Saturn Relay - 2007 Fuse Box Diagram

Saturn Relay - 2007 Fuse Box Diagram

PASS-Key
®
III Operation
Your vehicle is equipped
with the PASS-Key
®
III
(Personalized
Automotive Security
System) theft-deterrent
system. PASS-Key
®
III
is a passive theft
deterrent system.
This means you do not have to do anything
different to arm or disarm the system. It works
when you insert or remove the key from the
ignition.
When the PASS-Key
®
III system senses that
someone is using the wrong key, it shuts down
the vehicle’s starter and fuel systems. The starter
will not work and fuel will stop being delivered
to the engine. Anyone using a trial-and-error
method to start the vehicle will be discouraged
because of the high number of electrical
key codes.
If the engine does not start and the security
message comes on, the key may have a damaged
transponder. Turn the ignition off and try again.
If the engine still does not start, and the key
appears to be undamaged, try another ignition
key. At this time, you may also want to check the
instrument panel PASS KEY fuse. If the engine
still does not start with the other key, your vehicle
needs service. If your vehicle does start, the
first key may be faulty. See your retailer or
a locksmith who can service the PASS-Key
®
III to
have a new key made. See
Fuses and Circuit
Breakers on page 512
.
136
L
Windshield Washer. See
Windshield
Washer on page 186
.
Z
Rear Window Wiper. See
Windshield
Washer on page 186
.
=
Rear Window Washer. See
Windshield
Washer on page 186
.
For information on the headlamps, see
Exterior
Lamps on page 192
.
Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will
return automatically.
An arrow on the
instrument panel cluster
will flash in the direction
of the turn or lane
change.
To signal a lane change, just raise or lower the
lever until the arrow starts to flash. Hold it
there until you complete your lane change. The
lever will return by itself when you release it.
As you signal a turn or a lane change, if the arrow
flashes faster than normal, a signal bulb may
be burned out and other drivers will not see your
turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when
you signal a turn, check for burned-out bulbs and
check the fuse. See
Bulb Replacement on
page 455
and
Fuses and Circuit Breakers on
page 512
.
If you have a trailer towing option with added
wiring for the trailer lamps, the signal indicator will
flash at a normal rate even if a turn signal bulb
is burned out. Check the front and rear turn signal
lamps regularly to make sure they are working.
184
Accessory Power Outlet(s)
Your vehicle is equipped with a front accessory
power outlet located near the floor on the
instrument panel. It can be used to plug in
electrical equipment such as a cellular telephone
or CB radio.
Pull the cover down to use the accessory power
outlet. When not in use, keep the cover on.
The rear accessory power outlet is located behind
the third row seats on the driver’s side behind
an access cover.
To remove the cover, pull the tab on the cover
and pull it off. To put the cover back on, line up the
tabs at the back of the cover and put the cover
in place. Push down the tab to secure the cover.
When not in use, always cover the rear
accessory power outlet with the protective cap.
Notice:
Leaving electrical equipment on
for extended periods will drain the battery.
Always turn off electrical equipment when not
in use and do not plug in equipment that
exceeds the maximum amperage rating of
20 amperes.
Certain electrical accessories may not be
compatible with the accessory power outlet and
could result in blown vehicle or adapter fuses.
If you experience a problem see your retailer for
additional information on accessory power outlets.
Notice:
Adding any electrical equipment to
your vehicle may damage it or keep other
components from working as they should.
The repairs would not be covered by your
warranty. Do not use equipment exceeding
maximum amperage rating of 20 amperes.
Check with your retailer before adding
electrical equipment.
When adding electrical equipment, be sure to
follow the proper installation instructions included
with the equipment.
Notice:
Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.
203
Cigarette Lighter
Your vehicle may have a cigarette lighter. To use
the lighter, located on the instrument panel
below the climate controls, push it in all the way
and let go. When it is ready, it will pop back out
by itself.
Notice:
Holding a cigarette lighter in while it
is heating will not allow the lighter to back
away from the heating element when it is hot.
Damage from overheating may occur to the
lighter or heating element, or a fuse could be
blown. Do not hold a cigarette lighter in
while it is heating.
Notice:
If you put papers, pins, or other
flammable items in the ashtray, hot cigarettes
or other smoking materials could ignite
them and possibly damage your vehicle. Never
put flammable items in the ashtray.
Climate Controls
Climate Control System
With this system you can control the heating,
cooling and ventilation for your vehicle.
205
Oil Pressure Light
If you have low engine
oil pressure, this light
will stay on after
you start your engine, or
come on when you
are driving.
This indicates that your engine is not receiving
enough oil. The engine could be low on oil,
or could have some other oil problem. Have it
fixed immediately by your GM retailer.
The oil light could also come on in three other
situations:
When the ignition is on but the engine is not
running, the light will come on as a test to show
you it is working. The light will go out when you
turn the ignition on. If it does not come on with
the ignition on, you may have a problem with
the fuse or bulb. Have it fixed right away.
If you are idling at a stop sign, the light may
blink on and then off.
If you make a hard stop, the light may come on
for a moment. This is normal.
{
CAUTION:
Do not keep driving if the oil pressure is
low. If you do, your engine can become so
hot that it catches fire. You or others could
be burned. Check your oil as soon as
possible and have your vehicle serviced.
Notice:
Lack of proper engine oil maintenance
may damage the engine. The repairs would
not be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
Security Light
For information
regarding this light, see
Theft-Deterrent
Systems on page 133
.
232
SERVICE PARK LAMPS
This message displays when there is a problem
with the park lamps. Check to see if the park lamp
fuse is blown and replace the fuse if necessary.
See
Fuses and Circuit Breakers on page 512
and
Instrument Panel Fuse Block on page 512
for
more information. If changing the fuse does not
correct the problem, see your retailer.
This message only displays while the ignition is in
RUN. Press any of the DIC buttons to acknowledge
this message and to clear it from the screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine is
turned off. It also re-displays for two seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
SERVICE STABILITY SYSTEM
If your vehicle has StabiliTrak
®
, this message
displays if there has been a problem detected with
StabiliTrak
®
. See
StabiliTrak
®
System on
page 367
.
If this message turns on while you are driving, pull
off the road as soon as possible and stop
carefully. Try resetting the system by turning the
ignition off and then back on. If this message
still stays on or turns back on again while you are
driving, your vehicle needs service. Have the
StabiliTrak
®
System inspected by your retailer as
soon as possible.
This message displays only while the ignition is in
RUN. Press any of the DIC buttons to acknowledge
this message and to clear it from the screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine is
turned off. It also re-displays for two seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
257
Mobile Digital Media Player Care
Never spray any type of liquid such as a
cleaning agent inside of an open cartridge
panel on the Digital Media player. Doing this
may damage the parts or inside mechanism
needed to help operate the unit.
Do not use any object to probe the opening of
the Mobile Digital Media player and do not put
any body parts or other foreign objects in
the opening of the product.
Tips and Troubleshooting Chart
Problem
Cause and Solution
The Digital Media system and RSE system will not
come on at all.
A fuse in the car has blown. After checking for
short circuits in the wires, replace the fuse with
one of the same rating.
The RSE screen displays DMS MEDIA NOT
INSERTED.
The DMS cartridge is not fully inserted. Fully
insert the DMS cartridge.
The RSE screen displays DMS MEDIA LOADING.
The system is still booting. Please wait up to
15 seconds for the system to boot and then
switch back to digital media mode.
348
Engine Compartment Overview
When you open the hood on the 3.9L V6 engine, here is what you will see:
422
A. Underhood Fuse Block. See
Underhood Fuse
Block on page 514
.
B. Remote Positive (+) Terminal. See
Jump
Starting on page 450
.
C. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 444
.
D. Radiator Pressure Cap. See
Radiator Pressure
Cap on page 435
.
E. Power Steering Fluid Reservoir. See
Power
Steering Fluid on page 443
.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” under
Engine Oil on page 423
.
G. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 423
.
H. Automatic Transaxle Fluid Dipstick. See
“Checking the Fluid Level” under
Automatic
Transaxle Fluid on page 430
.
I. Brake Master Cylinder Reservoir. See “Brake
Fluid” under
Brakes on page 445
.
J. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 428
.
K. Engine Coolant Recovery Tank. See
Cooling
System on page 438
.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop.
See
Engine Compartment Overview on page 422
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil
several minutes to drain back into the oil pan.
If you do not do this, the oil dipstick might
not show the actual level.
2. Pull out the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down,
and check the level.
423
The terminal is located
under the fuse block
cover. Remove
the cover to access
the remote positive (+)
terminal.
See
Engine Compartment Overview on
page 422
for more information on the location
of the remote positive (+) terminal. You
should always use the remote positive (+)
terminal instead of the positive (+) terminal
on your battery.
{
CAUTION:
An electric fan can start up even when the
engine is not running and can injure you.
Keep hands, clothing and tools away from
any underhood electric fan.
{
CAUTION:
Using a match near a battery can cause
battery gas to explode. People have been
hurt doing this, and some have been
blinded. Use a flashlight if you need
more light.
Be sure the battery has enough water.
You do not need to add water to the
battery installed in your new vehicle.
But if a battery has filler caps, be sure the
right amount of fluid is there. If it is low,
add water to take care of that first. If you
do not, explosive gas could be present.
Battery fluid contains acid that can
burn you. Do not get it on you. If you
accidentally get it in your eyes or on your
skin, flush the place with water and get
medical help immediately.
452
To disconnect the jumper cables from both
vehicles, do the following:
1. Disconnect the black negative (
) cable from
the vehicle that had the dead battery.
2. Disconnect the black negative (
) cable from
the vehicle with the good battery.
3. Disconnect the red positive (+) cable from
the vehicle with the good battery.
4. Disconnect the red positive (+) cable from
the other vehicle.
5. Return the remote positive (+) terminal
cover or underhood fuse block cover to
its original position.
Bulb Replacement
For the type of bulb to use, see
Replacement
Bulbs on page 460
.
For any bulb changing procedure not listed in this
section, contact your retailer.
Halogen Bulbs
{
CAUTION:
Halogen bulbs have pressurized gas
inside and can burst if you drop or
scratch the bulb. You or others could be
injured. Be sure to read and follow the
instructions on the bulb package.
455
If the accessory inflator system does not turn on
or the light does not come on, the fuse may
be blown or installed incorrectly. See
Fuses and
Circuit Breakers on page 512
or see your
retailer for service.
Your accessory inflator will automatically shut off
after about 10 minutes. The light in the switch
will blink. After about one minute you can use the
system again. Press the switch and the indicator
light will come on.
Notice:
If you run the accessory inflator
longer than 30 minutes at a time, you could
damage the inflator. The repairs would not be
covered by your warranty. Run the inflator
for short periods of time only.
After running the accessory inflator for 30 minutes,
wait at least 10 minutes before restarting the
accessory inflator.
To turn off the inflator, do the following:
1. Press the switch and detach the hose, first
from the inflated object, then from the outlet.
2. Put the protective cap back on.
3. Place the inflator kit tools in the pouch, and
store in the rear compartment on the
passenger’s side.
To put the cover back on, line up the tabs at the
bottom of the cover and put it in place. Push down
the tab to secure the cover.
482
Electrical System
Add-On Electrical Equipment
Notice:
Do not add anything electrical to your
vehicle unless you check with your retailer
first. Some electrical equipment can damage
your vehicle and the damage would not
be covered by your warranty. Some add-on
electrical equipment can keep other
components from working as they should.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, see
Servicing Your Airbag-Equipped
Vehicle on page 99
.
Headlamp Wiring
The headlamp wiring is protected by four internal
fuses in the underhood fuse block. An electrical
overload will cause the lamps to go on and off, or
in some cases to remain off. If this happens,
have your headlamp wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by
an internal fuse in the underhood fuse block.
If the motor overheats due to heavy snow, etc.,
the wiper will stop until the motor cools. If the
overload is caused by some electrical problem,
be sure to get it fixed.
The rear washer pump is controlled by a relay
located in the engine compartment, behind
the windshield washer fluid reservoir. The rear
wiper motor is protected by a fuse located in the
instrument panel fuse block.
Power Windows and Other Power
Options
Circuit breakers in the instrument panel fuse panel
protect the power windows and other power
accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting
the circuit until the problem is fixed.
511
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by a combination of fuses,
circuit breakers, and fusible thermal links.
Look at the silver-colored band inside the fuse.
If the band is broken or melted, replace the fuse.
Be sure you replace a bad fuse with a new
one of the identical size and rating.
If you ever have a problem on the road and do not
have a spare fuse, you can borrow one that has
the same amperage or use one of the spare fuses
in the underhood fuse block. Just pick some
feature of your vehicle that you can get along
without, like the radio or cigarette lighter, and use
its fuse if it is the right amperage. Replace it
as soon as you can.
There are two fuse blocks in your vehicle, the
instrument panel fuse block and the underhood
fuse block.
Instrument Panel Fuse Block
The instrument panel fuse block is located at
the right end of the instrument panel, on the
passenger’s side of the vehicle. Open the front
passegner’s door, and remove the cover, to
access the fuse block.
Your vehicle may not have all of the fuses listed.
512
Fuses
Usage
1
Trunk, Door Locks
2
Electronic Level Control
3
Rear Wiper
4
Radio, DVD Player
5
Interior Lamps
6
OnStar
®
7
Keyless Entry Module
8
Cluster, Heating, Ventilation,
Air Conditioning
9
Cruise Switch
10
Steering Wheel Illumination
11
Power Mirror
12
Stoplamp, Turn Lamps
13
Heated Seats
14
Blank
15
Electronic Level Control
513
Your vehicle may not have all the fuses listed.
Fuses
Usage
1
Right High-Beam
2
Fuel Pump
Fuses
Usage
3
Diode
BLANK
Not Used
515
Fuses
Usage
BLANK
Not Used
4
Left High-Beam
BLANK
Not Used
BLANK
Not Used
BLANK
Not Used
5
Not Used
6
Air Conditioning Clutch
7
Horn
8
Left Low-Beam
9
Powertrain Control Module,
Electronic Throttle Control
10
Not Used
11
Transmission Solenoid
12
Right Low-Beam
13
Anti-lock Brake System
14
Powertrain Control Module Ignition
Fuses
Usage
15
Electronic Ignition
16
Fuel Injector
17
Climate Control, RPA,
Cruise Control
18
Electronic Throttle Control
19
Engine Sensor, Evaporator
20
Airbag
21
Not Used
22
Not Used
23
Auxiliary Power
24
Front Windshield Washer
25
AC/DC Inverter
26
Rear Blower
27
Front Blower
28
Front Windshield Wiper
516
J-Case Fuses
Usage
PLR
Fuse Puller
29
Fan 1
30
Starter Solenoid
31
Anti-lock Brake System Motor
32
Blank
33
Fan 2
34
Front Blower High
35
Battery Main 3
36
Rear Defogger
37
Battery Main 2
38
Spare
Relays
Usage
RUN RLY
Starter
LO BEAM
Low-Beam
FUEL PUMP
Fuel Pump
HORN
Horn
AC/CLTCH
Air Conditioning Clutch
HI BEAM
High-Beam
PWR/TRN
Powertrain
WPR2
Wiper 2
WPR1
Wiper 1
FAN 1
Fan 1
CRNK
Crank
IGN MAIN
Ignition Main
FAN2
Fan 2
FAN3
Fan 3
BLANK
Not Used
517