Pontiac Grand Prix - 2001 Fuse Box Diagram

Pontiac Grand Prix - 2001 Fuse Box Diagram

2-14
Entering Programming Mode
To program features, your vehicle must be in this
programming mode. Follow these steps:
1.
Turn the ignition key to LOCK or OFF.
2.
Remove the MALL PGM fuse from the instrument
panel fuse block. See “Fuses and Circuit Breakers”
in the Index.
3.
Turn the ignition key to ACCESSORY.
4.
Count the number of chimes you hear. You will hear
up to four chimes, depending on vehicle content. See
“Multifunction Alarm Locks and Lighting Choices”
earlier in this section.
You can now program your choices. After programming
a feature, you can exit the programming mode at
any time.
Exiting Programming Mode
To exit programming mode, turn the key from
ACCESSORY to OFF and put the MALL PGM fuse
back into the instrument panel fuse block.
Delayed Illumination and Exit Lighting
With delayed illumination, the interior lamps will stay
on for about 25 seconds after all doors are closed.
With exit lighting, the interior lamps will come on and
stay on for about 25 seconds whenever you remove the
key from the ignition.
Programmable Modes
Mode 1:
Both Features Off (The interior lamps will
turn on or off at the same instant that a door is
opened or closed.)
Mode 2:
Delayed Illumination Only (The interior lamps
will stay on for about 25 seconds after all the doors are
closed, or until you lock the doors.)
Mode 3:
Exit Lighting Only (The interior lamps will
come on whenever you remove the key from the ignition
and stay on for about 25 seconds, or until you lock
the doors.)
Mode 4:
Both Features On (This combines Modes 2 and 3.)
2-29
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
This device complies with RSS
-
210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation of
the device.
Changes or modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
PASS
-
Key III uses a radio frequency transponder in the
key that matches a decoder in your vehicle.
When the PASS
-
Key III system senses that someone is
using the wrong key, it shuts down the vehicle’s starter
and fuel systems. The starter will not work and fuel will
stop being delivered to the engine. Anyone using a
trial
-
and
-
error method to start the vehicle will be
discouraged because of the high number of electrical
key codes.
When trying to start the vehicle if the engine does not
start and the SECURITY light comes on, the key may
have a damaged transponder. Turn the ignition off and
try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse (see “Fuses and
Circuit Breakers” in the Index). If the engine still does
not start with the other key, your vehicle needs service.
If your vehicle does start, the first key may be faulty.
See your dealer who can service the PASS
-
Key III to
have a new key made. In an emergency, contact Pontiac
Roadside Assistance. See “Roadside Assistance” in the
Index for more information.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only.
If all the currently programmed keys are lost or do not
operate, you must see your dealer or a locksmith who
can service PASS
-
Key III to have keys made and
programmed to the system.
See your dealer or a locksmith who can service
PASS
-
Key III to get a new key blank that is cut
exactly as the ignition key that operates the system.
2-48
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check for burned
-
out bulbs and then check
the fuse (see “Fuses and Circuit Breakers” in the Index).
A chime will sound if you leave the turn signal on for
more than 3/4 mile (1.2 km).
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high beam,
or high to low, pull the multifunction lever all the way
toward you. Then release it.
When the high beams
are on, a light on the
instrument panel cluster
also will be on. While
the high
-
beam headlamps
are on, the fog lamps will
not be illuminated.
Flash-to-Pass Feature
When the headlamps are off, pull the lever toward you
to momentarily turn on the high beams (to signal that
you are going to pass). When you release the lever,
they will turn off and stay off.
Windshield Wipers
You control the windshield wipers by turning the band
marked WIPER on the turn signal/multifunction lever.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle. If you want more cycles, hold the
band on MIST longer.
For steady wiping at low speed, turn the band to LOW.
For high
-
speed wiping, turn the band further, to HIGH.
To stop the wipers, turn the band to OFF.
You can set the wiper speed for a long or short delay
between wipes. This can be very useful in light rain or
snow. Turn the band to choose the delay time. The
closer to LOW, the shorter the delay.
Be sure to clear ice and snow from the wiper blades
before using them. If they’re frozen to the windshield,
carefully loosen or thaw them. If the blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload the wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.
2-65
Sun Visors
To block out glare, you can swing down the visors.
You can also swing them from front to side.
Visor Vanity Mirrors
Open the cover to expose the vanity mirror. If the
vehicle has the optional lighted vanity mirrors, the
lamps come on when you open the cover.
Accessory Power Outlet
Your vehicle has a 12
-
volt outlet which can be used to
plug in electrical equipment such as a cellular telephone,
a compact disc player, etc. It is located on the
passenger’s side, near the floor. Remove the tethered
cap to use the outlet.
Certain accessory power plugs may not be compatible to
the accessory power outlet and could result in blown
vehicle or adapter fuses. If you experience a problem,
see your dealer for additional information on the
accessory power plugs.
NOTICE:
Adding some electrical equipment to your vehicle
can damage it or keep other things from working
as they should. This wouldn’t be covered by your
warranty. Check with your dealer before adding
electrical equipment, and never use anything that
exceeds the fuse rating.
Auxiliary Power Connection
(Power Drop)
The vehicle is equipped with auxiliary power
connections. This feature can be used to power
aftermarket electrical equipment added to the vehicle.
The connections are located on the passenger’s side of
the vehicle, below the glove box.
2-71
The main components of the instrument panel are listed here:
A.
Side Window Defogger Vents
B.
Fog Lamp Switch
C.
Multifunction Lever
D.
Instrument Panel Cluster
E.
Hazard Button
F.
Horn, Driver’s Side Air Bag
G.
Trip Computer/Driver Information Center (DIC)
H.
Instrument Panel Vents
I.
Interior Lamp Control
J.
Exterior Lamp Control
K.
Tilt Wheel Control
L.
Audio Steering Controls (If Equipped)
M. HUD Display Controls (Option)
N.
Comfort Controls
O.
Ashtray and Cigarette Lighter
P.
Audio System
Q.
Glove Box
R.
Instrument Panel Fuse Block
2-84
Oil Warning Light
United States
Canada
If you have a problem with your oil pressure, this light
may stay on after you start your engine, or come on
when you are driving.
This indicates that oil is not going through your engine
quickly enough to keep it lubricated. The engine could
be low on oil or could have some other oil problem.
Have it fixed right away.
The oil light could also come on in two other situations:
D
When the ignition is on but the engine is not running,
the light will come on as a test to show you it’s
working. The light will go out when you turn the
ignition to RUN. If it doesn’t come on with the
ignition on, you may have a problem with the fuse or
bulb. Have it fixed right away.
D
If you make a hard stop, the light may come on for a
moment. This is normal.
CAUTION:
Don’t keep driving if the oil pressure is low.
If you do, your engine can become so hot that it
catches fire. You or others could be burned.
Check your oil as soon as possible and have your
vehicle serviced.
NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.
2-95
Care of the Head-Up Display
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity of
the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry it.
Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If You Can’t See the HUD Image When the Ignition
Is On
D
Is anything covering the HUD unit?
D
Is the HUD dimmer setting bright enough?
D
Is the HUD image adjusted to the proper height?
D
Still no HUD image? Check the fuse in the
instrument panel fuse block. See “Fuses and Circuit
Breakers” in the Index.
If the HUD Image Is Not Clear
D
Is the HUD image too bright?
D
Are the windshield and HUD lens clean?
The windshield is part of the HUD system. If you ever
need a new windshield, be sure to get one designed for
HUD. If you don’t, the HUD image may look blurred
and out of focus.
6-64
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting
to add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring is protected by a circuit breaker in
the instrument panel fuse block. An electrical overload
will cause the lamps to go on and off, or in some cases
to remain off. If this happens, have your headlamp
system checked right away.
Windshield Wipers
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools.
If the overload is caused by some electrical problem,
have it fixed.
Power Windows and Other Power Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links in the wiring itself. This greatly
reduces the chance of fires caused by electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating. Spare fuses are located in the instrument
panel. See “Underhood Electrical Center” in the Index.
6-65
Instrument Panel Fuse Block
Some fuses are in a fuse block located inside of the
glove box behind a small bin on the right side. To open,
pull the cover out. The fuse block is inside. On the back
edge of this cover is a fuse puller and a fuse usage chart.
To use the fuse puller, place the wide end of the fuse
puller over the plastic end of the fuse. Squeeze the ends
over the fuse and pull it out.
To reinstall the bin, position the lower end and turn
the top into position. Press on the sides until it snaps
into place.
Circuit Breaker
Description
HEADLAMP
Headlamps
SEAT
Power Seat, Power Lumbar
BLANK
Blank
PWR WDO
Power Windows
BLANK
Blank
6-66
Fuse
Description
BLANK
Blank
BLANK
Blank
MALL PGM
Mall Module
--
Program
MALL
Mall Module
WIPER
Wipers
STR WHL
ILLUM
Steering Wheel Illumination
BLANK
Blank
STR WHL
CTRL
Steering Wheel Control
SUNROOF
Sunroof
RADIO
Radio
BLANK
Blank
RADIO AMP
Bose Amplifier
PWR LOCK
Mall Module
--
Power Locks
HSEAT/LUM
Heated Seats, Power Lumbar
R DEFOG
Rear Defog
PASSKEY III
PASS
-
Key
R
III Security System
Fuse
Description
RAP
Retained Accessory Power
HAZARD
Hazard Flashers
PWR MIR
Power Mirrors
HVAC HI
HVAC Blower
--
Hi
CIG LTR
Cigarette Lighter, ALDL,
Floor Console Accessory Outlet
INT LAMP
Mall Module
--
Interior lamps
STOP LAMP
Stoplamp
ONSTAR
OnStar
R
System
BLANK
Blank
ECM
Electronic Control Module
CRUISE
Cruise Control
I/P
-
IGN
Chime/Mall Module, Cluster,
Trip Computer, Head
-
Up Display,
Automatic Transaxle Shift
Lock Control
SIR
Supplemental Inflatable Restraint
(Air Bag)
TURN
Turn Signal
6-67
Fuse
Description
BLANK
Blank
BLANK
Blank
BLANK
Blank
BLANK
Blank
BTSI
Automatic Transaxle Shift
Lock Control
BLANK
Blank
BLANK
Blank
BLANK
Blank
HVAC CTRL
Blower Control, HVAC
DIC/HVAC
Rear Defog, HVAC, Driver
Information Center, Daytime
Running Lamps, Heated Seats
BLANK
Blank
BLANK
Blank
PWR DROP
Power Drop Ignition
CANISTER
VENT
Canister Vent Solenoid
DRL
Daytime Running Lamps
Underhood Electrical Center
--
Passenger’s Side
Some fuses are in a fuse
block on the passenger’s
side of the engine
compartment. Pull off
the cover labeled FUSES
to expose the fuses.
6-68
Fuse
Description
1
Cooling Fan 2
2
Spare
3
Headlamps
4
Battery Main 2
5
Ignition Main 1
6
Cooling Fan 1
Fuse
Description
7
Battery Main 1
8
Ignition Main 2
18
Fuel Injections
19
Spare
20
Spare
21
Mass Air Flow (MAF),
Heated Sensors, Canister Purge,
Boost Solenoid
22
Spare
23
Spare
24
Spare
25
Ignition Module
26
Spare
27
Trunk Release, Back
-
Up Lamps
28
AC Clutch, ABS Ignition
29
Remote Keyless Entry,
Theft
-
Deterrent, Shock Sensor,
Trip Computer, HVAC Module,
Security LED
6-69
Fuse
Description
30
Alt Sense
31
Torque Converter Clutch (TCC)
32
Fuel Pump
33
Electronic Control
Module/Powertrain
Control Module
34
Spare
35
Fog Lamps
36
Horn
37
Chime/Mall Module, Taillamps,
Parking Lamps, Sidemarker
Lamps, Dimmable Lamps
38
Spare Fuse
39
Air Pump
40
Spare
Diode
Description
Air Conditioning Clutch Diode
Relay
Description
9
Cooling Fan
10
Cooling Fan 2
11
Ignition Main
12
Cooling Fan 1
13
Air Conditioning Clutch
14
Fuel Pump
15
Fuel Pump Speed Cont
16
Horn
17
Fog Lamp