Saturn L-Series - 2004 Fuse Box Diagram

Saturn L-Series - 2004 Fuse Box Diagram

These are some examples of symbols that may be found on the vehicle:
v
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
Turn and Lane-Change Signals
Headlamps
Headlamp High/Low-Beam Changer
Flash-to-Pass Feature
For additional information on the exterior lamps, see
Exterior Lamps on page 3-13
.
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, raise or lower the lever until
the arrow starts to flash. Hold it there until you complete
the lane change. The lever will return by itself when
you release it.
As you signal a turn or a lane change, if the arrows
flash rapidly, a signal bulb may be burned out and other
drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check the fuse, see
Fuses and Circuit
Breakers on page 5-92
and for burned-out bulbs.
3-6
Battery Run-Down Protection
Your vehicle is equipped with a battery saver feature
designed to protect your vehicle’s battery.
When any interior lamp is left on and the ignition is
turned off, the battery rundown protection system will
automatically turn the lamp off after 20 minutes.
Accessory Power Outlets
The accessory power outlets can be used to connect
electrical equipment such as a cellular phone or
CB radio.
The accessory power outlets are located in the front
and rear of the center console.
To use the outlet, remove the cover. When not in use,
always cover the outlet with the protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information
on the accessory power outlet.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-16
Ashtrays and Cigarette Lighter
Your vehicle may have an ashtray and cigarette lighter.
To use the lighter, just push it in all the way and let
go. When it’s ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
To remove the ashtray, lift it straight up. To reinstall it,
press the ashtray down firmly until it is fully seated.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
Climate Controls
Climate Control System
With this system you can control the heating, cooling
and ventilation for your vehicle.
3-17
Oil Pressure Light
If you have a low engine
oil pressure problem, this
light will stay on after
you start your engine, or
come on when you
are driving. This indicates
that your engine is not
receiving enough oil.
The engine could be low on oil, or could have some
other oil problem. Have it fixed immediately.
The oil light may also come on when the ignition is on
but the engine is not running, the light will come on as a
test to show you it is working, but the light will go out
when you turn the ignition to START. If it doesn’t come
on with the ignition on, you may have a problem with
the fuse or bulb. Have it fixed right away.
{
CAUTION:
Do not keep driving if the oil pressure is low. If
you do, your engine can become so hot that it
catches fire. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced.
Notice:
Lack of proper engine oil maintenance may
damage the engine. The repairs would not be
covered by your warranty. Always follow the
maintenance schedule in this manual for changing
engine oil.
3-37
Setting Preset Stations
Up to 18 stations (six FM1, six FM2, and six AM) can be
programmed on the six numbered pushbuttons, by
performing the following steps:
1. Turn the radio on.
2. Press AM FM to select FM1, FM2, or AM.
3. Tune in the desired station.
4. Press and hold one of the six numbered
pushbuttons until you hear a beep. Whenever that
numbered pushbutton is pressed, the station
that was set will return.
5. Repeat the steps for each pushbutton.
If the battery has been disconnected or a radio fuse has
been removed, the preset stations and time of day
will need to be reset.
Using Automatic Set
Use this feature to automatically save the radio preset
pushbuttons with the stations with the strongest
radio signals.
A.SET (Automatic Set):
Press this button to have the
radio automatically select the first 12 strongest radio
stations for FM and the six strongest radio stations
for AM.
To select the stations, perform the following:
1. Press AM FM to select FM1, FM2, or AM.
2. Press and hold AM FM until you hear a beep.
The radio will begin to search the current band.
The radio will store the stations, starting from the
lowest frequency, to each preset pushbutton. A.SET
will appear on the display when the radio is
finished storing the stations.
3-43
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations (six FM1,
six FM2, and six AM) by performing the following steps:
1. Turn the radio on.
2. Press AM FM to select FM1, FM2, or AM.
3. Tune in the desired station.
4. Press and hold one of the six numbered
pushbuttons until you hear a beep. Whenever you
press that numbered pushbutton, the station
you set will return.
5. Repeat the steps for each pushbutton.
If the battery has been disconnected or a radio fuse has
been removed, the preset stations and time of day
will need to be reset.
Using Automatic Set
Use this feature to automatically save the radio preset
pushbuttons with the stations with the strongest
radio signals.
A.SET (Automatic Set):
Press this button to have the
radio automatically select the first 12 strongest radio
stations for FM and the six strongest radio stations
for AM.
To select the stations, perform the following:
1. Press AM FM to select FM1, FM2, or AM.
2. Press and hold AM FM until you hear a beep.
The radio will begin to search the current band.
The radio will store the stations, starting from the
lowest frequency, to each preset pushbutton. A.SET
will appear on the display when the radio is
finished storing the stations.
Cancelling Automatic Set
The radio retains the previously stored stations so they
can be recalled when automatic set is canceled.
Press and hold A.SET until you hear a beep. A.SET will
no longer appear on the display.
3-46
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations (six FM1,
six FM2, and six AM) by performing the following steps:
1. Turn the radio on.
2. Press AM FM to select FM1, FM2, or AM.
3. Tune in the desired station.
4. Press the AUTO TONE arrow to select the
equalization.
5. Press and hold one of the six numbered
pushbuttons until you hear a beep. Whenever you
press that numbered pushbutton, the station
you set will return and the equalization that you
selected will be automatically stored for that
pushbutton.
6. Repeat the steps for each pushbutton.
If the battery has been disconnected or a radio fuse has
been removed, the preset stations and time of day
will need to be reset.
Using Automatic Set
Use this feature to automatically save the radio preset
pushbuttons with the stations with the strongest
radio signals.
A.SET (Automatic Set):
Press this button to have the
radio automatically select the first 12 strongest radio
stations for FM and the six strongest radio stations
for AM.
To select the stations, perform the following:
1. Press AM FM to select FM1, FM2, or AM.
2. Press and hold AM FM until you hear a beep.
The radio will begin to search the current band.
The radio will store the stations, starting from the
lowest frequency, to each preset pushbutton. A.SET
will appear on the display when the radio is
finished storing the stations.
Cancelling Automatic Set
The radio retains the previously stored stations so they
can be recalled when automatic set is canceled.
Press and hold A.SET until you hear a beep. A.SET will
no longer appear on the display.
3-51
Dinghy Towing
You may dinghy tow your vehicle from the front following
these steps:
1. Set the parking brake.
2. Turn the ignition key to ACC to unlock the steering
wheel.
3. Shift your transaxle to NEUTRAL (N).
4. Open the lid on the underhood fuse block and
remove the IGN 0/3/CR and IGN 1/2 fuses.
Refer to the underside of the underhood fuse block
cover for specific fuse locations.
5. Close the lid on the underhood fuse block and store
the two fuses in a safe place.
6. Close the hood.
7. Release the parking brake.
Once you have reached your destination replace the
IGN 0/3/CR and IGN 1/2 fuses.
Notice:
If you exceed 65 mph (110 km/h) while
towing your vehicle, it could be damaged. Never
exceed 65 mph (110 km/h) while towing your vehicle.
Notice:
Towing your vehicle from the rear could
damage it. Also, repairs would not be covered by the
warranty. Never have your vehicle towed from
the rear.
4-33
Power Windows and Other Power
Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by fuses. This greatly reduces the chance
of circuit overload and fire caused by electrical
problems.
There are three fuse blocks — the underhood fuse
block, the driver’s side floor console fuse block and the
passenger’s side floor console fuse block.
To identify and check fuses and relays, refer to the
Fuse Usage Chart on the inside surface of the
fuse panel door.
Floor Console Fuse Blocks
The driver’s side instrument panel is located by the
driver’s left leg.
Use a key or a coin to remove the fuse panel door and
access the fuses and relays.
5-92
Fuses
Usage
RADIO
Audio, OnStar
®
, Rear Seat DVD
(Option)
WIPER
Windshield Washers and Wipers
(Front)
IGN 3
Left Heated Seat Switch, Right
Heated Seat Switch, Air
Conditioning, Rear Defogger Relay
DEFOG LED
Rear Defog LED
BTSI/BCM/
MIRROR
Brake Transaxle Shift Interlock,
Body Control Module, Power Mirror
DIMMER
Dimmer Switch
RR COMP LP
Trunk Compartment Lamp
Relays
Usage
RR DEFOG
Rear Defogger
IGN 3
Ignition Switch
PARKLAMP
Park Lamps
HEADLAMP
Headlamps
5-93
The passenger’s side fuse block is located by the
passenger’s right leg.
Use a key or a coin to remove the fuse panel door and
access the fuses and relays.
Fuses
Usage
LOCKS
Power Door Locks
BODY
Power Door Locks, Heated Mirror
Relay, Liftgate Latch
POWER SEAT
Power Seat
FOG LAMP
Fog Lamps
PREM AMP/MCS
Premium Sound System
Amplifier
HEATED SEATS
Seat Heater
RR WIPER/
SUN ROOF
Rear Wiper/Washer (Wagon)
Relays
Usage
POWER
WINDOW
Power Windows, Power Sunroof
DRIVER DOOR
UNLOCK RELAY
Driver Door Unlock
DOOR UNLOCK
RELAY
Door Unlock
DOOR LOCK
RELAY
Door Lock
HEATED MIRROR Power Mirrors
FOG LAMP
Fog Lamps
5-94
Engine Compartment Fuse Block
The engine compartment
fuse block is located in the
forward part of the
engine compartment near
the battery.
Fuses
Usage
IGN 1/2
Ignition switch
IGN 0/3/CR
Ignition switch
COOL 1
Cooling fan module
COOL 2
Cooling fan module
ABS 1
Anti-Lock Brake System
ABS 2
Anti-Lock Brake System
Fuses
Usage
HVAC
BLOWER
High Blower
HORN
Horn
R HDLP
Right Headlamps
L HDLP
Left Headlamps
A/C
Air Conditioning System
LIGHTER
Cigarette Lighter
AUX POWER
Power Outlet
I/P BATT RT
Passenger’s Side Instrument Panel
Fuse Block
CONTROLS
B+
Powertrain Control Module (2.2L L4
(L61)), Engine Control Module (3.0L
V6 (L81), Transaxle Control Module
(3.0L V6 (L81))
BCM 2
Body Control Module
BCM/ECM/
CRUISE/ABS
Body Control Module, Engine
Control Module, Cruise Control,
ABS
EIS
Electronic Ignition System
(2.2L L4 (L61))
IGN
Ignition Coils (3.0L V6 (L81))
5-95
Fuses
Usage
INJ
Fuel Injectors (2.2L L4 (L61))
BACK-UP/TURN
Backup Lamps, Coolant Level
Switch
BRAKE
Brake Lamps
FUEL PUMP
Fuel Pump Relay
IGN 0
Park Neutral Position Switch,
Powertrain Control Module
CRUISE SW
Cruise Control Switch
CONTROLS
IGN 1
Cooling Fan Control Module,
Powertrain Control Module,
Transaxle (2.2L L4 (L61)),
Transaxle Control Module
(3.0L V6 (L81))
IGN 1
Instrument Cluster, Coolant Level
Switch, Air Bag, Electronic
PRND321
BCM/CLUSTER
Body Control Module, Instrument
Cluster, Dimmer Switch
Fuses
Usage
PARK LAMP
Front Park Lamps, Taillamps, Front
Marker Lamps, Rear Marker Lamps,
License Lamps, Radio Display
Lights, I/P Cluster Backlighting, I/P
Dimmer, Cigar Lighter Ring, Ashtray
Light, PRND321 Light, Climate
Control Switch Backlighting
HAZARD
Hazard Flasher, HBTT (Headlamp
HI Beam Indicator), I/P Cluster
REAR DEFOG
Rear Window Defogger
RADIO/ON-STAR
Audio System, OnStar
®
, Rear Seat
DVD (Option)
CD/DLC
Audio, Data Link Connector, (DLC),
Rear Seat DVD (Option)
ING 3
Cruise Clutch Switch, Emissions
Controls, Air Conditioner Relay,
Heated Oxygen Sensor
ENG CNTL 1
3.0L V6 (L81) Engine
ENG CNTL 2
3.0L V6 (L81) Engine
ENG CNTL 3
3.0L V6 (L81) Engine
A/C DIODE
Air Conditioner Diode
5-96