Cadillac XT5 - 2017 Fuse Box Diagram

Cadillac XT5 - 2017 Fuse Box Diagram

Instruments and Controls
115
Auto Set
When on, the time and date will
automatically update.
To set auto set:
1.
Touch the SETTINGS screen
button, then touch Time
and Date.
2.
Touch Set Time or Set Date.
3.
Touch Auto Set, then select
On-Cell Network or Off-Manual
to manually set the time
and date.
4.
Touch
[
Back to go back to the
previous menu.
If auto set is on, the time displayed
on the clock may not update
immediately when driving into a new
time zone.
Clock Display
When on, the digital clock will
display on the infotainment screen.
To set the clock display:
1.
Touch the SETTINGS screen
button, then touch Time
and Date.
2.
Touch Clock Display, then
select Off or On.
3.
Touch
[
Back to go back to the
previous menu.
Power Outlets
The accessory power outlet can be
used to plug in electrical equipment,
such as a cell phone or MP3 player.
The vehicle has two accessory
power outlets, one on the lower
center floor console and one in the
rear cargo area.
Lift the cover to access the
accessory power outlet.
Certain accessory power plugs may
not be compatible with the
accessory power outlet and could
overload vehicle or adapter fuses.
If a problem is experienced, see
your dealer.
When adding electrical equipment,
be sure to follow the proper
installation instructions included with
the equipment. See
Add-On
Electrical Equipment
0
252
.
Caution
Hanging heavy equipment from
the power outlet can cause
damage not covered by the
vehicle warranty. The power
outlets are designed for
accessory power plugs only, such
as cell phone charge cords.
Always unplug electrical equipment
when not in use and do not plug in
equipment that exceeds the
maximum 15 amps rating.
Instruments and Controls
117
remove the phone from the
pad, turn 180 degrees and wait
three seconds before placing/
aligning the phone on the pad
again.
Cigarette Lighter
If equipped with a cigarette lighter, it
is located in the center console near
the cupholders. Press on the access
door to open it and use the lighter.
To use the cigarette lighter, push it
in all the way, and let go. When it is
ready, it will pop back out by itself.
Caution
Holding a cigarette lighter in while
it is heating does not let the
lighter back away from the
heating element when it is hot.
Damage from overheating can
occur to the lighter or heating
element, or a fuse could be
blown. Do not hold a cigarette
lighter in while it is heating.
Ashtrays
If equipped, the ashtray is in the
center console cupholder.
Caution
If papers, pins, or other
flammable items are put in the
ashtray, hot cigarettes or other
smoking materials could ignite
them and possibly damage the
vehicle. Never put flammable
items in the ashtray.
To remove the ashtray, pull it from
the cupholder. Push it back down to
be sure it is secure.
Warning Lights,
Gauges, and
Indicators
Warning lights and gauges can
signal that something is wrong
before it becomes serious enough
to cause an expensive repair or
replacement. Paying attention to the
warning lights and gauges could
prevent injury.
Some warning lights come on briefly
when the engine is started to
indicate they are working. When
one of the warning lights comes on
and stays on while driving, or when
one of the gauges shows there may
be a problem, check the section that
explains what to do. Waiting to do
repairs can be costly and even
dangerous.
Lighting
169
|
:
Touch
|
on the center stack
to make the front and rear turn
signal lamps flash on and off. Touch
again to turn the flashers off.
The hazard warning flashers turn on
automatically if the airbags deploy.
Turn and Lane-Change
Signals
Move the lever all the way up or
down to signal a turn.
An arrow on the instrument cluster
flashes in the direction of the turn or
lane change.
Raise or lower the lever until the
arrow starts to flash to signal a lane
change. Hold it there until the lane
change is completed. If the lever is
briefly pressed and released, the
turn signal flashes three times.
The turn and lane-change signal
can be turned off manually by
moving the lever back to its original
position.
If after signaling a turn or lane
change, the arrow flashes rapidly or
does not come on, a signal bulb
may be burned out.
Replace any burned out bulbs. If a
bulb is not burned out, check the
fuse. See
Fuses and Circuit
Breakers
0
275
.
Cornering Lamps
If equipped with cornering lamps,
they automatically come on when all
of the following occur:
.
The low-beam headlamps
are on.
.
The turn signals are activated or
the steering wheel is at a
calibrated angle.
.
The vehicle speed is below the
calibrated speed.
Interior Lighting
Instrument Panel
Illumination Control
The brightness of the instrument
panel lighting and steering wheel
controls can be adjusted.
D
:
Move the thumbwheel up or
down to brighten or dim the lights.
The brightness of the displays
automatically adjust based on
outdoor lighting. The instrument
panel illumination control will set the
lowest level to which the display will
be automatically adjusted.
250
Driving and Operating
To reinstall the hitch cover:
1.
Hold the cover at a 45 degree
angle to the vehicle and push
the upper tabs in the hitch
cover into the slots in the
fascia.
2.
Move the bottom of the cover
forward until the lower tabs line
up with the lower fascia slots.
3.
Snap the hitch cover into place
by pushing the upper corners
forward.
4.
Turn the fasteners on the lower
tabs 90 degrees clockwise to
lock the cover in place.
Safety Chains
Always attach chains between the
vehicle and the trailer. Cross the
safety chains under the tongue of
the trailer to help prevent the tongue
from contacting the road if it
becomes separated from the hitch.
Always leave just enough slack so
the rig can turn. Never allow safety
chains to drag on the ground.
Trailer Brakes
A loaded trailer that weighs more
than 454 kg (1,000 lb) needs to have
its own brake system that is
adequate for the weight of the
trailer. Be sure to read and follow
the instructions for the trailer brakes
so they are installed, adjusted, and
maintained properly.
Because the vehicle has antilock
brakes, do not tap into the vehicle's
brake system. If you do, both brake
systems will not work well, or at all.
Trailer Wiring Harness
Basic Trailer Wiring
The trailer wiring harness, with a
seven-pin connector, is located at
the rear of the vehicle and is tied to
the vehicle's frame. The harness
connector can be plugged into a
seven-pin universal heavy-duty
trailer connector available through
your dealer.
The seven-wire harness contains
the following trailer circuits:
.
Yellow/Gray: Stop/Turn
Signal Left
.
Green/Violet: Stop/Turn Signal
Right
.
Gray/Brown: Parking Lamps
.
White/Green: Back-up Lamps
.
Red/Green: Battery Feed
.
Black: Ground
.
Blue: Electric Brakes*
*The fuse for this circuit is installed
in the underhood electrical center,
but the wires are not connected.
They should be connected by your
dealer or a qualified service center.
If the back-up lamp circuit is not
functional, contact your dealer.
Electric Trailer Brake Control
Wiring Provisions
These wiring provisions for an
electric trailer brake controller are
included with the vehicle as part of
the trailer wiring package. The
instrument panel contains blunt cut
wires above the parking brake
assembly for the electric trailer
brake controller. The harness
contains the following wires:
.
Blue:
To Trailer
258
Vehicle Care
1.
Engine Air Cleaner/Filter
0
261
.
2.
Engine Oil Fill Cap. See
Engine Oil
0
258
.
3.
Engine Oil Dipstick. See
Engine Oil
0
258
.
4.
Engine Cooling Fan (Out of
View). See
Cooling
System
0
262
.
5.
Brake Fluid Reservoir. See
Brake Fluid
0
268
.
6.
Battery - North America
0
269
.
7.
Engine Coolant Surge Tank
and Pressure Cap. See
Cooling System
0
262
.
8.
Positive (+) Battery Terminal
(Under Cover). See
Jump
Starting - North America
0
317
.
9.
Windshield Washer Fluid
Reservoir. See
Washer
Fluid
0
267
.
10.
Engine Compartment Fuse
Block
0
275
.
11.
Remote Negative (-) Battery
Terminal. See
Jump Starting -
North America
0
317
.
Engine Oil
To ensure proper engine
performance and long life, careful
attention must be paid to engine oil.
Following these simple, but
important steps will help protect
your investment:
.
Use engine oil approved to the
proper specification and of the
proper viscosity grade. See
Selecting the Right Engine Oil
in this section.
.
Check the engine oil level
regularly and maintain the
proper oil level. See
Checking
Engine Oil
and
When to Add
Engine Oil
in this section.
.
Change the engine oil at the
appropriate time. See
Engine Oil
Life System
0
260
.
.
Always dispose of engine oil
properly. See
What to Do with
Used Oil
in this section.
Checking Engine Oil
It is a good idea to check the engine
oil level at each fuel fill. In order to
get an accurate reading, the vehicle
must be on level ground. The
engine oil dipstick handle is a loop.
See
Engine Compartment Overview
0
257
for the location of the engine
oil dipstick.
1.
If the engine has been running
recently, turn off the engine and
allow several minutes for the oil
to drain back into the oil pan.
Checking the oil level too soon
after engine shutoff will not
provide an accurate oil level
reading.
{
Warning
The engine oil dipstick handle
may be hot; it could burn you.
Use a towel or glove to touch the
dipstick handle.
2.
Pull out the dipstick and wipe it
with a clean paper towel or
cloth, then push it back in all
the way. Remove it again,
keeping the tip down, and
check the level.
274
Vehicle Care
4.
Disconnect the wiring harness
connector from the bulb.
5.
Install the new bulb in the
headlamp assembly by turning
clockwise.
6.
Reconnect the wiring harness
connector.
7.
Install the headlamp bulb
access cover.
Turn Signal Lamp
1.
Open the hood. See
Hood
0
256
.
2.
Remove the turn signal lamp
bulb socket from the headlamp
assembly by turning
counterclockwise.
3.
Remove the bulb from the bulb
socket by pulling it straight out.
4.
Install the new bulb in the bulb
socket.
5.
Install the bulb socket into the
headlamp assembly by turning
clockwise.
Back-Up Lamps
1.
Locate the back-up lamp
assembly underneath the rear
fascia.
2.
Remove the bulb from the lamp
assembly by turning it
counterclockwise and pulling
straight out.
3.
Remove the bulb and replace.
4.
Reverse Steps 2 and 3 for
assembly.
Electrical System
Electrical System
Overload
The vehicle has fuses and circuit
breakers to protect against an
electrical system overload.
When the current electrical load is
too heavy, the circuit breaker opens
and closes, protecting the circuit
until the current load returns to
normal or the problem is fixed. This
greatly reduces the chance of circuit
overload and fire caused by
electrical problems.
Fuses and circuit breakers protect
power devices in the vehicle.
Replace a bad fuse with a new one
of the identical size and rating.
If there is a problem on the road and
a fuse needs to be replaced, the
same amperage fuse can be
borrowed. Choose some feature of
the vehicle that is not needed to use
and replace it as soon as possible.
Vehicle Care
275
Headlamp Wiring
An electrical overload may cause
the lamps to go on and off, or in
some cases to remain off. Have the
headlamp wiring checked right away
if the lamps go on and off or
remain off.
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected
from electrical overload, overload
due to heavy snow or ice may
cause wiper linkage damage.
Always clear ice and heavy snow
from the windshield before using the
windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Fuses and Circuit
Breakers
The wiring circuits in the vehicle are
protected from short circuits by a
combination of fuses and circuit
breakers. This greatly reduces the
chance of damage caused by
electrical problems.
To check a fuse, look at the
silver-colored band inside the fuse.
If the band is broken or melted,
replace the fuse. Be sure to replace
a bad fuse with a new one of the
identical size and rating.
Fuses of the same amperage can
be temporarily borrowed from
another fuse location, if a fuse goes
out. Replace the fuse as soon as
possible.
To identify and check fuses, circuit
breakers, and relays, see
Engine
Compartment Fuse Block
0
275
,
Instrument Panel Fuse Block
0
279
,
and
Rear Compartment Fuse
Block
0
281
.
Engine Compartment
Fuse Block
The underhood fuse block is in the
engine compartment, on the driver
side of the vehicle.
Caution
Do not pull engine compartment
fuse block lever, since it is
intended only for service
purposes. If pulled, vehicle
malfunction may occur.
276
Vehicle Care
Caution
Spilling liquid on any electrical
component on the vehicle may
damage it. Always keep the
covers on any electrical
component.
To remove the fuse block cover,
press the clips on the cover and lift
it straight up.
Engine Compartment Fuse Block
Vehicle Care
277
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Fuses
Usage
F1
ABS pump
F2
Starter 1
F3
DC DC transformer 1
F4
F5
F6
F7
DC DC transformer 2
F8
Starter 3
F9
F10
F11
F12
Front wiper
F13
Starter 2
F14
LED/Automatic
headlamp leveling (if
equipped)
F15
Rear wiper 1
F16
F17
Fuses
Usage
F18
Automatic headlamp
leveling (if equipped)
F19
F20
F21
F22
Electronic brake
control module
F23
Parking/Trailer
lamps
F24
Right trailer
stoplamp/Turnlamp
F25
Steering column lock
F26
F27
Left trailer stoplamp/
Turnlamp
F28
F29
F30
Washer pump
F31
Right low-beam
headlamp
F32
Left low-beam
headlamp
Fuses
Usage
F33
Fog lamps
F34
Horn
F35
F36
Left high-beam
headlamp
F37
Right high-beam
headlamp
F38
Automatic headlamp
leveling (if equipped)
F39
Transmission control
module 1
F40
Left rear bus
electrical center/
Ignition
F41
Instrument cluster
F42
HVAC
F43
Head-up display
F44
F45
F46
F47
F48
Rear wiper 2
278
Vehicle Care
Fuses
Usage
F49
Interior rearview
mirror/Trailer
F50
Fuel system control
module
F51
Heated steering
wheel
F52
A/C clutch
F53
Transmission range
control module
F54
Coolant pump
F55
F56
F57
Engine control
module/Ignition
F58
Transmission control
module/Ignition
F59
Engine control
module battery
F60
Transmission control
module 2
F61
O2 sensor 1/
Aeroshutter
Fuses
Usage
F62
Engine control
module
odd
F63
O2 sensor 2
F64
Engine control
module
even
F65
Engine control
module powertrain 1
F66
Engine control
module powertrain 2
F67
Powertrain TRCM
F68
F69
F70
F71
F72
F73
F74
F75
F76
F77
K1
Starter 1
Fuses
Usage
K2
Run/Crank
K3
Starter 3
K4
LED/Automatic
headlamps (if
equipped)
K5
K6
Coolant pump
K7
Engine control
module
K8
A/C
K9
K10
Starter 2
Vehicle Care
279
Instrument Panel Fuse
Block
The instrument panel fuse block is
in the center console between the
driver and passenger seats. To
access the fuses, open the fuse
panel door, or remove the panel
from the passenger side by pulling
it out.
To reinstall the door, push the door
back into its original location.
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Instrument Panel Fuse Block
Vehicle Care
281
Rear Compartment Fuse
Block
The rear compartment fuse block is
in the cargo area, on the driver side
of the vehicle behind the lower trim
panel. To open, turn the latch with a
flat bladed tool and pull the trim
panel from the edges to fold it down.
The label for this fuse block is in the
spare tire area, on the foam under
the cargo floor.
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Rear Compartment Fuse Block
Fuses
Usage
F1
F2
Trailer battery 1
F3
Driver safety belt
F4
Rear blower
F5
Rear drive control
F6
Passenger
safety belt
F7
Right window
F8
Rear defogger
F9
Left window
F10
F11
Trailer reverse
F12
F13
F14
F15
F16
F17
Camera
F18
Trailer module
282
Vehicle Care
Fuses
Usage
F19
Ventilated seats
F20
F21
Trailer connector
F22
F23
F24
Passenger window
switch
F25
F26
Trailer brake
F27
Driver ventilated
seat/Lumbar
F28
Passive entry/
Passive start
F29
F30
Canister vent
F31
F32
Heated mirror
F33
F34
Logic mode
F35
Fuel system control
module
Fuses
Usage
F36
Passenger ventilated
seat/Lumbar
F37
F38
Window module
F39
Rear closure
F40
Memory seat module
F41
Automatic
occupancy sensor
F42
Trailer battery 2
F43
F44
F45
Liftgate
F46
Rear heated seats
F47
F48
Glass breakage
F49
F50
F51
F52
Semi-active dampen
system module
Fuses
Usage
F53
Rear parking aid
module
F54
External object
calculating
F55
F56
Universal garage
door opener/Rain
sensor
F57
Theft deterrent
CB1
CB2
CB3
APO rear
K1
K2