If the engine
still does not start with the other
key, the vehicle needs service. If the
vehicle does start, the first key may
be faulty. See your dealer/retailer
who can service the PASS-Key
®
III+
to have a new key made. In an
emergency, contact Roadside
Assistance. See
Roadside
Assistance Program on page 7-6
.
It is possible for the PASS-Key
®
III+
decoder to learn the transponder
value of a new or replacement key.
Up to 10 keys may be programmed
to the vehicle. The following
procedure is for programming
additional keys only. If all the
currently programmed keys are lost
or do not operate, you must see
your dealer/retailer or a locksmith
who can service PASS-Key
®
III+ to
have keys made and programmed
to the system.
See your dealer/retailer or a
locksmith who can service
PASS-Key
®
III+ to get a new key
blank that is cut exactly as the
ignition key that operates the
system.
To program the new key:
1. Verify that the new key has
a
1
stamped on it.
2. Insert the already programmed
key in the ignition and start the
engine. If the engine does not
start, see your dealer/retailer for
service.
3. After the engine has started,
turn the key to LOCK/OFF,
and remove the key.
4. Insert the key to be programmed
and turn it to the ON/RUN
position within five seconds of
the original key being turned
to the LOCK/OFF position.
The security light turns off once
the key has been programmed.
5. Repeat Steps 1 through 4
if additional keys are to be
programmed.
If the PASS-Key
®
III+ key is lost or
damaged, see your dealer/retailer or
a locksmith to have a new key made.
The SERVICE THEFT DETERRENT
SYSTEM message displays on
the Driver Information Center (DIC)
when there is a problem with the
theft-deterrent system. See
DIC
Warnings and Messages on
page 3-56
for additional information.
Do not leave the key or device
that disarms or deactivates the theft
deterrent system in the vehicle.
Features and Controls
2-19
Accessory Power
Outlet(s)
The vehicle has three 12-volt
outlets which can be used to plug
in electrical equipment, such as a
cellular telephone, a compact disc
player, etc.
The power outlets are located on the
instrument panel below the climate
controls, at the rear of the center
console, and in the rear cargo area.
Lift the cover to access the outlet.
Close the cover when not using the
outlet.
Notice:
Leaving electrical
equipment plugged in for an
extended period of time while
the vehicle is off will drain
the battery. Power is always
supplied to the outlets. Always
unplug electrical equipment when
not in use and do not plug in
equipment that exceeds the
maximum 20 ampere rating.
Certain accessory plugs may
not be compatible to the accessory
power outlet and could result in
blown vehicle and adapter fuses.
If a problem is experienced, see
your dealer/retailer for additional
information on the power accessory
outlets.
Notice:
Adding any electrical
equipment to the vehicle can
damage it or keep other
components from working as
they should. The repairs would
not be covered by the vehicle
warranty. Do not use equipment
exceeding maximum amperage
rating of 20 amperes. Check
with your dealer/retailer before
adding electrical equipment.
When adding electrical equipment,
be sure to follow the proper
installation instructions included
with the equipment.
Notice:
Improper use of the
power outlet can cause damage
not covered by the warranty.
Do not hang any type of
accessory or accessory bracket
from the plug because the
power outlets are designed for
accessory power plugs only.
Instrument Panel
3-17
ground. Dolly towing is towing the
vehicle with two wheels on the
ground and two wheels up on a
device known as a dolly.
Here are some important things to
consider before recreational vehicle
towing:
What is the towing capacity of the
towing vehicle? Be sure to read
the tow vehicle manufacturer’s
recommendations.
What is the distance that will be
travelled? Some vehicles have
restrictions on how far and how
long they can tow.
Is the proper towing equipment
going to be used? See your
dealer/retailer or trailering
professional for additional advice
and equipment recommendations.
Is the vehicle ready to be towed?
Just as preparing the vehicle for a
long trip, make sure the vehicle is
prepared to be towed. See
Before
Leaving on a Long Trip on
page 4-13
.
Dinghy Towing
If the vehicle is front-wheel-drive, it
can be dinghy towed from the
front. These vehicles may also be
towed by putting the front wheels on
a dolly. See “Dolly Towing” later
in this section.
If the vehicle is all-wheel-drive, it can
be dinghy towed from the front.
These vehicles can also be towed by
placing them on a platform trailer
with all four wheels off of the ground.
These vehicles cannot be towed
using a dolly.
For vehicles being dinghy towed, the
vehicle should be run at the
beginning of each day and at each
RV fuel stop for about five minutes.
This will ensure proper lubrication of
transmission components. Re-install
the fuse to start the vehicle.
To tow the vehicle from the front
with all four wheels on the ground:
1. Position the vehicle to tow
and then secure it to the towing
vehicle.
2. Shift the transmission to P (Park)
and turn the ignition to
LOCK/OFF.
3. Set the parking brake.
4. Turn the ignition to
ACC/ACCESSORY.
5. Shift the transmission to
N (Neutral).
Driving Your Vehicle
4-23
6. To prevent the battery from
draining while the vehicle is being
towed, remove the 50 amp
BATT1 fuse from the underhood
fuse block and store in a safe
location. See
Underhood
Fuse Block on page 5-94
.
7. Release the parking brake.
Notice:
If the vehicle is towed
without performing each of
the steps listed under “Dinghy
Towing,” the automatic
transmission could be damaged.
Be sure to follow all steps of
the dinghy towing procedure prior
to and after towing the vehicle.
Notice:
If 65 mph (105 km/h)
is exceeded while towing
the vehicle, it could be damaged.
Never exceed 65 mph (105 km/h)
while towing the vehicle.
Once the destination is reached:
1. Set the parking brake.
2. Reinstall the 50 amp BATT1 fuse
to the underhood fuse block.
3. Shift the transmission to
P (Park), turn the ignition
to LOCK/OFF and remove the
key from the ignition.
4. Disconnect the vehicle from the
towing vehicle.
Notice:
Do not tow a vehicle
with the front drive wheels on the
ground if one of the front tires
is a compact spare tire. Towing
with two different tire sizes on the
front of the vehicle can cause
severe damage to the
transmission.
Dolly Towing (All-Wheel-Drive
Vehicles)
All-wheel-drive vehicles must not be
towed with two wheels on the
ground. To properly tow these
vehicles, they should be placed on
a platform trailer with all four
wheels off of the ground or dinghy
towed from the front.
4-24
Driving Your Vehicle
The seven-wire harness contains
the following trailer circuits:
Yellow: Left Stop/Turn Signal
Dark Green: Right Stop/Turn
Signal
Brown: Taillamps
Black: Ground
Light Green: Back-up Lamps
Red/Black: Battery Feed
Dark Blue: Trailer Brake*
*The fuse for this circuit is installed
in the underhood electrical center,
but the wires are not connected.
They should be connected by your
dealer/retailer or a qualified
service center.
If the back-up lamp circuit is not
functional, contact your
dealer/retailer.
If a remote (non-vehicle) battery is
being charged, press the Tow/Haul
mode switch located on the
center console near the climate
controls. This will boost the vehicle
system voltage and properly
charge the battery. If the trailer is
too light for Tow/Haul mode, turn on
the headlamps (Non-HID only) as
a second way to boost the
vehicle system and charge the
battery.
Electric Trailer Brake Control
Wiring Provisions
These wiring provisions for an
electric trailer brake controller are
included with the vehicle as
part of the trailer wiring package.
The instrument panel contains blunt
cut wires behind the steering
column for the electric trailer brake
controller. The harness contains
the following wires:
Red/Black: Power Supply
White: Brake Switch Signal
Gray: Illumination
Dark Blue: Trailer Brake Signal
Black: Ground
The electric trailer brake controller
should be installed by your
dealer/retailer or a qualified service
center.
Engine Cooling When Trailer
Towing
The cooling system may temporarily
overheat during severe operating
conditions. See
Engine Overheating
on page 5-23
.
Driving Your Vehicle
4-35
A. Radiator Pressure Cap. See
Cooling System on page 5-19
.
B. Engine Coolant Recovery Cap.
See
Cooling System on
page 5-19
.
C. Remote Negative (
) Terminal.
See
Jump Starting on page 5-30
.
D.
Underhood Fuse Block on
page 5-94
.
E. Remote Positive (+) Terminal.
See
Jump Starting on page 5-30
.
F.
Power Steering Fluid on
page 5-25
.
G. Engine Oil Fill Cap. See “When
to Add Engine Oil” under
Engine
Oil on page 5-13
.
H. Engine Oil Dipstick. See
“Checking Engine Oil” under
Engine Oil on page 5-13
.
I. Automatic Transmission Fluid
Dipstick. See “Checking the
Fluid Level” under
Automatic
Transmission Fluid on page 5-18
.
J. Brake Master Cylinder Reservoir.
See “Brake Fluid” under
Brakes
on page 5-27
.
K.
Engine Air Cleaner/Filter on
page 5-17
.
L. Windshield Washer Fluid
Reservoir. See “Adding Washer
Fluid” under
Windshield
Washer Fluid on page 5-26
.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine
oil level at each fuel fill. In order to
get an accurate reading, the oil must
be warm and the vehicle must be on
level ground.
The engine oil dipstick handle
is a yellow loop. See
Engine
Compartment Overview on
page 5-12
for the location of the
engine oil dipstick.
1. Turn off the engine and give the
oil several minutes to drain back
into the oil pan. If this is not done,
the oil dipstick might not show the
actual level.
2. Pull out the dipstick and clean
it with a paper towel or cloth,
then push it back in all the way.
Remove it again, keeping the
tip down, and check the level.
Service and Appearance Care
5-13
Add-On Electrical
Equipment
Notice:
Do not add anything
electrical to the vehicle unless you
check with your dealer/retailer
first. Some electrical equipment
can damage the vehicle and the
damage would not be covered by
the vehicle’s warranty. Some
add-on electrical equipment can
keep other components from
working as they should.
Add-on equipment can drain the
vehicle’s battery, even if the vehicle
is not operating.
The vehicle has an airbag system.
Before attempting to add anything
electrical to the vehicle, see
Servicing Your Airbag-Equipped
Vehicle on page 1-60
.
Windshield Wiper Fuses
The windshield wiper motor is
protected by a circuit breaker and a
fuse. If the motor overheats due to
heavy snow or ice, the wiper will stop
until the motor cools. If the overload
is caused by some electrical
problem, have it fixed.
Power Windows and
Other Power Options
Circuit breakers in the fuse block
protect the power windows and
other power accessories. When the
current load is too heavy, the
circuit breaker opens and closes,
protecting the circuit until the
problem is fixed or goes away.
Fuses and Circuit
Breakers
The wiring circuits in your vehicle are
protected from short circuits by a
combination of fuses, circuit breakers
and fusible thermal links. This greatly
reduces the chance of fires caused
by electrical problems.
Look at the silver-colored band
inside the fuse. If the band is broken
or melted, replace the fuse. Be sure
you replace a bad fuse with a new
one of the identical size and rating.
Fuses of the same amperage can be
temporarily borrowed from another
fuse location, if a fuse goes out.
Replace the fuse as soon as
you can.
Instrument Panel Fuse
Block
The instrument panel fuse block is
located under the instrument panel
on the passenger side of the vehicle.
Pull down on the cover to access the
fuse block.
5-92
Service and Appearance Care
Fuses
Usage
AIRBAG
Airbag
AMP
Amplifier
BCK/UP/
STOP
Back-up
Lamp/Stoplamp
BCM
Body Control
Module
CNSTR/
VENT
Canister Vent
CTSY
Courtesy
DR/LCK
Door Locks
DRL
Daytime Running
Lamps
DRL 2
GMC HID
Only/Rear Fog
Lamps-China Only
DSPLY
Display
FRT/WSW
Front Windshield
Washer
HTD/COOL
SEAT
Heated/Cooling
Seats
HVAC
Heating, Ventilation
and Air Conditioning
Fuses
Usage
IADV/PWR/
LED
Inadvertent
Power LED
INFOTMNT
Infotainment
LT/TRN/SIG
Driver Side Turn
Signal
MSM
Memory Seat
Module
PDM
Power Mirrors,
Liftgate Release
PWR
MODE
Power Mode
PWR/MIR
Power Mirrors
RDO
Radio
REAR WPR Rear Wiper
RT/TRN/SIG
Passenger Side
Turn Signal
SPARE
Spare
SPARE
Spare
STR/WHL/
ILLUM
Steering Wheel
Illumination
Fuse Side
Service and Appearance Care
5-93
Relays
Usage
LT/PWR/
SEAT
Driver Side Power
Seat Relay
RT/PWR/
SEAT
Passenger Side
Power Seat Relay
Relays
Usage
PWR/
WNDW
Power Windows
Relay
PWR/
COLUMN
Power Steering
Column Relay
L/GATE
Liftgate Relay
LCK
Power Lock Relay
REAR/WSW
Rear Window
Washer Relay
UNLCK
Power Unlock Relay
DRL2
Daytime Running
Lamps 2 Relay
LT/UNLCK
Driver Side Unlock
Relay
DRL
Daytime Running
Lamps Relay
SPARE
Spare
FRT/WSW
Front Windshield
Washer Relay
Underhood Fuse Block
The underhood fuse block is located
in the engine compartment, on
the passenger side of the vehicle.
Lift the cover for access to the
fuse/relay block.
Notice:
Spilling liquid on any
electrical components on the
vehicle may damage it. Always
keep the covers on any electrical
component.
To remove fuses, hold the end of the
fuse between your thumb and index
finger and pull straight out.
Relay Side
5-94
Service and Appearance Care
Fuses
Usage
A/C
CLUTCH
Air Conditioning
Clutch
ABS MTR
Antilock Braking
System (ABS) Motor
AFS
Adaptive Forward
Lighting System
Fuses
Usage
AIRBAG
Airbag System
AUX
POWER
Auxiliary Power
AUX VAC
PUMP
Auxiliary Vacuum
Pump
Fuses
Usage
AWD
All-Wheel-Drive
System
BATT 1
Battery 1
BATT 2
Battery 2
BATT 3
Battery 3
ECM
Engine Control
Module
ECM 1
Engine Control
Module 1
EMISSION 1 Emission 1
EMISSION 2 Emission 2
EVEN
COILS
Even Injector Coils
FAN 1
Cooling Fan 1
FAN 2
Cooling Fan 2
FOG LAMP
Fog Lamps
FSCM
Fuel System Control
Module
HORN
Horn
HTD WASH
Heated Windshield
Washer Fluid
Service and Appearance Care
5-95
Fuses
Usage
HTD MIR
Heated Outside
Rearview Mirror
HVAC
BLWR
Heating, Ventilation
and Air Conditioning
Blower
LT HI
BEAM
Left High-Beam
Headlamp
LT LO
BEAM
Left Low-Beam
Headlamp
LT PRK
Left Parking Lamp
LT TRLR
STOP/TRN
Trailer Left
Stoplamp and Turn
Signal
ODD
COILS
Odd Injector Coils
PCM IGN
Powertrain Control
Module Ignition
PWR
L/GATE
Power Liftgate
PWR
OUTLET
Power Outlet
Fuses
Usage
REAR
CAMERA
Rear Camera
RR APO
Rear Accessory
Power Outlet
RR DEFOG
Rear Defogger
RR HVAC
Rear Climate
Control System
RT HI
BEAM
Right High-Beam
Headlamp
RT LO
BEAM
Right Low-Beam
Headlamp
RT PRK
Right Parking Lamp
RT TRLR
STOP/TRN
Trailer Right
Stoplamp and Turn
Signal
RVC SNSR
Regulated Voltage
Control Sensor
S/ROOF/
SUNSHADE
Sunroof
SPARE
Spare
Fuses
Usage
Stop Lamps
(China
Only)
Stop Lamps
(China Only)
STRTR
Starter
TCM
Transmission
Control Module
TRANS
Transmission
TRLR
BCK/UP
Trailer Back-up
Lamps
TRLR BRK
Trailer Brake
TRLR PRK
LAMP
Trailer Parking
Lamps
TRLR PWR
Trailer Power
WPR/WSW
Windshield
Wiper/Washer
5-96
Service and Appearance Care