Buick Enclave - 2016 Fuse Box Diagram

Buick Enclave - 2016 Fuse Box Diagram

Keys, Doors, and Windows
37
If the delayed locking feature is
active, the alarm is not activated
until all doors are closed and the
security light goes off.
.
Press
Q
when the driver door is
closed. The security light comes
on solid for approximately
30 seconds and then goes off.
The content theft-deterrent alarm
is not armed until the security
light goes off.
The theft-deterrent system will not
activate if the doors are locked with
the vehicle's key or the manual
door lock.
If the driver door is opened without
first unlocking with the RKE
transmitter, the horn will chirp and
the lights will flash to indicate
pre-alarm. If the vehicle is not
started, or the door is not unlocked
by pressing
K
on the RKE
transmitter during the 10-second
pre-alarm, the alarm will be
activated.
The alarm will also be activated if a
passenger door, the liftgate, or the
hood is opened without first
disarming the system. When the
alarm is activated, the turn signals
flash and the horn sounds for about
30 seconds. The alarm system will
then re-arm to monitor for the next
unauthorized event.
The vehicle can be started with the
correct ignition key if the alarm has
been set off.
To avoid setting off the alarm by
accident:
.
Lock the vehicle with the door
key after the doors are closed.
.
Unlock the door with the RKE
transmitter. Unlocking a door any
other way sets off the alarm if
the system has been armed.
Press
K
or place the key in the
ignition and turn it to START to turn
off the alarm.
Testing the Alarm
To test the alarm:
1.
From inside the vehicle, lower
the driver side window, and
open the driver door.
2.
Press
Q
.
3.
Get out of the vehicle, close
the door, and wait for the
security light to go out.
4.
Reach in through the window,
unlock the door with the
manual door lock, and open
the door. This should set off the
alarm.
If the alarm does not sound when it
should, but the headlamps flash,
check to see if the horn works. The
horn fuse may be blown. To replace
the fuse, see
Fuses and Circuit
Breakers
0
257
.
If the alarm does not sound or the
headlamps do not flash, see your
dealer for service.
Immobilizer
See
Radio Frequency Statement
0
336
.
Immobilizer Operation
This vehicle has PASS-Key
®
III+
(Personalized Automotive Security
System) theft-deterrent system.
PASS-Key III+ is a passive
theft-deterrent system.
38
Keys, Doors, and Windows
The system is automatically armed
when the key is removed from the
ignition.
The system is automatically
disarmed when the key is turned to
ON/RUN, ACC/ACCESSORY,
or START from the LOCK/OFF
position.
You do not have to manually arm or
disarm the system.
The security light comes on if there
is a problem with arming or
disarming the theft-deterrent
system.
When the PASS-Key III+ system
senses an incorrect key, the vehicle
does not start. Anyone using a
trial-and-error method to start the
vehicle will be discouraged because
of the high number of electrical key
codes.
If the engine does not start and the
security light on the instrument
panel comes on when trying to start
the vehicle, there may be a problem
with the theft-deterrent system. Turn
the ignition off and try again.
If the engine still does not start, and
the key appears to be undamaged,
try another ignition key and check
the fuses. See
Fuses and Circuit
Breakers
0
257
for additional
information. If the engine still does
not start with the other key, the
vehicle needs service. If the vehicle
does start, the first key may be
faulty. See your dealer who can
service the PASS-Key III+ to have a
new key made. In an emergency,
contact Roadside Assistance. See
Roadside Assistance Program
0
330
.
It is possible for the PASS-Key III+
decoder to learn the transponder
value of a new or replacement key.
Up to 10 keys may be programmed
to the vehicle. The following
procedure is for programming
additional keys only. If all currently
programmed keys are lost or do not
operate, you must see your dealer
or a locksmith who can service
PASS-Key III+ to have keys made
and programmed to the system.
See your dealer or a locksmith who
can service PASS-Key III+ to get a
new key blank that is cut exactly as
the ignition key that operates the
system.
To program the new additional key:
1.
Verify that the new key has a
1
stamped on it.
2.
Insert the already programmed
key in the ignition and start the
engine. If the engine does not
start, see your dealer for
service.
3.
After the engine has started,
turn the key to LOCK/OFF, and
remove the key.
4.
Insert the key to be
programmed and turn it to the
ON/RUN position within
five seconds of the original key
being turned to the LOCK/OFF
position.
The security light turns off once
the key has been programmed.
5.
Repeat Steps 1
4 if additional
keys are to be programmed.
Instruments and Controls
105
Power Outlets
The vehicle has 12-volt outlets that
can be used to plug in electrical
equipment, such as a cell phone or
MP3 player.
The power outlets are located:
.
On the center stack below the
climate controls.
.
Inside the center console.
.
At the rear of the center console.
.
In the rear cargo area.
Lift the cover to access the outlet
and replace when not in use.
{
Warning
Power is always supplied to the
outlets. Do not leave electrical
equipment plugged in when the
vehicle is not in use because the
vehicle could catch fire and cause
injury or death.
Caution
Leaving electrical equipment
plugged in for an extended period
of time while the vehicle is off will
drain the battery. Always unplug
electrical equipment when not in
use and do not plug in equipment
that exceeds the maximum
20 amp rating.
Certain accessory plugs may not be
compatible with the accessory
power outlet and could overload
vehicle and adapter fuses. If a
problem is experienced, see your
dealer.
When adding electrical equipment,
be sure to follow the proper
installation instructions included with
the equipment. See
Add-On
Electrical Equipment
0
231
.
Caution
Hanging heavy equipment from
the power outlet can cause
damage not covered by the
vehicle warranty. The power
outlets are designed for
accessory power plugs only, such
as cell phone charge cords.
Power Outlet 110V/120V
Alternating Current
If equipped with this power outlet it
can be used to plug in electrical
equipment that uses a maximum
limit of 150 watts.
The power outlet is on the rear of
the center console.
146
Lighting
Turn and Lane-Change
Signals
Move the turn signal lever all the
way up or down to signal a turn.
An arrow on the instrument cluster
flashes in the direction of the turn or
lane change.
Raise or lower the lever until the
arrow starts to flash to signal a lane
change. Hold it there until the lane
change is completed. If the lever is
briefly pressed and released, the
turn signal flashes three times.
The lever returns to its starting
position whenever it is released.
If after signaling a turn or lane
change the arrow flashes rapidly or
does not come on, a signal bulb
may be burned out.
Have any burned out bulbs
replaced. If a bulb is not burned out,
check the fuse. See
Fuses and
Circuit Breakers
0
257
.
Turn Signal On Chime
If either one of the turn signals is left
on and the vehicle has been driven
more than 1.2 km (0.75 mi), a chime
will sound.
Interior Lighting
Instrument Panel
Illumination Control
The instrument panel brightness
knob is located on the instrument
panel to the left of the steering
column.
D
(Instrument Panel
Brightness) :
Push the knob in all
the way until it extends out and
then turn the knob clockwise or
counterclockwise to brighten or dim
the lights. Push the knob back in
when finished.
230
Driving and Operating
Safety Chains
Always attach chains between the
vehicle and the trailer. Cross the
safety chains under the tongue of
the trailer to help prevent the tongue
from contacting the road if it
becomes separated from the hitch.
Always leave just enough slack so
the rig can turn. Never allow safety
chains to drag on the ground.
Trailer Brakes
A loaded trailer that weighs more
than 450 kg (1,000 lb) needs to have
its own brake system that is
adequate for the weight of the
trailer. Be sure to read and follow
the instructions for the trailer brakes
so they are installed, adjusted, and
maintained properly.
Because the vehicle has antilock
brakes, do not try to tap into the
vehicle's hydraulic brake system.
If you do, both brake systems will
not work well, or at all.
Trailer Wiring Harness
Basic Trailer Wiring
The trailer wiring harness, with a
seven-pin connector, is located at
the rear of the vehicle and is tied to
the vehicle's frame. The harness
connector can be plugged into a
seven-pin universal heavy-duty
trailer connector available through
your dealer.
The seven-wire harness contains
the following trailer circuits:
.
Yellow: Left Stop/Turn Signal
.
Dark Green: Right Stop/Turn
Signal
.
Brown: Taillamps
.
Black: Ground
.
Light Green: Back-up Lamps
.
Red/Black: Battery Feed
.
Dark Blue: Trailer Brake*
*The fuse for this circuit is installed
in the underhood electrical center,
but the wires are not connected.
They should be connected by your
dealer or a qualified service center.
If the back-up lamp circuit is not
functional, contact your dealer.
If a remote (non-vehicle) battery is
being charged, press the Tow/Haul
mode switch located on the center
console near the climate controls.
This will boost the vehicle system
voltage and properly charge the
battery. If the trailer is too light for
Tow/Haul mode, turn on the
headlamps (non-HID only) as a
second way to boost the vehicle
system and charge the battery.
Vehicle Care
237
1.
Remote Negative (
) Terminal.
See
Jump Starting - North
America
0
292
.
2.
Engine Compartment Fuse
Block
0
257
.
3.
Radiator Pressure Cap (Out of
View). See
Cooling System
0
242
.
4.
Engine Coolant Recovery Cap.
See
Cooling System
0
242
.
5.
Remote Positive (+) Terminal.
See
Jump Starting - North
America
0
292
.
6.
Power Steering Reservoir and
Cap (Under Engine Cover).
See
Power Steering Fluid
0
248
.
7.
Engine Oil Fill Cap. See
When
to Add Engine Oil
under
Engine Oil
0
237
.
8.
Engine Oil Dipstick (Out of
View). See
Checking Engine
Oil
under
Engine Oil
0
237
.
9.
Engine Cooling Fans (Out of
View). See
Cooling System
0
242
.
10.
Engine Cover
0
237
.
11.
Brake Fluid Reservoir. See
Brake Fluid
0
250
.
12.
Windshield Washer Fluid
Reservoir. See
Adding Washer
Fluid
under
Washer Fluid
0
249
.
13.
Engine Air Cleaner/Filter
0
241
.
Engine Cover
1.
Oil Fill Cap
2.
Engine Cover
To remove:
1.
Remove the oil fill cap (1).
2.
Raise the engine cover (2) to
release it from the retainers.
3.
Lift and remove the engine
cover.
4.
Reverse Steps 1
3 to reinstall
engine cover.
Engine Oil
To ensure proper engine
performance and long life, careful
attention must be paid to engine oil.
Following these simple, but
important steps will help protect
your investment:
.
Always use engine oil approved
to the proper specification and of
the proper viscosity grade. See
Selecting the Right Engine Oil
in this section.
.
Check the engine oil level
regularly and maintain the
proper oil level. See
Checking
Engine Oil
and
When to Add
Engine Oil
in this section.
.
Change the engine oil at the
appropriate time. See
Engine Oil
Life System
0
240
.
256
Vehicle Care
Replacement Bulbs
Exterior Lamp
Bulb
Number
License Plate Lamp
194LL
Rear Turn Signal
and Taillamps
7443
(W21/5W)
For replacement bulbs not listed
here, contact your dealer.
Electrical System
High Voltage Devices and
Wiring
{
Warning
Exposure to high voltage can
cause shock, burns, and even
death. The high voltage
components in the vehicle can
only be serviced by technicians
with special training.
High voltage components are
identified by labels. Do not
remove, open, take apart,
or modify these components.
High voltage cable or wiring has
orange covering. Do not probe,
tamper with, cut, or modify high
voltage cable or wiring.
Electrical System
Overload
The vehicle has fuses and circuit
breakers to protect against an
electrical system overload.
When the current electrical load is
too heavy, the circuit breaker opens
and closes, protecting the circuit
until the current load returns to
normal or the problem is fixed. This
greatly reduces the chance of circuit
overload and fire caused by
electrical problems.
Fuses and circuit breakers protect
power devices in the vehicle.
Replace a bad fuse with a new one
of the identical size and rating.
If there is a problem on the road and
a fuse needs to be replaced, the
same amperage fuse can be
borrowed. Choose some feature of
the vehicle that is not needed to use
and replace it as soon as possible.
Vehicle Care
257
Headlamp Wiring
An electrical overload may cause
the lamps to go on and off, or in
some cases to remain off. Have the
headlamp wiring checked right away
if the lamps go on and off or
remain off.
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected
from electrical overload, overload
due to heavy snow or ice may
cause wiper linkage damage.
Always clear ice and heavy snow
from the windshield before using the
windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Fuses and Circuit
Breakers
The wiring circuits in your vehicle
are protected from short circuits by
a combination of fuses, circuit
breakers and fusible thermal links.
This greatly reduces the chance of
fires caused by electrical problems.
Look at the silver-colored band
inside the fuse. If the band is broken
or melted, replace the fuse. Be sure
you replace a bad fuse with a new
one of the identical size and rating.
Fuses of the same amperage can
be temporarily borrowed from
another fuse location, if a fuse goes
out. Replace the fuse as soon as
you can.
Engine Compartment
Fuse Block
The underhood fuse block is in the
engine compartment, on the
passenger side of the vehicle.
Lift the cover for access to the fuse/
relay block.
Caution
Spilling liquid on any electrical
component on the vehicle may
damage it. Always keep the
covers on any electrical
component.
To remove fuses, hold the end of
the fuse between your thumb and
index finger and pull straight out.
258
Vehicle Care
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Fuses
Usage
A/C CLTCH
Air Conditioning
Clutch
Fuses
Usage
ABS MTR
Antilock Brake
System (ABS)
Motor
AFS
Adaptive Forward
Lighting System
AIRBAG
Airbag System
AUX POWER
Auxiliary Power
AUX
VAC PUMP
Auxiliary
Vacuum Pump
AWD
All-Wheel-Drive
System
BATT 1
Battery 1
BATT 2
Battery 2
BATT 3
Battery 3
CIGAR
LIGHTER
Cigarette Lighter
ECM 1
Engine Control
Module 1
ECM/
FPM IGN
Engine Control
Module/Fuel Pump
Control Module
Ignition
EMISSION 1
Emission 1
Vehicle Care
259
Fuses
Usage
EMISSION 2
Emission 2
EVEN COILS
Even Injector Coils
FAN 1
Cooling Fan 1
FAN 2
Cooling Fan 2
*
Headlamp Washer
(China)/Trailer
Brake
FPM
Fuel Pump Power
Module
FOG
LAMP (GMC)
Fog Lamps (GMC)
HTD
STR WHL
Heated Steering
Wheel
HORN
Horn
HTD MIR
Heated Outside
Rearview Mirror
HUMIDITY/
MAF
Humidity Sensor/
MAF Sensor
HVAC BLWR
Heating,
Ventilation, and Air
Conditioning
Blower
Fuses
Usage
LT HI BEAM
Left High-Beam
Headlamp
LT LO BEAM
Left Low-Beam
Headlamp
LT PRK
Left Parking Lamp
LT TRLR
STOP/TRN
Trailer Left
Stoplamp and Turn
Signal
ODD COILS
Odd Injector Coils
PWR L/GATE
Power Liftgate
PWR
OUTLET
Power Outlet
RR APO
Rear Accessory
Power Outlet
RR DEFOG
Rear Defogger
RR HVAC
Rear Climate
Control System
RT HI BEAM
Right High-Beam
Headlamp
RT LO BEAM
Right Low-Beam
Headlamp
RT PRK
Right
Parking Lamp
Fuses
Usage
RT TRLR
STOP/TRN
Trailer Right
Stoplamp and Turn
Signal
RVC SNSR
Regulated Voltage
Control Sensor
S/ROOF/
SUNSHADE
Sunroof
SERVICE
Service Repair
SPARE
Spare
STOP
LAMPS
(CHINA
ONLY)
Stoplamps
(China Only)
STRTR
Starter
TCM
Transmission
Control Module
TRANS
Transmission
TRLR
BCK/UP
Trailer Back-up
Lamps
TRLR BRK
Trailer Brake
TRLR
PRK LAMP
Trailer Parking
Lamps
TRLR PWR
Trailer Power
260
Vehicle Care
Fuses
Usage
WPR/WSW
Windshield Wiper/
Washer
Relays
Usage
A/C
CMPRSR
CLTCH
Air Conditioning
Compressor Clutch
AUX
VAC PUMP
Auxiliary
Vacuum Pump
CRNK
Switched Power
FAN 1
Cooling Fan 1
FAN 2
Cooling Fan 2
FAN 3
Cooling Fan 3
FOG
LAMP (GMC)
Fog Lamps (GMC)
HI BEAM
High-Beam
Headlamps
HID/
LO BEAM
High Intensity
Discharge (HID)
Low-Beam
Headlamps
HORN
Horn
IGN
Ignition Main
Relays
Usage
LT TRLR
STOP/TRN
Trailer Left
Stoplamp and Turn
Signal Lamp
PRK LAMP
Parking Lamp
PWR/TRN
Powertrain
RR DEFOG
Rear Window
Defogger
RT TRLR
STOP/TRN
Trailer Right
Stoplamp and Turn
Signal Lamp
Stop Lamps
(CHINA
ONLY)
Stop Lamps
(China Only)
TRLR
BCK/UP
Trailer Back-up
Lamps
WPR
Windshield Wiper
WPR HI
Windshield Wiper
High Speed
Instrument Panel Fuse
Block
The instrument panel fuse block is
under the instrument panel on the
passenger side of the vehicle. Pull
down on the cover to access the
fuse block.
Vehicle Care
261
Fuse Side
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Fuses
Usage
#
GMC NON HID =
Lo Beam
)
GMC NON HID =
High Shutter
) )
Chevy = Fog
Lamps
) ) )
Buick China =
Rear Fog Lamp
AIRBAG
Airbag
AMP
Amplifier
BCK
UP/STOP
Back-up Lamp/
Stoplamp
BCM
Body Control
Module
CNSTR
VENT
Canister Vent
CTSY
Courtesy Lamps
DR LCK
Door Locks
Fuses
Usage
DRL/
LO BEAM
Daytime Running
Lamps Relay/Low
Beam Headlamps
Relay
DSPLY
Display
FRT WSW
Front Windshield
Washer
HTD/
COOL SEAT
Heated/Cooling
Seats
HVAC
Heating,
Ventilation, and Air
Conditioning
INADV PWR
INT LAMPS
Inadvertent Power/
Interior Light Pipe
Lamps
INFOTMNT/
MSM
Infotainment/
Memory Seat
Module
LT TRN SIG
Driver Side Turn
Signal
OBS
DET/URS
Rear Park Assist/
Side Blind Zone
Alert/Forward
262
Vehicle Care
Fuses
Usage
Collision Alert/
Universal Remote
System
PDM
Power Mirrors,
Liftgate Release
PWR MODE
Power Mode
PWR MIR
Power Mirrors
RDO
Radio
REAR WPR
Rear Wiper
RT TRN SIG
Passenger Side
Turn Signal
STR WHL
ILLUM
Steering Wheel
Illumination
USB CHRG
USB Charging
Relay Side
Relays
Usage
LT/
PWR/SEAT
Driver Side Power
Seat Relay
RT/
PWR/SEAT
Passenger Side
Power Seat Relay
PWR/WNDW
Power Windows
Relay
PWR/
COLUMN
Power Steering
Column Relay
L/GATE
Liftgate Relay
LCK
Power Lock Relay
REAR/WSW
Rear Window
Washer Relay
UNLCK
Power Unlock
Relay
DRL/
LO BEAM
Daytime Running
Lamps Relay/
Low-Beam
Headlamps Relay
LT/UNLCK
Driver Side Unlock
Relay
Vehicle Care
297
For vehicles being dinghy towed,
the vehicle should be run at the
beginning of each day and at each
RV fuel stop for about five minutes.
This will ensure proper lubrication of
transmission components. Reinstall
the fuse to start the vehicle.
To tow the vehicle from the front
with all four wheels on the ground:
1.
Position the vehicle to be
towed, shift the transmission to
P (Park), and turn the ignition
to LOCK/OFF.
2.
Secure the vehicle to the
towing vehicle.
3.
Set the parking brake.
4.
Turn the ignition to ACC/
ACCESSORY.
5.
Shift the transmission to
N (Neutral).
6.
To prevent the battery from
draining while the vehicle is
being towed, remove the
15 amp ECM fuse and the
15 amp OnStar fuse. These
are in the battery compartment
behind the passenger seat on
the floor. Also, remove the
50 amp BATT1 fuse from the
underhood fuse block and
store all fuses in a safe
location. See
Engine
Compartment Fuse Block
0
257
.
7.
Release the parking brake.
Caution
If the vehicle is towed without
performing each of the steps
listed under
Dinghy Towing,
the
automatic transmission could be
damaged. Be sure to follow all
steps of the dinghy towing
procedure prior to and after
towing the vehicle.
Caution
If 105 km/h (65 mph) is exceeded
while towing the vehicle, it could
be damaged. Never exceed
105 km/h (65 mph) while towing
the vehicle.
Once the destination is reached:
1.
Set the parking brake.
2.
Reinstall the fuses.
3.
Shift the transmission to
P (Park), turn the ignition to
LOCK/OFF, and remove the
key from the ignition.
4.
Disconnect the vehicle from the
towing vehicle.
Caution
Do not tow a vehicle with the front
drive wheels on the ground if one
of the front tires is a compact
spare tire. Towing with two
different tire sizes on the front of
the vehicle can cause severe
damage to the transmission.
Instruments and Controls
99
Caution
Leaving electrical equipment
plugged in for an extended period
of time while the vehicle is off will
drain the battery. Always unplug
electrical equipment when not in
use and do not plug in equipment
that exceeds the maximum
20 amp rating.
Certain electrical accessories may
not be compatible with the
accessory power outlet and could
overload vehicle or adapter fuses.
If a problem is experienced, see
your dealer.
When adding electrical equipment,
be sure to follow the installation
instructions included with the
equipment. See
Add-On Electrical
Equipment
0
187
.
Caution
Hanging heavy equipment from
the power outlet can cause
damage not covered by the
vehicle warranty. The power
outlets are designed for
accessory power plugs only, such
as cell phone charge cords.
Power Outlet 110/120 Volt
Alternating Current
If equipped, this power outlet is on
the rear of the center console. It can
be used to plug in electrical
equipment that uses a maximum
limit of 150 watts.
An indicator light on the outlet turns
on to show it is in use. The light
comes on when the ignition is in
ON/RUN and equipment requiring
less than 150 watts is plugged into
the outlet, and no system fault is
detected.
The indicator light does not come on
when the ignition is in LOCK/OFF or
if the equipment is not fully seated
into the outlet.
If equipment is connected using
more than 150 watts or a system
fault is detected, a protection circuit
shuts off the power supply and the
indicator light turns off. To reset the
circuit, unplug the item and plug it
130
Lighting
Turn and Lane-Change
Signals
Move the lever all the way up or
down to signal a turn.
An arrow on the instrument cluster
will flash in the direction of the turn
or lane change.
Raise or lower the lever until the
arrow starts to flash to signal a lane
change. The turn signal flashes
three times.
The lever returns to its starting
position when it is released.
If after signaling a turn or lane
change the arrow flashes rapidly or
does not come on, a signal bulb
may be burned out. Replace any
burned out bulbs. If a bulb is not
burned out, check the fuse. See
Fuses and Circuit Breakers
0
215
.
Front Fog Lamps
If the vehicle is equipped with front
fog lamps, the button is on the
outboard side of the instrument
panel.
The ignition must be on to turn on
the fog lamps.
#
(Front Fog Lamps) :
Press to
turn the fog lamps on or off. An
indicator light on the instrument
cluster comes on when the fog
lamps are on.
The fog lamps come on together
with the parking lamps.
If the high-beam headlamps are
turned on, the fog lamps will turn off.
If the high-beam headlamps are
turned off, the fog lamps will turn
back on again.
Some localities have laws that
require the headlamps to be on
along with the fog lamps.
Vehicle Care
193
1.
Engine Air Cleaner/Filter
0
198
.
2.
Engine Oil Fill Cap. See
Engine Oil
0
195
.
3.
Engine Oil Dipstick. See
Engine Oil
0
195
.
4.
Engine Cooling Fan (Out of
View). See
Cooling System
0
200
.
5.
Engine Coolant Surge Tank
and Pressure Cap. See
Cooling System
0
200
.
6.
Brake Fluid Reservoir. See
Brakes
0
205
.
7.
Auxiliary Fuse Block. See
Engine Compartment Fuse
Block
0
215
.
8.
Battery - North America
0
207
.
9.
Windshield Washer Fluid
Reservoir. See
Washer Fluid
0
204
.
10.
Engine Compartment Fuse
Block
0
215
.
Vehicle Care
195
1.
Engine Air Cleaner/Filter
0
198
.
2.
Engine Oil Dipstick. See
Engine Oil
0
195
.
3.
Engine Cooling Fan (Out of
View). See
Cooling System
0
200
.
4.
Engine Oil Fill Cap. See
Engine Oil
0
195
.
5.
Engine Coolant Surge Tank
and Pressure Cap. See
Cooling System
0
200
.
6.
Brake Fluid Reservoir. See
Brakes
0
205
.
7.
Auxiliary Fuse Block. See
Engine Compartment Fuse
Block
0
215
.
8.
Battery - North America
0
207
.
9.
Windshield Washer Fluid
Reservoir. See
Washer Fluid
0
204
.
10.
Engine Compartment Fuse
Block
0
215
.
Engine Oil
To ensure proper engine
performance and long life, careful
attention must be paid to engine oil.
Following these simple, but
important steps will help protect
your investment:
.
Use engine oil approved to the
proper specification and of the
proper viscosity grade. See
Selecting the Right Engine Oil
in this section.
.
Check the engine oil level
regularly and maintain the
proper oil level. See
Checking
Engine Oil
and
When to Add
Engine Oil
in this section.
.
Change the engine oil at the
appropriate time. See
Engine Oil
Life System
0
197
.
.
Always dispose of engine oil
properly. See
What to Do with
Used Oil
in this section.
Checking Engine Oil
It is a good idea to check the engine
oil level at each fuel fill. In order to
get an accurate reading, the vehicle
must be on level ground. The
engine oil dipstick handle is a loop.
See
Engine Compartment Overview
0
192
for the location of the engine
oil dipstick.
Obtaining an accurate oil level
reading is essential:
1.
If the engine has been running
recently, turn off the engine and
allow several minutes for the oil
to drain back into the oil pan.
Checking the oil level too soon
after engine shutoff will not
provide an accurate oil level
reading.
{
Warning
The engine oil dipstick handle
may be hot; it could burn you.
Use a towel or glove to touch the
dipstick handle.
2.
Pull out the dipstick and wipe it
with a clean paper towel or
cloth, then push it back in all
the way. Remove it again,
keeping the tip down, and
check the level.
214
Vehicle Care
To replace one of these bulbs:
1.
Push the left end of the lamp
assembly toward the right.
2.
Turn the lamp assembly down
to remove it.
3.
Turn the bulb socket (1)
counterclockwise to remove it
from the lamp assembly (3).
4.
Pull the bulb (2) straight out of
the bulb socket (1).
5.
Push the replacement bulb
straight into the bulb socket
and turn the bulb socket
clockwise to install it into the
lamp assembly.
6.
Turn the lamp assembly into
the lamp assembly opening
engaging the clip side first.
7.
Push on the lamp side opposite
the clip until the lamp assembly
snaps into place.
Replacement Bulbs
Exterior Lamp
Bulb
Number
Back-Up Lamp
921
Front Parking Lamp
7444NA
Front Turn
Signal Lamp
7444NA
High-Beam
Headlamp
9005LL
License Plate Lamp
W5W LL
Low-Beam
Headlamp
H11 LL
For replacement bulbs not listed
here, contact your dealer.
Electrical System
Electrical System
Overload
The vehicle has fuses and circuit
breakers to protect against an
electrical system overload.
When the current electrical load is
too heavy, the circuit breaker opens
and closes, protecting the circuit
until the current load returns to
normal or the problem is fixed. This
greatly reduces the chance of circuit
overload and fire caused by
electrical problems.
Fuses and circuit breakers protect
power devices in the vehicle.
Replace a bad fuse with a new one
of the identical size and rating.
If there is a problem on the road and
a fuse needs to be replaced, the
same amperage fuse can be
borrowed. Choose some feature of
the vehicle that is not needed to use
and replace it as soon as possible.
Vehicle Care
215
Headlamp Wiring
An electrical overload may cause
the lamps to go on and off, or in
some cases to remain off. Have the
headlamp wiring checked right away
if the lamps go on and off or
remain off.
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected
from electrical overload, overload
due to heavy snow or ice may
cause wiper linkage damage.
Always clear ice and heavy snow
from the windshield before using the
windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Fuses and Circuit
Breakers
The wiring circuits in the vehicle are
protected from short circuits by a
combination of fuses and circuit
breakers. This greatly reduces the
chance of damage caused by
electrical problems.
To check a fuse, look at the
silver-colored band inside the fuse.
If the band is broken or melted,
replace the fuse. Be sure to replace
a bad fuse with a new one of the
identical size and rating.
Fuses of the same amperage can
be temporarily borrowed from
another fuse location, if a fuse goes
out. Replace the fuse as soon as
possible.
To identify and check fuses, circuit
breakers, and relays, see
Engine
Compartment Fuse Block
0
215
,
Instrument Panel Fuse Block
0
218
,
and
Rear Compartment Fuse Block
0
220
.
Engine Compartment
Fuse Block
To remove the fuse block cover,
squeeze the clip and lift it up.
Caution
Spilling liquid on any electrical
component on the vehicle may
damage it. Always keep the
covers on any electrical
component.
216
Vehicle Care
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Mini Fuses
Usage
1
Sunroof
2
Outside Rearview
Mirror Switch
3
Canister Vent
Solenoid
4
Not Used
5
Electronic Brake
Control Module
Valve
6
Intelligent Battery
Sensor
7
Not Used
8
Transmission
Control Module
Battery
9
Not Used
10
Fuel System Control
Module R/C/
Headlamp Leveling
11
Rear Wiper
12
Rear Window
Defogger
13
Not Used
Mini Fuses
Usage
14
Outside Rearview
Mirror Heater
15
Fuel System Control
Module Battery
16
Heated Seat
Module/Memory
Module
17
Transmission
Control Module R/C
18
Engine Control
Module R/C
19
Fuel Pump
20
Not Used
21
Fan Relay (Auxiliary
Fuse Block)
22
Not Used
23
Ignition Coil/Injectors
24
Washer Pump
25
Not Used
26
Canister Purge
Solenoid/Water
Valve Solenoid/
Oxygen Sensors
Vehicle Care
217
Mini Fuses
Usage
Pre and Post/Turbo
Wastegate Solenoid
(1.4L)/Turbo Bypass
Solenoid (1.4L)
27
Auxiliary
Heater Pump
28
Engine Control
Module Powertrain
Ignition 1
29
Engine Control
Module Powertrain
Ignition 2
30
Mass Air Flow
Sensor
31
Left High-Beam
Headlamp
32
Right High-Beam
Headlamp
33
Engine Control
Module Battery
34
Horn
35
Air Conditioning
Compressor Clutch
36
Front Fog Lamps
J-Case
Fuses
Usage
1
Electronic Brake
Control
Module Pump
2
Front Wiper
3
Blower Motor
4
IEC R/C
5
Not Used
6
Not Used
7
Starter Solenoid
(Automatic
Transmission), Not
Used (Manual
Transmission)
8
Cooling Fan
Low/Mid
9
Cooling Fan High
10
EVP
11
Pinion Starter
Solenoid (Automatic
Transmission),
Starter Solenoid
(Manual
Transmission)
U-Micro
Relays
Usage
2
Fuel Pump Power
4
Starter/Spare
HC-Micro
Relays
Usage
7
Starter/Pinion
Mini
Relays
Usage
1
Run Crank
3
Cooling Fan Mid
5
Powertrain Relay
8
Cooling Fan Low
HC-Mini
Relays
Usage
6
Cooling Fan High
218
Vehicle Care
Auxiliary Fuse Block
To remove the fuse block cover,
squeeze the clips and lift it up.
Caution
Spilling liquid on any electrical
component on the vehicle may
damage it. Always keep the
covers on any electrical
component.
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Relays
Usage
01
Electric
Vacuum Pump
02
Cooling Fan
Control 1
03
Cooling Fan
Control 2
04
Trailer (N/A)
Instrument Panel Fuse
Block
The instrument panel fuse block is
on the underside of the driver side
instrument panel. To access the
fuses, remove the storage
compartment. To remove the
storage compartment, open the
compartment and pull it out.
Vehicle Care
219
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Mini Fuses
Usage
1
Body Control
Module 1
2
Body Control
Module 2
3
Body Control
Module 3
4
Body Control
Module 4
5
Body Control
Module 5
6
Body Control
Module 6
7
Body Control
Module 7
8
Body Control
Module 8
9
Discrete Logic
Ignition Switch
10
Sensing Diagnostic
Module Battery
11
Data Link Connector
Mini Fuses
Usage
12
Heater, Ventilation,
and Air Conditioning
MDL/ICS
13
Liftgate Relay
14
UPA Module
15
LDW Module/Inside
Rearview Mirror
16
Adaptive Forward
Lighting Module
17
Power
WNDWSW DR
18
Rain Sensor
19
Body Control
Module Regulated
Voltage Control
20
Steering Wheel
Switch Backlighting
21
A/C Accessory
Power Outlet/
PRNDL
22
Cigar Lighter/DC
Accessory Power
Outlet
220
Vehicle Care
Mini Fuses
Usage
23
Spare
24
Spare
25
Spare
26
Automatic Occupant
Sensing Display
27
IPC/PTC Control/
Clutch Switch
28
Headlamp Switch/
AFL/DC Converter
29
Spare
30
Transmission
Control Module
Battery
31
IPC Battery
32
Radio/Chime/
Aux Jack
33
Display/Faceplate
34
OnStar/UHP/DAB
S/B Fuses
Usage
1
Spare
2
Spare
S/B Fuses
Usage
3
Power Window
Motor Front
4
Power Window
Motor Rear
5
Logistic Mode Relay
6
Spare
7
Spare
8
Spare
Circuit
Breaker
Usage
CB1
Spare
Midi Fuse
Usage
M01
PTC
Relays
Usage
01
Accessory/Retained
Accessory Power
02
Liftgate
03
Spare
04
Spare
Relays
Usage
05
Logistic Mode
Rear Compartment Fuse
Block
The rear compartment fuse block is
behind a cover on the left side of
the rear compartment. To access
the fuses, remove the cover.
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Vehicle Care
221
Mini Fuses
Usage
1
Driver Seat Power
Lumbar Switch
Mini Fuses
Usage
2
Passenger Seat
Power Lumbar
Switch
3
Amplifier
4
Trailer Socket (N/A)
5
All-Wheel Drive
Module
6
Automatic Occupant
Sensing Module
7
Spare/LPG Module
Battery
8
Trailer Parking
Lamps (N/A)
9
Spare
10
Spare/Side Blind
Zone Alert Module
11
Trailer Module (N/A)
12
Nav Dock
13
Heated Steering
Wheel
14
Trailer Socket (N/A)
15
Spare/EVP Switch
Mini Fuses
Usage
16
Water In Fuel
Sensor
17
Inside Rearview
Mirror/Rear Vision
Camera
18
Spare/LPG Module
Run/Crank
S/B Fuses
Usage
1
Driver Power Seat
Switch/Memory
Module
2
Passenger Power
Seat Switch
3
Trailer Module (N/A)
4
A/C-D/C Inverter
5
Battery
6
Headlamp Washer
7
DC/DC Source 1
8
DC/DC Source 2
9
Spare