Saturn VUE - 2006 Fuse Box Diagram

Saturn VUE - 2006 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
Theft-Deterrent Systems
Vehicle theft is big business, especially in some cities.
Although your vehicle has a number of theft-deterrent
features, we know that nothing we put on it can make
it impossible to steal.
Passlock
®
Your vehicle is equipped with the
Passlock
®
theft-deterrent system.
This light will come on for
the theft-deterent system.
Passlock
®
is a passive theft-deterrent system.
Passlock
®
enables fuel if the ignition lock cylinder is
turned with a valid key. If a correct key is not used or the
ignition lock cylinder is tampered with, fuel is disabled.
During normal operation, the security light will go off
approximately five seconds after the key is turned
to RUN following an engine start.
If the engine stalls and the security light flashes, wait
until the light stops flashing before trying to restart
the engine. Remember to release the key from START
as soon as the engine starts.
If the engine is running and the security light comes
on, you will be able to restart the engine if you turn the
engine off. However, your Passlock
®
system is not
working properly and must be serviced by your retailer.
Your vehicle is not protected by Passlock
®
at this
time. You may also want to check the fuses, see
Fuses
and Circuit Breakers on page 5-94
. See your retailer
for service. Also, see
Roadside Assistance Program
on page 7-6
for more information.
2-14
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
G
Turn and Lane-Change Signals. See
Turn
and Lane-Change Signals on page 3-7
.
O
Exterior Lamp Control. See
Headlamps
on page 3-13
.
2
Headlamp High/Low-Beam Changer. See
Headlamp High/Low-Beam Changer on page 3-8
.
Flash-to-Pass Feature. See
Flash-to-Pass
on page 3-8
.
AUTO
Automatic Headlamps. See
Automatic
Headlamp System on page 3-15
.
Turn and Lane-Change Signals
The turn signal has one upward (for right) and
one downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up
or down. When the turn is finished, the lever will
return automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, raise or lower the lever until
the arrow starts to flash. Hold it there until you complete
the lane change. The lever will return by itself when
you release it.
As you signal a turn or a lane change, if the arrows
flash rapidly, a signal bulb may be burned out and other
drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check the fuse, see
Fuses and Circuit
Breakers on page 5-94
and for burned-out bulbs.
3-7
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your retailer for additional information
on the accessory power outlet.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would
not be covered by your warranty. Check with your
retailer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
Cigarette Lighter
Your vehicle may have a cigarette lighter. To use
the lighter, located on the instrument panel below
the climate controls, push it in all the way and let go.
When it is ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
Notice:
If you put papers, pins, or other flammable
items in the ashtray, hot cigarettes or other
smoking materials could ignite them and possibly
damage your vehicle. Never put flammable items
in the ashtray.
3-18
Oil Pressure Light
If you have a low engine
oil pressure problem, this
light will stay on after
you start your engine,
or come on when you are
driving. This indicates
that your engine is
not receiving enough oil.
The engine could be low on oil, or could have some
other oil problem. Have it fixed immediately.
The oil light may also come on when the ignition is on
but the engine is not running, the light will come on as a
test to show you it is working, but the light will go out
when you turn the ignition to START. If it doesn’t come
on with the ignition on, you may have a problem with
the fuse or bulb. Have it fixed right away.
{
CAUTION:
Do not keep driving if the oil pressure is low.
If you do, your engine can become so hot that
it catches fire. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced.
Notice:
Lack of proper engine oil maintenance
may damage the engine. The repairs would not be
covered by your warranty. Always follow the
maintenance schedule in this manual for changing
engine oil.
3-40
4. If your vehicle has the manual transaxle, shift your
transaxle to NEUTRAL and let the engine run for
three minutes, then turn it off.
If your vehicle has the five-speed automatic
transaxle, shift your transaxle from AUTOMATIC
OVERDRIVE (D) to NEUTRAL (N) and let the
engine run for three minutes. Then turn it off.
Due to transaxle fluid drain back, the transaxle
lubrication procedure in Step 4 is required every
seven hours after the initial procedure has
been completed, regardless of the vehicle being
towed or parked. Once the procedure is performed,
the transaxle is adequately lubricated and can
be recreational vehicle towed for seven hours
prior to repeating the lubrication procedure.
As an example, if you initially perform the lubrication
procedure and tow your vehicle for three hours,
then park for four hours, the lubrication procedure
will need to be performed again, prior to dinghy
towing the vehicle.
Notice:
Towing your vehicle after shifting the
automatic transaxle (four-speed or five-speed) from
anything other than AUTOMATIC OVERDRIVE (D)
to NEUTRAL (N) can cause internal damage
to the automatic transaxle. Always shift the
automatic transaxle (four-speed or five-speed)
from AUTOMATIC OVERDRIVE (D) to NEUTRAL (N)
as the last shift before towing.
5. Locate and remove the large IGN fuse from the
underhood fuse block. See
Underhood Fuse
Block on page 5-96
.
Notice:
If you tow your vehicle without performing
each of the steps listed under “Dinghy Towing,”
you could damage the automatic transaxle. Be sure
to follow all steps of the dinghy towing procedure
prior to and after towing your vehicle.
Notice:
If your vehicle has a four-speed automatic
transaxle, it can be dinghy towed from the front
for unlimited miles at 65 mph (105 km/h). If you
exceed 65 mph (105 km/h) while towing your
vehicle, it could be damaged. The repairs would
not be covered by your warranty. Never exceed
65 mph (105 km/h) while towing your vehicle.
Notice:
If your vehicle has a five-speed automatic
transaxle and it is towed for more than seven hours
without performing lubrication process or at
speeds greater than 65 mph (105 km/h), you could
damage the automatic transaxle. The repairs
would not be covered by your warranty. Do not
tow your vehicle for extended periods of time or
at speeds greater than 65 mph (105 km/h).
After seven hours, repeat Step 4 above for the
five-speed automatic transaxle.
4-50
Once you have reached your destination, do the
following:
1. Set the parking brake.
2. Shift the transaxle to REVERSE (R) for manual
transaxle.
3. Turn the ignition key to LOCK and remove the
key from the ignition.
4. Reinstall the large IGN fuse.
Notice:
Too much or too little fluid can damage
the transaxle. Be sure that the transaxle fluid is
at the proper level before towing with all four wheels
on the ground.
Notice:
Don’t tow a vehicle with the front drive
wheels on the ground if one of the front tires is
a compact spare tire. Towing with two different tire
sizes on the front of the vehicle can cause severe
damage to the transaxle.
Dolly Towing
(All-Wheel-Drive Vehicles)
All-wheel-drive vehicles should not be towed with
two wheels on the ground. To properly tow these
vehicles, they should be placed on a platform trailer
with all four wheels off of the ground or dinghy
towed from the front.
Dolly Towing
(Front-Wheel-Drive Vehicles)
To tow your front-wheel-drive vehicle from the front with
two wheels on the ground, do the following:
1. Put the front wheels on a dolly.
2. If you have a five-speed automatic transaxle or
four-speed automatic transaxle, move the shift
lever to PARK (P). If you have a manual transaxle,
move the shift lever to SECOND (2).
3. Set the parking brake and then remove the key.
4. Clamp the steering wheel in a straight-ahead
position with a clamping device designed for towing.
5. Release the parking brake.
4-51
A. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-21
.
B. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-15
.
C. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-15
.
D. Remote Negative (
) Terminal. See
Jump Starting
on page 5-42
.
E. Brake/Clutch Cylinder Fluid. See
Brakes on
page 5-38
and
Hydraulic Clutch on page 5-27
.
F. Underhood Fuse Block. See
Underhood Fuse Block
on page 5-96
.
G. Battery. See
Battery on page 5-41
.
H. Remote Positive (+) Terminal. See
Jump Starting
on page 5-42
.
I. Engine Coolant Surge Tank. See “Checking Coolant”
under
Engine Coolant on page 5-27
.
J. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-37
.
5-13
A. Engine Air Cleaner/Filter. See
Engine
Air Cleaner/Filter on page 5-21
.
B. Engine Oil Dipstick (Out of View). See “Checking
Engine Oil” under
Engine Oil on page 5-15
.
C. Engine Oil Fill Cap (Out of View). See “When to
Add Engine Oil” under
Engine Oil on page 5-15
.
D. Remote Negative (
) Terminal. See
Jump Starting
on page 5-42
.
E. Battery. See
Battery on page 5-41
.
F. Underhood Fuse Block. See
Underhood Fuse
Block on page 5-96
.
G. Remote Positive (+) Terminal (Out of View).
See
Jump Starting on page 5-42
.
H. Engine Coolant Surge Tank. See “Checking Coolant”
under
Engine Coolant on page 5-27
.
I. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-37
.
Engine Oil
Checking Engine Oil
It is a good idea to check your engine oil every time you
get fuel. In order to get an accurate reading, the oil
must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop for
the 2.2L L4 engine and an orange loop for the
3.5L V6 engine. See
Engine Compartment Overview
on page 5-12
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil several
minutes to drain back into the oil pan. If you do
not do this, the oil dipstick might not show the
actual level.
2. Pull out the dipstick and clean it with a paper towel
or cloth, then push it back in all the way. Remove it
again, keeping the tip down, and check the level.
5-15
Notice:
If you leave your radio or other accessories
on during the jump starting procedure, they could
be damaged. The repairs would not be covered
by your warranty. Always turn off your radio and
other accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or the accessory power outlet. Turn off
the radio and all lamps that are not needed. This
will avoid sparks and help save both batteries.
And it could save the radio!
4. Open the hood on the other vehicle and locate the
positive (+) and negative (
) terminal locations on
that vehicle.
Open the hood on your vehicle and find the remote
positive (+) and remote negative (
) jump starting
terminals.
A. Remote Positive
B. Remote Negative
A vehicle that has the 2.2L L4 engine, the remote
positive (+) terminal is located in the engine
compartment on the driver’s side of the vehicle,
on the underhood fuse block. See
Engine
Compartment Overview on page 5-12
for more
information on location.
Access the remote positive (+) terminal by removing
the fuse block cover.
The remote negative (
) terminal is the lift hook,
which is located towards the rear of the engine
on the driver’s side.
2.2L L4 Engine
5-43
To disconnect the jumper cables from both vehicles,
do the following:
1. Disconnect the black negative (
) cable from the
vehicle that had the dead battery.
2. Disconnect the black negative (
) cable from the
vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the
other vehicle.
5. Return the underhood fuse block cover to its
original position, if needed.
All-Wheel Drive
If you have an all-wheel-drive vehicle, be sure to
perform the lubricant checks described in this section.
There are two additional systems that need lubrication.
Transfer Case (3.5L V6 Engine)
When to Check and Change Lubricant
Refer to the Maintenance Schedule to determine how
often to check the lubricant and when to change it.
See
Scheduled Maintenance on page 6-4
.
How to Check Lubricant
A. Fill Plug
B. Drain Plug
To get an accurate reading, the vehicle should be on a
level surface.
If the level is below the bottom of the filler plug hole,
located on the transfer case, you’ll need to add some
lubricant. Add enough lubricant to raise the level to the
bottom of the filler plug hole. A fluid loss could indicate a
problem; check and have it repaired, if needed.
What to Use
Refer to the Maintenance Schedule to determine what
kind of lubricant to use. See
Recommended Fluids
and Lubricants on page 6-14
.
5-47
Electrical System
Add-On Electrical Equipment
Notice:
Do not add anything electrical to your
vehicle unless you check with your retailer first.
Some electrical equipment can damage your vehicle
and the damage would not be covered by your
warranty. Some add-on electrical equipment can
keep other components from working as they
should.
Your vehicle has an airbag system. Before attempting
to add anything electrical to your vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-72
.
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow or ice, the wiper will stop until the motor cools.
If the overload is caused by some electrical problem,
have it fixed.
Power Windows and Other
Power Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by fuses. This greatly reduces the chance
of circuit overload and fire caused by electrical
problems.
There are two fuse blocks — the underhood fuse block,
and the instrument panel fuse block.
To identify and check fuses and relays, refer to the
Fuse Usage Chart on the inside surface of the
fuse panel door.
5-94
Instrument Panel Fuse Block
The instrument panel fuse block is located on the
passenger’s side of the lower console.
Fuses
Usage
CRUISE
Cruise Control Switch, Brake Switch
EPS
Electronic Power Steering
IGN 1
Instrument Cluster, Brake
Transmission Shift Interlock
Solenoid, Traction Switch, Fog
Lamp Switch
LOCK/MIRROR
Power Door Locks, Power Mirror,
Entry Control
BCM
Body Control Module, Front Wipers,
Windows, Sunroof
BCM (IGN 1)
Body Control Module
AIR BAG
Sensing and Diagnostic Module
RADIO (IGN)
Radio, Power Mirror,
Premium Radio Amplifier
TURN
Turn Lamps
HVAC
HVAC Control Head
HAZARD
Hazard Lamps
HTD SEATS
Heated Seats
RADIO
Radio, Data Link Connector
5-95
Fuses
Usage
PARK
Park Lamps, Taillamps, Side
Marker Lamps, License Lamps
BCM/CLUSTER
Body Control Module,
Instrument Cluster
INT LTS
Body Control Module, OnStar
®
DR LKS
Door Locks
Relays
Usage
AFTER BLOW
Not Used
HVAC
BLOWER
HVAC Control Head
PK LP
Parking Lamps
DR LCK
All Door Lock Switch
PSG DR
UNLCK
Passenger Door Unlock Switch
DRV DR
UNLCK
Driver Door Unlock Switch
HDLP
Headlamps
Underhood Fuse Block
The underhood fuse block is located in the forward part
of the engine compartment near the battery.
Fuses
Usage
ECM/TCM
Battery Voltage to ECM, TCM,
PCM (3.5L V6 (L66))
BATT FEED
Instrument Panel Fuse Box
HORN
Horn
* *
Emissions
5-96
Fuses
Usage
ABS PWR
Anti-Lock Brake System Battery
REAR DEFOG
Rear Defogger
COOL HI (L4)/
COOL 1 (V6)
Cooling Fans High (L4)/
Cooling Fan 1 (V6)
FOG LP
Fog Lamps
LH HDLP
Left Headlamp
RR WIPER
Rear Wiper
ABS
Anti-lock Brake System Module
PWR WDW
Power Window Relay and Sunroof
CIGAR/AUX2
Cigarette Lighter
HVAC
BLOWER
HVAC Blower Motor
RH HDLP
Right Headlamp
FRT WIPER
Front Wiper
ETC
Engine Control Module (ECM),
Electronic Throttle Control (V6)
SUNROOF
Sunroof Module
BRAKE
Stop Lamps
Fuses
Usage
IGN
Ignition switch
IGN/INJ (L4),
ECM/
CAM (V6)
Engine Ignition Module, Fuel
Injectors (2.2L L4 (L61))
Camshaft Sensor, Main Relay
Voltage To PCM, Ignition Coils 1-6
INJECTORS
(3.5L V6 (L66))
Fuel Injection
PWR TRAIN
Engine Control Module (ECM),
Transmission Control
Module (TCM), Transmission,
L66 Powertrain Control
Module (PCM)
BACKUP
Low Coolant Switch,
Backup Lamps (2.2L L4 (L61)),
Vehicle Speed Sensor (Manual),
Transmission Range Switch
(2.2L L4 (L61))
HTD SEATS
Heated Seats
COOL LO (L4)/
COOL 2 (V6)
Cooling Fan Low (L4),
Cooling Fan (V6)
A/C CLUTCH
Air Conditioning Clutch,
Back Up Lamps (3.5L V6 (L66))
FUEL PUMP
Fuel Pump
5-97
Fuses
Usage
AUX 1 OUTLET Front Auxiliary Power Outlet
PREM AUD
Premium Radio Amplifier
ABS
Anti-lock Brake System Ignition
PWR SEAT
Power Seats
Relays
Usage
FOG LP
Fog Lamps
COOL FAN
HI (L4)
Cooling Fan Motor High
ENG MAIN
Engine Control Module/CAM,
Emissions, Injectors,
Electronic Throttle Control
REAR DEFOG
Rear Defog System
HORN
Horn
DRL
Daytime Running Lamps
COOL FAN 1
(V6)
Cooling Fan
WIPER
SYSTEM
Wiper System
Relays
Usage
PRW WDO
Power Window Switch,
Sunroof Module
FRT WIPER
Front Wiper System
COOL FAN
LOW (L4)
Cooling Fan Motor Low
A/C CLUTCH
Air Conditioning Clutch
BACKUP
LAMPS (V6)
Back-up Lamps (V6)
FUEL PUMP
Fuel Pump System
RR WIPER
Rear Wiper System
COOL FAN 2
(V6)
Cooling Fan (V6)
Misc.
Usage
FUSE PULLER
Fuse Puller
Diode
Air Conditioning Diode
5-98