Saturn Outlook - 2007 Fuse Box Diagram

Saturn Outlook - 2007 Fuse Box Diagram

The theft-deterrent system will not activate if the
doors are locked with the vehicle’s key or the
manual door lock. It activates only if you use the
power door lock switch with the door open or
the RKE transmitter. You should also remember
that you can start your vehicle with the correct
ignition key if the alarm has been set off.
Here is how to avoid setting off the alarm by
accident:
If you do not want to activate the
theft-deterrent system, the vehicle should be
locked with the door key after the doors
are closed.
Always unlock a door with the RKE transmitter.
Unlocking a door any other way will set off the
alarm if the system has been armed.
If you set off the alarm by accident, turn off the
alarm by pressing unlock on the RKE transmitter or
by placing the key in the ignition and turning it
to START.
Testing the Alarm
To test the alarm:
1. From inside the vehicle, lower the driver’s
window and open the driver’s door.
2. Activate the system by locking the doors with
the RKE transmitter.
3. Get out of the vehicle, close the door and wait
for the security light to go out.
4. Then reach in through the window, unlock the
door with the manual door lock and open the
door. This should set off the alarm.
If the alarm does not sound when it should, but
the vehicle’s headlamps flash, check to see if the
horn works. The horn fuse may be blown. To
replace the fuse, see
Fuses and Circuit Breakers
on page 476
.
If the alarm does not sound or the vehicle’s
headlamps do not flash, see your dealer/retailer
for service.
120
To signal a lane change, raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return
by itself when you release it. If you momentarily
press and release the lever, the turn signal
will flash three times.
If the arrow flashes faster than normal as you
signal a turn or a lane change, a signal bulb may
be burned out and other drivers will not see
your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when
you signal a turn, check for burned-out bulbs and
then check the fuse. See
Fuses and Circuit
Breakers on page 476
.
Turn Signal On Chime
If you leave either one of your turn signals on and
drive more than 3/4 mile (1.2 km), a chime will
sound to alert you.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to
high beam, push the turn signal/multifunction lever
toward the front of the vehicle.
This light on the
instrument panel cluster
comes on if the high
beam lamps are turned
on while the ignition
is on.
To change the headlamps from high beam to low
beam, pull the turn signal lever toward the rear
of the vehicle.
175
Accessory Power Outlet(s)
The accessory power outlets can be used to
connect electrical equipment such as a cellular
phone or CB radio.
Your vehicle may have four accessory power
outlets. They are located on the instrument panel
below the climate controls, inside the front
center console storage bin, at the rear of the
center console, and in the rear cargo area.
To use the outlets, remove the cover. When not in
use, always cover the outlet with the protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always
turn off electrical equipment when not in
use and do not plug in equipment that exceeds
the maximum amperage rating of 20 amperes.
Certain electrical accessories may not be
compatible with the accessory power outlets and
could result in blown vehicle or adapter fuses.
If you experience a problem, see your
dealer/retailer for additional information on the
accessory power outlet.
Notice:
Adding any electrical equipment to
your vehicle may damage it or keep other
components from working as they should. The
repairs would not be covered by your
warranty. Do not use equipment exceeding
maximum amperage rating of 20 amperes.
Check with your dealer/retailer before adding
electrical equipment.
When adding electrical equipment, be sure to
follow the installation instructions included with the
equipment.
Notice:
Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.
192
6. Shift your transmission to NEUTRAL (N).
7. Release the parking brake.
Notice:
If you tow your vehicle without
performing each of the steps listed under
“Dinghy Towing,” you could damage the
automatic transmission. Be sure to follow all
steps of the dinghy towing procedure prior
to and after towing your vehicle.
Notice:
If you exceed 65 mph (105 km/h) while
towing your vehicle, it could be damaged.
Never exceed 65 mph (105 km/h) while towing
your vehicle.
Once you have reached your destination, do the
following:
1. Set the parking brake.
2. Turn the ignition key to OFF and remove the
key from the ignition.
3. Reinstall the IGN (Ignition) fuse.
Notice:
Don’t tow a vehicle with the front
drive wheels on the ground if one of the front
tires is a compact spare tire. Towing with
two different tire sizes on the front of the
vehicle can cause severe damage to the
transmission.
Dolly Towing (All-Wheel-Drive Vehicles)
All-wheel-drive vehicles must not be towed with
two wheels on the ground. To properly tow
these vehicles, they should be placed on a
platform trailer with all four wheels off of the
ground or dinghy towed from the front.
360
The seven-wire harness contains the following
trailer circuits:
Yellow: Left Stop/Turn Signal
Dark Green: Right Stop/Turn Signal
Brown: Taillamps
White: Ground
Light Green: Back-up Lamps
Red: Battery Feed*
Dark Blue: Trailer Brake*
*The fuses for these two circuits are installed in
the underhood electrical center, but the wires
are not connected. They should be connected by
your dealer/retailer or a qualified service center.
If you are charging a remote (non-vehicle) battery,
press the tow/haul mode button located at the
end of the shift lever. This will boost the vehicle
system voltage and properly charge the battery. If
the trailer is too light for tow/haul mode, you
can turn on the headlamps (Non-HID only) as a
second way to boost the vehicle system and
charge the battery.
Engine Cooling When Trailer Towing
Your cooling system may temporarily overheat
during severe operating conditions. See
Engine
Overheating on page 400
.
374
A. Radiator Pressure Cap (Out of View). See
Radiator Pressure Cap on page 399
.
B. Engine Coolant Recovery Cap. See
Cooling
System on page 402
.
C. Underhood Fuse Block. See
Underhood Fuse
Block on page 479
.
D. Remote Positive (+) Terminal. See
Jump
Starting on page 414
.
E. Power Steering Fluid Reservoir. See
Power
Steering Fluid on page 408
.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” under
Engine Oil on page 387
.
G. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 387
.
H. Automatic Transmission Fluid Dipstick. See
“Checking the Fluid Level” under
Automatic
Transmission Fluid on page 394
.
I. Brake Master Cylinder Reservoir. See “Brake
Fluid” under
Brakes on page 410
.
J. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 392
.
K. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 409
.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop.
See
Engine Compartment Overview on page 386
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil
several minutes to drain back into the oil
pan. If you do not do this, the oil dipstick might
not show the actual level.
2. Pull out the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down,
and check the level.
387
Electrical System
High Voltage Devices and Wiring
{
CAUTION:
Exposure to high voltage can cause
shock, burns, and even death. The high
voltage systems in your vehicle can only
be serviced by technicians with special
training.
High voltage devices are identified by
labels. Do not remove, open, take apart, or
modify these devices. High voltage cable
or wiring has orange covering. Do not
probe, tamper with, cut, or modify high
voltage cable or wiring.
Add-On Electrical Equipment
Notice:
Do not add anything electrical to
your vehicle unless you check with your
dealer/retailer first. Some electrical equipment
can damage your vehicle and the damage
would not be covered by your warranty. Some
add-on electrical equipment can keep other
components from working as they should.
Add-on equipment can drain your vehicle’s battery,
even if your vehicle is not operating.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, see
Servicing Your Airbag-Equipped
Vehicle on page 91
.
Windshield Wiper Fuses
The windshield wiper motor is protected by a
circuit breaker and a fuse. If the motor overheats
due to heavy snow or ice, the wiper will stop
until the motor cools. If the overload is caused by
some electrical problem, have it fixed.
475
Power Windows and Other Power
Options
Circuit breakers in the fuse panel protect the
power windows and other power accessories.
When the current load is too heavy, the circuit
breaker opens and closes, protecting the circuit
until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by a combination of fuses,
circuit breakers and fusible thermal links.
This greatly reduces the chance of fires caused by
electrical problems.
Look at the silver-colored band inside the fuse. If
the band is broken or melted, replace the fuse.
Be sure you replace a bad fuse with a new one of
the identical size and rating.
If you ever have a problem on the road and do not
have a spare fuse, you can borrow one that has
the same amperage. Just pick some feature
of your vehicle that you can get along without, like
the radio or cigarette lighter, and use its fuse if
it is the correct amperage. Replace it as soon as
you can.
Instrument Panel Fuse Block
The instrument panel fuse block is located under
the instrument panel on the passenger side of
the vehicle. Pull down on the cover to access the
fuse block.
476
Fuses
Usage
FRT/WSW
Front Windshield Wiper
SPARE
Spare
HTD/SEAT
Front Heated Seats
STR/WHL/
ILLUM
Steering Wheel Illumination
MSM
Memory Seat Module
PWR/MIRRORS Power Mirrors
DR/LCK
Door Locks
AIRBAG
Airbag System
LT/TRN/SIG
Driver Side Turn Signal
REAR WIPER
Rear Window Wiper
PWR MOD
PassKey Module, Body Control
Module
BCK/UP/STOP
Back-up Lamps, Stoplamps
HVAC
Climate Control System
DISPLAY
Display
RT/TRN/SIG
Passenger Side Turn Signal
DRL*
Daytime Running Lamps
RADIO
Radio
PDM
Power Mirrors, Liftgate Release
Fuse Side
477
Fuses
Usage
DRL 2**
Not Used
INFOTAINMENT Infotainment System
BCM
Body Control Module
SPARE
Spare
CTSY
Dome Lamps
INADV/
PWR/LED
Interior Lamps
ONSTR/VENT
Emissions
AMP
Audio Amplifier
Harness
Connector
Usage
BODY
Harness Connector
Relay Side
478
Relays
Usage
LT/PWR/SEAT
Driver Side Power Seat Relay
RT/PWR/SEAT
Passenger Side Power Seat Relay
PWR/WNDW
Power Windows Relay
PWR/COLUMN
Power Steering Column Relay
L/GATE
Liftgate Relay
LCK
Power Lock Relay
REAR/WSW
Rear Window Washer Relay
UNLCK
Power Unlock Relay
DRL2
Daytime Running Lamps 2 Relay
LT/UNLCK
Driver Side Unlock Relay
DRL
Daytime Running Lamps Relay
SPARE
Spare
FRT/WSW
Front Windshield Washer Relay
Underhood Fuse Block
The underhood fuse block is located in the engine
compartment, on the passenger side of the
vehicle.
Lift the cover for access to the fuse/relay block.
479
To remove fuses, hold the end of the fuse between your thumb and index finger and pull straight out.
480
Fuses
Usage
LT PRK
Left Parking Lamp
RT PRK
Right Parking Lamp
TRLR PRK
LAMP
Trailer Parking Lamps
AIRBAG
Airbag System
PCM IGN
Powertrain Control Module Ignition
AFS
Adaptive Forward Lighting System
TRANS
Transmission
REAR
CAMERA
Rear Camera
EMISSION 1
Antilock Brakes System 2
TRLR BRK
Trailer Brake
AWD
All-Wheel-Drive System
TRLR PWR
Trailer Power
EVEN COILS
Even Injector Coils
RR HVAC
Rear Climate Control System
SPARE
Spare
ODD COILS
Odd Injector Coils
SPARE
Spare
LT HI BEAM
Left High-Beam Headlamp
SPARE
Spare
LT TRLR
STOP/TRN
Trailer Left Stoplamp and Turn
Signal
EMISSION 2
Emission 2
Fuses
Usage
ECM
Engine Control Module
RT HI BEAM
Right High-Beam Headlamp
RVC SNSR
Regulated Voltage Control Sensor
RT TRLR
STOP/TRN
Trailer Right Stoplamp and Turn
Signal
ECM 1
Engine Control Module 1
SPARE
Spare
WPR/WSW
Windshield Wiper/Washer
SPARE
Spare
PWR OUTLET
Power Outlet
AUX POWER
Auxiliary Power
RT LO BEAM
Right Low-Beam Headlamp
RR APO
Rear Accessory Power Outlet
LT LO BEAM
Left Low-Beam Headlamp
TCM
Transmission Control Module
TRLR BCK/UP
Trailer Back-up Lamps
HTD MIR
Heated Outside Rearview Mirror
ABS MTR
Antilock Brake System Motor
FOG LAMP
Fog Lamps
HORN
Horn
A/C CLTCH
Air Conditioning Clutch
FUEL PUMP
Fuel Pump
SPARE
Spare
481
J-Case Fuses
Usage
FAN 2
Cooling Fan 2
PWR L/GATE
Power Liftgate
FAN 1
Cooling Fan 1
HVAC BLWR
Climate Control System Blower
STRTR
Starter
BATT 2
Battery 2
HTD WASH
Heated Windshield Washer System
BATT 1
Battery 1
BATT 3
Battery 3
ABS MTR
Antilock Brake System Motor
RR DEFOG
Rear Defogger
S/ROOF/
SUNSHADE
Sunroof, Sunshade
Relays
Usage
FAN 3
Cooling Fan 3
FAN 2
Cooling Fan 2
PRK LAMP
Park Lamp
FAN 1
Cooling Fan 1
Relays
Usage
RT TRLR
STOP/TRN
Trailer Right Stoplamp and Turn
Signal
LT TRLR
STOP/TRN
Trailer Left Stoplamp and Turn
Signal
IGN
Ignition Main
CRNK
Switched Power
PWR/TRN
Powertrain
HI BEAM
High-Beam Headlamps
WPR
Windshield Wiper
WPR HI
Windshield Wiper High Speed
RR DEFOG
Rear Window Defogger
HID/LO BEAM
High Intensity Discharge (HID)
Low-Beam Headlamps
SPARE
Spare
FOG LAMP
Fog Lamps
HORN
Horn
A/C CMPRSR
CLTCH
Air Conditioning Compressor Clutch
FUEL PUMP
Fuel Pump
TRLR BCK/UP
Trailer Back-up Lamps
482