Pontiac Solstice - 2007 Fuse Box Diagram

Pontiac Solstice - 2007 Fuse Box Diagram

When the PASS-Key
®
III+ system senses that
someone is using the wrong key, it prevents
the vehicle from starting. Anyone using a
trial-and-error method to start the vehicle will be
discouraged because of the high number of
electrical key codes.
When trying to start the vehicle if the engine does
not start and the security light on the instrument
panel cluster comes on, the key may have a
damaged transponder. Turn the ignition off and
try again.
If the engine still does not start, and the key
appears to be not damaged, try another ignition
key. At this time, you may also want to check the
fuse, see
Fuses and Circuit Breakers on
page 326
. If the engine still does not start with the
other key, your vehicle needs service. If your
vehicle does start, the first key may be faulty. See
your dealer who can service the PASS-Key
®
III+
to have a new key made. In an emergency,
contact Roadside Assistance. See
Roadside
Assistance Program on page 368
.
It may be possible for the PASS-Key
®
III+ decoder
to “learn” the transponder value of a new or
replacement key. Up to 10 keys may be
programmed for the vehicle. The following
procedure is for programming additional keys only.
If your vehicle was first sold in Canada, or if all
the currently programmed keys are lost or do not
operate, you must see your dealer or a locksmith
who can service PASS-Key
®
III+ to have keys
made and programmed to the system.
See your dealer or a locksmith who can service
PASS-Key
®
III+ to get a new key blank that is cut
exactly as the ignition key that operates the
system.
To program the new key do the following:
1. Verify that the new key has a
1
stamped on it.
2. Insert the already programmed key in the
ignition and start the engine. If the engine
will not start, see your dealer for service.
3. After the engine has started, turn the key to
LOCK, and remove the key.
75
Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will
return automatically.
An arrow on the
instrument panel cluster
will flash in the
direction of the turn or
lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return
by itself when you release it.
As you signal a turn or a lane change, if the
arrows flash rapidly, a signal bulb may be burned
out and other drivers will not see your turn
signal. If a bulb is burned out, replace it to help
avoid an accident.
If the arrows do not go on at all when you signal a
turn, check the fuse. See
Fuses and Circuit
Breakers on page 326
.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high
beam, push the turn signal lever away from you.
When the high beams
are on, this light on the
instrument panel
cluster will also be on.
To change the headlamps from high beam to low
beam, pull the turn signal lever toward you.
112
Battery Run-Down Protection
Your vehicle has a battery saver feature designed
to protect your vehicle’s battery.
When any interior lamp is left on and the ignition
is turned off, the battery rundown protection
system will automatically turn the lamp off after
20 minutes. This will avoid draining the battery.
Accessory Power Outlet(s)
The accessory power outlet can be used to
connect electrical equipment such as a cellular
phone or CB radio.
The accessory power outlet is located on the
instrument panel, below the radio.
To use the outlet, remove the cover. When not in
use, always cover the outlet with the protective cap.
Notice:
Leaving electrical equipment plugged
in for an extended period of time while the
vehicle is off will drain the battery. Power is
always supplied to the outlets. Always unplug
electrical equipment when not in use and
do not plug in equipment that exceeds
the maximum 20 ampere rating.
Certain electrical accessories may not be
compatible with the accessory power outlet and
could result in blown vehicle or adapter fuses.
If you experience a problem, see your dealer
for additional information on the accessory
power outlet.
Notice:
Adding any electrical equipment to
your vehicle may damage it or keep other
components from working as they should.
The repairs would not be covered by your
warranty. Do not use equipment exceeding
maximum amperage rating of 20 amperes.
Check with your dealer before adding electrical
equipment.
When adding electrical equipment, be sure to
follow the installation instructions included with
the equipment.
Notice:
Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.
121
Ashtray(s) and Cigarette Lighter
Your vehicle may have an ashtray and cigarette
lighter. To use the lighter, located on the
instrument panel below the radio, push it in all the
way and let go. When it is ready, it will pop
back out by itself.
Notice:
Holding a cigarette lighter in while it
is heating will not allow the lighter to back
away from the heating element when it is hot.
Damage from overheating may occur to the
lighter or heating element, or a fuse could be
blown. Do not hold a cigarette lighter in
while it is heating.
Notice:
If you put papers, pins, or other
flammable items in the ashtray, hot cigarettes
or other smoking materials could ignite
them and possibly damage your vehicle. Never
put flammable items in the ashtray.
Climate Controls
Climate Control System
With this system you can control the heating and
ventilation of your vehicle. You may also be
able to control the cooling of your vehicle, if your
vehicle has air conditioning. The in-between
mode will be a combination of the two modes that
the control is selected between.
Climate Control System with Air Conditioning
shown, Climate Control System without Air
Conditioning similar
122
Oil Pressure Light
If you have a low engine
oil pressure problem,
this light will stay on after
you start your engine, or
come on when you are
driving.
This indicates that your engine is not receiving
enough oil.
The engine could be low on oil, or could have
some other oil problem. Have it fixed immediately.
The oil light could also come on in three other
situations:
When the ignition is on but the engine is not
running, the light will come on as a test to
show you it is working, but the light will go out
when you turn the ignition to START. If it
does not come on with the ignition on,
you may have a problem with the fuse or bulb.
Have it fixed right away.
If you are idling at a stop sign, the light may
blink on and then off.
If you make a hard stop, the light may come
on for a moment. This is normal.
{
CAUTION:
Do not keep driving if the oil pressure is
low. If you do, your engine can become so
hot that it catches fire. You or others
could be burned. Check your oil as soon
as possible and have your vehicle
serviced.
Notice:
Lack of proper engine oil maintenance
may damage the engine. The repairs would
not be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
142
Engine Compartment Overview
When you open the hood on the 2.4L L4 engine, this is what you will see:
244
A. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 269
.
B. Coolant Surge Tank and Pressure Cap. See
Cooling System on page 262
.
C. Brake Master Cylinder Reservoir. See “Brake
Fluid” under
Brakes on page 270
and
Hydraulic
Clutch on page 256
.
D. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” under
Engine Oil on
page 247
.
E. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 254
.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” under
Engine Oil on page 247
.
G. Power Steering Fluid Reservoir. See
Power
Steering Fluid on page 268
.
H. Remote Negative (
) Ground (Out of View).
See
Jump Starting on page 274
.
I. Battery (Out of View). See
Battery on page 273
.
J. Remote Positive (+) Terminal. See
Jump
Starting on page 274
.
K. Underhood Fuse Block. See
Underhood Fuse
Block on page 329
.
245
A. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” under
Windshield
Washer Fluid on page 269
.
B. Coolant Surge Tank and Pressure Cap. See
Cooling System on page 262
.
C. Brake Master Cylinder Reservoir. See “Brake
Fluid” under
Brakes on page 270
and
Hydraulic
Clutch on page 256
.
D. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 247
.
E. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 254
.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” under
Engine Oil on page 247
.
G. Power Steering Fluid Reservoir. See
Power
Steering Fluid on page 268
.
H. Remote Negative (
) Ground (Out of View).
See
Jump Starting on page 274
.
I. Battery (Out of View). See
Battery on page 273
.
J. Remote Positive (+) Terminal. See
Jump
Starting on page 274
.
K. Underhood Fuse Block. See
Underhood Fuse
Block on page 329
.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop.
See
Engine Compartment Overview on page 244
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil several
minutes to drain back into the oil pan. If you
do not do this, the oil dipstick might not
show the actual level.
2. Pull the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down
and check the level.
247
Notice:
If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty.
Always turn off your radio and other
accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles.
Unplug unnecessary accessories plugged into
the cigarette lighter or the accessory power
outlet. Turn off the radio and all lamps that
are not needed. This will avoid sparks
and help save both batteries. And it could
save the radio!
4. Open the hood on the other vehicle and
locate the positive (+) and negative (
)
terminal locations on that vehicle.
You will not need to access your battery for
jump starting. Your vehicle has a remote
positive (+) and a remote negative (
) jump
starting terminal.
The remote positive (+)
terminal is located
under a red plastic
cover on the engine
compartment fuse block.
Open the cover to
access the terminal.
275
Electrical System
Add-On Electrical Equipment
Notice:
Do not add anything electrical to your
vehicle unless you check with your dealer
first. Some electrical equipment can damage
your vehicle and the damage would not
be covered by your warranty. Some add-on
electrical equipment can keep other
components from working as they should.
Add-on equipment can drain your vehicle’s battery,
even if your vehicle is not operating.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, see
Servicing Your Airbag-Equipped
Vehicle on page 54
.
Headlamp Wiring
The headlamp wiring is protected by fuses. An
electrical overload will cause the lamps to remain
off. If this happens, have your headlamp wiring
checked right away.
Power Windows and Other
Power Options
Circuit breakers protect the power windows and
other power accessories. When the current load is
too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed
or goes away.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of J-Case fuses,
mini-fuses and circuit breakers. This greatly reduces
the chance of fires caused by electrical problems.
326
Look at the silver-colored band inside the fuse.
If the band is broken or melted, replace the fuse.
Be sure you replace a bad fuse with a new
one of the identical size and rating.
If you ever have a problem on the road and do not
have a spare fuse, you can borrow one that has
the same amperage. Just pick some feature of your
vehicle that you can get along without — like the
radio or cigarette lighter — and use its fuse, if it
is the correct amperage. Replace it as soon as
you can.
Floor Console Fuse Block
The floor console fuse block is located on the
passenger’s side of the vehicle under the carpet.
Remove the fuse block cover to access the
fuses. Use the fuse puller to remove fuses.
After re-installing the fuse block cover, be sure to
tuck the carpet under the heater floor outlets.
Fuses
Usage
1
Fuse Puller
2
Empty
3
Empty
4
Empty
5
Empty
327
Fuses
Usage
6
Amplifier
7
Cluster
8
Ignition Switch, PassKey III+
9
Stoplamp
10
Climate Control System,
PassKey III+
11
Empty
12
Spare
13
Airbag
14
Spare
15
Wiper
16
Climate Control System,
Automatic Occupant Sensing
Module, Clutch Switch,
Crank Relay, Instrument
Panel Cluster
17
Empty
18
Empty
Fuses
Usage
19
Electric Power Steering,
Steering Wheel Controls
20
Spare
21
Spare
22
Empty
23
Radio
24
Sensing and Diagnostic Module
25
Engine Control Module,
Transmission Control Module
26
Door Locks
27
Interior Lamps
28
Steering Wheel Control Backlighting
29
Power Windows
30
Climate Control System
31
Empty
32
Retained Accessory Power
328
Fuses
Usage
9
Empty
10
Trunk
11
Trunk
12
Empty
13
Fuel Pump
14
Rear Defogger Relay
15
Air Conditioning Clutch Relay
16
Empty
17
Empty
18
Trunk Release Relay
19
Fuel Pump Relay
20
Empty
21
Mirrors
22
Air Conditioning
23
Empty
24
Cooling Fan 2 Relay (LE5);
Empty (LNF)
25
Fuse Puller
26
Powertrain Relay
Fuses
Usage
27
Empty
28
Back-up Lamps Relay
(Automatic Transmission);
Empty (Manual Transmission)
29
Data Link Connector
30
Outlet
31
Back-up Lamps
(Automatic Transmission);
Empty (Manual Transmission)
32
Empty (LE5); Vacuum Pump (LNF)
33
Emissions
34
Crank Relay
35
Empty
36
Empty
37
Power Seat
38
Empty (LE5); Vacuum Pump
Relay (LNF)
39
Empty
40
Cooling Fan 1 (LE5); Empty (LNF)
41
Empty (LE5); Turbo, Cam
Phaser (LNF)
330
Fuses
Usage
42
Engine Control Module
43
Engine Control Module,
Transmission
44
Anti-lock Brake System
45
Injectors, Ignition Coils (LE5);
Ignition Coils (LNF)
46
Back-up Lamps
(Manual Transmission);
Empty (Automatic Transmission)
47
Empty
48
Daytime Running Lamps Relay
49
Daytime Running Lamps
50
Cooling Fan 1 Relay (LE5);
Empty (LNF)
51
Run/Crank Relay
52
Windshield Wiper Low/High Relay
53
Fog Lamps
54
Fog Lamps Relay
55
Horn Relay
56
S Band, OnStar
®
, Remote
Keyless Entry System
Fuses
Usage
57
Anti-lock Brake System
58
Wiper Diode
59
Windshield Wiper
60
Horn
61
Anti-lock Brake System
62
Instrument Panel Ignition
63
Driver’s Side High Beam
64
Canister Vent
65
Driver’s Side Low-Beam
Headlamp
66
Passenger’s Side Low-Beam
Headlamp
67
Passenger’s Side High-Beam
Headlamp
68
Parking Lamps Relay
69
Parking Lamps
70
Windshield Wiper On/Off Relay
71
Low-Beam Headlamp Relay
72
High-Beam Headlamp Relay
331