Buick Regal - 2017 Fuse Box Diagram

Buick Regal - 2017 Fuse Box Diagram

98
Instruments and Controls
If the ignition is put in OFF while the
wipers are performing wipes due to
windshield washing, the wipers
continue to run until they reach the
base of the windshield.
Compass
The vehicle may have a compass
display on the Driver Information
Center (DIC). The compass receives
its heading and other information
from the Global Positioning
System (GPS) antenna,
StabiliTrak
®
, and vehicle speed
information.
The compass system is designed to
operate for a certain number of
miles or degrees of turn before
needing a signal from the GPS
satellites. When the compass
display shows CAL, drive the
vehicle for a short distance in an
open area where it can receive a
GPS signal. The compass system
will automatically determine when a
GPS signal is restored and provide
a heading again. See
Compass
Messages
0
126
for the messages
that may be displayed for the
compass.
Clock
Setting the Time and Date
To set the time or date:
1.
Select Settings from the Home
Page, then select Time and
Date Settings.
2.
Select the desired function.
To set the time or date, press
«
or
ª
to change the hour, minutes,
AM, PM, day, month, or year.
To change the 12-24 Hr setting,
press the 12-24 Hr button.
To turn Auto Set on and off, press
the Auto Set button.
If auto timing is set, the time
displayed on the clock may not
update immediately when driving
into a new time zone.
Press
q
BACK to go to the last
menu and save the changes or
{
to
return to the Home Page.
Power Outlets
Power Outlets 12 Volt Direct
Current
The accessory power outlet can be
used to plug in electrical equipment,
such as a cell phone or MP3 player.
There are two 12-volt accessory
power outlets:
.
On the center stack next to the
ashtray.
.
Inside the center console.
The outlet is powered when the
ignition is in ON/RUN or ACC/
ACCESSORY, or until the driver
door is opened within 10 minutes of
turning off the vehicle. See
Retained
Accessory Power (RAP)
0
172
.
Open the protective cover to use the
accessory power outlet.
Certain electrical accessories may
not be compatible with the
accessory power outlet and could
overload vehicle or adapter fuses.
If there is a problem, see your
dealer.
100
Instruments and Controls
Cigarette Lighter
If equipped, push the lighter down
and it will pop up when it is ready to
be used. The ignition switch must
be in the ACC/ACCESSORY or ON/
RUN position to use the lighter.
Caution
Holding a cigarette lighter in while
it is heating does not let the
lighter back away from the
heating element when it is hot.
Damage from overheating can
occur to the lighter or heating
element, or a fuse could be
blown. Do not hold a cigarette
lighter in while it is heating.
It is not recommended to use the
cigarette lighter to plug in auxiliary
electrical equipment.
Ashtrays
If equipped with an ashtray, it is
under the climate control system.
Press the ashtray cover to open. To
empty, grasp both sides of the
ashtray and remove.
Caution
If papers, pins, or other
flammable items are put in the
ashtray, hot cigarettes or other
smoking materials could ignite
them and possibly damage the
vehicle. Never put flammable
items in the ashtray.
Warning Lights,
Gauges, and
Indicators
Warning lights and gauges can
signal that something is wrong
before it becomes serious enough
to cause an expensive repair or
replacement. Paying attention to the
warning lights and gauges could
prevent injury.
Some warning lights come on briefly
when the engine is started to
indicate they are working. When
one of the warning lights comes on
and stays on while driving, or when
one of the gauges shows there may
be a problem, check the section that
explains what to do. Waiting to do
repairs can be costly and even
dangerous.
146
Lighting
The turn and lane-change signal
can be turned off manually by
moving the lever back to its original
position.
If after signaling a turn or lane
change the arrow flashes rapidly or
does not come on, a signal bulb
might be burned out.
Have any burned out bulbs
replaced. If the bulb is not burned
out, check the fuse. See
Fuses and
Circuit Breakers
0
237
.
Fog Lamps
To turn on the fog lamps,
if equipped, the ignition and the
headlamps or parking lamps must
be on.
#
:
If equipped, press to turn on or
off. An indicator light on the
instrument cluster comes on when
the fog lamps are on.
Some localities have laws that
require the headlamps to be on
along with the fog lamps.
Interior Lighting
Instrument Panel
Illumination Control
The brightness of the instrument
panel lighting and steering wheel
controls can be adjusted.
D
:
Move and hold the thumbwheel
up or down to brighten or dim the
lights.
Vehicle Care
215
1.
Engine Air Cleaner/Filter
0
220
.
2.
Engine Oil Fill Cap. See
Engine Oil
0
217
.
3.
Engine Oil Dipstick. See
Engine Oil
0
217
.
4.
Transmission Fluid Cap. See
Automatic Transmission
Fluid
0
220
.
5.
Brake Fluid Reservoir. See
Brake Fluid
0
229
.
6.
Coolant Surge Tank and
Pressure Cap. See
Engine
Coolant
0
223
.
7.
Battery (Under Cover). See
Battery - North America
0
230
.
8.
Engine Compartment Fuse
Block
0
237
.
9.
Windshield Washer Fluid
Reservoir. See
Washer
Fluid
0
227
.
Vehicle Care
217
1.
Engine Air Cleaner/Filter
0
220
.
2.
Engine Cover.
3.
Engine Oil Fill Cap. See
Engine Oil
0
217
.
4.
Engine Oil Dipstick. See
Engine Oil
0
217
.
5.
Transmission Fluid Cap and
Dipstick. See
Automatic
Transmission Fluid
0
220
.
6.
Brake Fluid Reservoir. See
Brake Fluid
0
229
.
7.
Coolant Surge Tank and
Pressure Cap. See
Engine
Coolant
0
223
.
8.
Battery (Under Cover). See
Battery - North America
0
230
.
9.
Engine Compartment Fuse
Block
0
237
.
10.
Windshield Washer Fluid
Reservoir. See
Washer
Fluid
0
227
.
Engine Oil
To ensure proper engine
performance and long life, careful
attention must be paid to engine oil.
Following these simple, but
important steps will help protect
your investment:
.
Use engine oil approved to the
proper specification and of the
proper viscosity grade. See
Selecting the Right Engine Oil
in this section.
.
Check the engine oil level
regularly and maintain the
proper oil level. See
Checking
Engine Oil
and
When to Add
Engine Oil
in this section.
.
Change the engine oil at the
appropriate time. See
Engine Oil
Life System
0
219
.
.
Always dispose of engine oil
properly. See
What to Do with
Used Oil
in this section.
Checking Engine Oil
It is a good idea to check the engine
oil level at each fuel fill. In order to
get an accurate reading, the oil
must be warm and the vehicle must
be on level ground. The engine oil
dipstick handle is a loop. See
Engine Compartment Overview
0
214
for the location of the engine
oil dipstick.
Obtaining an accurate oil level
reading is essential:
1.
If the engine has been running
recently, turn off the engine and
allow several minutes for the oil
to drain back into the oil pan.
Checking the oil level too soon
after engine shutoff will not
provide an accurate oil level
reading.
{
Warning
The engine oil dipstick handle
may be hot; it could burn you.
Use a towel or glove to touch the
dipstick handle.
2.
Pull out the dipstick and wipe it
with a clean paper towel or
cloth, then push it back in all
the way. Remove it again,
keeping the tip down, and
check the level.
236
Vehicle Care
1.
Bulb Socket
2.
Bulb
3.
Lamp Assembly
To replace one of these bulbs:
1.
Push the release tab toward
the lamp assembly.
2.
Pull the lamp assembly down
to remove.
3.
Turn the bulb socket (1)
counterclockwise to remove it
from the lamp assembly (3).
4.
Pull the bulb (2) straight out of
the bulb socket (1).
5.
Push the replacement bulb
straight into the bulb socket
and turn the bulb socket
clockwise to install it into the
lamp assembly.
6.
Push the lamp assembly back
into position until the release
tab locks into place.
Replacement Bulbs
Exterior Lamp
Bulb
Number
Back-up Lamp
W16W
or 921
Fog Lamp
H10
Front Turn Signal
Lamp (Base)
WY21W
Front Turn Signal
Lamp (Uplevel)
PSY24W
Low-Beam
Headlamp (Base)
HIR2
High-Beam
Headlamp (Base)
HIR2
License Plate Lamp
194
Daytime Running
Lamp (DRL) (Base)
W21/
5W ULL
Turn Signal Lamp
W21W
or 7440
Sidemarker Lamp
194
For replacement bulbs not listed
here, contact your dealer.
Electrical System
High Voltage Devices and
Wiring
{
Warning
Exposure to high voltage can
cause shock, burns, and even
death. The high voltage
components in the vehicle can
only be serviced by technicians
with special training.
High voltage components are
identified by labels. Do not
remove, open, take apart,
or modify these components.
High voltage cable or wiring has
orange covering or labels. Do not
probe, tamper with, cut, or modify
high voltage cable or wiring.
Electrical System
Overload
The vehicle has fuses and circuit
breakers to protect against an
electrical system overload.
Vehicle Care
237
When the current electrical load is
too heavy, the circuit breaker opens
and closes, protecting the circuit
until the current load returns to
normal or the problem is fixed. This
greatly reduces the chance of circuit
overload and fire caused by
electrical problems.
Fuses and circuit breakers protect
power devices in the vehicle.
Replace a bad fuse with a new one
of the identical size and rating.
If there is a problem on the road and
a fuse needs to be replaced, the
same amperage fuse can be
borrowed. Choose some feature of
the vehicle that is not needed to use
and replace it as soon as possible.
Headlamp Wiring
An electrical overload may cause
the lamps to go on and off, or in
some cases to remain off. Have the
headlamp wiring checked right away
if the lamps go on and off or
remain off.
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected
from electrical overload, overload
due to heavy snow or ice may
cause wiper linkage damage.
Always clear ice and heavy snow
from the windshield before using the
windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Fuses and Circuit
Breakers
The wiring circuits in the vehicle are
protected from short circuits by a
combination of fuses and circuit
breakers. This greatly reduces the
chance of damage caused by
electrical problems.
To check a fuse, look at the
silver-colored band inside the fuse.
If the band is broken or melted,
replace the fuse. Be sure to replace
a bad fuse with a new one of the
identical size and rating.
Fuses of the same amperage can
be temporarily borrowed from
another fuse location, if a fuse goes
out. Replace the fuse as soon as
possible.
To identify and check fuses, circuit
breakers, and relays, see
Engine
Compartment Fuse Block
0
237
and
Instrument Panel Fuse Block
0
240
.
Engine Compartment
Fuse Block
238
Vehicle Care
To remove the fuse block cover,
press the three retaining clips on the
cover and lift it straight up.
Caution
Spilling liquid on any electrical
component on the vehicle may
damage it. Always keep the
covers on any electrical
component.
Engine Compartment Fuse Block
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Fuse
Usage
1
Transmission control
module
2
Engine control
module
3
Fuse
Usage
4
5
Ignition/
Transmission control
module/Engine
control module
6
Windshield wiper
7
BPIM (eAssist only)
Vehicle Care
239
Fuse
Usage
8
9
Fuel injection/
Ignition system
10
Engine control
module
11
O2 sensor
12
Starter
13
Fuel system control
module
14
Trunk release
15
MGU coolant pump
(eAssist only)
16
Heated steering
wheel
17
18
BPIM (eAssist only)
19
20
21
Rear power windows
22
ABS valve
23
Obstacle detection
Fuse
Usage
24
Front power
windows
25
Power outlets
26
ABS pump
27
Electric parking
brake
28
Rear window
defogger
29
Driver seat lumbar
30
Passenger seat
lumbar
31
A/C clutch
32
Body control
module 6
33
Heated front seats
34
Sunroof
35
Infotainment system
36
Adaptive cruise
37
Right high-beam
headlamp
38
Left high-beam
headlamp
Fuse
Usage
39
AWD
40
41
Vacuum pump
42
Radiator fan
43
Passive entry/
Passive start
44
Transmission
auxiliary pump
(eAssist only)
45
Radiator fan
46
Terminal 87/Main
relay
47
O2 sensor
48
Fog lamps
49
Right low-beam HID
headlamp
50
Left low-beam HID
headlamp
51
Horn
52
Malfunction
indicator lamp
53
Interior rearview
mirror
240
Vehicle Care
Fuse
Usage
54
Rear vision camera
55
Power windows/
Mirrors
56
Windshield washer
57
58
59
Secondary air
induction
(eAssist only)
60
Heated mirrors
61
62
Canister vent
solenoid
63
64
HVAC pump
(eAssist only)
65
66
SAI check valve
(eAssist only)
67
Fuel system control
module
68
Fuse
Usage
69
Battery sensor
70
Right low-beam
headlamp/DRL
71
Relay
Usage
1
A/C control
2
Starter
3
4
Front wiper (step 2)
5
Front wiper (step 1)
6
Right low-beam
headlamp/DRL
7
Main relay
8
Auxiliary heater
pump (eAssist only)
9
Cooling fan
10
Cooling fan
11
Transmission
auxiliary pump
(eAssist only)
12
Relay
Usage
13
Cooling fan
14
HID headlamps/Left
low-beam
headlamp/DRL
15
Ignition
16
Secondary AIR
pump (eAssist only)
17
Window/Mirror
defogger
Instrument Panel Fuse
Block
Vehicle Care
241
The instrument panel fuse block is
located in the instrument panel, on
the driver side of the vehicle.
To access the fuses, open the
storage compartment. Press in on
the sides of the compartment to
release it from the instrument panel.
Pull the door toward you to release
it from the hinge.
Instrument Panel Fuse Block
Item
Usage
1
Suspension control
module/Universal
garage door
opener/ESC
Item
Usage
2
Body control
module 1
3
Body control
module 5
4
Radio
5
Radio displays/
Parking assist/
Infotainment/Module
tunnel control
6
Instrument panel
power outlet
7
Console power
outlet
8
Body control
module 3
9
Body control
module 4
10
Body control
module 8
11
Front HVAC blower
12
Right front seat
13
Left front seat
Item
Usage
14
Diagnostic link
connector
15
Airbag
16
Steering wheel
controls
17
HVAC controller
18
Service fuse/
Logistics relay
19
Memory seats
20
Automatic occupant
sensing
21
Instrument cluster
22
Discrete logic
ignition switch/
Passive entry/
Passive start
23
Body control
module 6
24
Body control
module 2
25
OnStar
26