Pontiac Aztek - 2001 Fuse Box Diagram

Pontiac Aztek - 2001 Fuse Box Diagram

2-26
This device complies with RSS
-
210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation of
the device.
Changes or modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
PASS
-
Key III uses a radio frequency transponder in
the key that matches a decoder in your vehicle.
When the PASS
-
Key III system senses that someone
is using the wrong key, it shuts down the vehicle’s
starter and fuel systems. The starter will not work and
fuel will stop being delivered to the engine. Anyone
using a trial
-
and
-
error method to start the vehicle will
be discouraged because of the high number of electrical
key codes.
When trying to start the vehicle if the engine does not
start and the SECURITY message comes on, the key
may have a damaged transponder. Turn the ignition off
and try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse (see “Fuses and
Circuit Breakers” in the Index). If the engine still does
not start with the other key, your vehicle needs service.
If your vehicle does start, the first key may be faulty.
See your dealer who can service the PASS
-
Key III to
have a new key made.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only.
If all the currently programmed keys are lost or do not
operate, you must see your dealer or a locksmith who
can service PASS
-
Key III to have keys made and
programmed to the system.
See your dealer who can service PASS
-
Key III to get a
new key blank that is a cut exactly as the ignition key
that operates the system.
2-44
Turn Signal and Lane-Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow
you to signal a turn or a lane change.
To signal a turn, move the lever all the way up
or down. When the turn is finished, the lever will
return automatically.
An arrow on the
instrument panel cluster
and the optional HUD
display will flash in the
direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or a lane change, if the arrow
flashes faster than normal, a signal bulb may be
burned out and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check for burned
-
out bulbs and check the
fuse (see “Fuses and Circuit Breakers” in the Index).
If you have a trailer towing option with added wiring
for the trailer lamps, the signal indicator will flash at a
normal rate even if a turn signal bulb is burned out.
Check the front and rear turn signal lamps regularly to
make sure they are working.
Turn Signal On Chime
If either turn signal is left on for more than 3/4 mile
(1.2 km), a chime will sound to let the driver know to
turn it off.
If you need to leave the signal on for more than 3/4 mile
(1.2 km), turn off the signal and then turn it back on.
2-72
To use your air
inflator system do
the following:
1.
Turn the ignition to ACC or ON.
2.
Attach the appropriate nozzle adapter, if required,
to the end of the hose that has the pressure gage.
3.
Then attach that end of the hose to the object you
wish to inflate.
4.
Remove the protective cap covering the accessory
power outlet.
5.
Attach the other end of the hose to the outlet.
6.
Then press the ON switch.
If the air inflator system does not turn on, the fuse may
be blown or installed incorrectly. See “Fuses and Circuit
Breakers” in the Index or see your dealer for service.
Your air inflator will automatically shut off after about
10 minutes. To reset, press the ON switch again.
Don’t run your air inflator for longer than 30 minutes
at one time. If you do, you may damage the system.
After 30 minutes, wait at least 10 minutes before
restarting the air inflator.
To turn off the inflator, press OFF and detach the
hose from the inflated object first, then from the outlet.
Replace the protective cap. Place the inflator kit tools in
the pouch, and store in the glove box.
2-73
Accessory Power Outlets
Certain power accessory plugs may not be compatible to
the power accessory outlet and could result in blown
vehicle or adapter fuses. If you experience a problem,
see your dealer for additional information on the power
accessory plugs.
Power outlets can be used to plug in electrical
equipment such as a cellular telephone, CB radio, etc.
Follow the proper installation instructions that are
included with any electrical equipment you install.
There are two front power outlets when the optional
cigarette lighter is not in use. One is located on the
center console switchbank. The other is located on the
floor console above the vents. Pull the cover down to
use a power outlet. When not in use, replace the cover.
There are two rear power outlets. One is located in the
rear of the floor console below the vents. The other is
located in the rear of the vehicle on the driver’s side.
Pull the cover down to use the power outlet.
When not in use, always cover the accessory power
outlets with the protective cap.
NOTICE:
When using the accessory power outlets:
D
Maximum load of any electrical equipment
should not exceed 20 amps.
D
Be sure to turn off any electrical equipment
when not in use. Leaving electrical equipment
on for extended periods can drain your battery.
2-79
The main components of the instrument panel are:
A.
Side Vents
B.
Instrument Panel Cluster
C.
Hazard Warning Flasher Switch
D. Head
-
Up Display Switch and Driver
Information Center (DIC) Controls (If Equipped)
or DIC Controls (If Equipped)
E.
Center Vents
F.
Audio System
G.
Side Vents
H.
Turn Signal/Multifunction Lever
I.
Exterior/Interior Lamp Switch
J.
Audio Steering Wheel Controls (If Equipped)
K.
Hood Release
L.
Parking Brake
M. Horn
N.
Ignition Switch
O.
Audio Steering Wheel Controls (If Equipped)
P.
Shift Lever
Q.
Accessory Power Outlets
R.
Rear Vents
S.
Console/Cooler (Option)
T.
Instrument Panel Fuse Block
U.
Cupholders and Ashtray (Option)
V.
Center Console Switchbank
W. Accessory Power Outlet or Cigarette
Lighter (Option)
X.
Comfort Controls
Y.
Glove Box
2-116
To adjust the HUD so you can see it properly:
1.
Start your engine and turn the dimmer switch knob
to the desired HUD image brightness.
The brightness of the HUD image is determined by
the ambient light conditions in the direction your
vehicle is facing and where you have the HUD
dimmer control set. If you are facing a dark object or
a heavily shaded area, your HUD may anticipate that
you are entering a dark area and may begin to dim.
2.
Adjust the driver’s seat. If you change your seat
position later, you may have to readjust your HUD.
3.
Press the UP or DN buttons until the HUD image is
easy to see and then press the DN switch until the
HUD image is as low as possible, but, remains in
full view straight ahead near the front bumper.
The HUD image can only be adjusted up and down,
not side
-
to
-
side.
4.
To turn the image off, turn the dimmer knob
counterclockwise to OFF.
If the sun comes out or it becomes cloudy, you may
need to adjust the HUD brightness again using the
dimmer control. Polarized sunglasses could make the
HUD image harder to see.
To change from English to metric units, push the
MODE button located to the right of the steering wheel.
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity of
the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry it.
Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you can’t see the HUD image,
check to see if one of the following has occurred:
D
Something is covering the HUD unit.
D
The HUD dimmer control is adjusted properly.
D
The HUD image is adjusted to the proper height.
D
Ambient light (in the direction your vehicle is facing)
is low.
D
A fuse is blown. See “Fuses and Circuit Breakers”
in the Index.
Keep in mind that your windshield is part of the
HUD system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD or
your HUD image may look blurred and out of focus.
5-5
5.
Your vehicle has a
remote positive (+) jump
starting terminal. The
terminal is under a
tethered cap at the front
of the underhood fuse
and relay center. See
“Engine Compartment
Overview” in the Index
for more information.
Flip the cap up to access the remote
positive (+) terminal.
You should always use the remote positive (+)
terminal instead of the positive (+) terminal on
your battery.
CAUTION:
Using a match near a battery can cause battery
gas to explode. People have been hurt doing this,
and some have been blinded. Use a flashlight if
you need more light.
Be sure the battery has enough water. You don’t
need to add water to the ACDelco
R
battery
installed in every new GM vehicle. But if a
battery has filler caps, be sure the right amount
of fluid is there. If it is low, add water to take
care of that first. If you don’t, explosive gas could
be present.
Battery fluid contains acid that can burn you.
Don’t get it on you. If you accidentally get it in
your eyes or on your skin, flush the place with
water and get medical help immediately.
6-10
Engine Compartment Overview
When you lift the hood, you’ll see these items:
A.
Underhood Fuse
and Relay Center
B.
Remote Positive (+) Terminal
C.
Power Steering Fluid Reservoir
D.
Automatic Transaxle
Fluid Dipstick
E.
Brake Master Cylinder
F.
Windshield Washer
Fluid Reservoir
G. Battery
H.
Radiator Pressure Cap
I.
Engine Oil Fill Cap
J.
Engine Oil Dipstick
K.
Engine Air Cleaner/Filter
L.
Engine Coolant Reservoir
6-28
How to Check Power Steering Fluid
Turn the key off, let the engine compartment cool down,
wipe the cap and the top of the reservoir clean, then
unscrew the cap and wipe the dipstick with a clean rag.
Replace the cap and completely tighten it. Then remove
the cap again and look at the fluid level on the dipstick.
When the engine compartment is hot, the level should be
at the “H” mark. When it’s cold, the level should be at
the “C” mark. If the fluid is at the ADD mark, you
should add fluid.
What to Use
To determine what kind of fluid to use, see
“Recommended Fluids and Lubricants” in the Index.
Always use the proper fluid. Failure to use the proper
fluid can cause leaks and damage hoses and seals.
Windshield Washer Fluid
What to Use
When you need windshield washer fluid, be sure to read
the manufacturer’s instructions before use. If you will be
operating your vehicle in an area where the temperature
may fall below freezing, use a fluid that has sufficient
protection against freezing.
Adding Washer Fluid
The windshield washer fluid
reservoir is located on the
passenger’s side of the
engine compartment, near
the fuse and relay center.
See “Engine Compartment Overview” in the Index for
more information on location.
6-58
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring is protected by an internal circuit
breaker in the instrument panel fuse panel. An electrical
overload will cause the lamps to go on and off, or in
some cases to remain off. If this happens, have your
headlamp wiring checked right away.
Windshield Wipers
The windshield wiper motor is protected by an internal
circuit breaker and a fuse. If the motor overheats due to
heavy snow, etc., the wiper will stop until the motor
cools. If the overload is caused by some electrical
problem, be sure to get it fixed.
Power Windows and Other Power Options
Circuit breakers in the instrument panel fuse panel
protect the power windows and other power accessories.
When the current load is too heavy, the circuit breaker
opens and closes, protecting the circuit until the problem
is fixed.
6-59
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating.
If you ever have a problem on the road and don’t have
a spare fuse, you can borrow one that has the same
amperage or use one of the spare fuses in the underhood
fuse and relay center. Just pick some feature of your
vehicle that you can get along without
--
like the radio
or cigarette lighter
--
and use its fuse, if it is the right
amperage. Replace it as soon as you can.
There are two fuse blocks in your vehicle: the instrument
panel fuse block and the underhood fuse and relay center.
Floor Console Fuse and Relay Center
The floor console fuse and
relay center is located to the
right of the shift lever.
The fuses marked spare are available if a replacement
fuse is needed.
Pull the door open to access the fuse block.
6-60
Fuses
Usage
1
Fuse Puller
2
Steering Wheel Radio Controls
3
Power Door Locks
4
SPARE
5
SPARE
6
SPARE
7
SPARE
Fuses
Usage
8
SPARE
9
SPARE
10
Turn Signal and Hazard
Lamp Flashers
11
Power Seats
12
Electronic Level Control (ELC)
Compressor
13
Liftglass and Endgate
14
Rear Auxiliary Power Outlet
15
Electronic Level Control (ELC)
Compressor Relay and
Height Sensor
16
Heated Mirrors
17
Power Mirrors
18
Ignition 1 Module
19
Turn Signal Switch and
NSBU Switch
21
Rear Defogger
22
Air Bag Module
6-61
Fuses
Usage
24
Canister Vent Solenoid and
TCC Switch
25
HVAC Blower Motor
26
HVAC Mode and Temperature
Motors and Head
-
Up Display
28
Not Used
29
Windshield Wipers and Washer
30
Instrument Panel Cluster, BCM,
PASS
-
Key
R
III
31
Park Lock Ignition Key Solenoid
32
Not Used
34
Power Sunroof
35
Power Windows
36
Map Lamps, Courtesy Lamps and
Instrument Panel Lights
37
Radio
38
UQ3 Radio Amplifier
39
Head
-
Up Display
Fuses
Usage
40
Hazard Flashers
41
Instrument Panel Cluster, HVAC
Control, Security LED and
Remote Keyless Entry Module
42
PASS
-
Key
R
III
44
Body Control Module (BCM)
Relays
Usage
20
Rear Defogger Relay
23
IGN3 Relay
27
Accessory Relay
33
Retained Accessory Power Relay
Diode
43
Accessory Diode
6-62
Underhood Fuse and Relay Center
This fuse and relay center is located in the engine
compartment, on top of the windshield washer
fluid reservoir.
See “Engine Compartment Overview” in the Index for
more information on location.
The fuses marked spare are available if a replacement
fuse is needed.
To remove the cover, press the two tabs in and lift up the
cover. Remove the cover.
Mini Fuses
Usage
1
Fuel Pump
2
Air Conditioning Compressor Clutch
3
Horn
4
Engine Controls
-
Emissions
and Sensors
5
Power Control
Module (PCM)
-
Battery Power
6
Anti
-
Lock Brakes (ABS)
Control Module
7
Transaxle Solenoids
6-63
Mini Fuses
Usage
8
SPARE
9
ABS Solenoid Valves
10
Oxygen Sensors
-
Emissions Control
11
Fuel Injectors
12
SPARE
13
Engine Controls
14
Daytime Running Lamps (DRL)
15
Passenger’s Low
-
Beam Headlamp
16
SPARE
17
Driver’s Low
-
Beam Headlamp
18
Driver’s High
-
Beam Headlamp
19
Ignition Switch Battery Power
20
Parking Lamps
-
Front and Rear
21
Air Pump
-
Emissions Controls
22
SPARE
23
Passenger’s High
-
Beam Headlamp
24
SPARE
25
SPARE
26
Front Fog Lamps
Mini Fuses
Usage
27
Ignition Relay, Neutral Start
Switch, Powertrain Control
Module (PCM)
28
Body Control
Module
-
Battery Power
29
SPARE
30
All
-
Wheel Drive (AWD) Module
31
Cruise Control
32
Front Power
Outlets/Lights, OnStar
R
33
Automatic Transaxle Shift Lock
Control System
34
SPARE
J
-
Style Fuse
Usage
35
Starter Solenoid Battery Fuse
36
ABS Motor
37
SPARE
38
SPARE
39
Engine Cooling Fan
40
Engine Cooling Fan
6-64
J
-
Style Fuse
Usage
41
Main Battery Fuse for Retained
Accessory Power Relay and
Accessory Relay
42
Main Battery Fuse for
Heated Seats, Air
43
SPARE
44
SPARE
45
Main Battery Fuse for Power
Outlets, Level Control,
Power Seats and Mirrors and
Body Computer
46
SPARE
47
Main Battery Fuse for HVAC
Blower and Ignition 3 Relay
48
Main Battery Fuse for Ignition
Switch, Radio, Heads
-
Up Display,
Remote Keyless Entry (RKE),
Instrument Cluster, Air
Conditioning and Body Computer
Maxi Breaker
Usage
49
SPARE
Micro Relay
Usage
50
Horn
51
Fuel Pump
52
Air Conditioning Clutch
53
Daytime Running Lamps (DRL)
54
Low
-
Beam Headlamps
55
Parking Lamps
56
High
-
Beam Headlamps
57
Fog Lamps
Mini Relay
Usage
58
Starter Relay
59
Cooling Fan
60
Ignition 1 Relay
61
Cooling Fan
62
Cooling Fan
63
Air Pump