Pontiac Grand Prix - 2004 Fuse Box Diagram

Pontiac Grand Prix - 2004 Fuse Box Diagram

These are some examples of vehicle symbols you may find on your vehicle:
v
PASS-Key
®
III Operation
Your vehicle is equipped
with PASS-Key
®
III
(Personalized Automotive
Security System)
theft-deterrent system.
PASS-Key
®
III is a passive
theft-deterrent system. This
means you don’t have to do
anything special to arm or
disarm the system. It works
when you insert or remove
the key from the ignition.
When the PASS-Key
®
III system senses that someone
is using the wrong key, it shuts down the vehicle’s
starter and fuel systems. The starter will not work and
fuel will stop flowing to the engine. Anyone using a
trial-and-error method to start the vehicle will be
discouraged because of the high number of electrical
key codes.
When trying to start the vehicle, if the engine does not
start and the STARTING DISABLED DUE TO THEFT
SYSTEM warning message on the Driver’s Information
Center (DIC) comes on, the key may have a damaged
transponder. Turn the ignition off and try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time, you
may also want to check the fuse. See
Fuses and Circuit
Breakers on page 5-99
. If the engine still does not start
with the other key, your vehicle needs service. If your
vehicle does start, the first key may be faulty. See your
dealer who can service the PASS-Key
®
III to have a new
key made. In an emergency, contact Pontiac Roadside
Assistance. See
Roadside Assistance Program on
page 7-6
for more information.
It is possible for the PASS-Key
®
III decoder to “learn”
the transponder value of a new or replacement key.
Up to 10 additional keys may be programmed for
the vehicle. The following procedure is for programming
additional keys only. If all the currently programmed
keys are lost or do not operate, you must see your
dealer or a locksmith who can service PASS-Key
®
III
to have keys made and programmed to the system.
2-16
The main components of the instrument panel are the following:
A. Side Window Defogger Outlets. (See
Outlet
Adjustment on page 3-29
.)
B. Instrument Panel Outlets. (See
Outlet Adjustment
on page 3-29
.)
C. Exterior Lamps Control. (See
Exterior Lamps on
page 3-12
.)
D. TAP-Shift™ Control. (See
Automatic Transaxle
Operation on page 2-22
.)
E. Hazard Warning Flashers Button. (See
Hazard
Warning Flashers on page 3-4
.)
F. Instrument Panel Cluster. (See
Instrument Panel
Cluster on page 3-32
.)
G. Windshield Wiper Lever. (See
Windshield Washer
Lever on page 3-6
.)
H. Ignition. (See
Ignition Positions on page 2-18
.)
I. DIC (Driver Information Center). (See
Driver
Information Center (DIC) on page 3-45
.)
J. Audio System. (See
Audio System(s) on page 3-88
.)
K. Interior Lamps Brightness Control (Behind Steering
Wheel). (See
Interior Lamps on page 3-16
.)
L. Audio Controls. (See
Audio System(s) on page 3-88
.)
M. Hood Release. (See
Hood Release on page 5-11
.)
N. Tilt Steering Wheel Lever (on Steering Column).
(See
Tilt Wheel on page 3-5
.)
O. Cruise Control. (See
Cruise Control Lever on
page 3-8
.)
P. Climate Controls. (See
Climate Control System
on page 3-25
.)
Q. Storage Area.
R. Glove Box. (See
Glove Box on page 2-36
.)
S. Instrument Panel Fuse Block.
(See
Fuses and Circuit Breakers on page 5-99
.)
3-3
Flash-To-Pass Feature
This feature allows you to use the high-beam headlamps
to signal the driver in front of you that you want to pass.
Pull and hold the exterior lamps control lever toward
you to use this feature. When you do, the following
will occur:
If the headlamps are either off, in low-beam
or in Daytime Running Lamps (DRL) mode,
the high-beam headlamps will turn on. They’ll stay
on as long as you hold the lever there. Release
the lever to turn them off.
If the headlamps are in high-beam mode, they will
switch to low beam. To return to high-beam, push
the lever away from you.
If your vehicle is equipped with Head-Up Display (HUD),
an arrow will appear on the display to indicate that
the high beams are on.
Turn and Lane-Change Signals
To signal a turn, move the lever all the way up or down.
The lever returns automatically when the turn is
complete.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
If your vehicle is equipped with the Head-Up-Display
(HUD), the turn signals will appear in the HUD area
when making turns or lane changes. See
Head-Up
Display (HUD) on page 3-19
for more information.
Raise or lower the lever until the arrow starts to flash
to signal a lane change. Hold it there until the lane
change is complete. The lever returns to its original
position when it is released.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned-out signal bulb.
Other driver’s won’t see the signal.
Replace burned-out bulbs to help avoid possible
accidents. Check the fuse and for burned-out bulbs if
the arrow fails to work when signaling a turn. See
Fuses
and Circuit Breakers on page 5-99
for more information.
3-14
The HUD will “remember” the last display format
selected. When the vehicle is started if the last format
displayed was Format One or Format Three, then
Format One will be displayed.
If the last format was Format Two, then Format Two
will be displayed.
The HUD will automatically dim and brighten to
compensate for outside lighting.
The HUD display can temporarily light up depending on
the angle and position of the sunlight on the display.
This is normal and will change when the angle of
the sunlight on the HUD display changes.
Polarized sunglasses could also make the HUD image
harder to see.
Care of the HUD
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity
of the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry
it. Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If You Can’t See the HUD Image When
the Ignition Is On
Is anything covering the HUD unit?
Is the HUD dimmer setting bright enough?
Is the HUD image adjusted to the proper height?
Are you wearing polarized sunglasses?
Still no HUD image? Check the fuse in the
instrument panel fuse block. See
Fuses and Circuit
Breakers on page 5-99
.
If the HUD Image Is Not Clear
Is the HUD image too bright?
Are the windshield and HUD lens clean?
The windshield is part of the HUD system. If you ever
need a new windshield, be sure to get one designed for
HUD. If you don’t, the HUD image may look blurred
and out of focus.
3-22
Accessory Power Outlets
The vehicle has two 12-volt
outlets which can be used
to plug in electrical
equipment such as a
cellular telephone, a
compact disc player, etc.
One accessory power outlet is located on the center
console, below the front edge of the storage console.
The other is located inside the console.
Remove the tethered cap to use the outlet.
When not using the outlet, be sure to cover it with
the protective cap.
Notice:
When using an accessory power outlet,
maximum electrical load must not exceed amperage
rating. Always turn off any electrical equipment
when not in use. Leaving electrical equipment on
for extended periods will drain your battery.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem see your dealer for additional information
on accessory power outlets.
Notice:
Adding some electrical equipment to your
vehicle can damage it or keep other things from
working as they should. This wouldn’t be covered
by your warranty. Check with your dealer before
adding electrical equipment, and never use anything
that exceeds the amperage rating.
When adding electrical equipment, be sure to follow the
proper installation instructions included with the
electrical equipment you install.
Notice:
Power outlets are designed for accessory
plugs only. Do not hang any type of accessory
or accessory bracket from the plug. Improper use
of the power outlet can cause damage not covered
by your warranty.
3-23
A. Windshield Washer Fluid Reservoir. (See
Windshield
Washer Fluid on page 5-43
.)
B. Remote Positive (+) Battery Terminal. (See
Jump
Starting on page 5-49
.)
C. Battery. (See
Battery on page 5-48
).
D. Underhood Fuse Block. (See
Fuses and Circuit
Breakers on page 5-99
.)
E. Radiator Pressure Cap. (See
Cooling System on
page 5-32
).
F. Engine Coolant Recovery Tank. (See “Checking
Coolant” under
Cooling System on page 5-32
.)
G. Power Steering Fluid Reservoir (low in engine
compartment). (See
Power Steering Fluid on
page 5-42
.)
H. Electric Cooling Fan. (See
Cooling System on
page 5-32
.)
I. Engine Oil Dipstick. (See
Engine Oil on page 5-16
.)
J. Engine Oil Fill Cap. See
Engine Oil on page 5-16
.
K. Automatic Transaxle Fluid Dipstick. (See
Automatic
Transaxle Fluid on page 5-24
.)
L. Engine Coolant Bleed Valve. (See “How to Add
Coolant to the Radiator” under
Cooling System on
page 5-32
.)
M. Brake Master Cylinder. (See “Brake Fluid” under
Brakes on page 5-45
.)
N. Engine Air Cleaner/Filter. (See
Engine Air
Cleaner/Filter on page 5-22
.)
5-13
A. Windshield Washer Fluid Reservoir. (See
Windshield
Washer Fluid on page 5-43
.)
B. Remote Positive (+) Battery Terminal. (See
Jump
Starting on page 5-49
.)
C. Battery. (See
Battery on page 5-48
.)
D. Underhood Fuse Block. (See
Fuses and Circuit
Breakers on page 5-99
.)
E. Radiator Pressure Cap. (See
Cooling System on
page 5-32
.)
F. Engine Coolant Recovery Tank. (See “Checking
Coolant” under
Cooling System on page 5-32
.)
G. Power Steering Fluid Reservoir (low in engine
compartment). (See
Power Steering Fluid on
page 5-42
.)
H. Supercharger Oil Fill Location. (See
Supercharger
Oil on page 5-21
.)
I. Electric Cooling Fan. (See
Cooling System on
page 5-32
.)
J. Engine Oil Dipstick. (See
Engine Oil on page 5-16
.)
K. Engine Oil Fill Cap. (See
Engine Oil on page 5-16
.)
L. Engine Coolant Bleed Valve. (See “How to Add
Coolant to the Radiator” under
Cooling System on
page 5-32
.)
M. Automatic Transaxle Fluid Dipstick. (See
Automatic
Transaxle Fluid on page 5-24
.)
N. Brake Master Cylinder. (See “Brake Fluid” under
Brakes on page 5-45
.)
O. Engine Air Cleaner/Filter. (See
Engine Air
Cleaner/Filter on page 5-22
.)
5-15
Notice:
If you leave your radio on, it could be badly
damaged. The repairs wouldn’t be covered by
your warranty.
3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or in the accessory power outlet. Turn off
the radio and all lamps that aren’t needed. This will
avoid sparks and help save both batteries. And it
could save your radio!
4. Open the hoods and locate the batteries. Find the
positive (+) and negative (
-
) terminal locations on
each vehicle. You will not need to access your
battery for jump starting. Your vehicle has a remote
positive (+) jump starting terminal for that purpose
located under the underhood fuse block. The
underhood fuse block is located in the engine
compartment on the passenger’s side of the vehicle,
near the diagonal cross brace. See
Engine
Compartment Overview on page 5-12
for more
information on location.
To uncover the remote
positive (+) terminal,
depress the tab at the
bottom of the fuse block
and pull the cover off.
You should always use
the remote positive (+)
terminal instead of
the positive (+) terminal
on the battery.
5-50
Electrical System
Add-On Electrical Equipment
Notice:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle and
the damage wouldn’t be covered by your warranty.
Some add-on electrical equipment can keep other
components from working as they should.
Your vehicle has an air bag system. Before attempting
to add anything electrical to your vehicle see
Servicing
Your Air Bag-Equipped Vehicle on page 1-56
.
Headlamp Wiring
The headlamp circuit is protected by individual fuses in
the underhood fuse block. An electrical overload will
cause the fuse to blow. If this happens, have your
headlamp system checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools.
If the overload is caused by some electrical problem,
have it fixed.
Power Windows and Other Power
Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links in the wiring itself. This greatly
reduces the chance of fires caused by electrical
problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating. Spare fuses and a fuse puller are
located in the underhood fuse block. See
Underhood
Fuse Block
later in this section.
5-99
Instrument Panel Fuse Block
Some fuses are in a fuse
block located on the end
of the instrument panel
on the passenger side.
To get to the fuse block lift
up on the side panel.
A fuse usage chart is on the inside of this panel.
Circuit
Breakers
Usage
RAP
Retained Accessory Power
SUN ROOF
Sunroof
CRUISE SW
Cruise Switch
PK LP
Parking Lamps
5-100
Underhood Fuse Block
Some fuses are located in
a fuse block in the engine
compartment on the
passenger’s side. Unscrew
the bolt in the center of
the fuse block cover
and remove the cover.
A fuse chart is on the inside of the cover. To take the
cover off, press the tab at the bottom of the cover
and pull.
Fuses
Usage
1
Left Front Hiigh-Beam Headlamp
2
Right Front High-Beam Headlamp
3
Left Front Low-Beam Headlamp
4
Right Front Low-Beam Headlamp
5
Windshield Wipers/Washer
6
Washer/Remote Vehicle Current
7
Fog Lamps
9
SIR
10
Auxilliary Power
11
Horn
12
Emission
5-102
Fuses
Usage
13
A/C Clutch
14
Oxygen Sensor
15
Power Control Module
16
Power Control Module/Electronic
Throttle Control
17
Electronic Throttle Control
18
Display
19
Anti-Lock Brake Solenoid
20
Fuel Injection
21
Transmission Solenoid
22
Fuel Pump
23
Anti-Lock Brakes
24
Electronic Ignition
26
Battery Main 1
27
Battery Main 2
28
Battery Main 3
29
Fan 1
30
Battery Main 4
31
Anti-Lock Brake Motor
32
Fan 2
33
Starter
Relays
Usage
34
Hghi-Beam Headlamps
35
Low-Beam Headlamps
36
Fog Lamps
37
Iginition 1
38
Air Conditioner Compressor
39
Horn
40
Powertrain
41
Fuel Pump
42
Fan 1
43
Fan 3
44
Windshield Wiper/High
45
Windshield Wiper
46
Fan 2
48
Crank
49
Spare Fuse
50
Spare Fuse
51
Spare Fuse
52
Blank
53
Blank
54
Blank
55
Fuse Puller
§
A/C Clutch
5-103