Oldsmobile Silhouette - 2004 Fuse Box Diagram

Oldsmobile Silhouette - 2004 Fuse Box Diagram

These are some examples of symbols you may find on your vehicle:
v
Resetting the Power Sliding Door
The power sliding door may operate incorrectly or not
at all because of the following conditions:
A low voltage or dead battery
A disconnected battery
If the instrument panel PWR/HEATED SEAT PSD
fuse or the underhood fuse 8, 27, or 29 are
removed or blown.
See
Fuses and Circuit Breakers on page 5-101
for more
information about your fuse panel.
If any of these conditions occur, the power sliding door
will need to be reset. If your vehicle has the dual
power sliding doors, both doors will have to be reset.
To reset a door, do the following:
1. Check to be sure the power sliding door is unlocked
and securely closed.
2. Turn the ignition key to OFF.
3. If the power sliding door override is on, press the
textured end of the power sliding door override
switch to turn it off.
4. Remove fuse 29 from the underhood fuse block.
Leave it out for 30 seconds.
5. Reinstall the fuse and wait 10 seconds.
6. Turn the power sliding door override on by pressing
the end of the switch with the override symbol on it.
7. Press the power sliding door switch(es) to open the
power sliding door.
8. Open the door all of the way.
9. Wait five seconds and close the door by pressing
the power sliding door switch(es).
10. Wait five seconds and repeat Steps 7 through 9.
If the door does not rest in the fully open position after
repeating Step 7, repeat Steps 7 through 9 again. If
the door still does not operate correctly, see your dealer
for service.
Liftgate
To unlock or lock the liftgate from the outside, use the
remote keyless entry transmitter. For more information,
see
Remote Keyless Entry System Operation on
page 2-5
.
Open the liftgate using the handle located above the
license plate. Once slightly opened, the liftgate will rise
by itself. Lamps in the rear of the vehicle will come
on, illuminating the rear cargo area. See
Interior Lamps
on page 3-18
.
2-21
Entering Programming Mode
To program features, your vehicle must be in the
programming mode. Follow these steps:
1. The content theft-deterrent system must be
disarmed. See
Content Theft-Deterrent on
page 2-26
.
2. Remove the BCM PRGRM fuse from the instrument
panel fuse block, located to the right of the glove
box. See
Fuses and Circuit Breakers on page 5-101
.
3. Close the driver’s door.
4. Turn the ignition key to ACCESSORY.
5. Count the number of chimes you hear. You will
hear two to four chimes depending on the features
your vehicle is equipped with. Refer to the chart
shown previously.
You can now program your choices.
To exit the programming mode, follow the steps listed
under
Exiting Programming Mode on page 2-69
.
Delayed Illumination and Exit
Lighting
This feature allows you to customize the interior lamps
when entering and exiting the vehicle.
Programmable Modes
Mode 1:
Both Features Off. The interior lamps will turn
on or off at the same instant that a door is opened or
closed.
Mode 2:
Delayed Illumination Only. The interior lamps
will stay on for about 25 seconds after all the doors
and liftgate are closed, or until you lock the doors.
Mode 3:
Exit Lighting Only. The interior lamps will come
on whenever you remove the key from the ignition
and stay on for about 25 seconds, or until you lock the
doors.
Mode 4:
Both Features On. This combines
Modes 2 and 3.
2-61
3. Press the button with the horn symbol on the
remote keyless entry transmitter.
4. Count the number of chimes you hear. The number
of chimes indicates the vehicle’s current
programmed mode. If you do not wish to change the
current mode, you can either exit the programming
mode by following the instructions later in this section
or program the next feature available on your vehicle.
5. Press the panic button to change the current mode.
6. Press the panic button until you hear the number
of chimes corresponding to the mode selection
you want.
7. Remove your key from the door key cylinder.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
next in this section or program the next feature available
on your vehicle.
Exiting Programming Mode
To exit programming mode, turn the key from
ACCESSORY to OFF and put the BCM PRGRM fuse
back into the instrument panel fuse block.
After programming a feature, you can exit the
programming mode at anytime. Also, if your vehicle is
equipped with the content theft-deterrent system,
remember to arm the system before exiting.
2-69
A. Side Outlets. See
Outlet Adjustment on page 3-34
.
B. Front Outlets. See
Outlet Adjustment on page 3-34
.
C. Turn Signal/Multifunction Lever. See
Turn
Signal/Multifunction Lever on page 3-8
.
D. Hazard Warning Flasher Switch. See
Hazard
Warning Flashers on page 3-6
.
E. Instrument Panel Cluster. See
Instrument Panel
Cluster on page 3-42
.
F. Center Outlets. See
Outlet Adjustment on page 3-34
.
G. Audio System. See
Audio System(s) on page 3-63
.
H. Side Outlets. See
Outlet Adjustment on page 3-34
.
I. Exterior Lamps Control. See
Exterior Lamps
on page 3-16
.
J. Hood Release. See
Hood Release on page 5-10
.
K. Audio Steering Wheel Controls. See
Audio Steering
Wheel Controls on page 3-97
.
L. Horn. See
Horn on page 3-7
.
M. Ignition Switch. See
Ignition Positions on page 2-31
.
N. Audio Steering Wheel Controls. See
Audio Steering
Wheel Controls on page 3-97
.
O. Climate Controls. See
Climate Control System
on page 3-28
or
Dual Climate Control System
on page 3-31
.
P. Rear Fan Controls. See
Rear Climate Control
System (Without Entertainment System) on
page 3-34
or
Rear Climate Control System
(With Entertainment System) on page 3-36
.
Q. Cupholder Tray. See
Cupholder(s) on page 2-52
.
R. Accessory Power Outlet. See
Accessory Power
Outlets on page 3-27
.
S. Instrument Panel Switchbank. See
Instrument Panel
Switchbank on page 3-23
.
T. Glove Box. See
Glove Box on page 2-51
.
U. Front Outlets. See
Outlet Adjustment on page 3-34
.
V. Instrument Panel Fuse Block. See
Fuses and
Circuit Breakers on page 5-101
.
3-5
Accessory Power Outlets
With accessory power outlets you can plug in electrical
equipment such as a cellular telephone or CB radio.
The front accessory power outlet is located below
the cupholder drawer.
Pull the cover down to use the accessory power outlet.
When not in use, keep the cover on.
The rear accessory power outlet is located in the rear
compartment on the driver’s side next to the air
inflator system.
To remove the cover, pull the tab on the cover and pull
it off. To put the cover back on, line up the tabs at
the back of the cover and put the cover in place. Push
down the tab to secure the cover. When not in use,
always cover the rear accessory power outlet with the
protective cap.
Notice:
Leaving electrical equipment on for
extended periods will drain the battery. Always turn
off electrical equipment when not in use and do
not plug in equipment that exceeds the maximum
amperage rating.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience a
problem see your dealer for additional information
on accessory power outlets.
Notice:
Adding any electrical equipment to your
vehicle may damage it or keep other components
from working as they should. The repairs would not
be covered by your warranty. Check with your
dealer before adding electrical equipment.
When adding electrical equipment, be sure to follow the
proper installation instructions included with the
equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by your warranty. Do not
hang any type of accessory or accessory bracket
from the plug because the power outlets are
designed for accessory power plugs only.
3-27
A. Underhood Fuse Block.
See
Fuses and Circuit Breakers on page 5-101
.
B. Remote Positive (+) Terminal.
See
Jump Starting on page 5-42
.
C. Windshield Washer Fluid Reservoir.
See
Windshield Washer Fluid on page 5-37
.
D. Radiator Pressure Cap.
See
Radiator Pressure Cap on page 5-25
.
E. Power Steering Fluid Reservoir.
See
Power Steering Fluid on page 5-36
.
F. Engine Oil Fill Cap.
See
Engine Oil on page 5-13
.
G. Engine Oil Dipstick.
See
Engine Oil on page 5-13
.
H. Transaxle Fluid Dipstick.
See
Automatic Transaxle Fluid on page 5-19
.
I. Brake Master Cylinder Reservoir.
See
Brakes on page 5-38
.
J. Engine Air Cleaner/Filter.
See
Engine Air Cleaner/Filter on page 5-18
.
K. Coolant Recovery Tank.
See
Cooling System on page 5-28
.
Engine Oil
Checking Engine Oil
It is a good idea to check your engine oil every time you
get fuel. In order to get an accurate reading, the oil
must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop. See
Engine Compartment Overview on page 5-12
for
the location of the engine oil dipstick.
Turn off the engine and give the oil several minutes to
drain back into the oil pan. If you don’t, the oil
dipstick might not show the actual level.
Pull out the dipstick and clean it with a paper towel or
cloth, then push it back in all the way. Remove it again,
keeping the tip down, and check the level.
5-13
The terminal is located
under a tethered cap at
the front of the underhood
fuse block. See
Engine
Compartment Overview on
page 5-12
for more
information on location.
Squeeze the tabs and pull up on the cap to access
the remote positive (+) terminal. You should
always use the remote positive (+) terminal instead
of the positive (+) terminal on your battery.
{
CAUTION:
An electric fan can start up even when the
engine is not running and can injure you.
Keep hands, clothing and tools away from
any underhood electric fan.
{
CAUTION:
Using a match near a battery can cause battery
gas to explode. People have been hurt doing
this, and some have been blinded. Use a
flashlight if you need more light.
Be sure the battery has enough water. You do
not need to add water to the ACDelco
®
battery
installed in your new vehicle. But if a battery
has filler caps, be sure the right amount of
fluid is there. If it is low, add water to take care
of that first. If you do not, explosive gas could
be present.
Battery fluid contains acid that can burn you.
Do not get it on you. If you accidentally get it
in your eyes or on your skin, flush the place
with water and get medical help immediately.
5-44
{
CAUTION:
Inflating something too much can make it
explode, and you or others could be injured.
Be sure to read the inflator instructions, and
inflate any object only to its recommended
pressure.
To use your accessory inflator system, do the following:
1. Turn the ignition to ACCESSORY or RUN.
2. Attach the appropriate nozzle adapter, if required,
to the end of the hose that has the pressure gage.
3. Attach that end of the hose to the object you wish
to inflate.
4. Remove the protective cap covering the outlet.
5. Attach the other end of the hose to the outlet.
6. Press the accessory inflator switch. The light in the
switch will come on to show the system is working.
If the accessory inflator system does not turn on or
the light does not come on, the fuse may be blown or
installed incorrectly. See
Fuses and Circuit Breakers
on page 5-101
or see your dealer for service.
Your accessory inflator will automatically shut off after
about 10 minutes. The light in the switch will blink.
After about one minute you can use the system again.
Press the switch and the indicator light will come on.
Notice:
If you run the accessory inflator longer
than 30 minutes at a time, you could damage
the inflator. The repairs would not be covered by
your warranty. Run the inflator for short periods of
time only.
After running the accessory inflator for 30 minutes, wait
at least 10 minutes before restarting the accessory
inflator.
To turn off the inflator, do the following:
1. Press the switch and detach the hose, first from
the inflated object, then from the outlet.
2. Put the protective cap back on.
3. Place the inflator kit tools in the pouch, and store
in the glove box.
To put the cap back on, line up the tabs at the back
of the cover and put it in place. Push down the tab to
secure the cap.
5-75
Headlamp Wiring
The headlamp wiring is protected by an internal circuit
breaker in the instrument panel fuse panel. An electrical
overload will cause the lamps to go on and off, or in
some cases to remain off. If this happens, have
your headlamp wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an internal
circuit breaker and a fuse. If the motor overheats due
to heavy snow, etc., the wiper will stop until the
motor cools. If the overload is caused by some electrical
problem, be sure to get it fixed.
Power Windows and Other Power
Options
Circuit breakers in the instrument panel fuse panel
protect the power windows and other power accessories.
When the current load is too heavy, the circuit breaker
opens and closes, protecting the circuit until the
problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers,
and fusible thermal links.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
If you ever have a problem on the road and do not have
a spare fuse, you can borrow one that has the same
amperage or use one of the spare fuses in the
underhood fuse block. Just pick some feature of your
vehicle that you can get along without — like the radio or
cigarette lighter — and use its fuse, if it is the right
amperage. Replace it as soon as you can.
There are two fuse blocks in your vehicle, the instrument
panel fuse block and the underhood fuse block.
5-101
Instrument Panel Fuse Block
The instrument panel
fuse block is located to
the right of the glove
box on the end of the
instrument panel.
Pull the door open to access the instrument panel
fuse block.
Fuse
Usage
SWC
BACKLIGHT
Steering Wheel Radio Control
Switches (Illumination)
PCM/PASS
KEY/CLUSTER
Instrument Cluster to PRNDL
Indicators
PWR MIRROR
Power Remote Control Mirror Switch
CRUISE
Cruise Control Module, Switch
and Release Switch
Blank
Not Used
PCM/CRANK
Powertrain Control Module (PCM),
Ignition Crank
5-102
Fuse
Usage
PASS KEY
PASS-Key
®
III System
PWR LOCK
Power Door Locks
HTD MIRROR
Heated Mirrors
RH T/LP
Not Used
RR FOG LP
Not Used
CIGAR/DIC/
APO FRT
Cigarette Lighter, DIC, Front
Auxiliary Power Outlets, Data Link
T/SIG
Turn Signal Switch
PWR QTR
VENT
Interior Lamp and Multifunction
Switch (Power Vent Switch),
Auto Level
FRT/WPR/
WSHR
Windshield Wiper/Washer Motor
and Switch
HAZARD
Hazard Switch
RR PWR SCKT
Rear Electric Accessory Plug
Housing
DRL
Daytime Running Lamp Control
Module
LH T/LP
Not Used
Fuse
Usage
RR DEFOG/
HTD MIRROR
Rear Window Defogger Relay,
Heated Mirrors
ON STAR
OnStar
®
SIR
Inflatable Restraint Control Module
HVAC
BLOWER
Heater-A/C Control
MALL
CLUSTER
Instrument Cluster, Body Control
Module, Electronic Level Control
(ELC) Sensor and Relay, Theft,
Door Ajar
STOP LAMP
Stoplamp Switch
CLUSTER
BATT
Module/Electronic Brake Control
Module/Electronic Brake Traction
Control Module (EBCM/EBTCM)
ENHANCED
EVAP/AWD
Evaporative Emissions (EVAP)
Canister Vent Solenoid Valve,
All-Wheel Drive (AWD)
Blank
Not Used
ELC/TRAILER
ELC Air Compressor and ELC
Height Sensor, Trailer Harness
CTSY LAMP
Courtesy Lamp
5-103
Fuse
Usage
IGN 1
BCM, Electronic Brake Control
Indicator Lamp Driver Module,
Instrument Panel Cluster, Rear Side
Door Actuator Control Module,
Rear Windows, Rear Parking Aid
RR HVAC
TEMP CONT
Rear HVAC-A/C Control
RR WPR/
WSHR
Rear Window Wiper Motor,
Rear Window Wiper/Washer and
Multifunction Switch (Rear Window
Wiper/Washer Switch)
LH HEADLP
LOW
Not Used
LH HEADLP
HIGH
Not Used
Blank
Not Used
Blank
Not Used
Blank
Not Used
RAP RELAY
Retained Accessory Power (RAP)
Relay
Blank
Not Used
Fuse
Usage
HVAC/DIC/DRL/
HEATED SEAT
Air Inlet Actuator, DIC Display, DRL
Control Module, Heater-A/C Control,
Temperature Door Actuator (Front)
and Rear Window Defogger Relay
BCM PRGRAM
BCM Programming
RH HEAD
LP LOW
Not Used
RH HEAD
LP HIGH
Not Used
PCM/ABS
IGN MAIN Relay and PCM,
Electronic Brake Control Module
Circuit Breaker
Usage
HEADLAMP
Daytime Running Lamps (DRL)
Control Module, Headlamp and
Instrument Panel Dimmer Switch
PWR SLD DR
Power Sliding Door
PWR WDO
Front Power Windows
PWR/HEATED
SEAT PSD
Six-Way Power Seats and Rear
Side Door Actuator Motor
FRT HVAC
HI BLWR
Blower Motor Hi Speed Relay
Module
5-104
Underhood Fuse Block
This fuse block is located
in the engine compartment,
in front of the windshield
washer fluid reservoir.
See
Engine Compartment
Overview on page 5-12
for more information
on location.
The fuses marked spare are available if a replacement
fuse is needed.
To remove the cover, turn the knob counterclockwise
and lift up.
When finished, to put the cover back on, turn the knob
clockwise to tighten it. Make sure that the remote
positive (+) terminal cover is on correctly.
Fuse
Usage
1
Coolant Fans
2
Not Used
3
Circuit Breakers: Front Comfort
Controls Hi Blower, and Headlamp
Fuses (Instrument Panel): Hazard
and Stoplamp, PASS-Key
®
4
Circuit Breaker: Power Seat and
Power Sliding Door. Fuses
(Instrument Panel): Electronic Level
Control and Rear Defogger, Trailer,
Fog Lamps
5-105
Fuse
Usage
5
Ignition Switch to Fuses (Instrument
Panel): ABS/TCS Ignition, Cruise,
DRL, Electronic PRNDL, Ignition 1,
AWD, PSD, Air Bag, Turn Signal
and Powertrain Control Module
[IGN MAIN Relay (Underhood Fuse
Block: A/C Clutch, Electronic
Ignition, Ignition 1-U/H, INJ, TCC)]
6
Coolant Fans
7
Fuses (Instrument Panel): ABS
Module Battery, Cigarette Lighter,
Courtesy Lamps, Front Power
Socket, Power Locks, Power Mirrors
and Right Rear Power Socket,
OnStar, RAP
8
Ignition Switch to Fuses (I/P): Body
Control Module Program, Front
Comfort Controls Low/Medium
Blower, Front Wiper/Washer,
HVAC/DRL, MALL/Radio/DIC,
Power Quarter Vent, Rear HVAC,
Rear Wiper/Washer. SWC
Accessory and Power Window
Circuit Breaker, RAP
18
Fuel Injectors 1–6
19
Not Used
Fuse
Usage
20
Not Used
21
Evaporative Emissions (EVAP)
Canister Purge Valve, Heated
Oxygen Sensors 1 and 2, Mass Air
Flow (MAF) Sensor
22
Not Used
23
Not Used
24
Not Used
25
Ignition Control Module (ICM)
26
Not Used
27
Transaxle Range Switch to
Back-up Lamps
28
A/C Clutch Relay to A/C
Compressor Clutch Oil
29
Driver Information Display, Heater
A/C Control, Radio, Rear (LH and
RH) Side Door Actuator Control
Motor, Remote Control Door Lock
Receiver (RCDLR), Security
Indicator Lamp and Theft-Deterrent
Shock Sensor
30
Generator
5-106
Fuse
Usage
31
Automatic Transaxle (Torque
Converter Clutch Solenoids)
Stoplamp Switch to Powertrain
Control Module
32
Fuel Pump Relay
33
Powertrain Control Module
34
Not Used
35
Fog Lamp Relay
36
Horn Relay
37
Daytime Running Lamps (DRL)
Control Module, Headlamps and
Instrument Panel Dimmer Switch
Theft-Deterrent Relay to Headlamps
38
Not Used
39
AIR
40
Mini Fuse Puller
§
Air Conditioning Clutch Diode
Relay
Usage
9
Right Fan 1, Left Fan 2
10
Left Fan 2
11
Fuses: A/C Clutch, Ignition 1-U/H,
Electronic Ignition, TCC, Injectors
12
Right Fan 1, Left Fan 2
13
A/C Clutch
14
Fuel Pump
15
Not Used
16
Horn
17
Left Fog Lamp, Right Fog Lamp,
Fog Lamp Indicator
5-107