Oldsmobile Aurora - 1998 Fuse Box Diagram

Oldsmobile Aurora - 1998 Fuse Box Diagram

If a
door
or
the trunk is opened without the key or
remote lock
control transmitter, the alarm will go
off.
It will also
gooff if
the
trunk lock or
door locks are
damaged. Your vehicle’s lamps will flash and the horn
will sound for several minutes, then will go off to
save
battery power.
Remember, the
theft-deterrent system won’t activate if
you lock the
doors with a key or manual door
lock. It
only activates if
you use the power door lock switch
or
remote lock
controltransmitter. You should also
remember that you can start your vehicle with the
correct ignition key
if
the alarm has been set off, but this
does not shut
off
the
alarm.
Here’s how to avoid setting off the alarm by accident:
If
you don’t want to
activate
the theft-deterrent
system, lock the door either using a key, or
the
manual door lock switch.
Always unlock a
door with a key, or
use the remote
lock
control
system. Unlocking a
door any other way
will set off the
alarm.
I f
you
set
off
the
alarm
by
accident, unlock
any
door
with
your
key.
You can also turn off the alarm by pressing UNLOCK
on the remote lock control transmitter. The alarm won’t
stop if
you
try
to unlock a door any other way.
Testing
the
Alarm
The alarm can be tested by following
these
steps:
1.
From inside the vehicle, roll down the driver’s
window and open the driver’s door.
2.
Activate the system by locking the doors with the
power door lock switch while the door is open,
or
with the remote lock control transmitter.
3.
Get out of the car, close
the door and wait for the
SE.CURITY light
to
go
out.
4.
Then reach in through the window, unlock the door
with the manual door lock and open the door. This
should set off the
alarm.
If
the alarm does not sound when it
should, but the
vehicle’s lamps flash, check to
see if the horn works.
The horn fuse may
be blown.
To
replace
the
fuse,
see “Fuses and Circuit Breakers’’
in the Index.
If
the alarm does not sound,
or
the vehicle’s lamps
do not flash, the vehicle should be serviced by an
authorized
service center.
2-17
I1
Your vehicle is equipped
with the PASS-Key I1
(Personalized Automotive
Security System)
theft-deterrent system.
PASS-Key I1 is a passive
theft-deterrent system.
It works when you insert
or remove the key from
the ignition.
PASS-Key
I1
uses a resistor pellet in the ignition key
that matches a decoder in your vehicle.
When the PASS-Key
I1
system senses that someone
is
using the wrong key, it
shuts down the vehicle’s starter
and fuel systems. For about three minutes, the starter
won’t work and fuel won’t go to the e,ngine.
If someone
tries to start your vehicle again or uses another key
during
this
time, the vehicle will not start.
This
discourages someone from randomly trying different
keys with different resistor pellets in an attempt to
make a match.
The ignition key must be clean and dry before it’s
inserted in the ignition or the engine may not start. If
the engine
does not start and the SECURITY light
is
on or you get
the CLEAN KEY...WAIT
3
MINUTES
message on the DIC, the key may be dirty or wet.
Turn
the ignition off.
Clean and dry the key.
Wait about
three minutes and try
again. The SECURITY light may remain on during
this
time. If
the
starter still won’t work, and the key appears
to be clean and dry, wait about three minutes and try
another ignition key.
At this time, you may also want to
check the
fuses (see “Fuses and Circuit Breakers” in the
Index). If the starter won’t work with the other key, your
vehicle needs service. If your vehicle does
start,
the first
ignition key may be faulty. See your retailer
or
a
locksmith who can service the PASS-Key
11.
If
you accidentally use a key that has a damaged
or missing resistor pellet, the starter won’t work.
The SECURITY light will flash and the CLEAN
KEY...
WAIT
3
MINUTES message will appear. But
you don’t have
to
wait three minutes before trying
another ignition key.
2-18
Turn and
Lane
Change
Signals
The turn signal
has
two upward (for right) and two
downward (for left) positions.
These positions allow
you to
signal
a
turn or
a
lane
change.
To
signal
a turn, move the lever
all
the way
up or
down. When the turn is finished, the lever will
return automatically.
I
1
An arrow on the
instrument
panel will flash in the
direction of the
turn
or
lane
change.
To
signal
a
lane
change,
just
raise
or
lower the lever
until the arrow starts
to
flash.
Hold
it
there until you
complete your lane changp The
lever
will
return
bv
itself when you release
it.
As you signal
a
turn or a
lane
change,
if the
arrows
don’t flash but just stay on, a signal bulb may
be burned
out and other
drivers won’t see your turn signal.
If a
bulb
is
burned out,
replace
it
to
help avoid
an accident.
If the arrows
don’t
go
on
at all when you signal a
turn,
check the fuse (see “Fuses and Circuit Breakers” in the
Index) and for burned-out bulbs.
Turn
Signal
On
Chime
If your turn signal is left on for more than
3/4
of a mile
(1.2 km),
a
chime
will sound and the DIC will display
the TURN
SIGNAL
ON?
reminder message.
To
turn
off the
chime,move the turn signal lever
to
the
off
position.
To
turn off the DIC message, press any button
on the DIC.
Have you recently changed brands of fuel?
If
so,
be sure
to
fuel your vehicle with quality
fuel
(see
“Fuel” in the Index). Poor fuel quality will cause your
engine not to run as efficiently as
designed.You may
notice
this as stalling
after start-up, stalling when you
put
the
vehicle
into
gear, misfiring, hesitation on
acceleration
or
stumbling on acceleration. (These
conditions may go away once the
engine
is warmed up.)
This will be detected by the system and cause
the
light
to turn
on.
If
you experience
one
or more of these
conditions,
change the
fuel brand you use.
It will require at least
one
full tank of the
proper
fuel
to
turn the light off.
If none
of
the above steps have made the light turn
off,
have your retailer or
qualified
service
center
check the
vehicle. Your retailer has the
proper
test
equipment and
diagnostic
tools
to
fix
any mechanical or
electrical
problems that may have developed.
Oil
Pressure
Warning
Light
If you have a problem with
your oil,
this
light may
stay on after you start your
engine,
or come on when
OIL
you
are
driving.
A warning chime and the message
LOW
OIL
PRESSURE may also
come
on.
These
indicate
that
oil
is
not going through your engine
quickly enough to keep it
cool.
The
engine
could
be
low
on
oil,
or
could
have
some other
oil
problem.
Have
it
fixed right away.
The oil light could also come on briefly when the
ignition is on but
the
engine
is
not running. The
light
will come on as a test to show
you
it
is
working,
but
the
light will go
out when you turn the ignition to START.
If
it doesn’t come on with the ignition on, you
may have a
problem with the fuse
or
bulb. Have it fixed right away.
Electrical
System
Add-on Electrical EquiD:
t
NOTICE:
~-
Don’t
add
anything
electrical
to
your
vehicle
unless
you
check
with
your
retailer
first.
Some
electrical
equipment
can
damage
your
vehicle
and
the
damage
wouldn’t
be
covered
by
your
warranty.
Some
add-on
electrical
equipment
can
keep
other
components
from
working
as
they
should.
Headlamp
Wiring
The headlamp wiring is protected by a
circuit breaker
in the wiring harness.
An
electrical overload will cause
the lamps to go on and
off,
or
in
some
cases to remain
off.
If
this happens, have your headlamp system checked
right away.
Windshield
Wiper
Fuses
The windshield wiper motor is protected by
an internal
circuit breaker and a
fuse
in
the
fuse panel on the other
side of the instrument panel.
If
the motor overheats due
to heavy
snow, etc., the wiper will
stop
until
the motor
cools.
If
the overload is caused by some
electrical
problem, have it fixed.
Your vehicle has
an air bag system. Before attempting to
add anythng electrical
to
your vehicle, see “Servicing
Your
Air
Bag-Equipped Vehicle”
in
the
Index.
Power
Windows
and
Other
Power
Options
Circuit breakers in the
fuse panel protect the power
windows and other power accessories. When the
current
load
is
too
heavy,
the circuit breaker opens
and closes,
protecting the circuit until the problem is fixed.
6-60
Maxifuse@/Relay
Center
It’s easy
to
check
the
fuses
in
this
underhood relay
center. There
are
two locking
arms
on either
side of the
base of the cover. Reach
downand unsnap each one by
pulling
the cover toward you,
then pushing it away
while pulling up. Remove
the cover. The
inside of the
cover has
a
chart
that
explains
the
features
and controls
governed by each
fuse and relay.
Fuses
and
Circuit
Breakers
The wiring circuits
in your vehicle
are protected from
short
circuits by a combination
of
fuses and circuit
breakers.
This greatly reduces
the
chance
of
damage
caused by electrical
problems.
Look at the silver-colored band inside
the
fuse.
If
the band is broken or
melted,
replace
the
fuse.
Be
sure you replace
a
bad
fuse
with a new one of the
correct amp rating.
1wo
spare
fuses
are located below the
fuse puller.
You’ll
also
find
spare
fuses
in
the
slots labeled “Spare’’ in the
following
charts.
There
are
three main fuse panels: the instrument panel
fuse block and two (driver’s side and passenger’s side)
rear compartment fuse blocks.
6-61
Instrument
Panel
Fuse
Block
This
fuse block is located on the
left
side
of
the
instrument panel.
To
open it, push the latch to the left,
then pull, and the door will open.
You’ll find
a
fuse
puller clipped to the inside
of
the
cover. Place the wide end
of
the fuse puller over the
plastic end
of
the fuse. Squeeze the ends
over
the
fuse
and pull
it out.
To
close
the
fuse door, press the door
closed and it
will
latch.
/
INSTRUMENT
PANEL
11112113114
FUSE
BLOCK
CHIME
PCM
PWR
CNTRL
LIGHTS
I
RELAY
LAMPS
PACK
MTR
mmJ2?CRANK
/12
f
iHVhC
BLOWER
Fuse
Usage
1
Supplemental
Inflatable
Restraint
(Air
Bag)
2
3
4
5
6
7
Injectors
Anti-Lock
Brake
System
Left
Exterior
Lamps
Turn Signal Lamps
Injectors
Climate
Controls
8
Right
Exterior
Lamps
9
Chime
(Ignition
l),
Memory Set
10
Powertrain
Control
Module,
VATS
11
Auxiliary
Power
12
13
14
15
16
Interior
Lamps
Shift Solenoids
Linear
EGR
Cruise
Control
Perimeter
Lights
Fuse
17
18
19
20
21
22
23
24
25
26
27
28
Usage
Driver
Information
Center
Converter
Oxygen
Sensors
Radio
Open
Climate
Control
Relay
Fog
Lamps
Windshield
Wipers
Flat Pack
Motor
TMNSS
Cigarette
Lighter
Crank,
Air
Bag
Module
Climate
Control
Blower
6-63
Removing
the
Rear
Seat
Cushion
To
access the battery and rear compartment fuse panels,
the rear seat cushion must be removed.
This procedure is
somewhat difficult. You may wish to have your retailer
do this for you.
NOTICE:
The battery and main fuse
boxes are located
under the rear seat cushion.
The
battery’s
ground terminal and some
relay
wires
are
exposed.
To
help
avoid damage
to
the battery
and wires,
be careful when
removing or
reinstalling the seat cushion.
Do
not remove
covers from covered parts.
Do
not store anything
under the seat, as objects could
touch
exposed
wires and cause a short.
To
Remove the Rear Seat Cushion
1.
Pull up on the front
of
the cushion to release the
front hooks.
2.
Pull the cushion
up
and
out
toward the front of
To
Reinstall
the
Rear Seat Cushion
the vehicle.
6-64
A
safety
belt that isn’t properly routed through
the seat cushion or is
twisted
won’t
provide
the
protection needed in a crash.
If
the safety
belt
hasn’t
been routed through the seat cushion at
all, it won’t
be there to work for the next
passenger.
The
person sitting in
that position
could
be
badly
injured. After reinstalling the seat
cushion,
always
check
to be sure
that
the
safety
belts are properly routed and
are not
twisted.
1.
2.
3.
Buckle
the
center
passenger
position safety belt, and
then route the safety belts
through the proper slots in
the
seat
cushion. Don’t let
the safety belt get
twisted.
Slide
the
rear
of the cushion up and
under the
seatback
so
the rear
locating
guides hook into
the
wire
loops
on
the back frame.
With the seat
cushion
lowered, push rearward and
then press down
onthe seat cushion until the spring
locks
on both ends
engage.
4.
Check to make
sure
the safety belts
are properly
routed and that
no
portion of any safety belt is
trapped under
the
seat.
Also
make
sure
the seat
cushion
is
secured.
Rear Compartment Fuse
Blocks
Once the seat is removed,
you’ll find
two
fuse
panels
on the driver’s
sideof the
battery. Each
is protected by
a plastic box with four tabs.
Pull up on all four
tabs at
the same time to loosen
them and pull off the box.
Of these
twopanels, the cover on the passenger’s side
fuse panel has an extra plastic cap
attachment. You’ll
need
to
slide this out
of
the
grooves which hold it there
before removing the rest of the box.
To
replace
the
covers,
line
the
four
tabs up and simply
snap
them back into place.
The
extra plastic cap
attachment slides back into
place.
6-65
REAR
COMPARTMENT
DRIVER
SIDE
FUSE
BLOCK
1
3
1 1
FPMP
1
I
DDooR
UNLOCK
F
E
D
B
L2
DBFG
-
RR
# 1
A
ACSRY
DAP
OPEN
Fuse
1
2
3
4
5
6
7-
10
11
12
13
14
15
16
17-22
23
24
Usage
Open
Electronic Level Control Relay
Trunk Release Relay
Open
Fuel
Pump
Relay
Driver Door Unlock Relay
Open
Rear Defogger
Relay (Upper Zone)
Rear
DefoggerRelay (Lower
Zone)
Open
Spare
Spare
Spare
Open
Direct Accessory Power
--
Accessory
Relay
Open
6-66
REAR
COMPARTMENT
PASSENGER
SIDE
FUSE
BLOCK
1s
PWR
SI'
i
I6
HDLP
1
18
PCM!
VATS
I
IGN
3
20
ItiN
I
Fuse
172
3
4
596
7
899
10
11
12,
13
14
15
16
17
18
19
20
21
Usage
Spare
Open
Breaker
--
Power Window, Sunroof
Spare
Open
Spare
Open
Breaker
--
Power
Seat
Spare
Open
Power
Seat
Breaker
--
Headlamps
HVAC
Blower Motor
Powertrain Control Module,
Ignition
3
Ignition
1
Rear
Defogger
6-67
Fuse
22
23
24
25
26
27
28
29
30
31
32
Usage
Trunk
and
Fuel
Door
Releases
and
Trunk
Pull
Down
Electronic
Level
Control
Heated
Seat,
Instrument
Panel
Exterior
Lamps
Stereo
(Option)
Power
Door
Locks
Interior
Lam]
Hazard
Lamps,xoplamps
Parking
Lamps
Heated
Outside
Mirror
Open
Fuse
Usage
33
Fuel
Door
Release
34
Cooling
Fan
Relay
35
Battery
Thermistor
36 Instrument Panel
--
Power Antenna, Remote
CD
Changer,
Radio
Chassis
Instrument
Panel
--
Remote
Accessory
Power
Module,
Oil
Level
Indicator,
ALDL
37
38
39
40
41
42
Heated
Seats
Fuel
Pump
Open
Rear
Defog
2
Rear
Defog
1
Engine
Compartment
Fuse
Block
ENGINE
COMPARTMENT
FUSE
BLOCK
I
HORN
I 1
I I
FOG LAMP
2
I
I
I I
I
I
I
COOLING
FAN
#2
COOLING
FAN
# 3
Fuse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Usage
Air
Conditioning
Center
Open
Open
Horn
Open
Fog
Lamp
2
Cooling Fan
#2
Cooling Fan
#3
Cooling
Fan
ABS
Main
ABS
Pump Motor
Fog
Lamp
Horn
Open
6-69