Cadillac Escalade - 2017 Fuse Box Diagram

Cadillac Escalade - 2017 Fuse Box Diagram

INTRODUCTION
3
{
Warning
Warning indicates a hazard that
could result in injury or death.
Caution
Caution indicates a hazard that
could result in property or vehicle
damage.
A circle with a slash through it is a
safety symbol which means
Do Not,
Do not do this,
or
Do not let this
happen.
Symbols
The vehicle has components and
labels that use symbols instead of
text. Symbols are shown along with
the text describing the operation or
information relating to a specific
component, control, message, gauge,
or indicator.
M
:
Shown when the owner manual
has additional instructions or
information.
*
:
Shown when the service manual
has additional instructions or
information.
0
:
Shown when there is more
information on another page
see page.
Vehicle Symbol Chart
Here are some additional symbols that
may be found on the vehicle and what
they mean. For more information on
the symbol, refer to the Index.
9
:
Airbag Readiness Light
#
:
Air Conditioning
G
:
Air Conditioning Refrigerant Oil
!
:
Antilock Brake System (ABS)
g
:
Audio Steering Wheel Controls or
OnStar
®
(if equipped)
$
:
Brake System Warning Light
I
:
Certified Technician
"
:
Charging System
I
:
Cruise Control
`
:
Do Not Puncture
^
:
Do Not Service
B
:
Engine Coolant Temperature
O
:
Exterior Lamps
_
:
Flame/Fire Prohibited
H
:
Flammable
.
:
Fuel Gauge
+
:
Fuses
3
:
Headlamp High/Low-Beam
Changer
(
:
Heated Steering Wheel
j
:
LATCH System Child Restraints
*
:
Malfunction Indicator Lamp
:
:
Oil Pressure
O
:
Power
/
:
Remote Vehicle Start
>
:
Safety Belt Reminders
h
:
Start/Stop
7
:
Tire Pressure Monitor
INSTRUMENTS AND CONTROLS
125
.
One on the rear of the center
console.
.
One in the third row seat on the
driver side.
.
One in the rear cargo area on the
passenger side.
Lift the cover to access and replace
when not in use.
The accessory power outlets are
powered as follows:
.
The power outlet near the
cupholders on the center console
is powered in Retained Accessory
Power (RAP) mode. This outlet can
be configured to operate using
RAP or battery power. If the power
outlet is used while in the battery
power mode, this could cause
interference between the RKE
transmitter and the vehicle, and
the vehicle may not start. See
Ignition Positions
0
205
.
.
The power outlets inside the
center console and on the rear of
the center console are powered
when the ignition is in ON/RUN/
START or ACC/ACCESSORY,
or until the driver door is opened
within 10 minutes of turning off
the vehicle. See
Retained Accessory
Power (RAP)
0
209
.
.
The power outlets in the third row
seat and in the rear cargo area are
powered at all times.
{
Warning
Power is always supplied to the
outlets. Do not leave electrical
equipment plugged in when the
vehicle is not in use because the
vehicle could catch fire and cause
injury or death.
Caution
Leaving electrical equipment
plugged in for an extended period
of time while the vehicle is off will
drain the battery. Always unplug
electrical equipment when not in
use and do not plug in equipment
that exceeds the maximum 15 amp
rating.
Certain power accessory plugs may
not be compatible with the accessory
power outlet and could overload
vehicle or adapter fuses. If a problem
is experienced, see your dealer.
When adding electrical equipment, be
sure to follow the proper installation
instructions included with the
equipment. See
Add-On Electrical
Equipment
0
265
.
Caution
Hanging heavy equipment from the
power outlet can cause damage not
covered by the vehicle warranty.
The power outlets are designed for
accessory power plugs only, such as
cell phone charge cords.
Power Outlet 110/120 Volt
Alternating Current
This power outlet can be used to plug
in electrical equipment that uses a
maximum limit of 150 watts.
The 110/120 volt power outlet is on
the rear of the center console.
INSTRUMENTS AND CONTROLS
127
Warning (Continued)
system does not detect a metal
object, and the object gets wedged
between the phone and charger,
remove the phone and allow the
metallic object to cool before
removing it from the charging pad,
to prevent burns.
To charge a mobile device:
1.
Remove all objects from the
charging pad. The system may
not charge if there are any
objects on the charging pad.
2.
Place the mobile device face up
on the
@
symbol on the
charging pad.
3.
The
~
will display on the
V
on the infotainment screen. This
indicates that the mobile device
is properly positioned and
charging. If a phone is placed on
the charging pad and
~
does
not display, remove the phone
from the pad, turn 180 degrees
and wait three seconds before
placing/aligning the phone on
the pad again.
Cigarette Lighter
If equipped with a cigarette lighter, it
is located in the center console near
the cupholders. Press on the access
door to open it and use the lighter.
To use the cigarette lighter, push it in
all the way, and let go. When it is
ready, it will pop back out by itself.
Caution
Holding a cigarette lighter in while
it is heating does not let the lighter
back away from the heating
element when it is hot. Damage
from overheating can occur to the
lighter or heating element, or a fuse
could be blown. Do not hold a
cigarette lighter in while it is
heating.
LIGHTING
175
other exterior lamps come on. The
transition time for the lamps coming
on varies based on wiper speed. When
the wipers are not operating, these
lamps turn off. Move the exterior
lamp control to
P
or
;
to disable
this feature.
Hazard Warning Flashers
|
:
Press to make the front and rear
turn signal lamps flash on and off.
Press again to turn the flashers off.
When the hazard warning flashers are
on, the vehicle's turn signals will
not work.
Turn and Lane-Change
Signals
An arrow on the instrument cluster
flashes in the direction of the turn or
lane change.
Move the turn signal lever all the way
up or down to signal a turn.
Raise or lower the lever for less than
one second until the arrow starts to
flash to signal a lane change. This
causes the turn signals to
automatically flash three times. It will
flash six times if Tow/Haul Mode is
active. Holding the turn signal lever
for more than one second will cause
the turn signals to flash until the
lever is released.
The lever returns to its starting
position whenever it is released.
If after signaling a turn or a lane
change the arrows flash rapidly or do
not come on, a signal bulb could be
burned out.
Replace any burned out bulbs. If a
bulb is not burned out, check the fuse.
See
Fuses
0
291
.
Turn Signal On Chime
If the turn signal is left on for more
than 1.2 km (0.75 mi), a chime sounds
at each flash of the turn signal. The
message TURN SIGNAL ON will also
appear in the Driver Information
Center (DIC). To turn the chime and
message off, move the turn signal
lever to the off position.
208
DRIVING AND OPERATING
end of the cord, which will prevent
engine heater operation at
temperatures above
18 °C (0 °F).
To Use the Engine Heater
1.
Turn off the engine.
2.
Open the hood and unwrap the
electrical cord. The cord is by the
left front fender, next to the
engine compartment fuse block.
Check the heater cord for
damage. If it is damaged, do not
use it. See your dealer for a
replacement. Inspect the cord for
damage yearly.
3.
Plug the cord into a normal,
grounded 110-volt AC outlet.
{
Warning
Improper use of the heater cord or
an extension cord can damage the
cord and may result in overheating
and fire.
.
Plug the cord into a
three-prong electrical utility
receptacle that is protected by
(Continued)
Warning (Continued)
a ground fault detection
function. An ungrounded
outlet could cause an electric
shock.
.
Use a weatherproof,
heavy-duty, 15 amp-rated
extension cord if needed.
Failure to use the
recommended extension cord
in good operating condition,
or using a damaged heater or
extension cord, could make it
overheat and cause a fire,
property damage, electric
shock, and injury.
.
Do not operate the vehicle
with the heater cord
permanently attached to the
(Continued)
Warning (Continued)
vehicle. Possible heater cord
and thermostat damage could
occur.
.
While in use, do not let the
heater cord touch vehicle
parts or sharp edges. Never
close the hood on the
heater cord.
.
Before starting the vehicle,
unplug the cord, reattach the
cover to the plug, and
securely fasten the cord. Keep
the cord away from any
moving parts.
4.
Before starting the engine, be
sure to unplug and store the cord
as it was before to keep it away
from moving engine parts. If you
do not, it could be damaged.
The length of time the heater should
remain plugged in depends on several
factors. Ask a dealer in the area where
you will be parking the vehicle for the
best advice on this.
VEHICLE CARE
271
1.
Positive (+) Terminal. See
Jump
Starting - North America
0
330
.
2.
Battery - North America
0
284
.
3.
Coolant Surge Tank and Pressure
Cap. See
Cooling System
0
276
.
4.
Engine Air Cleaner/Filter
0
275
.
5.
Remote Negative (
) Location
(Out of View). See
Jump Starting -
North America
0
330
.
6.
Engine Cooling Fans (Out of
View). See
Cooling System
0
276
.
7.
Engine Oil Fill Cap. See
When to
Add Engine Oil
under
Engine
Oil
0
271
.
8.
Engine Oil Dipstick. See
Checking Engine Oil
under
Engine Oil
0
271
.
9.
Windshield Washer Fluid
Reservoir. See
Adding Washer
Fluid
under
Washer Fluid
0
281
.
10.
Brake Fluid Reservoir. See
Brake
Fluid
0
283
.
11.
Engine Compartment Fuse
Block
0
291
.
Engine Oil
To ensure proper engine performance
and long life, careful attention must
be paid to engine oil. Following these
simple, but important steps will help
protect your investment:
.
Use engine oil approved to the
proper specification and of the
proper viscosity grade. See
Selecting the Right Engine Oil
in
this section.
.
Check the engine oil level regularly
and maintain the proper oil level.
See
Checking Engine Oil
and
When to Add Engine Oil
in this
section.
.
Change the engine oil at the
appropriate time. See
Engine Oil
Life System
0
273
.
.
Always dispose of engine oil
properly. See
What to Do with
Used Oil
in this section.
Checking Engine Oil
Check the engine oil level regularly,
every 650 km (400 mi), especially prior
to a long trip. The engine oil dipstick
handle is a loop. See
Engine
Compartment Overview
0
270
for the
location.
{
Warning
The engine oil dipstick handle may
be hot; it could burn you. Use a
towel or glove to touch the dipstick
handle.
If a low oil Driver Information Center
(DIC) message displays, check the oil
level.
Follow these guidelines:
.
To get an accurate reading, park
the vehicle on level ground. Check
the engine oil level after the
engine has been off for at least
two hours. Checking the engine oil
level on steep grades or too soon
after engine shutoff can result in
incorrect readings. Accuracy
improves when checking a cold
engine prior to starting. Remove
the dipstick and check the level.
.
If unable to wait two hours, the
engine must be off for at least
15 minutes if the engine is warm,
290
VEHICLE CARE
1.
Bulb Socket
2.
Bulb
3.
Lamp Assembly
To replace one of these bulbs:
1.
Push the lamp assembly (3)
toward the center of the vehicle.
2.
Pull the lamp assembly down to
remove.
3.
Turn the bulb socket (1)
counterclockwise to remove it
from the lamp assembly (3).
4.
Pull the bulb (2) straight out of
the bulb socket (1).
5.
Push the replacement bulb
straight into the bulb socket and
turn the bulb socket clockwise to
install it into the lamp assembly.
6.
Push the lamp assembly back
into position until the release tab
locks into place.
Replacement Bulbs
Exterior Lamp
Bulb
Number
License Plate Lamp
W5W LL
For replacement bulbs not listed here,
contact your dealer.
Electrical System
Electrical System Overload
The vehicle has fuses to protect
against an electrical system overload.
Fuses also protect power devices in
the vehicle.
Replace a bad fuse with a new one of
the identical size and rating.
If there is a problem on the road and
a fuse needs to be replaced, there are
some spare fuses and a fuse puller in
the left instrument panel fuse block.
The same amperage fuse can also be
borrowed. Choose some feature of the
vehicle that is not needed to use and
replace it as soon as possible.
Headlamp Wiring
An electrical overload may cause the
lamps to go on and off, or in some
cases to remain off. Have the
headlamp wiring checked right away if
the lamps go on and off or remain off.
VEHICLE CARE
291
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected from
electrical overload, overload due to
heavy snow or ice may cause wiper
linkage damage. Always clear ice and
heavy snow from the windshield
before using the windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Fuses
The wiring circuits in the vehicle are
protected from short circuits by fuses.
This greatly reduces the chance of
fires caused by electrical problems.
Look at the silver-colored band inside
the fuse. If the band is broken or
melted, replace the fuse. Be sure you
replace a bad fuse with a new one of
the identical size and rating.
Fuses of the same amperage can be
temporarily borrowed from another
fuse location, if a fuse goes out.
Replace the fuse as soon as you can.
Engine Compartment Fuse
Block
The engine compartment fuse block is
in the engine compartment, on the
driver side of the vehicle.
Lift the cover to access the fuse block.
Caution
Spilling liquid on any electrical
component on the vehicle may
damage it. Always keep the covers
on any electrical component.
A fuse puller is available in the left
instrument panel fuse block.
VEHICLE CARE
295
Item
Usage
103
Auxiliary interior
heater
104
Starter
105
106
107
Aeroshutter
108
109
Police upfitter
110
111
112
Starter relay
113
114
Front windshield
washer
115
Rear window washer
116
Left cooling fan
117
Fuel pump prime
118
119
120
Fuel pump prime
121
Right HID headlamp
Item
Usage
122
Left HID headlamp
123
Right cooling fan
Instrument Panel Fuse
Block (Left)
The left instrument panel fuse block
access door is on the driver side edge
of the instrument panel.
Pull off the cover to access the fuse
block.
296
VEHICLE CARE
The vehicle may not be equipped with
all of the fuses, relays, and features
shown.
Item
Usage
1
2
Item
Usage
3
4
Accessory power
outlet 1
5
Retained accessory
power
6
APO/BATT
7
Universal garage door
opener/Interior
rearview mirror
8
SEO/Retained accessory
power
9
10
Body control module 3
11
Body control module 5
12
Steering wheel control
backlighting
13
14
15
16
Discrete logic ignition
sensor
17
Video processing
module
298
VEHICLE CARE
Instrument Panel Fuse
Block (Right)
The right instrument panel fuse block
access door is on the passenger side
edge of the instrument panel.
Pull off the cover to access the fuse
block.
The vehicle may not be equipped with
all of the fuses, relays, and features
shown.
Item
Usage
1
2
300
VEHICLE CARE
Rear Compartment Fuse
Block
The rear compartment fuse block is
behind the access panel on the left
side of the compartment.
Pull the panel out by grabbing the
finger access slot at the rear edge.
The vehicle may not be equipped with
all of the fuses, relays, and features
shown.
Item
Usage
1
Rear defogger relay
2
Left heated second
row seat
3
Right heated second
row seat
4
Heated mirrors
5
Liftgate
6
Glass breakage
7
Liftglass
8
Liftgate module logic
9
Rear wiper
10
Rear HVAC blower
11
Second row seat
12
Liftgate module
13
Third row seat
14
Rear accessory power
outlet
15
Rear defogger
16
Liftgate
17
Liftglass