Pontiac Grand Prix - 2002 Fuse Box Diagram

Pontiac Grand Prix - 2002 Fuse Box Diagram

2-15
Entering Programming Mode
To program features, your vehicle must be in this
programming mode. Follow these steps:
1.
Turn the ignition key to LOCK or OFF.
2.
Remove the MALL PGM fuse from the instrument
panel fuse block. See “Fuses and Circuit Breakers”
in the Index.
3.
Turn the ignition key to ACCESSORY.
4.
Count the number of chimes you hear. You will hear
up to four chimes, depending on vehicle content. See
“Multifunction Alarm Locks and Lighting Choices”
earlier in this section.
You can now program your choices. After programming
a feature, you can exit the programming mode at
any time.
Exiting Programming Mode
To exit programming mode, turn the key from
ACCESSORY to OFF and put the MALL PGM fuse
back into the instrument panel fuse block.
Delayed Illumination and Exit Lighting
With delayed illumination, the interior lamps will stay
on for about 25 seconds after all doors are closed.
With exit lighting, the interior lamps will come on and
stay on for about 25 seconds whenever you remove the
key from the ignition.
Programmable Modes
Mode 1:
Both Features Off – The interior lamps will
turn on or off at the same instant that a door is opened
or closed.
Mode 2:
Delayed Illumination Only – The interior
lamps will stay on for about 25 seconds after all the
doors are closed, or until you lock the doors.
Mode 3:
Exit Lighting Only – The interior lamps will
come on whenever you remove the key from the ignition
and stay on for about 25 seconds, or until you lock
the doors.
Mode 4:
Both Features On – This combines
Modes 2 and 3.
2-31
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse (see “Fuses and
Circuit Breakers” in the Index). If the engine still does
not start with the other key, your vehicle needs service.
If your vehicle does start, the first key may be faulty.
See your dealer who can service the PASS
-
Key III to
have a new key made. In an emergency, contact Pontiac
Roadside Assistance. See “Roadside Assistance” in the
Index for more information.
It is possible for the PASS
-
Key III decoder to learn
the transponder value of a new or replacement key.
Up to 10 additional keys may be programmed for the
vehicle. This procedure is for learning additional keys
only. If all the currently programmed keys are lost or do
not operate, you must see your dealer or a locksmith
who can service PASS
-
Key III to have keys made and
programmed to the system.
See your dealer or a locksmith who can service
PASS
-
Key III to get a new key blank that is cut exactly
as the ignition key that operates the system.
Canadian Owners:
If you lose or damage your keys,
only a GM dealer can service PASS
-
KEY III to have
new keys made. To program additional keys, you will
need two current driver’s keys, (black in color). You
must add a step to the procedure, “To program the
new key.”After Step 2, repeat Steps 1 and 2 with
the second current driver’s key, (black in color).
Then continue with Step 3.
To program the new key do the following:
1.
Verify that the new key has “PK3” stamped on it.
2.
Insert the master key in the ignition and start the
engine. If the engine will not start, see your dealer
for service.
3.
After the engine has started, turn the key to OFF, and
remove the key.
4.
Insert the key to be programmed and turn it to RUN
within five seconds of removing the original key.
5.
The SECURITY light will turn off once the key has
been programmed. It may not be apparent that the
SECURITY light went on due to how quickly the
key is programmed.
6.
Repeat Steps 1 through 5 if additional keys are
to be programmed.
2-50
Turn and Lane Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return to its
original position automatically.
An arrow on the instrument
panel cluster will flash
in the direction of the turn
or lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return to its
original position when you release it.
As you signal a turn or a lane change, if the arrow
flashes faster than normal, a signal bulb may be burned
out and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check for burned
-
out bulbs and then check
the fuse. See “Fuses and Circuit Breakers” in the Index.
A chime will sound if you leave the turn signal on for
more than 3/4 mile (1.2 km).
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high beam,
or high to low, pull the multifunction lever all the way
toward you. Then release it.
When the high beams
are on, this light on the
instrument panel cluster will
appear. While the high
-
beam
headlamps are on, the fog
lamps will not illuminate.
If your vehicle is equipped with the Head
-
Up
-
Display
(HUD), an arrow will appear in the display area to
indicate that the high beams are on. See
“Head
-
Up
-
Display (HUD)” in the Index for
more information.
2-68
Accessory Power Outlet
Your vehicle has a 12
-
volt outlet which can be used to
plug in electrical equipment such as a cellular telephone,
a compact disc player, etc. It is located on the
passenger’s side, near the floor.
Remove the tethered cap to use the outlet. When
not using the outlet, be sure to cover it with the
protective cap.
The accessory power outlet will only operate while the
ignition is on and for a few minutes after turning the
ignition off. If you would like to operate an accessory
for an extended period of time, see your dealer for
more information.
NOTICE:
When using accessory power outlets:
D
Maximum load of any outlet should not
exceed the fuse rating.
D
Be sure to turn off electrical equipment
when not in use. Leaving electrical
equipment on for extended periods can
drain the battery.
Certain electrical accessories may not be compatible with the
accessory power outlet and could result in blown vehicle or
adapter fuses. If you experience a problem, see your dealer
for additional information on the accessory power plugs.
NOTICE:
Adding some electrical equipment to your vehicle
can damage it or keep other things from working
as they should. This wouldn’t be covered by your
warranty. Check with your dealer before adding
electrical equipment, and never use anything that
exceeds the fuse rating.
When adding electrical equipment, be sure to follow the
proper installation instructions included with the equipment.
NOTICE:
Power outlets are designed for accessory plugs
only. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of
the power outlet can cause damage not covered
by your warranty.
2-75
The main components of the instrument panel are the following:
A.
Side Window Defogger Vents
B.
Fog Lamp Switch
C.
Multifunction Lever
D.
Instrument Panel Cluster
E.
Hazard Warning Button
F.
Horn
G.
Trip Computer (If Equipped) and/or Driver
Information Center (DIC)
H.
Instrument Panel Vents
I.
Interior Lamps Control
J.
Exterior Lamps Control
K.
Tilt Steering Wheel Control
L.
Audio Steering Controls (If Equipped)
M. Head Up Display (HUD) Controls (Option)
N.
Comfort Controls
O.
Ashtray and Cigarette Lighter
P.
Audio System
Q.
Glove Box
R.
Instrument Panel Fuse Block
2-88
Oil Pressure Light
United States
Canada
If you have a problem with your oil pressure, this light
may stay on after you start your engine, or come on
when you are driving.
This indicates that oil is not going through your engine
quickly enough to keep it lubricated. The engine could
be low on oil or could have some other oil problem.
Have it fixed right away.
The oil light could also come on in two other situations:
D
When the ignition is on but the engine is not running,
the light will come on as a test to show you it’s
working. The light will go out when you turn the
ignition to RUN. If it doesn’t come on with the
ignition on, you may have a problem with the fuse or
bulb. Have it fixed right away.
D
If you make a hard stop, the light may come on for a
moment. This is normal.
CAUTION:
Don’t keep driving if the oil pressure is low. If
you do, your engine can become so hot that it
catches fire. You or others could be burned.
Check your oil as soon as possible and have your
vehicle serviced.
NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.
2-99
Care of the Head-Up Display
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity of
the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry it.
Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If You Can’t See the HUD Image When the Ignition
Is On
D
Is anything covering the HUD unit?
D
Is the HUD dimmer setting bright enough?
D
Is the HUD image adjusted to the proper height?
D
Still no HUD image? Check the fuse in the
instrument panel fuse block. See “Fuses and Circuit
Breakers” in the Index.
If the HUD Image Is Not Clear
D
Is the HUD image too bright?
D
Are the windshield and HUD lens clean?
The windshield is part of the HUD system. If you ever
need a new windshield, be sure to get one designed for
HUD. If you don’t, the HUD image may look blurred
and out of focus.
6-10
Engine Compartment Overview
When you open the hood of a vehicle with a 3100 V6 (Code J) engine, you’ll see:
A.
Windshield Washer Fluid
B. Battery
C.
Underhood Fuse Block
D.
Radiator Fill Cap
E.
Engine Coolant Recovery Tank
F.
Power Steering Fluid Reservoir
G.
Engine Oil Fill Cap
H.
Engine Oil Dipstick
I.
Automatic Transaxle
Fluid Dipstick
J.
Brake Fluid Reservoir
K.
Engine Air Cleaner/Filter
6-11
When you open the hood of a vehicle with a the 3800 V6 (Code K) engine, you’ll see:
A.
Windshield Washer Fluid
B. Battery
C.
Underhood Fuse Block
D.
Radiator Fill Cap
E.
Engine Coolant Recovery Tank
F.
Power Steering Fluid Reservoir
(low in engine compartment)
G.
Engine Oil Dipstick
H.
Engine Oil Fill Cap
I.
Automatic Transaxle
Fluid Dipstick
J.
Brake Fluid Reservoir
K.
Engine Air Cleaner/Filter
6-12
When you open the hood of a vehicle with a 3800 V6 Supercharged (Code 1) engine, you’ll see:
A.
Windshield Washer Fluid
B. Battery
C.
Underhood Fuse Block
D.
Radiator Fill Cap
E.
Engine Coolant Recovery Tank
F.
Power Steering Fluid Reservoir
(low in engine compartment)
G.
Engine Oil Dipstick
H.
Engine Oil Fill Cap
I.
Automatic Transaxle
Fluid Dipstick
J.
Brake Fluid Reservoir
K.
Engine Air Cleaner/Filter
6-68
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring is protected by a circuit breaker in
the instrument panel fuse block. An electrical overload
will cause the lamps to go on and off, or in some cases
to remain off. If this happens, have your headlamp
system checked right away.
Windshield Wipers
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools.
If the overload is caused by some electrical problem,
have it fixed.
6-69
Power Windows and Other Power Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links in the wiring itself. This
greatly reduces the chance of fires caused by
electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating. Spare fuses are located in the instrument
panel. See “Underhood Fuse Block” in the Index.
Instrument Panel Fuse Block
Some fuses are in a fuse block located inside of the
glove box behind a small bin on the right side. To open,
pull the cover out. The fuse block is inside. On the back
edge of this cover is a fuse puller and a fuse usage chart.
To use the fuse puller, place the wide end of the fuse
puller over the plastic end of the fuse. Squeeze the ends
over the fuse and pull it out.
To reinstall the bin, position the lower end and turn
the top into position. Press on the sides until it snaps
into place.
6-70
Circuit Breaker
Description
HEADLAMP
Headlamps
SEAT
Power Seat, Power Lumbar
BLANK
Blank
PWR WDO
Power Windows
BLANK
Blank
Fuse
Description
BLANK
Blank
BLANK
Blank
MALL PGM
Mall Module
--
Program
MALL
Mall Module
WIPER
Wipers
STR
WHL ILLUM
Steering Wheel Illumination
BLANK
Blank
STR WHL CTRL
Steering Wheel Control
SUNROOF
Sunroof
RADIO
Radio
BLANK
Blank
RADIO AMP
Bose Amplifier
PWR LOCK
Mall Module
--
Power Locks
HSEAT/LUM
Heated Seats, Power Lumbar
R DEFOG
Rear Defog
PASSKEY III
PASS
-
Key
R
III Security System
6-71
Fuse
Description
RAP
Retained Accessory Power
HAZARD
Hazard Flashers
PWR MIR
Power Mirrors
HVAC HI
HVAC Blower
--
Hi
CIG LTR
Cigarette Lighter, ALDL, Floor
Console Accessory Outlet
INT LAMP
Mall Module
--
Interior lamps
STOP LAMP
Stoplamp
ONSTAR
OnStar
R
System
BLANK
Blank
ECM
Electronic Control Module
CRUISE
Cruise Control
I/P
-
IGN
Chime/Mall Module, Cluster,
Trip Computer, Head
-
Up
Display, Automatic Transaxle
Shift Lock Control
SIR
Supplemental Inflatable Restraint
(Air Bag)
TURN
Turn Signal
Fuse
Description
BLANK
Blank
BLANK
Blank
BLANK
Blank
BLANK
Blank
BTSI
Automatic Transaxle Shift
Lock Control
BLANK
Blank
BLANK
Blank
BLANK
Blank
HVAC CTRL
Blower Control, HVAC
DIC/HVAC
Rear Defog, HVAC, Driver
Information Center, Daytime
Running Lamps, Heated Seats
BLANK
Blank
BLANK
Blank
PWR DROP
Power Drop Ignition
CANISTER
VENT
Canister Vent Solenoid
DRL
Daytime Running Lamps
6-72
Underhood Fuse Block
Some fuses are located in a
fuse block in the engine
compartment on the
passenger’s side. Pull off
the cover labeled FUSES to
expose the fuses.
Fuse
Description
1
Cooling Fan 2
2
Spare
3
Headlamps
4
Battery Main 2
5
Ignition Main 1
6-73
Fuse
Description
6
Cooling Fan 1
7
Battery Main 1
8
Ignition Main 2
18
Fuel Injections
19
Spare
20
Spare
21
Mass Air Flow (MAF),
Heated Sensors, Canister Purge,
Boost Solenoid
22
Spare
23
Spare
24
Spare
25
Ignition Module
26
Spare
27
Trunk Release, Back
-
Up Lamps
28
AC Clutch, ABS Ignition
Fuse
Description
29
Remote Keyless Entry,
Theft
-
Deterrent, Trip Computer,
HVAC Module, Security LED
30
Alt Sense
31
Torque Converter Clutch (TCC)
32
Fuel Pump
33
Electronic Control
Module/Powertrain
Control Module
34
Spare
35
Fog Lamps
36
Horn
37
Chime/Mall Module, Taillamps,
Parking Lamps, Sidemarker
Lamps, Dimmable Lamps
38
Spare Fuse
39
Air Pump
40
Mini Fuse Puller