Entering Programming Mode
To program features, your vehicle must be in this
programming mode. Follow these steps:
Turn the ignition key to LOCK or OFF.
Remove the MALL PGM fuse from the instrument
panel fuse block. See “Fuses and Circuit Breakers”
in the Index.
Turn the ignition key to ACCESSORY.
Count the number of chimes you hear. You will hear
two to four chimes, depending on vehicle features.
Refer to the chart shown previously for available
You can now program your choices. After programming a
feature, you can exit the programming mode at anytime.
Exiting Programming Mode
To exit programming mode, turn the key from
ACCESSORY to OFF and put the MALL PGM fuse
back into the instrument panel fuse block.
Delayed Illumination and Exit Lighting
With Delayed Illumination, the interior lamps will stay
on for about 25 seconds after all doors are closed.
With Exit Lighting. the interior lamps will come on and
stay on for about 25 seconds whenever you remove the
key from the ignition.
To customize these features to your preference,
see “Programmable Modes” following.
Your vehicle can be programmed to one of the
Both Features Off (The interior lamps will turn on
or off at the same instant that a door is opened or closed.)
Delayed Illumination Only (The interior lamps
will stay on for about 25 seconds after all the doors are
closed, or until you lock the doors.)
Exit Lighting Only (The interior lamps will
come on whenever you remove the key from the ignition
and stay on for about 25 seconds, or until you lock
Both Features On (This combines modes 2 and 3.)
Your vehicle comes with this feature set in mode 4.
Turn and Lane Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return automatically.
An arrow on the instrument
panel will flash in the
direction of the turn or
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or a lane change, if the arrow
flashes faster than normal, a signal bulb may be burned
out and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check for burned
out bulbs and then check
the fuse (see “Fuses and Circuit Breakers” in the Index).
A chime will sound if you leave the turn signal on for
more than 3/4 mile (1.2 km).
Headlamp High/Low Beam Changer
To change the headlamps
from low beam to high
beam, or high to low, pull
the multifunction lever all
the way toward you. Then
When the high beams are on, a light on the instrument
panel also will be on.
When the headlamps are off, pull the lever toward you
to momentarily switch on the high beams (to signal that
you are going to pass). When you release the lever, they
will turn off.
The main components of the instrument panel are:
Side Window Defogger Vents
Fog Lamp Switch
Instrument Panel Cluster
Emergency Flasher Button
Full Floating Horn
Column Shift Lever (If Equipped)
Trip Computer/Driver Information Center (DIC)
Instrument Panel Vents
Interior Lamp Control
Exterior Lamp Control
Tilt Wheel Control
M. Audio Steering Controls (If Equipped)
HUD Display Controls (If Equipped)
Ashtray and Cigarette Lighter
Instrument Panel Fuse Block
Oil Warning Light
If you have a problem with
your oil pressure, this light
may stay on after you start
your engine, or come on
when you are driving.
This indicates that oil is not going through your engine
quickly enough to keep it lubricated. The engine could
be low on oil or could have some other oil problem.
Have it fixed right away.
The oil light could also come on in two other situations:
When the ignition is on but the engine is not running,
the light will come on as a test to show you it is
working, but the light will go out when you turn the
ignition to START. If it doesn’t come on with the
ignition on, you may have a problem with the fuse or
bulb. Have it fixed right away.
If you make a hard stop, the light may come on for a
moment. This is normal.
Don’t keep driving if the oil pressure is low. If
you do, your engine can become so hot that it
catches fire. You or others could be burned.
Check your oil as soon as possible and have your
Damage to your engine from neglected oil
problems can be costly and is not covered by
If You Can’t See the HUD Image When
the Ignition Is On
Is anything covering the HUD unit?
Is the HUD dimmer setting bright enough?
Is the HUD image adjusted to the proper height?
Still no HUD image? Check the fuse in the
instrument panel fuse block. See “Fuses and Circuit
Breakers” in the Index.
If the HUD Image Is Not Clear
Is the HUD image too bright?
Are the windshield and HUD lens clean?
The windshield is part of the HUD system. If you ever
have to have a new windshield, be sure to get one
designed for HUD. If you don’t, the HUD image may
look blurred and out of focus.
Power Drop Feature
The vehicle is equipped with auxiliary power leads.
These leads can be used to power aftermarket electrical
equipment added to the vehicle. They are located on the
passenger’s side of the vehicle, below the glove box. For
additional information on accessing these leads and
electrical hookup, please refer to the service manual.
Add-On Electrical Equipment
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add
on electrical equipment
can keep other components from working as
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag
Equipped Vehicle” in the Index.
The headlamp wiring is protected by a circuit breaker in
the instrument panel fuse block. An electrical overload
will cause the lamps to go on and off, or in some cases
to remain off. If this happens, have your headlamp
system checked right away.
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools. If
the overload is caused by some electrical problem, have
Power Windows and Other Power Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and closes,
protecting the circuit until the problem is fixed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links in the wiring itself. This
greatly reduces the chance of fires caused by
Look at the silver
colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating. Spare fuses are located in the instrument
panel. See “Underhood Electrical Center” in the Index.
Instrument Panel Fuse Block
Some fuses are in a fuse block located inside of the
glove box behind a small bin on the right side. To open,
pull the cover out. The fuse block is inside. On the back
edge of this cover is a fuse puller and a fuse usage chart.
To use the fuse puller, place the wide end of the fuse
puller over the plastic end of the fuse. Squeeze the ends
over the fuse and pull it out.
To reinstall the bin, position the lower end and turn the
top into position. Press on the sides until it snaps
Power Seat, Power Lumbar
Steering Wheel Illumination
Steering Wheel Control
Heated Seats, Power Lumbar
Retained Accessory Power
Cigarette Lighter, ALDL, Floor
Console Auxiliary Outlet
Auxiliary Power, Overhead
Electronic Control Module
Chime/Mall Module, Cluster, Trip
Transaxle Shift Interlock
Supplemental Inflatable Restraint
Blower Control, HVAC
Rear Defog, HVAC, Driver
Information Center, Daytime
Running Lamps, Heated Seats
Power Drop Ignition
Canister Vent Solenoid
Daytime Running Lamps
Center -- Passenger’s Side
Some fuses are in a fuse
block on the passenger’s
side of the engine
compartment. Pull off the
cover labeled FUSES to
expose the fuses.
Cooling Fan 2
Battery Main 2
Ignition Main 1
Cooling Fan 1
Battery Main 1
Ignition Main 2
Mass Air Flow (MAF), Heated
Sensors, Canister Purge, Boost
Trunk Release, Back
AC Clutch, ABS Ignition
Radio, Remote Keyless Entry,
Deterrent, Shock Sensor,
Trip Computer, HVAC Module,
Lock Brake System Module,
Torque Converter Clutch (TCC)
Chime/Mall Module, Taillamps,
Parking Lamps, Sidemarker
Lamps, Dimmable Lamps
Air Conditioning Clutch Diode
Cooling Fan 2
Cooling Fan 1
Air Conditioning Clutch
Fuel Pump Speed Cont