Saturn Sky - 2008 Fuse Box Diagram

Saturn Sky - 2008 Fuse Box Diagram

If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse, see
Fuses
and Circuit Breakers on page 5-94
. If the engine still
does not start with the other key, your vehicle needs
service. If your vehicle does start, the first key may be
faulty. See your dealer/retailer who can service the
PASS-Key
®
III+ to have a new key made. In an
emergency, contact Roadside Assistance. See
Roadside
Assistance Program on page 7-7
, for more information.
It may be possible for the PASS-Key
®
III+ decoder
to “learn” the transponder value of a new or replacement
key. Up to 10 keys may be programmed for the
vehicle. The following procedure is for programming
additional keys only. If all the currently programmed
keys are lost or do not operate, you must see your
dealer/retailer or a locksmith who can service
PASS-Key
®
III+ to have keys made and programmed
to the system.
See your dealer/retailer or a locksmith who can service
PASS-Key
®
III+ to get a new key blank that is cut
exactly as the ignition key that operates the system.
To program the new key:
1. Verify that the new key has a
1
stamped on it.
2. Insert the already programmed key in the ignition
and start the engine. If the engine will not start,
see your dealer/retailer for service.
3. After the engine has started, turn the key to
LOCK/OFF, and remove the key.
4. Insert the key to be programmed and turn it to the
ON/RUN position within five seconds of the original
key being turned to the LOCK/OFF position.
The security light will turn off once the key has
been programmed.
5. Repeat Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the security light comes on
and stays on, you may be able to restart your engine if
you turn it off. Your PASS-Key
®
III+ system, however,
is not working properly and must be serviced by your
dealer/retailer. Your vehicle is not protected by the
PASS-Key
®
III+ system at this time.
If you lose or damage your PASS-Key
®
III+ key, see
your dealer/retailer or a locksmith who can service
PASS-Key
®
III+ to have a new key made.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
2-15
Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will return
automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, raise or lower the lever until
the arrow starts to flash. Hold it there until you complete
your lane change. The lever will return by itself when
you release it.
As you signal a turn or a lane change, if the arrows
flash rapidly, a signal bulb may be burned out and other
drivers will not see your turn signal. If a bulb is burned
out, replace it to help avoid an accident.
If the arrows do not go on at all when you signal a turn,
check the fuse. See
Fuses and Circuit Breakers on
page 5-94
.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high
beam, push the turn signal lever away from you.
When the high beams
are on, this light on the
instrument panel cluster
will also be on.
To change the headlamps from high beam to low beam,
pull the turn signal lever toward you.
Flash-to-Pass
This feature lets you use your high-beam headlamps to
signal a driver in front of you that you want to pass.
To use it, pull the turn signal/multifunction lever toward
you until the high-beam headlamps come on, then
release the lever to turn them off.
3-8
Accessory Power Outlet(s)
The accessory power outlet can be used to connect
electrical equipment such as a cellular phone or
CB radio.
The accessory power outlet is located on the instrument
panel, to the right of the radio.
To use the outlet, remove the cover. When not in use,
always cover the outlet with the protective cap.
Notice:
Leaving electrical equipment plugged in for
an extended period of time while the vehicle is off
will drain the battery. Power is always supplied
to the outlets. Always unplug electrical equipment
when not in use and do not plug in equipment
that exceeds the maximum 20 ampere rating.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your dealer/retailer for additional
information on the accessory power outlet.
Notice:
Adding any electrical equipment to your
vehicle can damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Do not use equipment
exceeding maximum amperage rating of 20 amperes.
Check with your dealer/retailer before adding
electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
Ashtray(s) and Cigarette Lighter
Your vehicle may have a removable muffin tin ashtray
and cigarette lighter. The muffin tin ashtray can be
placed into the front console side cupholder. To use the
lighter, located on the instrument panel to the left
side of the glove box door, push it in all the way and let
go. When it is ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating does not let the lighter back away from the
heating element when it is hot. Damage from
overheating can occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
Notice:
If you put papers, pins, or other flammable
items in the ashtray, hot cigarettes or other
smoking materials could ignite them and possibly
damage your vehicle. Never put flammable items in
the ashtray.
3-16
A. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-34
.
B. Coolant Surge Tank and Pressure Cap. See
Cooling
System on page 5-28
.
C. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-35
and
Hydraulic Clutch
on page 5-23
.
D. Engine Oil Dipstick (Out of View). See “Checking
Engine Oil” under
Engine Oil on page 5-15
.
E. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-21
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-15
.
G. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-33
.
H. Remote Negative (
) Ground (Out of View).
See
Jump Starting on page 5-39
.
I. Battery (Out of View). See
Battery on page 5-38
.
J. Remote Positive (+) Terminal. See
Jump Starting on
page 5-39
.
K. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-96
.
5-13
A. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-34
.
B. Coolant Surge Tank and Pressure Cap. See
Cooling
System on page 5-28
.
C. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 5-35
and
Hydraulic Clutch
on page 5-23
.
D. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-15
.
E. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-21
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-15
.
G. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-33
.
H. Remote Negative (
) Ground (Out of View).
See
Jump Starting on page 5-39
.
I. Battery (Out of View). See
Battery on page 5-38
.
J. Remote Positive (+) Terminal. See
Jump Starting on
page 5-39
.
K. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-96
.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time you
get fuel. In order to get an accurate reading, the oil
must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop.
See
Engine Compartment Overview on page 5-12
for
the location of the engine oil dipstick.
1. Turn off the engine and give the oil several minutes
to drain back into the oil pan. If you do not do this,
the oil dipstick might not show the actual level.
2. Pull the dipstick and clean it with a paper towel or
cloth, then push it back in all the way. Remove it
again, keeping the tip down and check the level.
When to Add Engine Oil
If the oil is below the MIN (minimum) mark, add at
least one quart/liter of the recommended oil.
5-15
Notice:
If you leave your radio or other accessories
on during the jump starting procedure, they could
be damaged. The repairs would not be covered
by your warranty. Always turn off your radio and
other accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or the accessory power outlet. Turn off
the radio and all lamps that are not needed.
This will avoid sparks and help save both batteries.
And it could save the radio!
4. Open the hood on the other vehicle and locate the
positive (+) and negative (
) terminal locations on
that vehicle.
You will not need to access your battery for jump
starting. Your vehicle has a remote positive (+) and
a remote negative (
) jump starting terminal.
The remote positive (+)
terminal is located under a
red plastic cover on the
engine compartment
fuse block. Open the
red plastic cover to access
the terminal.
Do not remove fuse block cover to jump start the
vehicle.
The remote negative (
)
ground bracket is located
in the rear of the engine
compartment, on the
passenger’s side of
the vehicle, and is
marked GND (
).
5-40
Electrical System
Add-On Electrical Equipment
Notice:
Do not add anything electrical to your
vehicle unless you check with your dealer/retailer
first. Some electrical equipment can damage
your vehicle and the damage would not be covered
by your warranty. Some add-on electrical equipment
can keep other components from working as they
should.
Add-on equipment can drain your vehicle’s battery, even
if your vehicle is not operating.
Your vehicle has an airbag system. Before attempting to
add anything electrical to your vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-48
.
Headlamp Wiring
The headlamp wiring is protected by fuses in the fuse
block. An electrical overload will cause the lamps to turn
off. If this happens, have your headlamp wiring
checked right away.
Power Windows and Other Power
Options
Circuit breakers in the fuse block protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed or
goes away.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of J-Case fuses,
mini-fuses and circuit breakers. This greatly reduces the
chance of fires caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
If you ever have a problem on the road and do not have
a spare fuse, you can borrow one that has the same
amperage. Just pick some feature of your vehicle
that you can get along without – like the radio or
cigarette lighter – and use its fuse, if it is the correct
amperage. Replace it as soon as you can.
5-94
Floor Console Fuse Block
The floor console fuse block is located on the passenger
side of the vehicle under the carpet.
Remove the fuse block cover to access the fuses.
Use the fuse puller to remove fuses.
After re-installing the fuse block cover, be sure to tuck
the carpet under the heater floor outlets.
Fuses
Usage
1
Fuse Puller
2
Empty
3
Empty
4
Empty
5
Empty
6
Amplifier
7
Cluster
8
Ignition Switch, PassKey III+
9
Stoplamp
10
Climate Control System,
PassKey III+
11
Empty
12
Spare
13
Airbag
14
Spare
15
Wiper
16
Climate Control System, Automatic
Occupant Sensing Module, Crank
Relay, Instrument Panel Cluster
5-95
Fuses
Usage
1
Empty (LE5); Cooling Fan (LNF)
2
Rear Window Defogger
3
Empty
4
Body Control Module 3
5
Crank
6
Body Control Module 2
7
Body Control Module
8
Cooling Fan 2 (LE5); Empty (LNF)
9
Empty
10
Trunk
11
Trunk
12
Empty
13
Fuel Pump
14
Rear Defogger Relay
15
Air Conditioning Clutch Relay
16
Empty
17
Empty
18
Trunk Release Relay
19
Fuel Pump Relay
20
Empty
21
Mirrors
Fuses
Usage
22
Air Conditioning
23
Empty
24
Cooling Fan 2 Relay (LE5);
Empty (LNF)
25
Fuse Puller
26
Powertrain Relay
27
Empty
28
Back-up Lamps Relay
(Automatic Transmission);
Empty (Manual Transmission)
29
Data Link Connector
30
Outlet
31
Back-up Lamps
(Automatic Transmission);
Empty (Manual Transmission)
32
Empty
33
Emissions
34
Crank Relay
35
Empty
36
Empty
37
Power Seat
38
Empty
5-97
Fuses
Usage
39
Empty
40
Cooling Fan 1 (LE5); Empty (LNF)
41
Empty (LE5); Turbo,
Cam Phaser (LNF)
42
Engine Control Module
43
Engine Control Module, Transmission
44
Antilock Brake System
45
Injectors, Ignition Coils (LE5);
Ignition Coils (LNF)
46
Back-up Lamps
(Manual Transmission);
Empty (Automatic Transmission)
47
Empty
48
Daytime Running Lamps Relay
49
Daytime Running Lamps
50
Cooling Fan 1 Relay (LE5);
Empty (LNF)
51
Run/Crank Relay
52
Windshield Wiper Low/High Relay
53
Fog Lamps
54
Fog Lamps Relay
Fuses
Usage
55
Horn Relay
56
S Band, OnStar
®
, Remote Keyless
Entry System
57
Antilock Brake System
58
Wiper Diode
59
Windshield Wiper
60
Horn
61
Antilock Brake System
62
Instrument Panel Ignition
63
Driver Side High Beam
64
Canister Vent
65
Driver Side Low-Beam Headlamp
66
Passenger Side Low-Beam Headlamp
67
Passenger Side High-Beam Headlamp
68
Parking Lamps Relay
69
Parking Lamps
70
Windshield Wiper On/Off Relay
71
Low-Beam Headlamp Relay
72
High-Beam Headlamp Relay
5-98