Saturn VUE - 2004 Fuse Box Diagram

Saturn VUE - 2004 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, raise or lower the lever until
the arrow starts to flash. Hold it there until you complete
the lane change. The lever will return by itself when
you release it.
As you signal a turn or a lane change, if the arrows
flash rapidly, a signal bulb may be burned out and other
drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check the fuse, see
Fuses and Circuit
Breakers on page 5-98
and for burned-out bulbs.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high or
high beam to low, pull the turn signal lever all the way
towards you. Then release it.
When the high beams
are on, this light on the
instrument panel cluster
will also be on.
Flash-to-Pass
This feature lets you use your high-beam headlamps to
signal a driver in front of you that you want to pass.
To use it, pull the turn signal/multifunction lever toward
you until the high-beam headlamps come on, then
release the lever to turn them off.
Headlamps
The exterior lamp control is located on the turn
signal/multifunction lever.
O
(Exterior Lamp Control):
Turn the control with this
symbol on it to operate the exterior lamps.
3-8
Map Lamps
The lamps are located on the headliner above the
rearview mirror. To turn the lamps on, press the lens.
Press the lens again to turn them off.
Battery Run-Down Protection
Your vehicle is equipped with a battery saver feature
designed to protect your vehicle’s battery.
When any interior lamp is left on and the ignition is
turned off, the battery rundown protection system will
automatically turn the lamp off after 20 minutes. This
will avoid draining the battery.
Accessory Power Outlets
The accessory power outlets can be used to connect
electrical equipment such as a cellular phone or
CB radio.
The accessory power outlets are located on the
instrument panel near the climate controls and on the
rear of the center console.
To use the outlets, remove the cover. When not in use,
always cover the outlet with the protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your retailer for additional information
on the accessory power outlet.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-20
Oil Pressure Light
If you have a low engine
oil pressure problem, this
light will stay on after
you start your engine, or
come on when you
are driving. This indicates
that your engine is not
receiving enough oil.
The engine could be low on oil, or could have some
other oil problem. Have it fixed immediately.
The oil light may also come on when the ignition is on
but the engine is not running, the light will come on as a
test to show you it is working, but the light will go out
when you turn the ignition to START. If it doesn’t come
on with the ignition on, you may have a problem with
the fuse or bulb. Have it fixed right away.
{
CAUTION:
Do not keep driving if the oil pressure is low.
If you do, your engine can become so hot that
it catches fire. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced.
Notice:
Lack of proper engine oil maintenance
may damage the engine. The repairs would not
be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
3-38
Finding a Station
AM FM:
Press this button to switch between FM1,
FM2, or AM. The display will show the selection.
R
TUNE
Q
:
Press either arrow to select radio
stations.
R
SEEK
Q
:
Press and hold the up or the down
arrow to go to the next or to the previous station and
stay there.
The radio will only seek stations with a strong signal
that are in the selected band.
SCN (Scan):
Press this button to scan stations. The
radio will go to a station, play for a few seconds, then go
on to the next station. Press this button again to stop
scanning.
The radio will only scan stations with a strong signal
that are in the selected band.
Setting Preset Stations
Up to 18 stations (six FM1, six FM2, and six AM) can be
programmed on the six numbered pushbuttons, by
performing the following steps:
1. Turn the radio on.
2. Press AM FM to select FM1, FM2, or AM.
3. Tune in the desired station.
4. Press and hold one of the six numbered
pushbuttons until you hear a beep. Whenever that
numbered pushbutton is pressed, the station
that was set will return.
5. Repeat the steps for each pushbutton.
If the battery has been disconnected or a radio fuse has
been removed, the preset stations and time of day
will need to be reset.
Using Automatic Set
Use this feature to automatically save the radio preset
pushbuttons with the stations with the strongest
radio signals.
A.SET (Automatic Set):
Press the AM FM button to
have the radio automatically select the first 12 strongest
radio stations for FM and the six strongest radio
stations for AM.
To select the stations, perform the following:
1. Press AM FM to select FM1, FM2, or AM.
2. Press and hold AM FM until you hear a beep.
The radio will begin to search the current band.
The radio will store the stations, starting from the
lowest frequency, to each preset pushbutton. A.SET
will appear on the display when the radio is
finished storing the stations.
3-44
Finding a Station
AM FM:
Press this button to switch between FM1,
FM2, or AM. The display will show the selection.
R
TUNE
Q
:
Press the up or down arrow to select
radio stations.
R
SEEK
Q
:
Press and hold the up or the down
arrow to go to the next or to the previous station and
stay there.
The radio will only seek stations with a strong signal
that are in the selected band.
SCN (Scan):
Press this button to scan stations. The
radio will go to a station, play for a few seconds, then
go on to the next station. Press this button again to
stop scanning.
The radio will only scan stations with a strong signal
that are in the selected band.
Setting Preset Stations
Up to 18 stations (six FM1, six FM2, and six AM), can
be programmed on the six numbered pushbuttons,
by performing the following steps:
1. Turn the radio on.
2. Press AM FM to select FM1, FM2, or AM.
3. Tune in the desired station.
4. Press and hold one of the six numbered
pushbuttons until you hear a beep. Whenever that
numbered pushbutton is pressed, the station
that was set will return.
5. Repeat the steps for each pushbutton.
If the battery has been disconnected or a radio fuse has
been removed, the preset stations and time of day
will need to be reset.
Using Automatic Set
A.SET (Automatic Set):
Press the AM FM button to
have the radio automatically select the first 12 strongest
radio stations for FM and the six strongest radio
stations for AM.
To select the stations, perform the following:
1. Press AM FM to select FM1, FM2, or AM.
2. Press and hold AM FM until you hear a beep.
The radio will begin to search the current band.
The radio will store the stations, starting from the
lowest frequency, to each preset pushbutton. A.SET
will appear on the display when the radio is
finished storing the stations.
3-46
5. Press and hold one of the six numbered
pushbuttons. Preset X Stored will appear on the
display and you will hear a beep. Whenever
that numbered pushbutton is pressed, the station
that was set will return and the equalization that was
selected will be stored for that pushbutton. If the
equalization of a preset is changed while listening to
that station, the radio will save the new equalization.
6. Repeat the steps for each pushbutton.
If the battery has been disconnected or a radio fuse has
been removed, the preset stations and time of day
may need to be reset.
Using Automatic Set
A.SET (Automatic Set):
Press and hold the AM
FM button to have the radio automatically select
the first 12 strongest radio stations for FM and the
six strongest radio stations for AM.
To select the stations, perform the following:
1. Press AM FM to select FM1, FM2, or AM.
2. Press and hold AM FM until you hear a beep.
The radio will begin to search the current band.
The radio will store the stations, starting from
the lowest frequency, to each preset pushbutton.
A.SET will appear on the display when the radio
is finished storing the stations.
Cancelling Automatic Set
The radio retains the previously stored stations so they
can be recalled when automatic set is canceled.
Press and hold AM FM until you hear a beep. A.SET
will no longer appear on the display.
Setting the Tone (Bass/Treble)
Q P
(Bass/Treble):
Press this knob until BASS or
TREB appears on the display. Turn this knob to increase
or to decrease. The display will show the bass or the
treble level. If a station is weak or noisy, decrease
the treble.
q
AUTO EQ
r
(Automatic Equalization):
Press the
right and left arrow to select customized equalization
settings designed for country/western, jazz, news, pop,
rock, and classical. There is also a flat setting that
has been factory tuned for the best overall performance.
To return the bass and treble to the manual mode,
press either arrow until CUSTOM appears on the
display.
3-52
Dinghy Towing (Manual or Five-Speed
Automatic Transaxle*)
To tow your vehicle from the front with all four wheels
on the ground, do the following:
1. Position and attach the vehicle to tow it behind the
recreational vehicle.
2. Turn the ignition key to ACC.
3. Turn fog lamps and all accessories off.
4. If you have the manual transaxle, shift your
transaxle to NEUTRAL and let the engine run
for three minutes, then turn it off.
Notice:
Towing your vehicle after shifting the
five-speed automatic transaxle from anything other
than DRIVE (D) to NEUTRAL (N) can cause internal
damage to the automatic transaxle. Always shift the
five-speed automatic transaxle from DRIVE (D) to
NEUTRAL (N) as the last shift before towing.
5. If you have the automatic five-speed transaxle, shift
your transaxle from DRIVE (D) to NEUTRAL and let
the engine run for three minutes, then turn it off.
6. Locate and remove the large IGNITION fuse from
the underhood fuse block. See “Instrument Panel
Fuse Block” under
Fuses and Circuit Breakers
on page 5-98
.
Notice:
If you tow your vehicle without performing
each of the steps listed under “Dinghy Towing,”
you could damage the automatic transaxle. Be sure
to follow all steps of the dinghy towing procedure
prior to and after towing your vehicle.
Notice:
If you tow your vehicle for more than
eight hours per day or at speeds greater than
65 mph (105 km/h), you could damage the automatic
transaxle. The repairs would not be covered
by your warranty. Do not tow your vehicle for
extended periods of time or at speeds greater
than 65 mph (105 km/h).
4-47
Once you have reached your destination, do the
following:
1. Set the parking brake.
2. Shift the transaxle to FIRST (1) for manual
transaxle.
3. Turn the ignition key to LOCK and remove the
key from the ignition.
4. Replace the large IGNITION fuse.
Notice:
Too much or too little fluid can damage
the transaxle. Be sure that the transaxle fluid is
at the proper level before towing with all four wheels
on the ground.
Notice:
Don’t tow a vehicle with the front drive
wheels on the ground if one of the front tires is a
compact spare tire. Towing with two different
tire sizes on the front of the vehicle can cause
severe damage to the transaxle.
Dolly Towing (All-Wheel Drive Vehicles)
All-wheel drive vehicles should not be towed from the
front with two wheels on the ground. To properly
tow these vehicles, they should be placed on a platform
trailer with all four wheels off of the ground.
Dolly Towing (Front-Wheel Drive
Vehicles)
To tow your front-wheel drive vehicle from the front with
two wheels on the ground, do the following:
1. Put the front wheels on a dolly.
2. If you have a five-speed automatic transaxle or
VTi variable transaxle, move the shift lever to
PARK (P). If you have a manual transaxle, move
the shift lever to SECOND (2).
3. Set the parking brake and then remove the key.
4-48
A. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-21
.
B. Engine Oil Fill Cap. See
Engine Oil on page 5-15
.
C. Engine Oil Dipstick. See
Engine Oil on page 5-15
.
D. Brake/Clutch Cylinder Fluid. See
Brakes on
page 5-41
and
Hydraulic Clutch on page 5-28
.
E. Engine Compartment Fuse Block. See
Fuses and
Circuit Breakers on page 5-98
.
F. Battery. See
Battery on page 5-44
.
G. Windshield Washer Fluid Reservoir. See
Windshield
Washer Fluid on page 5-40
.
H. Engine Coolant Recovery Tank. See
Engine Coolant
on page 5-28
.
Before closing the hood, be sure all filler caps are
on properly.
5-13
A. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-21
.
B. Engine Oil Dipstick. See
Engine Oil on page 5-15
.
C. Engine Oil Fill Cap. See
Engine Oil on page 5-15
.
D. Battery. See
Battery on page 5-44
.
E. Engine Compartment Fuse Block. See
Fuses and
Circuit Breakers on page 5-98
.
F. Engine Coolant Recovery Tank. See
Engine Coolant
on page 5-28
.
G. Windshield Washer Fluid Reservoir. See
Windshield
Washer Fluid on page 5-40
.
Before closing the hood, be sure all filler caps are
on properly.
Engine Oil
Checking Engine Oil
It is a good idea to check your engine oil every time you
get fuel. In order to get an accurate reading, the oil
must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop for the
2.2L L4 engine and an orange loop for the 3.5L V6
engine. See
Engine Compartment Overview on
page 5-12
for the location of the engine oil dipstick
Turn off the engine and give the oil several minutes to
drain back into the oil pan. If you do not do this, the
oil dipstick might not show the actual level.
Pull out the dipstick and clean it with a paper towel or
cloth, then push it back in all the way. Remove it again,
keeping the tip down, and check the level.
2.2L L4 (L61) Engine
5-15
Instrument Panel Fuse Block
The instrument panel fuse block is located by the
passenger’s left leg.
Fuses
Usage
RADIO
Radio, Data Link Connector
BCM/CLSTR
Body Control Module, Instrument
Cluster
INT LTS
Body Control Module, OnStar
®
PARK
Park Lamps, Taillamps, Side Marker
Lamps, License Lamps
HZRD
Hazard Lamps
Fuses
Usage
DR LCK
Door Lock Relay
LOCK/MIRROR
Power Door Locks, Power Mirror,
Entry Control
TURN
Turn Lamps
BCM
Body Control Module, Front Wipers,
Windows, Sunroof
RADIO IGN
Radio, Power Mirror, Premium
Radio Amplifier
HVAC
HVAC Control Head
IGN 1
Instrument Cluster, BTSI Solenoid,
Traction Switch, Fog Lamp Switch
BCM (IGN)
Body Control Module
AIRBAG
SDM Module
EPS
Electronic Power Steering
CRUISE
Cruise Control Switch, Brake Switch
HTD SEATS
Heated Seats
Relays
Usage
HVAC
BLOWER
HVAC Control Head
DR LCK
All Door Lock Switch
PASS DR
UNLOCK
Passenger Door Unlock Switch
DRV DR
UNLCK
Driver Door Unlock Switch
5-99
Underhood Fuse Block
The underhood fuse block is located in the forward part
of the engine compartment near the battery.
Fuses
Usage
IGNITION
Ignition switch
BATT FEED
I/P Fuse Box
COOL 1
Cooling Fan Module
COOL
FAN HIGH
Cooling Fan High Relay
COOL
FAN LOW
Cooling Fan Low Relay
PWR WDW
Power Window Relay and Sunroof
Fuses
Usage
HVAC
BLOWER
HVAC Blower Motor
ABS
ABS Module
BRAKE
Stop Lamps
A/C CLUTCH
A/C Clutch Relay, Back Up
Lamps (3.5L V6 (L66))
SUNROOF
Sunroof Module
RR WIPER
Rear Wiper Relay
FRT WIPER
Front Wiper Relay
IGN/INJ
Engine Ignition Module, Fuel
Injectors (2.2L L4 (L61))
ABS
ABS Ignition
ABS
ABS Battery
BACKUP
Low Coolant Switch, Backup Lamps
(2.2L L4 (L61)), Vehicle Speed
Sensor (Manual), Transmission
Range Switch (2.2L L4 (L61))
PWRTRAIN
Engine Control Module (ECM),
Transmission Control Module (TCM),
Transmission
EMISS
Canister Purge Solenoid, Canister
Vent Solenoid, Rear Heated O2,
Front Heated O2
ECM/TCM
Battery Voltage to ECM, TCM, PCM
(3.5L V6 (L66))
5-100
Fuses
Usage
ECM/CAM
(3.5L V6 (L66))
Camshaft Sensor, Main Relay
Voltage To PCM, Ignition Coils 1-6
ETC (2.2L Four
Cylinder (L61))
Engine Control Module (ECM),
Electronic Throttle Control
FUEL PUMP
Fuel Pump Relay
CIGAR/AUX2
Cigar Lighter
AUX 1 OUTLET Front Auxiliary Power Outlet
FOG LP
Fog Lamp Relay
REAR DEFOG
Rear Defog Relay
HORN
Horn Relay
LH HDLP
Left Headlamp
RH HDLP
Right Headlamp
INJECTORS
(3.5L V6 (L66))
Fuel Injection
PREM AUD
Premium Radio Amplifier
HTD SEATS
Heated Seats
Relays
Usage
COOL FAN
HIGH
Cooling Fan Motor High
COOL FAN
LOW
Cooling Fan Motor Low
A/C CLUTCH
A/C Clutch
PWR WDW
Power Window Switch, Sunroof
Module
FRT WIPER
Front Wiper System
RR WIPER
Rear Wiper System
WIPER
SYSTEM
Wiper System
ENG MAIN
ECM/CAM, EMISS, INJ, ETC
FUEL PUMP
Fuel Pump System
DRL
Daytime Running Lamps
REAR DEFOG
Rear Defog System
HORN
Horn
FOG LP
Fog Lamps
5-101