Saturn VUE - 2007 Fuse Box Diagram

Saturn VUE - 2007 Fuse Box Diagram

Passlock
®
Your vehicle is equipped with the
Passlock
®
theft-deterrent system.
This light will come on
for the theft-deterent
system.
Passlock
®
is a passive theft-deterrent system.
Passlock
®
enables fuel if the ignition lock cylinder is
turned with a valid key. If a correct key is not used
or the ignition lock cylinder is tampered with, fuel is
disabled.
During normal operation, the security light will go
off approximately five seconds after the key is
turned to RUN following an engine start.
If the engine stalls and the security light flashes,
wait until the light stops flashing before trying
to restart the engine. Remember to release the
key from START as soon as the engine starts.
If the engine is running and the security light comes
on, you will be able to restart the engine if you turn
the engine off. However, your Passlock
®
system
is not working properly and must be serviced by
your retailer. Your vehicle is not protected by
Passlock
®
at this time. You may also want to
check the fuses, see
Fuses and Circuit Breakers
on page 409
. See your retailer for service. Also,
see
Roadside Assistance Program on page 445
for
more information.
108
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
G
Turn and Lane-Change Signals. See
Turn and Lane-Change Signals on page 143
.
O
Exterior Lamp Control. See
Headlamps on
page 149
.
2
Headlamp High/Low-Beam Changer.
See
Headlamp High/Low-Beam Changer
on page 144
.
Flash-to-Pass Feature. See
Flash-to-Pass on
page 144
.
AUTO Automatic Headlamps. See
Automatic
Headlamp System on page 151
.
Turn and Lane-Change Signals
The turn signal has one upward (for right) and
one downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will
return automatically.
An arrow on the
instrument panel
cluster will flash in the
direction of the turn
or lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete the lane change. The lever will return
by itself when you release it.
As you signal a turn or a lane change, if the
arrows flash rapidly, a signal bulb may be burned
out and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check the fuse, see
Fuses and Circuit
Breakers on page 409
and for burned-out bulbs.
143
Battery Run-Down Protection
Your vehicle is equipped with a battery saver
feature designed to protect your vehicle’s battery.
When any interior lamp is left on and the
ignition is turned off, the battery rundown
protection system will automatically turn the lamp
off after 20 minutes. This will avoid draining
the battery.
Accessory Power Outlet(s)
The accessory power outlets can be used to
connect electrical equipment such as a cellular
phone or CB radio.
The accessory power outlets are located on the
instrument panel near the climate controls, on the
rear of the center console, and also inside the
console under the cupholders.
To use the outlets, remove the cover. When not in
use, always cover the outlet with the protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always
turn off electrical equipment when not in use
and do not plug in equipment that exceeds the
maximum 20 ampere rating.
Certain electrical accessories may not be
compatible with the accessory power outlet and
could result in blown vehicle or adapter fuses.
If you experience a problem, see your retailer for
additional information on the accessory
power outlet.
Notice:
Adding any electrical equipment to
your vehicle may damage it or keep other
components from working as they should.
The repairs would not be covered by your
warranty. Check with your retailer before
adding electrical equipment.
When adding electrical equipment, be sure to
follow the installation instructions included with
the equipment.
Notice:
Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.
154
Cigarette Lighter
Your vehicle may have a cigarette lighter. To use
the lighter, located on the instrument panel below
the climate controls, push it in all the way and let
go. When it is ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it
is heating does not let the lighter back
away from the heating element when it is hot.
Damage from overheating can occur to the
lighter or heating element, or a fuse could be
blown. Do not hold a cigarette lighter in while
it is heating.
Notice:
If you put papers, pins, or other
flammable items in the ashtray, hot cigarettes
or other smoking materials could ignite
them and possibly damage your vehicle.
Never put flammable items in the ashtray.
Climate Controls
Climate Control System
With this system you can control the heating,
cooling and ventilation for your vehicle.
Operation
To change the current mode, use the right knob to
select one of the following:
H
(Vent):
This mode directs air to the instrument
panel outlets.
155
Oil Pressure Light
If you have a low
engine oil pressure
problem, this light
will stay on after you
start your engine,
or come on when you
are driving.
This indicates that your engine is not receiving
enough oil. The engine could be low on oil,
or could have some other oil problem. Have it
fixed immediately.
The oil light may also come on when the ignition
is on but the engine is not running, the light
will come on as a test to show you it is working,
but the light will go out when you turn the
ignition to START. If it does not come on with
the ignition on, you may have a problem with the
fuse or bulb. Have it fixed right away.
{
CAUTION:
Do not keep driving if the oil pressure is
low. If you do, your engine can become so
hot that it catches fire. You or others could
be burned. Check your oil as soon as
possible and have your vehicle serviced.
Notice:
Lack of proper engine oil maintenance
may damage the engine. The repairs would
not be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
178
As an example, if you initially perform the
lubrication procedure and tow your vehicle for
three hours, then park for four hours, the
lubrication procedure will need to be performed
again, prior to dinghy towing the vehicle.
Notice:
Towing your vehicle after shifting the
automatic transaxle (four-speed or five-speed)
from anything other than DRIVE (D) to
NEUTRAL (N) can cause internal damage to
the automatic transaxle. Always shift the
automatic transaxle (four-speed or five-speed)
from DRIVE (D) to NEUTRAL (N) as the last
shift before towing.
5. Locate and remove the large IGN fuse from
the underhood fuse block. See
Underhood
Fuse Block on page 411
.
Notice:
If you tow your vehicle without
performing each of the steps listed under
“Dinghy Towing,” you could damage the
automatic transmission. Be sure to follow all
steps of the dinghy towing procedure prior
to and after towing your vehicle.
Notice:
If your vehicle has a four-speed
automatic transmission, it can be dinghy towed
from the front for unlimited miles at 65 mph
(105 km/h). If you exceed 65 mph (105 km/h)
while towing your vehicle, it could be damaged.
The repairs would not be covered by your
warranty. Never exceed 65 mph (105 km/h)
while towing your vehicle.
Notice:
If your vehicle has a five-speed
automatic transmission and it is towed for
more than seven hours without performing
lubrication process or at speeds greater than
65 mph (105 km/h), you could damage the
automatic transmission. The repairs would
not be covered by your warranty. Do not tow
your vehicle for extended periods of time or at
speeds greater than 65 mph (105 km/h).
After seven hours, repeat Step 4 above for the
five-speed automatic transmission.
287
Once you have reached your destination, do the
following:
1. Set the parking brake.
2. Shift the transmission to REVERSE (R) for a
manual transmission. Shift the transmission to
PARK (P) for an automatic transmission.
3. Turn the ignition key to LOCK and remove the
key from the ignition.
4. Reinstall the large IGN fuse.
Notice:
Too much or too little fluid can
damage the transmission. Be sure that the
transaxle fluid is at the proper level before
towing with all four wheels on the ground.
Notice:
Don’t tow a vehicle with the front drive
wheels on the ground if one of the front tires
is a compact spare tire. Towing with two
different tire sizes on the front of the vehicle
can cause severe damage to the transmission.
Dolly Towing (All-Wheel-Drive Vehicles)
All-wheel-drive vehicles should not be towed with
two wheels on the ground. To properly tow
these vehicles, they should be placed on a
platform trailer with all four wheels off of the
ground or dinghy towed from the front.
Dolly Towing
(Front-Wheel-Drive Vehicles)
288
Trailer Wiring
Additional wire length has been provided for
connecting trailer wiring to your vehicle. A loop of
five wires is stored below the jack, which is located
on the driver’s side of the cargo area. The wires are
fused in both the underhood and instrument fuse
block. See
Instrument Panel Fuse Block on
page 410
and
Underhood Fuse Block on page 411
.
The wires do not have a connector and should be
wired to the trailer by a qualified electrical
technician. The technician can use the following
information when connecting a trailer wiring
harness to your vehicle.
Yellow: Left Turn Signal
Brown: Parking Lamps
Light Blue: Stop Lamps
Black: Ground Wire
Dark Green: Right Turn Signal
When connecting a trailer harness, be sure you
leave it loose enough so the wiring does not bend
or break, but not so loose that it drags on the
ground. Store harness below jack in the cargo area
when it is not in use. Wrap the harness together
and tie it neatly so it will not be damaged.
300
A. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 324
.
B. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 318
.
C. Engine Oil Fill Cap. See “When to Add Engine
Oil” under
Engine Oil on page 318
.
D. Remote Negative (
) Terminal. See
Jump
Starting on page 348
.
E. Brake/Clutch Cylinder Fluid. See
Brakes on
page 343
and
Hydraulic Clutch on page 331
.
F. Underhood Fuse Block. See
Underhood Fuse
Block on page 411
.
G. Battery. See
Battery on page 347
.
H. Remote Positive (+) Terminal. See
Jump
Starting on page 348
.
I. Engine Coolant Surge Tank. See “Checking
Coolant” under
Engine Coolant on page 331
.
J. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 341
.
315
A. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 324
.
B. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” under
Engine Oil on
page 318
.
C. Engine Oil Fill Cap (Out of View). See “When
to Add Engine Oil” under
Engine Oil on
page 318
.
D. Remote Negative (
) Terminal. See
Jump
Starting on page 348
.
E. Brake Fluid Reservoir. See
Brakes on
page 343
.
F. Battery. See
Battery on page 347
.
G. Underhood Fuse Block. See
Underhood Fuse
Block on page 411
.
H. Remote Positive (+) Terminal (Out of View).
See
Jump Starting on page 348
.
I. Engine Coolant Surge Tank. See “Checking
Coolant” under
Engine Coolant on page 331
.
J. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 341
.
317
Notice:
If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty.
Always turn off your radio and other
accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles.
Unplug unnecessary accessories plugged into
the cigarette lighter or the accessory power
outlet. Turn off the radio and all lamps that are
not needed. This will avoid sparks and help
save both batteries. And it could save
the radio!
4. Open the hood on the other vehicle and
locate the positive (+) and negative (
)
terminal locations on that vehicle.
Open the hood on your vehicle and find the
remote positive (+) and remote negative (
)
jump starting terminals.
A. Remote Positive
B. Remote Negative
Vehicles equipped with the 2.2L L4 engine,
the remote positive (+) terminal is located
in the engine compartment on the driver’s side
of the vehicle, on the underhood fuse block.
See
Engine Compartment Overview on
page 314
for more information on location.
Access the remote positive (+) terminal
by removing the fuse block cover.
The remote negative (
) terminal is the lift
hook, which is located towards the rear of the
engine on the driver’s side.
2.2L L4 Engine
349
Notice:
If the jumper cables are connected or
removed in the wrong order, electrical shorting
may occur and damage the vehicle. The repairs
would not be covered by your warranty. Always
connect and remove the jumper cables in the
correct order, making sure that the cables do
not touch each other or other metal.
A. Heavy, Unpainted Metal Engine Part or
Remote Negative (
) Terminal
B. Good Battery or Remote Positive (+) and
Remote Negative (
) Terminals
C. Dead Battery or Remote Positive (+) Terminal
To disconnect the jumper cables from both
vehicles, do the following:
1. Disconnect the black negative (
) cable from
the vehicle that had the dead battery.
2. Disconnect the black negative (
) cable from
the vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the
other vehicle.
5. Return the underhood fuse block cover to its
original position, if applicable.
All-Wheel Drive
If you have an all-wheel-drive vehicle, be sure to
perform the lubricant checks described in this
section. There are two additional systems
that need lubrication.
Jumper Cable Removal
353
Electrical System
Add-On Electrical Equipment
Notice:
Do not add anything electrical to your
vehicle unless you check with your retailer
first. Some electrical equipment can damage
your vehicle and the damage would not
be covered by your warranty. Some add-on
electrical equipment can keep other
components from working as they should.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, see
Servicing Your Airbag-Equipped
Vehicle on page 88
.
Windshield Wiper Fuses
The windshield wiper motor is protected by a
circuit breaker and a fuse. If the motor overheats
due to heavy snow or ice, the wiper will stop
until the motor cools. If the overload is caused by
some electrical problem, have it fixed.
Power Windows and Other
Power Options
Circuit breakers in the fuse panel protect the
power windows and other power accessories.
When the current load is too heavy, the circuit
breaker opens and closes, protecting the circuit
until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by fuses. This greatly reduces
the chance of circuit overload and fire caused
by electrical problems.
There are two fuse blocks — the underhood fuse
block, and the instrument panel fuse block.
To identify and check fuses and relays, refer to
the Fuse Usage Chart on the inside surface of the
fuse panel door.
409
Instrument Panel Fuse Block
The instrument panel fuse block is located on the
passenger’s side of the lower console.
Fuses
Usage
CRUISE
Cruise Control Switch, Brake Switch
EPS
Electronic Power Steering
IGN 1
Instrument Cluster, Brake
Transmission Shift Interlock
Solenoid, Traction Switch, Fog
Lamp Switch
LOCK/MIRROR
Power Door Locks, Power Mirror,
Entry Control
BCM
Body Control Module, Front Wipers,
Windows, Sunroof
BCM (IGN 1)
Body Control Module
AIR BAG
Sensing and Diagnostic Module
RADIO (IGN)
Radio, Power Mirror, Premium
Radio Amplifier
TURN
Turn Lamps
HVAC
HVAC Control Head
HAZARD
Hazard Lamps
HTD SEATS
Heated Seats
RADIO
Radio, Data Link Connector
PARK
Park Lamps, Taillamps, Side Marker
Lamps, License Lamps
410
Fuses
Usage
BCM/CLUSTER
Body Control Module, Instrument
Cluster
INT LTS
Body Control Module, OnStar
®
DR LKS
Door Locks
Relays
Usage
AFTER BLOW
Not Used
HVAC
BLOWER
HVAC Control Head
PK LP
Parking Lamps
DR LCK
All Door Lock Switch
PSG DR
UNLCK
Passenger Door Unlock Switch
DRV DR
UNLCK
Driver Door Unlock Switch
HDLP
Headlamps
Underhood Fuse Block
The underhood fuse block is located in the
forward part of the engine compartment near
the battery.
Fuses
Usage
ECM/TCM
Battery Voltage to ECM, TCM, PCM
(3.5L V6 (L66))
BATT FEED
Instrument Panel Fuse Box
HORN
Horn
* *
Emissions
411
Fuses
Usage
ABS PWR
Anti-lock Brake System Battery
REAR DEFOG
Rear Defogger
COOL HI (L4)/
COOL 1 (V6)
Cooling Fans High (L4)/Cooling
Fan 1 (V6)
FOG LP
Fog Lamps
LH HDLP
Driver’s Side Headlamp
RR WIPER
Rear Wiper
ABS
Anti-lock Brake System Module
PWR WDW
Power Window Relay and Sunroof
CIGAR/AUX2
Cigarette Lighter
HVAC
BLOWER
HVAC Blower Motor
RH HDLP
Right Headlamp
FRT WIPER
Front Wiper
ETC
Engine Control Module (ECM),
Electronic Throttle Control (V6)
SUNROOF
Sunroof Module
BRAKE
Stoplamps
IGN
Ignition switch
Fuses
Usage
IGN/INJ (L4),
ECM/
CAM (V6)
Engine Ignition Module, Fuel
Injectors (2.2L L4 (L61))
Camshaft Sensor, Main Relay
Voltage To PCM, Ignition Coils 1-6
INJECTORS
(3.5L V6 (L66))
Fuel Injection
PWR TRAIN
Engine Control Module (ECM),
Transaxle Control Module (TCM),
Transaxle, L66 Powertrain Control
Module (PCM)
BACKUP
Low Coolant Switch, Backup Lamps
(2.2L L4 (L61)), Vehicle Speed
Sensor (Manual), Transaxle Range
Switch (2.2L L4 (L61))
HTD SEATS
Heated Seats
COOL
LO (L4)/
COOL 2 (V6)
Cooling Fan Low (L4), Cooling
Fan (V6)
A/C CLUTCH
Air Conditioning Clutch, Back Up
Lamps (3.5L V6 (L66))
FUEL PUMP
Fuel Pump
AUX 1
OUTLET
Front Auxiliary Power Outlet
412
Fuses
Usage
PREM AUD
Premium Radio Amplifier
ABS
Anti-lock Brake System Ignition
PWR SEAT
Power Seats
Relays
Usage
FOG LP
Fog Lamps
COOL FAN
HI (L4)
Cooling Fan Motor High
ENG MAIN
Engine Control Module/CAM,
Emissions, Injectors, Electronic
Throttle Control
REAR DEFOG
Rear Defog System
HORN
Horn
DRL
Daytime Running Lamps
COOL
FAN 1 (V6)
Cooling Fan
WIPER
SYSTEM
Wiper System
Relays
Usage
PRW WDO
Power Window Switch, Sunroof
Module
FRT WIPER
Front Wiper System
COOL FAN
LOW (L4)
Cooling Fan Motor Low
A/C CLUTCH
Air Conditioning Clutch
BACKUP
LAMPS (V6)
Back-up Lamps (V6)
FUEL PUMP
Fuel Pump System
RR WIPER
Rear Wiper System
COOL
FAN 2 (V6)
Cooling Fan (V6)
Misc.
Usage
FUSE PULLER
Fuse Puller
Diode
Air Conditioning Diode
413