Pontiac Aztek - 2004 Fuse Box Diagram

Pontiac Aztek - 2004 Fuse Box Diagram

These are some examples of vehicle symbols you may find on your vehicle:
v
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse. See
Fuses
and Circuit Breakers on page 5-113
. If the engine still
does not start with the other key, your vehicle needs
service. If your vehicle does start, the first key may be
faulty. See your dealer who can service the
PASS-Key
®
III to have a new key made.
It is possible for the PASS-Key
®
III decoder to learn the
transponder value of a new or replacement key. Up to
10 total keys may be programmed for the vehicle. This
procedure is for learning additional keys only. If all the
currently programmed keys are lost or do not operate,
you must see your dealer or a locksmith who can service
PASS-Key
®
III to have keys made and programmed to
the system.
See your dealer who can service PASS-Key
®
III to get a
new key blank that is a cut exactly as the ignition key
that operates the system.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS-Key
®
III to
have new keys made. To program additional keys you
will need two current driver’s keys (black in color).
You must add a step to the following procedure. After
Step 3, repeat Steps 1 through 3 with the second current
driver’s key. Then continue with Step 4.
To program the new PK3
®
key do the following:
1. Verify the new key has PK3
®
stamped on it.
2. Insert the current driver’s key in the ignition and
start the engine. If the engine will not start, see
your dealer for service.
3. After the engine has started, turn the key to OFF,
and remove the key.
4. Insert the key to be programmed and turn it to ON
within 10 seconds of removing the previous key.
5. The SECURITY message will turn off once the key
has been programmed. It may not be apparent that
the SECURITY message went on due to how
quickly the key is programmed.
6. Repeat Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the SECURITY message
comes on and stays on, you will be able to restart your
engine if you turn it off. Your PASS-Key
®
III system,
however, is not working properly and must be serviced
by your dealer. Your vehicle is not protected by the
PASS-Key
®
III system at this time.
If you lose or damage a PASS-Key
®
III key, see your
dealer who can service PASS-Key
®
III to have a
new key made.
2-17
The main components of the instrument panel are the
following:
A. Side Outlets. See
Outlet Adjustment on page 3-30
.
B. Instrument Panel Cluster. See
Instrument Panel
Cluster on page 3-32
.
C. Hazard Warning Flasher Switch. See
Hazard
Warning Flashers on page 3-6
.
D. Head-Up Display Switch and Driver Information
Center (DIC) Controls or DIC Controls. See
Head-Up
Display (HUD) on page 3-20
and
DIC Controls
and Displays on page 3-55
.
E. Center Outlets. See
Outlet Adjustment on page 3-30
.
F. Audio System. See
Audio System(s) on page 3-64
.
G. Side Outlets. See
Outlet Adjustment on page 3-30
.
H. Turn Signal/Multifunction Lever. See
Turn
Signal/Multifunction Lever on page 3-8
.
I. Exterior/Interior Lamp Switch. See
Exterior Lamps
on page 3-13
and
Interior Lamps on page 3-15
.
J. Audio Steering Wheel Controls. See
Audio Steering
Wheel Controls on page 3-117
.
K. Hood Release. See
Hood Release on page 5-11
.
L. Parking Brake. See
Parking Brake on page 2-25
.
M. Horn. See
Horn on page 3-7
.
N. Ignition Switch. See
Ignition Positions on page 2-18
.
O. Audio Steering Wheel Controls. See
Audio Steering
Wheel Controls on page 3-117
.
P. Shift Lever. See
Automatic Transaxle Operation on
page 2-22
.
Q. Accessory Power Outlet. See
Accessory Power
Outlets on page 3-22
.
R. Rear Outlets. See
Outlet Adjustment on page 3-30
.
S. Console/Cooler. See
Console/Cooler on page 2-36
.
T. Floor Console Fuse Block. See
Fuses and Circuit
Breakers on page 5-113
.
U. Cupholders and Ashtray. See
Cupholder(s) on
page 2-34
and
Ashtrays and Cigarette Lighter on
page 3-23
.
V. Instrument Panel Switchbank. See
Instrument Panel
Switchbank on page 3-19
.
W. Cigarette Lighter. See
Ashtrays and Cigarette
Lighter on page 3-23
.
X. Climate Controls. See
Climate Control System on
page 3-24
or
Dual Climate Control System on
page 3-27
.
Y. Glove Box. See
Glove Box on page 2-34
.
3-5
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity
of the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry
it. Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you cannot see the HUD image,
check to see if one of the following has occurred:
Something is covering the HUD unit.
The HUD dimmer knob is adjusted properly
The HUD image is adjusted to the proper height.
Ambient light in the direction your vehicle is facing,
is low.
A fuse is blown. See
Fuses and Circuit Breakers on
page 5-113
.
If you ever have to have your windshield replaced, be
sure to get one that is designed for the HUD or your
HUD image may look blurred and out of focus.
Accessory Power Outlets
With accessory power outlets you can plug in electrical
equipment such as a cellular telephone or CB radio.
There is a single front power outlet located on the floor
console above the climate control system outlets.
There is one rear power outlet located in the rear of the
vehicle on the driver’s side.
To use the outlet, pull the cover down. When not using
it, cover the outlet with the protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain electrical accessories may not be compatible to
the accessory power outlet and could result in blown
vehicle or adapter fuses.
3-22
If you experience a problem, see your dealer for
additional information on accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
proper installation instructions included with the
equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
Ashtrays and Cigarette Lighter
If your vehicle has an ashtray and cigarette lighter they
are located in the glove box.
The ashtray fits into the cupholders. The cigarette
lighter installs into the accessory power outlet in the
instrument panel switchbank.
To use the lighter, push it in all the way and let go.
When it’s ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter in while it is
heating will not allow the lighter to back away from
the heating element when it is hot. Damage from
overheating may occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
Notice:
If you put papers or other flammable items
in the ashtray, hot cigarettes or other smoking
materials could ignite them and possibly damage
your vehicle. Never put flammable items in the
ashtray.
3-23
A. Underhood Fuse Block. See
Fuses and Circuit
Breakers on page 5-113
.
B. Remote Positive (+) Terminal. See
Jump Starting on
page 5-42
.
C. Power Steering Fluid Reservoir. See
Power Steering
Fluid on page 5-35
.
D. Automatic Transaxle Fluid Dipstick. See
Automatic
Transaxle Fluid on page 5-20
.
E. Brake Master Cylinder. See
Brakes on page 5-38
.
F. Windshield Washer Fluid Reservoir. See
Windshield
Washer Fluid on page 5-36
.
G. Battery. See
Battery on page 5-41
.
H. Radiator Pressure Cap. See
Radiator Pressure Cap
on page 5-25
.
I. Engine Oil Fill Cap. See
Engine Oil on page 5-13
.
J. Engine Oil Dipstick. See
Engine Oil on page 5-13
.
K. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 5-18
.
L. Coolant Recovery Tank. See
Engine Coolant on
page 5-22
.
Engine Oil
Checking Engine Oil
It is a good idea to check your engine oil every time you
get fuel. In order to get an accurate reading, the oil
must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop. See
Engine Compartment Overview on page 5-12
for
the location of the engine oil dipstick.
Turn off the engine and give the oil several minutes to
drain back into the oil pan. If you don’t, the oil
dipstick might not show the actual level.
Pull out the dipstick and clean it with a paper towel or
cloth, then push it back in all the way. Remove it again,
keeping the tip down, and check the level.
5-13
Notice:
If you leave your radio or other accessories
on during the jump starting procedure, they could
be damaged. The repairs would not be covered
by your warranty. Always turn off your radio and
other accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette
lighter or in the accessory power outlet(s). Turn
off the radios and all lamps that aren’t needed. This
will avoid sparks and help save both batteries.
And it could save your radio!
4. Open the hoods and locate the batteries. Find the
positive (+) and negative (
) terminals on each
vehicle.
You will not need to access your battery for jump
starting. Your vehicle has a remote positive (+) jump
starting terminal for that purpose. The terminal is
located under a tethered cap at the front of the
underhood fuse and relay center. See
Engine
Compartment Overview on page 5-12
for more
information on location.
Flip the cap up to access the remote positive (+)
terminal. You should always use the remote
positive (+) terminal instead of the positive (+)
terminal on the battery.
{
CAUTION:
An electric fan can start up even when the
engine is not running and can injure you. Keep
hands, clothing and tools away from any
underhood electric fan.
5-43
If the accessory inflator system does not turn on or the
light does not come on, the fuse may be blown or
installed incorrectly. See
Fuses and Circuit Breakers on
page 5-113
or see your dealer for service.
Your accessory inflator will automatically shut off after
about 10 minutes. The light in the switch will blink. After
about one minute you can use the system again. Press
the inflator switch and the indicator light will come on.
Notice:
If you run the accessory inflator longer than
30 minutes at a time, you could damage the
inflator. The repairs would not be covered by your
warranty. Run the inflator for short periods of
time only.
After running the accessory inflator for 30 minutes, wait
at least 10 minutes before restarting the accessory
inflator.
To turn off the inflator, do the following:
1. Press the switch and detach the hose, first from the
inflated object, then from the outlet.
2. Put the protective cap back on.
3. Place the inflator kit tools in the pouch, and store in
the glove box.
To put the cover back on, line up the tabs at the back of
the cover and put it in place. Push down the tab to
secure the cover.
If a Tire Goes Flat
It’s unusual for a tire to “blowout” while you’re driving,
especially if you maintain your tires properly. If air goes
out of a tire, it’s much more likely to leak out slowly.
But if you should ever have a “blowout,” here are a few
tips about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and grip the steering wheel firmly.
Steer to maintain lane position, and then gently brake to
a stop well out of the traffic lane.
5-77
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links.
Look at the silver-colored L-Band inside the fuse. If the
L-Band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating.
If you ever have a problem on the road and don’t have
a spare fuse, you can borrow one that has the same
amperage. Just pick a feature of your vehicle that
you can get along without – like the radio or cigarette
lighter – and use its fuse, if it is the right amperage.
Replace it as soon as you can.
There are two fuse blocks in your vehicle: the floor
console fuse block and the underhood fuse block.
Floor Console Fuse Block
The floor console fuse
block is located to the right
of the shift lever.
The fuses marked spare are available if a replacement
fuse is needed.
Pull the door open to access the fuse block.
5-113
Fuse
Usage
1
Empty
2
Steering Wheel Radio Controls
3
Power Door Locks
4
Empty
5
Empty
6
Empty
7
Empty
8
Empty
9
Empty
10
Turn Signal and Hazard Lamp
Flashers
Fuse
Usage
11
Power Seats
12
Electronic Level Control (ELC)
Compressor
13
Liftgate and Endgate
14
Rear Auxiliary Power Outlet
15
Electronic Level Control (ELC)
Compressor Relay and Height
Sensor
16
Heated Mirrors
17
Power Mirrors
18
Ignition 1 Module
19
Turn Signal Switch
21
Rear Defogger
22
Air Bag Module
24
TCC Switch
25
Climate Control Blower Motor
26
Climate Control Mode and
Temperature Motors and Head-Up
Display
28
Empty
29
Windshield Wipers and Washer
30
Instrument Panel Cluster, Body
Control Module (BCM),
PASS-Key
®
III
31
Park Lock Ignition Key Solenoid
5-114
Fuse
Usage
32
Empty
34
Power Sunroof
35
Power Windows
36
Map Lamps, Courtesy Lamps and
Instrument Panel Lights
37
Radio
38
UQ3 Radio Amplifier
39
Head-Up Display
40
Hazard Flashers
41
Instrument Panel Cluster, Climate
Control, Security LED and Remote
Keyless Entry Module
42
PASS-Key
®
III
43
Accessory Diode
44
Body Control Module (BCM)
Relay
Usage
20
Rear Defogger Relay
23
Ignition Relay
27
Accessory Relay
33
Retained Accessory Power Relay
Underhood Fuse Block
This fuse block is located in the engine compartment on
the passenger’s side of the vehicle. See
Engine
Compartment Overview on page 5-12
for more
information on location.
The back-up lamp relay (A) is located to the left of the
underhood fuse block.
To remove the cover, press the two tabs in and lift up
the cover.
5-115
Fuse
Usage
1
Fuel Pump
2
Air Conditioning Compressor Clutch
3
Horn
4
Engine Controls – Emissions and
Sensors
5
Power Control Module
(PCM) – Battery Power
6
Anti-Lock Brake System (ABS)
Control Module
7
Transaxle Solenoids
Fuse
Usage
9
Anti-lock Brake System (ABS)
Solenoid Valves
10
Oxygen Sensors – Emissions
Control
11
Injectors
13
Engine Controls
14
Daytime Running Lamps (DRL)
15
Passenger’s Low-Beam Headlamp
17
Driver’s Low-Beam Headlamp
18
Driver’s High-Beam Headlamp
19
Ignition Switch Battery Power
20
Parking Lamps – Front and Rear
23
Passenger’s High-Beam Headlamp
24
Vent Solenoid
25
DVD
26
Front Fog Lamps
27
Ignition Relay, Neutral Start Switch,
Powertrain Control Module (PCM)
28
Body Control Module
(BCM) – Battery Power
29
S-Band
30
All-Wheel Drive (AWD) Module
31
Cruise Control
5-116
Fuse
Usage
32
Front Power Outlets/Lights, OnStar
®
33
Automatic Transaxle Shift Lock
Control System
35
Starter Solenoid Battery Fuse
36
Anti-lock Brake System (ABS) Motor
39
Engine Cooling Fan
40
Engine Cooling Fan
41
Main Battery Fuse for Retained
Accessory Power Relay and
Accessory Relay
42
Main Battery Fuse for Heated
Seats, Air
45
Main Battery Fuse for Power
Outlets, Level Control, Power Seats
and Mirrors and Body computer
47
Main Battery Fuse for Climate
Control Blower and Ignition 3 Relay
48
Main Battery Fuse for Ignition
Switch, Radio, Heads-Up Display,
Remote Keyless Entry (RKE),
Instrument Cluster, Air Conditioning
and Body Computer
70
§
Diode for Air Conditioning
Compressor Clutch
Relay
Usage
A
Back-Up Lamps
50
Horn
51
Fuel Pump
52
Air Conditioning Clutch
53
Daytime Running Lamps (DRL)
54
Low-Beam Headlamps
55
Parking Lamps
56
High-Beam Headlamps
57
Fog Lamps
58
Starter Relay
59
Cooling Fan
60
Ignition 1 Relay
61
Cooling Fan
62
Cooling Fan
5-117