Pontiac Bonneville - 2002 Fuse Box Diagram

Pontiac Bonneville - 2002 Fuse Box Diagram

2-22
If the SECURITY light comes on for one minute
and then shuts off while the ignition is on, the security
system has detected a problem. See your dealer
for service.
If a door is opened without the key or remote keyless
entry transmitter, or if the door key cylinders are
damaged, the alarm will go off. The exterior lamps will
flash and the horn will sound for 30 seconds, then will
go off in order to save battery power.
Remember, the theft
-
deterrent system won’t activate if
you lock the doors with a key or manual door lock. It
activates only if you use a power door lock switch while
the door is open, or the remote keyless entry transmitter.
Avoid setting off the alarm by accident.
Always unlock a door with a key, or use the remote
keyless entry transmitter. Unlocking a door any other
way will set off the alarm.
If you set off the alarm by accident, unlock the driver’s
door with your key. You can also turn off the alarm by
pressing the button with the unlock symbol on the
remote keyless entry transmitter. The alarm won’t stop if
you try to unlock a door any other way.
Testing the Alarm
1.
From inside the vehicle, roll down the window.
2.
Activate the system by locking the doors with the
power door lock switch while the door is open, or
with the remote keyless entry transmitter.
3.
Get out of the vehicle, close the door and wait for the
SECURITY light to go out.
4.
Then, reach in through the window, unlock the door
with the manual door lock and open the door. This
should set off the alarm.
If the alarm does not sound when it should, check to see
if the horn works. The horn fuse may be blown. To
replace the fuse, see “Fuses and Circuit Breakers” in
the Index.
If the alarm does not sound, or the exterior lamps do not
flash, see your dealer.
2-24
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
This device complies with RSS
-
210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications to this system by other than an
authorized service facility could void authorization to
use this equipment.
PASS
-
Key III uses a radio frequency transponder in the
key that matches a decoder in your vehicle.
When the PASS
-
Key III system senses that someone is
using the wrong key, it shuts down the vehicle’s starter
and fuel systems. The starter will not work and fuel will
stop being delivered to the engine. Anyone using a
trial
-
and
-
error method to start the vehicle will be
discouraged because of the high number of electrical
key codes.
When trying to start the vehicle, if the engine does not
start and the SECURITY light comes on, the key may
have a damaged transponder. Turn the ignition off and
try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse (see “Fuses and
Circuit Breakers” in the Index). If the engine still does
not start with the other key, your vehicle needs service.
If your vehicle does start, the first key may be faulty.
See your dealer who can service the PASS
-
Key III to
have a new key made.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 keys may be programmed for the vehicle. This
procedure is for learning additional keys only.
2-41
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up
or down. When the turn is finished, the lever will
return automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
If the arrows flash very fast as you signal a turn or a lane
change, a signal bulb may be burned out and other
drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. See “Bulb Replacement” in the Index. If the
arrows don’t go on at all when you signal a turn, check
the fuse. See “Fuses and Circuit Breakers” in the Index.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile
(1.2 km), a chime will sound at each flash of the turn
signal. To turn off the chime, move the turn signal lever
to the off position.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high beam,
push the lever forward. To change from high beam to
low beam, pull the turn signal lever toward you, then
release it.
When the high beams are
on, this light on the
instrument panel cluster
will also be on.
2-59
The cigarette lighter is located next to the storage tray.
To use a lighter, just push the center in all the way and
let it go. When it is ready, the center will pop back out
by itself. Pull out the entire unit to use it.
NOTICE:
Don’t hold a cigarette lighter in with your hand
while it is heating. If you do, it won’t be able to
back away from the heating element when it’s
ready. That can make it overheat, damaging the
lighter and the heating element.
The cigarette lighter will only operate when the ignition
key is in ON and for 10 minutes after turning the
ignition OFF. If you would like the lighter to operate
regardless of ignition position, and for extended periods
of time, see “Engine Compartment Fuse Block” in the
Index or see your dealer.
Sun Visors
To block out glare, you can swing down the visors. You
can also remove them from the center mount and swing
them to the side, while the auxiliary sunshade remains to
block glare from the front.
Visor Vanity Mirror
Open the cover to expose the vanity mirror.
If your vehicle has the optional lighted vanity mirrors,
the lamps come on when you open the cover.
Air Inflator System (Option)
Some vehicles have an air inflator located in the trunk
for use in maintaining proper air pressure for the tires.
2-60
The air inflator will work only with the ignition on.
CAUTION:
Inflating something too much can make it
explode, and you or others could be injured. Be
sure to read the inflator instructions, and inflate
any object only to its recommended pressure.
Pressing the AIR button will activate the inflator for
ten minutes.
The air inflator comes with a kit that includes a 20
-
foot
(6.1 m) hose and an air pressure gage, as well as
instructions and special adapters for inflating things like
an air mattress or a basketball.
Accessory Power Outlet
With the accessory power outlet you can plug in
auxiliary electrical equipment such as a cellular
telephone or CB radio.
The accessory power outlet (12
-
volt) is located inside
the overhead console (if equipped) and at the rear of the
front console (if equipped). If your vehicle is equipped
with an overhead console, access the accessory power
outlet by sliding the access door to the side. If your
vehicle is equipped with a floor console, the power
outlet is at the rear of the floor console.
To use the outlet, remove the protective cap which
covers it. When not using it, always cover the outlet
with the protective cap.
The accessory power outlet will only operate when the
ignition key is in ON and for 10 minutes after turning
the ignition OFF. If you would like the accessory power
outlet to operate regardless of ignition position, and
for extended periods of time, see “Engine Compartment
Fuse Block” in the Index or see your dealer for
more information.
2-61
NOTICE:
When using accessory power outlets:
D
Maximum load of any electrical equipment
should not exceed 15 amps.
D
Be sure to turn off any electrical equipment
when not in use. Leaving electrical
equipment on for extended periods can
drain the battery.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result in
blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information on
accessory power outlets.
NOTICE:
Adding some electrical equipment to your vehicle
can damage it or keep other things from working
as they should. This wouldn’t be covered by your
warranty. Check with your dealer before adding
electrical equipment, and never use anything that
exceeds the amperage rating.
When adding electrical equipment, be sure to follow
the proper installation instructions included with
the equipment.
NOTICE:
Power outlets are designed for accessory plugs
only. Do not hang any type of accessory or
accessory bracket from the plug. Improper use of
the power outlet can cause damage not covered
by your warranty.
2-111
2.
Adjust the seat, if necessary, before setting the height
using the IMAGE switch.
Press and hold the top of the IMAGE switch, raising
the HUD image as far as possible. Then press on the
bottom of the HUD IMAGE switch to move the
image down, so the image is as low as possible, but
in full view.
3.
Turn the INTENSITY knob counterclockwise until
the HUD image is no brighter than necessary. To turn
the HUD off, turn the HUD INTENSITY knob all
the way counterclockwise.
If the sun comes out, or it becomes cloudy, or if you turn
on your headlamps, you may need to adjust the HUD
brightness using the HUD INTENSITY knob. Polarized
sunglasses could make the HUD image harder to see.
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity of
the HUD image.
Spray household glass cleaner on a soft, clean cloth.
Wipe the HUD lens gently, then dry it. Do not spray
cleaner directly on the lens, because the cleaner fluid
could leak inside the unit.
If you can’t see the HUD image when the ignition is on,
check to see if:
D
The HUD unit is covered,
D
the HUD INTENSITY knob is adjusted correctly,
D
the HUD image is adjusted to the proper height, or
D
a fuse in the fuse panel may have blown. See “Fuses
and Circuit Breakers” in the Index.
If the HUD image is not clear, it could be too bright.
Move the HUD INTENSITY knob counterclockwise.
You may need to clean the windshield and HUD lens.
Your windshield is part of the HUD system. If you ever
have to have a new windshield, be sure to get one
designed for HUD. If you don’t, the HUD image may
look blurred and out of focus.
6-11
Engine Compartment Overview
When you open the hood on the 3800 (L36) engine (3800 Supercharged (L67) engine similar), here’s what you will see:
A.
Engine Compartment Fuse Block
B.
Windshield Washer
Fluid Reservoir
C.
Engine Coolant Recovery Tank
D.
Radiator Pressure Cap
E.
Power Steering Fluid Reservoir
F.
Engine Oil Dipstick
G.
Engine Oil Fill Cap
H.
Automatic Transaxle
Fluid Dipstick
I.
Brake Master Cylinder
J.
Engine Air Cleaner/Filter
6-67
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring is protected by an internal circuit
breaker. An electrical overload will cause the lamps to
go on and off, or in some cases to remain off. If this
happens, have your headlamp system checked
right away.
Windshield Wipers
The windshield wiper motor is protected by an internal
circuit breaker and a fuse. If the motor overheats due to
heavy snow, etc., the wiper will stop until the motor
cools. If the overload is caused by some electrical
problem, be sure to have it fixed.
Power Windows and Other Power Options
Circuit breakers in the rear fuse block protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed or
goes away.
6-68
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses and circuit
breakers. This greatly reduces the chance of damage
caused by electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating.
The MaxiFuses are located in two fuse blocks, one
located in the engine compartment on the passenger’s
side and the other under the rear seat on the driver’s
side. If a MaxiFuse should blow, have your vehicle
serviced by your dealer immediately.
Removing Fuses
You will find a fuse puller attached in both of the fuse
blocks. Snap the wide end of the fuse puller on to the
fuse, at the side indentations holding the puller and pull
the fuse out.
Engine Compartment Fuse Block
As mentioned previously,
the engine compartment
fuse block is located in the
front of the engine
compartment on the
passenger’s side. Lift the
cover to gain access.
Fuse 22 or 23 can be moved to the outer position to
enable the accessory power outlet or cigarette lighter
when the ignition is not on. See your dealer for
additional assistance, if needed.
6-69
Minifuse
Usage
1
Not Used
2
Accessory
3
Windshield Wipers
4
Not Used
5
Headlamp Low Beam Left
Minifuse
Usage
6
Headlamp Low Beam Right
7
Spare
8
Powertrain Control
Module Battery
9
Headlamp High Beam Right
10
Headlamp High Beam Left
11
Ignition 1
12
Not Used
13
Transaxle
14
Cruise Control
15
Direct Ignition System
16
Injector Bank #2
17
Not Used
18
Not Used
19
Powertrain Control
Module Ignition
6-70
Minifuse
Usage
20
Oxygen Sensor
21
Injector Bank #1
22
Auxiliary Power
23
Cigar Lighter
24
Fog Lamps/Daytime
Running Lamps
25
Horn
26
Air Conditioning Clutch
Micro Relay
Usage
27
Headlamp High Beam
28
Headlamp Low Beam
29
Fog Lamps
30
Daytime Running Lamps
Micro Relay
Usage
31
Horn
32
Air Conditioning Clutch
33
HVAC Solenoid
Mini Relay
Usage
34
Accessory
35
Air Pump
36
Starter 1
37
Cooling Fan Secondary
38
Ignition 1
39
Cooling Fan Series/Parallel
40
Cooling Fan Primary
6-71
Maxibreaker
Usage
41
Starter
Maxifuse
Usage
42
A.I.R.
43
Not Used
44
Antilock Brake System
45
Not Used
46
Cooling Fan Secondary
47
Cooling Fan Primary
48
Spare
49
Spare
50
Spare
51
Spare
52
Spare
53
Fuse Puller
Removing the Rear Seat Cushion
NOTICE:
The battery and main fuse blocks are located
under the rear seat cushion. The battery’s ground
terminal and some relay wires are exposed.
To help avoid damage to the battery and wires,
be careful when removing or reinstalling the
seat cushion. Do not remove covers from covered
parts. Do not store anything under the seat, as
objects could touch exposed wires and cause
a short.
To remove the rear seat cushion, do the following:
1.
Pull up on the front of the cushion to release the
front hooks.
2.
Pull the cushion up and out toward the front of
the vehicle.
6-73
2.
Slide the rear of the cushion up and under the
seatback so the rear locating guides hook into the
wire loops on the back frame.
3.
With the seat cushion lowered, push rearward and
then press down on the seat cushion until the spring
locks on both ends engage.
4.
Check to make sure the safety belts are properly
routed and that no portion of any safety belt is
trapped under the seat. Also make sure the seat
cushion is secured.
Rear Underseat Fuse Block
The rear fuse block is
located below the rear
seat on the driver’s side.
The rear seat cushion must
be removed to access the
fuse block. See “Removing
the Rear Seat Cushion” in
the Index.
6-74
Minifuse
Usage
1
Fuel Pump
2
Heater, Ventilation, Air
Conditioning Blower
3
Memory Seat
4
Assembly Line Diagnostic Link
5
Not Used
6
Compact Disc (CD)
Minifuse
Usage
7
Driver Door Module
8
Supplemental Inflatable Restraint
9
Not Used
10
Lamps Park Right
11
Ventilation Solenoid
12
Ignition 1
13
Lamps Park Left
14
Interior Lamp Dimmer Module
15
Not Used
16
Heated Seat Left Front
17
Not Used
18
Rear Door Modules
19
Stoplamps
20
PARK (P) / REVERSE (R)
21
Audio
22
Retained Accessory Power
6-75
Minifuse
Usage
23
Not Used
24
Not Used
25
Passenger Door Module
26
Body
27
Interior Lamps
28
Not Used
29
Ignition Switch
30
Instrument Panel
31
Heated Seat Right Front
32
Not Used
33
Heating, Ventilation,
Air Conditioning
34
Ignition 3 Rear
35
Antilock Brake System
36
Turn Signal/Hazard
37
HVAC Battery
38
Dash Integration Module
Micro Relay
Usage
39
Fuel Pump
40
Parking Lamps
41
Ignition 1
42
Rear Fog Lamps
43
Not Used
44
Park Brake
45
Reverse Lamps
46
Retained Accessory Power
47
Fuel Tank Door Lock
48
Not Used
49
Ignition 3
50
Fuel Tank Door Release
51
Interior Lamps
52
Trunk Release
53
Front Courtesy Lamps
54
Not Used
55
Electronic Level
Control Compressor
6-76
Circuit Breaker
Usage
56
Power Seats
57
Power Windows
Mini Relay
Usage
58
Cigarette Lighter
59
Rear Defog
Maxifuse
Usage
60
Not Used
61
Rear Defog
62
Not Used
63
Audio Amplifier
64
Electronic Level Control
Compressor/Exhaust
Maxifuse
Usage
65
Cigarette Lighter
66
Not Used
67
Spare
68
Spare
69
Spare
70
Spare
71
Spare
72
Spare
73
Spare
74
Spare
75
Fuse Puller