Saturn L-Series - 2005 Fuse Box Diagram

Saturn L-Series - 2005 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
Turn and Lane-Change Signals
Headlamps
Headlamp High/Low-Beam Changer
Flash-to-Pass Feature
Turn and Lane-Change Signals
The turn signal has an upward (for right) and a
downward (for left) position. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, raise or lower the lever until
the arrow starts to flash. Hold it there until you complete
the lane change. The lever will return by itself when
you release it.
As you signal a turn or a lane change, if the arrows
flash rapidly, a signal bulb may be burned out and other
drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check the fuse, see
Fuses and Circuit
Breakers on page 5-83
and for burned-out bulbs.
3-7
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information
on the accessory power outlet.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
Ashtrays and Cigarette Lighter
Your vehicle may have an ashtray and cigarette lighter.
To use the lighter, just push it in all the way and let
go. When it’s ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating. Do not
use anything other than the cigarette lighter in the
heating element.
To remove the ashtray, lift it straight up. To reinstall it,
press the ashtray down firmly until it is fully seated.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
3-17
The oil light may also come on when the ignition is on
but the engine is not running, the light will come on as a
test to show you it is working, but the light will go out
when you turn the ignition to START. If it doesn’t come
on with the ignition on, you may have a problem with
the fuse or bulb. Have it fixed right away.
{
CAUTION:
Do not keep driving if the oil pressure is low.
If you do, your engine can become so hot that
it catches fire. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced.
Notice:
Lack of proper engine oil maintenance
may damage the engine. The repairs would not
be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
Change Engine Oil Light
If this light comes on and
stays on, it means that
service is required for
your vehicle.
See
Scheduled Maintenance on page 6-4
and/or
Engine
Oil on page 5-13
for more information.
Security Light
Your vehicle is equipped
with a Passlock
®
theft-deterrent system.
With this system, the
security light will flash
as you open the door if
your ignition is off.
For more information, see
Passlock
®
on page 2-14
.
3-34
Setting Preset Stations
Up to 18 stations (six FM1, six FM2, and six AM), can
be programmed on the six numbered pushbuttons,
by performing the following steps:
1. Turn the radio on.
2. Press AM FM to select FM1, FM2, or AM.
3. Tune in the desired station.
4. Press and hold one of the six numbered
pushbuttons until you hear a beep. Whenever
that numbered pushbutton is pressed, the station
that was set will return.
5. Repeat the steps for each pushbutton.
If the battery has been disconnected or a radio fuse
has been removed, the preset stations and time of day
will need to be reset.
Using Automatic Set
A.SET (Automatic Set):
Press this button to have
the radio automatically select the first 12 strongest
radio stations for FM and the six strongest radio
stations for AM.
To select the stations, perform the following:
1. Press AM FM to select FM1, FM2, or AM.
2. Press and hold AM FM until you hear a beep.
The radio will begin to search the current band.
The radio will store the stations, starting from the
lowest frequency, to each preset pushbutton. A.SET
will appear on the display when the radio is
finished storing the stations.
Cancelling Automatic Set
The radio retains the previously stored stations so they
can be recalled when automatic set is canceled.
Press and hold A.SET until you hear a beep. A.SET will
no longer appear on the display.
Setting the Tone (Bass/Treble)
MODE:
Press this button until BAS or TRE appears
on the display. Press the plus or minus buttons to
increase or to decrease. The display will show the bass
or the treble level. If a station is weak or noisy,
decrease the treble.
3-40
Setting Preset Stations
Up to 18 stations (six FM1, six FM2, and six AM), can
be programmed on the six numbered pushbuttons,
by performing the following steps:
1. Turn the radio on.
2. Press AM FM to select FM1, FM2, or AM.
3. Tune in the desired station.
4. Press the AUTO TONE arrow to select the
equalization.
5. Press and hold one of the six numbered
pushbuttons until you hear a beep. Whenever that
numbered pushbutton is pressed, the station
that was set will return and the equalization that
was selected will be stored for that pushbutton.
6. Repeat the steps for each pushbutton.
If the battery has been disconnected or a radio fuse has
been removed, the preset stations and time of day
will need to be reset.
Using Automatic Set
A.SET (Automatic Set):
Press this button to have the
radio automatically select the first 12 strongest radio
stations for FM and the six strongest radio stations
for AM.
To select the stations, perform the following:
1. Press AM FM to select FM1, FM2, or AM.
2. Press and hold AM FM until you hear a beep.
The radio will begin to search the current band.
The radio will store the stations, starting from the
lowest frequency, to each preset pushbutton. A.SET
will appear on the display when the radio is
finished storing the stations.
Cancelling Automatic Set
The radio retains the previously stored stations so they
can be recalled when automatic set is canceled.
Press and hold A.SET until you hear a beep. A.SET will
no longer appear on the display.
3-44
Dinghy Towing
You may dinghy tow your vehicle from the front following
these steps:
1. Set the parking brake.
2. Turn the ignition key to ACC to unlock
the steering wheel.
3. Shift your transaxle to NEUTRAL (N).
4. Open the lid on the underhood fuse block and
remove the IGN 0/3/CR and IGN 1/2 fuses.
Refer to the underside of the underhood fuse block
cover for specific fuse locations.
5. Close the lid on the underhood fuse block and store
the two fuses in a safe place.
6. Close the hood.
7. Release the parking brake.
Once you have reached your destination replace the
IGN 0/3/CR and IGN 1/2 fuses.
Notice:
If you exceed 65 mph (110 km/h) while
towing your vehicle, it could be damaged. Never
exceed 65 mph (110 km/h) while towing your vehicle.
4-38
Electrical System
Add-On Electrical Equipment
Notice:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle and
the damage wouldn’t be covered by your warranty.
Some add-on electrical equipment can keep other
components from working as they should.
Your vehicle has an airbag system. Before attempting to
add anything electrical to your vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-54
.
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow or ice, the wiper will stop until the motor cools.
If the overload is caused by some electrical problem,
have it fixed.
Power Windows and Other Power
Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by fuses. This greatly reduces the chance
of circuit overload and fire caused by electrical
problems.
There are three fuse blocks — the underhood fuse
block, the driver’s side floor console fuse block and the
passenger’s side floor console fuse block.
To identify and check fuses and relays, refer to the
Fuse Usage Chart on the inside surface of the
fuse panel door.
5-83
Floor Console Fuse Block
The driver’s side instrument panel is located under the
instrument panel on the driver’s left side.
Use a key or a coin to remove the fuse panel door and
access the fuses and relays.
Fuses
Usage
DIMMER
Dimmer Switch
IGN 3
Left Heated Seat Switch
(If Equipped), Right Heated
Seat Switch (If Equipped), Air
Conditioning, Rear Defogger Relay
DEFOG LED
Rear Defog LED
RR COMP
Trunk Compartment Lamp
WIPER
Windshield Washers and
Wipers (Front)
BTSI/BCM/
MIRROR
Brake Transaxle Shift Interlock,
Body Control Module, Power Mirror
RADIO
Audio, OnStar
®
, Rear Seat DVD
(Option)
Relays
Usage
IGN 3
Ignition Switch
REAR DEFOG
Rear Defogger
HEADLAMP
Headlamps
PARKLAMP
Park Lamps
Misc.
Usage
FUSE PULLER
Fuse Puller
5-84
The passenger’s side fuse block is located under the
instrument panel on the passenger’s right side.
Use a key or a coin to remove the fuse panel door and
access the fuses and relays.
Fuses
Usage
LOCKS
Power Door Locks
HTD SEAT
Heated Seats (If Equipped)
BODY
Power Door Locks, Heated Mirror
Relay, Liftgate Latch
POWER SEAT
Power Seat
PREM AMP
Premium Sound System Amplifier
FOG LAMP
Fog Lamps
RR WIPER/
SUNROOF
Rear Wiper/Washer (Wagon),
Sunroof
Relays
Usage
DR UNLOCK
Driver Door Unlock
UNLOCK
Door Unlock
LOCK
Door Lock
MIRROR
Power Mirrors
FOG LAMP
Fog Lamps
WINDOW
Power Windows, Power Sunroof
Misc.
Usage
FUSE PULLER
Fuse Puller
5-85
Engine Compartment Fuse Block
The engine compartment
fuse block is located in
the forward part of
the engine compartment
near the battery.
Fuses
Usage
IGN 0/3/CR (L4) Ignition Switch
RADIO
Audio System, OnStar
®
, Rear Seat
DVD (Option)
BCM CLUSTER
Body Control Module, Instrument
Cluster, Dimmer Switch
INJECTOR (L4)
Fuel Injectors (2.2L L4, If Equipped)
IGN (V6)
EIS (L4)
Ignition Coils (3.0L V6)
Electronic Ignition System
(2.2L L4, If Equipped)
5-86
Fuses
Usage
FUEL PUMP
Fuel Pump System
RT HEADLAMP Right Headlamps
BRAKE
Brake Lamps
IGN 1
Instrument Cluster, Coolant Level
Switch, Air Bag, Electronic
PRND321
HAZARD
Hazard Flasher, HBTT (Headlamp
HI Beam Indicator), I/P Cluster
ABS 2
Anit-Lock Brake System
CONTROLS
IGN 1
Cooling Fan Control Module,
Powertrain Control Module,
Transaxle (2.2L L4, If Equipped),
Transaxle Control Module (3.0L V6)
BACK-UP/TURN
Backup Lamps, Coolant
Level Switch
CRUISE SW
Cruise Control Switch
BCM/ECM/
CRUISE
Body Control Module, Engine
Control Module, Cruise Control, ABS
ABS 1
Anit-Lock Brake System
Fuses
Usage
ENGINE
CNTL 3 (V6)
3.0L V6 Engine
REAR DEFOG
Rear Window Defogger
HVAC
BLOWER
High Blower
IGN 0
Park Neutral Position Switch,
Powertrain Control Module
AC
Air Conditioning System
CD/DLC
Audio, Data Link Connector, (DLC),
Rear Seat DVD (Option)
IGN 1/2
Ignition switch
HORN
Horn
CONTROLS B+
Powertrain Control Module (2.2L L4,
If Equipped), Engine Control Module
(3.0L V6), Transaxle Control Module
(3.0L V6)
I/P BATT RT
Passenger’s Side Instrument Panel
Fuse Block
AUX PWR
Power Outlet
5-87
Fuses
Usage
COOL FAN 2
Cooling fan module
ENGINE
CNTL (V6)
3.0L V6 (L81) Engine
ENGINE
CNT (V6)
IGN 3 (L4)
3.0L V6 Engine
Cruise Clutch Switch, Emissions
Controls, Air Conditioner Relay,
Heated Oxygen Sensor
BCM 2
Body Control Module
PARK LAMP
Front Park Lamps, Taillamps, Front
Marker Lamps, Rear Marker
Lamps, License Lamps, Radio
Display Lights, I/P Cluster
Backlighting, I/P Dimmer, Cigar
Lighter Ring, Ashtray Light,
PRND321 Light, Climate Control
Switch Backlighting
COOL FAN 1
Cooling Fan Module
LT
HEADLAMP
Left Headlamps
LIGHTER
Cigarette Lighter
Relays
Usage
FUEL PUMP
Fuel Pump System
WIPER
Wiper System
AC
Air Conditioning System
HORN
Horn
REAR WIPER
Rear Wiper System (Wagon Only)
MAIN (V6)
3.0L V6 Engine
DRL
Daytime Running Lamp
Circuit
Breakers
Usage
WDO/SUNRF
(V6)
Power Window Relay, Sunroof
(3.0L V6)
WDO/SUNRF
(L4)
Power Window Relay, Sunroof and
Air Pump Relay (2.2L L4, If
Equipped)
Diodes
Usage
§
Air Conditioner Diode
Fuses
Usage
FUSE PULLER
Fuse Puller
5-88