Pontiac Bonneville - 2005 Fuse Box Diagram

Pontiac Bonneville - 2005 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
If the SECURITY light comes on for one minute and
then shuts off while the ignition is on, the security
system has detected a problem. See your dealer for
service.
If a door is opened without the key or remote keyless
entry transmitter, or if the door key cylinders are
damaged, the alarm will go off. The exterior lamps will
flash and the horn will sound for 30 seconds, then will go
off in order to save battery power.
Remember, the theft-deterrent system will not activate if
you lock the doors with a key or manual door lock. It
activates only if you use a power door lock switch while
the door is open, or the remote keyless entry
transmitter.
Avoid setting off the alarm by accident.
Always unlock a door with a key, or use the remote
keyless entry transmitter. Unlocking a door any
other way will set off the alarm.
If you set off the alarm by accident, unlock the driver’s
door with your key. You can also turn off the alarm
by pressing the button with the unlock symbol on the
remote keyless entry transmitter. The alarm will not stop
if you try to unlock a door any other way.
Testing the Alarm
1. From inside the vehicle, roll down the window.
2. Activate the system by locking the doors with the
power door lock switch while the door is open, or
with the remote keyless entry transmitter, if
equipped.
3. Get out of the vehicle, close the door and wait for
the SECURITY light to go out.
4. Then, reach in through the window, unlock the door
with the manual door lock and open the door. This
should set off the alarm.
If the alarm does not sound when it should, check to
see if the horn works. The horn fuse may be blown. To
replace the fuse, see
Fuses and Circuit Breakers on
page 5-111
.
If the alarm does not sound, or the exterior lamps do
not flash, see your dealer.
2-20
PASS-Key
®
III Operation
Your vehicle is equipped
with the PASS-Key
®
III
(Personalized Automotive
Security System)
theft-deterrent system.
PASS-Key
®
III is a passive
theft-deterrent system.
This means you do not have to do anything different to
arm or disarm the system. It works when you insert
or remove the key from the ignition.
When the PASS-Key
®
III system senses that someone
is using the wrong key, it shuts down the vehicle’s
starter and fuel systems. The starter will not work and
fuel will stop being delivered to the engine. Anyone
using a trial-and-error method to start the vehicle will be
discouraged because of the high number of electrical
key codes.
When trying to start the vehicle, if the engine does not
start and the SECURITY light comes on, the key
may have a damaged transponder. Turn the ignition off
and try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse. See
Fuses
and Circuit Breakers on page 5-111
. If the engine still
does not start with the other key, your vehicle needs
service. If your vehicle does start, the first key may be
faulty. See your dealer who can service the
PASS-Key
®
III to have a new key made.
It is possible for the PASS-Key
®
III decoder to learn the
transponder value of a new or replacement key. Up
to 10 keys may be programmed for the vehicle.
This procedure is for programming additional keys only.
Canadian Owners:
If you lose or damage your
keys, only a GM dealer can service PASS-Key
®
III to
have new keys made. To program additional keys
you will require two current driver’s keys. You must add
a step to the following procedure. After Step 2 repeat
Steps 1 and 2 with the second current driver’s key. Then
continue with Step 3.
2-22
Turn and Lane-Change Signals
The turn signal has two upward for right, and two
downward for left, positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by itself
when you release it.
If the arrows flash very fast as you signal a turn or a
lane change, a signal bulb may be burned out and other
drivers will not see your turn signal. If a bulb is burned
out, replace it to help avoid an accident. See
Bulb
Replacement on page 5-67
.
If the arrows do not go on at all when you signal a turn,
check the fuse. See
Fuses and Circuit Breakers on
page 5-111
.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile
(1.2 km), a chime will sound at each flash of the
turn signal. To turn off the chime, move the turn signal
lever to the off position.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high
beam, push the lever forward. To change from high
beam to low beam, pull the turn signal lever toward you,
then release it.
3-8
Accessory Power Outlets
With the accessory power outlet you can plug in
auxiliary electrical equipment such as a cellular
telephone or CB radio.
If your vehicle has a front console, the 12-volt accessory
power outlet is located at the rear of the front console.
If your vehicle has a floor console, the outlet is
located at the rear of the floor console.
To use the outlet, remove the protective cap which
covers it. When not using it, always cover the outlet with
the protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information
on accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
proper installation instructions included with the
equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
Ashtrays and Cigarette Lighter
Push down on the cover to reveal the front ashtray.
To clean the ashtray, lift it out by pulling on the finger
holes on each side.
On models without a console, an ashtray is located
underneath the instrument panel. To clean the ashtray,
lift it out by pulling up on the tabs on either side. It
snaps back into place.
3-24
To open a rear ashtray, lift the cover.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
The cigarette lighter is located next to the storage tray.
To use a lighter, just push the center in all the way
and let it go. When it is ready, the center will pop back
out by itself. Pull out the entire unit to use it.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating. Do not
use anything other than the cigarette lighter in the
heating element.
Climate Controls
Climate Control System
With this system you can control the heating, cooling
and ventilation for your vehicle.
FAN:
Turn the left knob clockwise or counterclockwise
to increase or decrease the fan speed. Push this
knob to turn the fan on and off. The fan must be on in
order for the air conditioning compressor to run.
TEMP (Temperature Control):
Turn the right knob
clockwise or counterclockwise to manually increase or
decrease the temperature inside your vehicle.
3-25
A. Engine Compartment Fuse Block. See
Engine
Compartment Fuse Block (3.8L V6 Engine) on
page 5-112
or
Engine Compartment Fuse Block
(4.6L V8 Engine) on page 5-114
.
B. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-53
.
C. Engine Coolant Recovery Tank. See “Checking
Coolant” under
Engine Coolant (3.8L V6 Engine)
on page 5-31
or
Engine Coolant (4.6L V8 Engine)
on page 5-34
.
D. Radiator Pressure Cap. See
Radiator Pressure Cap
(3.8L V6 Engine) on page 5-36
.
E. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-52
.
F. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-16
.
G. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-16
.
H. Automatic Transaxle Fluid Dipstick. See “Checking
the Fluid Level” under
Automatic Transaxle Fluid
(3.8L V6 Engine) on page 5-25
or
Automatic
Transaxle Fluid (4.6L V8 Engine) on page 5-28
.
I. Brake Master Cylinder. See “Brake Fluid” under
Brakes on page 5-54
.
J. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter (3.8L V6 Engine) on page 5-22
or
Engine Air Cleaner/Filter (4.6L V8 Engine) on
page 5-23
.
5-13
A. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 5-53
.
B. Engine Compartment Fuse Block. See
Engine
Compartment Fuse Block (3.8L V6 Engine) on
page 5-112
or
Engine Compartment Fuse Block
(4.6L V8 Engine) on page 5-114
.
C. Engine Coolant Surge Tank and Pressure Cap.
See
Coolant Surge Tank Pressure Cap
(4.6L V8 Engine) on page 5-36
and
Cooling System
(3.8L V6 Engine) on page 5-40
or
Cooling System
(4.6L V8 Engine) on page 5-47
.
D. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-52
.
E. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 5-16
.
F. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 5-16
.
G. Brake Master Cylinder. See “Brake Fluid” under
Brakes on page 5-54
.
H. Automatic Transaxle Fluid Cap and Dipstick.
See “Checking the Fluid Level” under
Automatic
Transaxle Fluid (3.8L V6 Engine) on page 5-25
or
Automatic Transaxle Fluid (4.6L V8 Engine) on
page 5-28
.
I. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter (3.8L V6 Engine) on page 5-22
or
Engine Air Cleaner/Filter (4.6L V8 Engine) on
page 5-23
.
5-15
Replacing Brake System Parts
The braking system on a vehicle is complex. Its many
parts have to be of top quality and work well together if
the vehicle is to have really good braking. Your vehicle
was designed and tested with top-quality GM brake
parts. When you replace parts of your braking
system —for example, when your brake linings wear
down and you need new ones put in — be sure you get
new approved GM replacement parts. If you do not,
your brakes may no longer work properly. For example,
if someone puts in brake linings that are wrong for
your vehicle, the balance between your front and rear
brakes can change — for the worse. The braking
performance you have come to expect can change in
many other ways if someone puts in the wrong
replacement brake parts.
Battery
Your vehicle has a maintenance free battery. When it is
time for a new battery, get one that has the replacement
number shown on the original battery’s label.
We recommend an ACDelco
®
replacement battery.
Warning:
Battery posts, terminals and related
accessories contain lead and lead compounds,
chemicals known to the State of California to cause
cancer and reproductive harm. Wash hands after
handling.
The battery is located under the rear seat cushion.
To access the battery, see “Removing the Rear Seat
Cushion” under
Rear Underseat Fuse Block on
page 5-116
. You do not need to access the battery to
jump start your vehicle. See
Jump Starting (3.8L V6
Engine) on page 5-59
or
Jump Starting (4.6L V8 Engine)
on page 5-63
.
{
CAUTION:
A battery that is not properly vented can let
sulfuric acid fumes into the area under the rear
seat cushion. These fumes can damage your
rear seat safety belt systems. You may not be
able to see this damage, and the safety belts
might not provide the protection needed in a
crash. If a replacement battery is ever needed,
it must be vented in the same manner as the
original battery. Always make sure that the
vent hose is properly reattached before
reinstalling the seat cushion.
5-57
Electrical System
Add-On Electrical Equipment
Notice:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle and
the damage wouldn’t be covered by your warranty.
Some add-on electrical equipment can keep other
components from working as they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see
Servicing
Your Airbag-Equipped Vehicle on page 1-56
.
Headlamp Wiring
The headlamp wiring is protected by an internal circuit
breaker. An electrical overload will cause the lamps to
go on and off, or in some cases to remain off. If this
happens, have your headlamp system checked
right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an internal
circuit breaker and a fuse. If the motor overheats due to
heavy snow, etc., the wiper will stop until the motor
cools. If the overload is caused by some electrical
problem, have it fixed.
Power Windows and Other
Power Options
Circuit breakers in the rear fuse block protect the power
windows and other power accessories. When the
current load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed
or goes away.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of damage
caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
The MaxiFuses are located in two fuse blocks, one in
the engine compartment and the other under the
rear seat. If a MaxiFuse should blow, have your vehicle
serviced by your dealer immediately.
Removing Fuses
You will find a fuse puller attached in both of the fuse
blocks. Snap the wide end of the fuse puller on to
the fuse at the side indentations, then hold the puller
and pull the fuse out.
5-111
Engine Compartment Fuse Block
(3.8L V6 Engine)
The engine compartment
fuse block is located in the
front of the engine
compartment on the
passenger’s side of the
vehicle. See
Engine
Compartment Overview on
page 5-12
for more
information on location. Lift
the cover to gain access.
Fuses
Usage
1
Not Used
2
Accessory
3
Windshield Wipers
4
Not Used
5
Headlamp Low-Beam Left
6
Headlamp Low-Beam Right
7
Spare
8
Powertrain Control Module Battery
9
Headlamp High-Beam Right
10
Headlamp High-Beam Left
11
Ignition 1
12
Not Used
13
Transaxle
5-112
Fuses
Usage
14
Cruise Control
15
Direct Ignition System
16
Injector Bank #2
17
Not Used
18
Not Used
19
Powertrain Control Module Ignition
20
Oxygen Sensor
21
Injector Bank #1
22
Auxiliary Power
23
Cigar Lighter
24
Fog Lamps/Daytime Running Lamps
25
Horn
26
Air Conditioning Clutch
Relays
Usage
27
Headlamp High Beam
28
Headlamp Low Beam
29
Fog Lamps
30
Daytime Running Lamps
31
Horn
32
Air Conditioning Clutch
33
HVAC Solenoid
34
Accessory
Relays
Usage
35
Not Used
36
Starter 1
37
Cooling Fan 1
38
Ignition 1
39
Cooling Fan Series/Parallel
40
Cooling Fan 2
Circuit
Breakers
Usage
41
Starter
Fuses
Usage
42
Not Used
43
Not Used
44
Antilock Brake System
45
Not Used
46
Cooling Fan 1
47
Cooling Fan 2
48
Spare
49
Spare
50
Spare
51
Spare
52
Spare
53
Fuse Puller
5-113
Engine Compartment Fuse Block
(4.6L V8 Engine)
The engine compartment
fuse block is located next
to the engine on the
passenger’s side of the
vehicle. For more
information on location,
see
Engine Compartment
Overview on page 5-12
.
To access the fuses, push in the two tabs located at
each end of the fuse block cover. Then lift the cover off.
Fuses
Usage
1
Assembly Line Diagnostic Link
2
Accessory
3
Windshield Wipers
4
Not Used
5
Headlamp Low-Beam Left
6
Headlamp Low-Beam Right
7
Instrument Panel
8
Powertrain Control Module Battery
9
Headlamp High-Beam Right
10
Headlamp High-Beam Left
11
Ignition 1
5-114
Fuses
Usage
12
Fog Lamps
13
Transaxle
14
Cruise Control
15
Coil Module
16
Injector Bank #2
17
Not Used
18
Not Used
19
Powertrain Control Module Ignition
20
Oxygen Sensor
21
Injector Bank #1
22
Cigar Lighter #2
23
Cigar Lighter #1
24
Daytime Running Lamps
25
Horn
26
Air Conditioner Clutch
42
Not Used
43
Not Used
44
Anti-Lock Brake System
45
Air Pump
46
Cooling Fan 1
47
Cooling Fan 2
54
Spare
Relays
Usage
27
Headlamp High Beam
28
Headlamp Low Beam
29
Fog Lamps
30
Daytime Running Lamps
31
Horn
32
Air Conditioner Clutch
33
Air Control Valve
34
Spare
35
Accessory
36
Starter 1
37
Cooling Fan 1
38
Ignition 1
39
Cooling Fan Series/Parallel
40
Cooling Fan 2
Circuit
Breakers
Usage
41
Starter
The spare fuses are located in numbers 48 through 52.
The fuse puller is located in number 53.
5-115
Rear Underseat Fuse Block
The rear fuse block is
located below the rear seat
on the driver’s side of
the vehicle. The rear seat
cushion must be
removed to access the
fuse block. See “Removing
the Rear Seat Cushion”
following for more
information.
Fuses
Usage
1
Fuel Pump
2
Heater, Ventilation, Air Conditioning
Blower
3
Memory Seat
4
Assembly Line Diagnostic Link
5
Not Used
6
Compact Disc (CD)
7
Driver Door Module
8
Supplemental Inflatable Restraint
9
Not Used
10
Lamps Park Right
11
Ventilation Solenoid
12
Ignition 1
5-116
Fuses
Usage
13
Lamps Park Left
14
Interior Lamp Dimmer Module
15
Satellite Digital Radio
16
Heated Seat Left Front
17
Not Used
18
Rear Door Modules
19
Stoplamps
20
PARK (P) / REVERSE (R)
21
Audio
22
Retained Accessory Power
23
Not Used
24
Not Used
25
Passenger Door Module
26
Body
27
Interior Lamps
28
Not Used
29
Ignition Switch
30
Instrument Panel
31
Heated Seat Right Front
32
Not Used
33
Heating, Ventilation, Air Conditioning
34
Ignition 3 Rear
35
Antilock Brake System
Fuses
Usage
36
Turn Signal/Hazard
37
HVAC Battery
38
Dash Integration Module
Relays
Usage
39
Fuel Pump
40
Parking Lamps
41
Ignition 1
42
Rear Fog Lamps
43
Not Used
44
Park Brake
45
Reverse Lamps
46
Retained Accessory Power
48
Not Used
49
Ignition 3
51
Interior Lamps
52
Trunk Release
53
Front Courtesy Lamps
54
Not Used
55
Electronic Level Control Compressor
5-117
Circuit
Breakers
Usage
56
Power Seats
57
Power Windows
Relays
Usage
58
Not Used
59
Rear Defog
Fuses
Usage
60
Not Used
61
Rear Defog
62
Not Used
63
Audio Amplifier
Fuses
Usage
64
Electronic Level Control
Compressor/Exhaust
65
Not Used
66
Not Used
67
Not Used
68
Not Used
69
Spare
70
Spare
71
Spare
72
Spare
73
Spare
74
Spare
75
Fuse Puller
5-118
Removing the Rear Seat Cushion
Notice:
If you touch the exposed wires with the
metal on the seat cushion, you could cause a
short that could damage the battery and or wires.
Avoid contact between the rear seat and the
fuse center whenever you remove or reinstall the
rear seat. Do not remove covers from any of
the covered parts, and do not store anything under
the seats.
To remove the rear seat cushion, do the following:
1. Pull up on the front of the cushion to release the
front hooks.
2. Pull the cushion up and out toward the front of the
vehicle.
To reinstall the rear seat cushion, do the following:
{
CAUTION:
A safety belt that is not properly routed
through the seat cushion or is twisted will not
provide the protection needed in a crash. If the
safety belt has not been routed through the
seat cushion at all, it will not be there to work
for the next passenger. The person sitting in
that position could be badly injured. After
reinstalling the seat cushion, always check to
be sure that the safety belts are properly
routed and are not twisted.
5-119