Pontiac Grand Prix - 2000 Fuse Box Diagram

Pontiac Grand Prix - 2000 Fuse Box Diagram

2-13
Entering Programming Mode
To program features, your vehicle must be in this
programming mode. Follow these steps:
1.
Turn the ignition key to LOCK or OFF.
2.
Remove the MALL PGM fuse from the instrument
panel fuse block. See “Fuses and Circuit Breakers”
in the Index.
3.
Turn the ignition key to ACCESSORY.
4.
Count the number of chimes you hear. You will hear
two to four chimes, depending on vehicle content.
See “Multifunction Alarm Locks and Lighting
Choices” earlier in this section.
You can now program your choices. After programming
a feature, you can exit the programming mode at
any time.
Exiting Programming Mode
To exit programming mode, turn the key from
ACCESSORY to OFF and put the MALL PGM fuse
back into the instrument panel fuse block.
Delayed Illumination and Exit Lighting
With delayed illumination, the interior lamps will stay
on for about 25 seconds after all doors are closed.
With exit lighting. the interior lamps will come on and
stay on for about 25 seconds whenever you remove the
key from the ignition.
To customize these features to your preference, see
“Programmable Modes.”
Programmable Modes
Your vehicle can be programmed to one of the
following modes.
Mode 1:
Both Features Off (The interior lamps will turn
on or off at the same instant that a door is opened
or closed.)
Mode 2:
Delayed Illumination Only (The interior lamps
will stay on for about 25 seconds after all the doors are
closed, or until you lock the doors.)
Mode 3:
Exit Lighting Only (The interior lamps will
come on whenever you remove the key from the ignition
and stay on for about 25 seconds, or until you lock
the doors.)
Mode 4:
Both Features On (This combines Modes 2
and 3.)
2-28
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse (see “Fuses and
Circuit Breakers” in the Index). If the engine still does
not start with the other key, your vehicle needs service.
If your vehicle does not start, the first key may be faulty.
See your dealer or a locksmith who can service the
PASS
-
Key III to have a new key made.
It is possible for the PASS
-
Key III decoder to learn the
transponder value of a new or replacement key. Up to
10 additional keys may be programmed for the vehicle.
This procedure is for learning additional keys only. If all
the currently programmed keys are lost or do not
operate, you must see your dealer or a locksmith who
can service PASS
-
Key III to have keys made and
programmed to the system.
See your dealer or a locksmith who can service
PASS
-
Key III to get a new key blank that is cut exactly
as the ignition key that operates the system.
To program the new key:
1.
Insert the black master ignition key in the ignition
and start the engine. If the engine will not start, see
your dealer for service.
2.
After the engine has started, turn the key to OFF, and
remove the key.
3.
Insert the key to be programmed and turn it to RUN
within 5 seconds of removing the original key.
4.
The SECURITY light will turn off once the key has
been programmed. It may not be apparent that the
SECURITY light went on due to how quickly the
key is programmed.
5.
Repeat Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the SECURITY light comes
on and stays on, you will be able to restart your engine if
you turn it off. Your PASS
-
Key III system, however, is
not working properly and must be serviced by your
dealer. Your vehicle is not protected by the PASS
-
Key
III system at this time.
If you lose or damage your PASS
-
Key III key, see your
dealer or a locksmith who can service PASS
-
Key III to
have a new key made.
2-48
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check for burned
-
out bulbs and then check
the fuse (see “Fuses and Circuit Breakers” in the Index).
A chime will sound if you leave the turn signal on for
more than 3/4 mile (1.2 km).
Headlamp High/Low Beam Changer
To change the headlamps
from low beam to high
beam, or high to low, pull
the multifunction lever
all the way toward you.
Then release it.
When the high beams are on, a light on the instrument
panel cluster also will be on. Please note that while you
are in high
-
beam mode, your fog lamps will not
be illuminated.
Flash-to-Pass Feature
When the headlamps are off, pull the lever toward you
to momentarily switch on the high beams (to signal that
you are going to pass). When you release the lever, they
will turn off and stay off.
Windshield Wipers
You control the windshield wipers by turning the band
marked WIPER on the turn signal/multifunction lever.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle. If you want more cycles, hold the
band on MIST longer.
For steady wiping at low speed, turn the band to LOW.
For high
-
speed wiping, turn the band further, to HIGH.
To stop the wipers, turn the band to OFF.
You can set the wiper speed for a long or short delay
between wipes. This can be very useful in light rain or
snow. Turn the band to choose the delay time. The
closer to LOW, the shorter the delay.
Be sure to clear ice and snow from the wiper blades
before using them. If they’re frozen to the windshield,
carefully loosen or thaw them. If the blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload the wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.
2-64
NOTICE:
Adding some electrical equipment to your vehicle
can damage it or keep other things from working
as they should. This wouldn’t be covered by your
warranty. Check with your dealer before adding
electrical equipment, and never use anything that
exceeds the fuse rating.
Auxiliary Power Connection
(Power Drop)
The vehicle is equipped with auxiliary power
connections. This feature can be used to power
aftermarket electrical equipment added to the vehicle.
The connections are located on the passenger’s side of
the vehicle, below the glove box.
OnStar
R
System (If Equipped)
OnStar is a vehicle communications service. The
following services are available through a subscription
with OnStar and are available 24 hours a day:
Emergency Services
D
Automatic Notification of Air Bag Deployment
D
Theft Notification and Stolen
-
Vehicle Tracking
D
Roadside Assistance with Location
D
Remote Diagnostics
D
OnStar MED
-
NET
D
Accident Assist
Convenience Services
D
Remote Door Unlock
D
Route Support
D
Concierge Services
D
Ride Assist
A complete user’s guide is provided with the OnStar
System. For more information contact OnStar
at 1
-
888
-
ONSTAR7.
2-67
The main components of the instrument panel are:
A.
Side Window Defogger Vents
B.
Fog Lamp Switch
C.
Multifunction Lever
D.
Instrument Panel Cluster
E.
Hazard Button
F.
Full Floating Horn
G.
Trip Computer/Driver Information Center (DIC)
H.
Instrument Panel Vents
I.
Interior Lamp Control
J.
Exterior Lamp Control
K.
Tilt Wheel Control
L.
Audio Steering Controls (If Equipped)
M. HUD Display Controls (If Equipped)
N.
Comfort Controls
O.
Ashtray and Cigarette Lighter
P.
Audio System
Q.
Glove Box
R.
Instrument Panel Fuse Block
2-81
Oil Warning Light
United States
Canada
If you have a problem with your oil pressure, this light
may stay on after you start your engine, or come on
when you are driving.
This indicates that oil is not going through your engine
quickly enough to keep it lubricated. The engine could
be low on oil or could have some other oil problem.
Have it fixed right away.
The oil light could also come on in two other situations:
D
When the ignition is on but the engine is not running,
the light will come on as a test to show you it’s
working. The light will go out when you turn the
ignition to RUN. If it doesn’t come on with the
ignition on, you may have a problem with the fuse or
bulb. Have it fixed right away.
D
If you make a hard stop, the light may come on for a
moment. This is normal.
CAUTION:
Don’t keep driving if the oil pressure is low.
If you do, your engine can become so hot that it
catches fire. You or others could be burned.
Check your oil as soon as possible and have your
vehicle serviced.
NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.
2-87
If You Can’t See the HUD Image When the Ignition
Is On
D
Is anything covering the HUD unit?
D
Is the HUD dimmer setting bright enough?
D
Is the HUD image adjusted to the proper height?
D
Still no HUD image? Check the fuse in the
instrument panel fuse block. See “Fuses and Circuit
Breakers” in the Index.
If the HUD Image Is Not Clear
D
Is the HUD image too bright?
D
Are the windshield and HUD lens clean?
The windshield is part of the HUD system. If you ever
have to have a new windshield, be sure to get one
designed for HUD. If you don’t, the HUD image may
look blurred and out of focus.
6-62
Electrical System
Add-On Electrical Equipment
NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
-
on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
-
Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring is protected by a circuit breaker in
the instrument panel fuse block. An electrical overload
will cause the lamps to go on and off, or in some cases
to remain off. If this happens, have your headlamp
system checked right away.
Windshield Wipers
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools.
If the overload is caused by some electrical problem,
have it fixed.
Power Windows and Other Power Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links in the wiring itself.
This greatly reduces the chance of fires caused by
electrical problems.
Look at the silver
-
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating. Spare fuses are located in the instrument
panel. See “Underhood Electrical Center” in the Index.
6-63
Instrument Panel Fuse Block
Some fuses are in a fuse block located inside of the
glove box behind a small bin on the right side. To open,
pull the cover out. The fuse block is inside. On the back
edge of this cover is a fuse puller and a fuse usage chart.
To use the fuse puller, place the wide end of the fuse
puller over the plastic end of the fuse. Squeeze the ends
over the fuse and pull it out.
To reinstall the bin, position the lower end and turn the
top into position. Press on the sides until it snaps
into place.
Circuit
Description
Breaker
HEADLAMP
Headlamps
SEAT
Power Seat, Power Lumbar
BLANK
Blank
PWR WDO
Power Windows
BLANK
Blank
6-64
Fuse
Description
BLANK
Blank
BLANK
Blank
MALL PGM
Mall Module
--
Program
MALL
Mall Module
WIPER
Wipers
STR WHL
ILLUM
Steering Wheel Illumination
BLANK
Blank
STR WHL
CTRL
Steering Wheel Control
SUNROOF
Sunroof
RADIO
Radio, Antenna
BLANK
Blank
RADIO AMP
Bose Amplifier
PWR LOCK
Mall Module
--
Power Locks
HSEAT/LUM
Heated Seats, Power Lumbar
Fuse
Description
R DEFOG
Rear Defog
PASSKEY III
PASS
-
Key
R
III Security System
RAP
Retained Accessory Power
HAZARD
Hazard Flashers
PWR MIR
Power Mirrors
HVAC HI
HVAC Blower
--
Hi
CIG LTR
Cigarette Lighter, ALDL, Floor
Console Accessory Outlet
INT LAMP
Mall Module
--
Interior lamps
STOP LAMP
Stoplamp
AUX/CNSL
Accessory Power,
Overhead Console
CD CHG
CD Changer
ECM
Electronic Control Module
CRUISE
Cruise Control
6-65
Fuse
Description
I/P
-
IGN
Chime/Mall Module, Cluster,
Trip Computer, Head
-
Up Display,
Automatic Transaxle Shift
Lock Control
SIR
Supplemental Inflatable Restraint
(Air Bag)
TURN
Turn Signal
BLANK
Blank
BLANK
Blank
BLANK
Blank
BLANK
Blank
BTSI
Automatic Transaxle Shift
Lock Control
BLANK
Blank
Fuse
Description
BLANK
Blank
BLANK
Blank
HVAC CTRL
Blower Control, HVAC
DIC/HVAC
Rear Defog, HVAC, Driver
Information Center, Daytime
Running Lamps, Heated Seats
BLANK
Blank
BLANK
Blank
PWR DROP
Power Drop Ignition
CANISTER
VENT
Canister Vent Solenoid
DRL
Daytime Running Lamps
6-66
Underhood Electrical
Center -- Passenger’s Side
Some fuses are in a fuse
block on the passenger’s
side of the engine
compartment. Pull off the
cover labeled FUSES to
expose the fuses.
Fuse
Description
1
Cooling Fan 2
2
Spare
3
Headlamps
4
Battery Main 2
5
Ignition Main 1
6
Cooling Fan 1
7
Battery Main 1
8
Ignition Main 2
18
Fuel Injections
6-67
Fuse
Description
19
Spare
20
Spare
21
Mass Air Flow (MAF), Heated Sensors,
Canister Purge, Boost Solenoid
22
Spare
23
Spare
24
Spare
25
Ignition Module
26
Spare
27
Trunk Release, Back
-
Up Lamps
28
AC Clutch, ABS Ignition
29
Remote Keyless Entry, Theft
-
Deterrent,
Shock Sensor, Trip Computer, HVAC
Module, Security LED
30
Alt Sense
31
Torque Converter Clutch (TCC)
32
Fuel Pump
33
Electronic Control Module/Powertrain
Control Module
34
Spare
Fuse
Description
35
Fog Lamps
36
Horn
37
Chime/Mall Module, Taillamps,
Parking Lamps, Sidemarker Lamps,
Dimmable Lamps
38
Spare Fuse
39
Air Pump
40
Spare
Diode
Description
Air Conditioning Clutch Diode
Relay
Description
9
Cooling Fan
10
Cooling Fan 2
11
Ignition Main
12
Cooling Fan 1
13
Air Conditioning Clutch
14
Fuel Pump
15
Fuel Pump Speed Cont
16
Horn
17
Fog Lamp