Cadillac SRX - 2015 Fuse Box Diagram

Cadillac SRX - 2015 Fuse Box Diagram

Instruments and Controls
5-7
Caution (Continued)
equipment when not in use and
do not plug in equipment that
exceeds the maximum 20 ampere
rating.
Certain accessory power plugs may
not be compatible with the
accessory power outlet and could
overload vehicle or adapter fuses.
If a problem is experienced, see
your dealer.
When adding electrical equipment,
be sure to follow the proper
installation instructions included with
the equipment. See
Add-On
Electrical Equipment on page 9-68
.
{
Caution
Hanging heavy equipment from
the power outlet can cause
damage not covered by the
vehicle warranty. The power
(Continued)
Caution (Continued)
outlets are designed for
accessory power plugs only, such
as cell phone charge cords.
Cigarette Lighter
There may be a cigarette lighter
under the climate control system,
inside the front storage bin.
To activate the cigarette lighter,
push it into the heating element and
let go. The lighter pops out when it
is ready to be used.
{
Caution
Holding a cigarette lighter in while
it is heating does not let the
lighter back away from the
heating element when it is hot.
Damage from overheating can
occur to the lighter or heating
(Continued)
Caution (Continued)
element, or a fuse could be
blown. Do not hold a cigarette
lighter in while it is heating.
Ashtrays
There may be an ashtray under the
climate control system on the center
stack. Press the door to release the
ashtray.
To empty the ashtray, remove it from
the instrument panel by holding the
edges and pulling straight out. To
reinstall, push the tray back into
place.
There may also be ashtrays on the
center floor console behind the shift
lever and in the rear doors.
6-6
Lighting
lamps, and other exterior lamps
come on. The transition time for the
lamps coming on varies based on
wiper speed. When the wipers are
not operating, these lamps turn off.
Move the exterior lamp control to
P
or
;
to disable this feature.
Hazard Warning Flashers
|
(Hazard Warning Flashers):
Press this button on the instrument
panel to make the front and rear
turn signal lamps flash on and off.
This warns others that you are
having trouble. Press again to turn
the flashers off.
Turn and Lane-Change
Signals
Move the lever all the way up or
down to signal a turn.
An arrow on the instrument cluster
will flash in the direction of the turn
or lane change.
Raise or lower the lever until the
arrow starts to flash to signal a lane
change. The turn signal flashes
three times.
The lever returns to its starting
position when it is released.
If after signaling a turn or lane
change the arrow flashes rapidly or
does not come on, a signal bulb
may be burned out.
Replace any burned out bulbs. If a
bulb is not burned out, check the
fuse. See
Fuses and Circuit
Breakers on page 10-33
.
Front Fog Lamps
The front fog lamp button is on the
exterior lamp control on the
outboard side of the steering wheel.
The ignition must be on to turn on
the fog lamps.
10-6
Vehicle Care
1.
Engine Air Cleaner/Filter on
page 10-10
.
2.
Power Steering Reservoir and
Cap (Under Engine Cover). See
Power Steering Fluid on
page 10-18
.
3.
Engine Oil Fill Cap. See
Engine
Oil on page 10-7
.
4.
Engine Oil Dipstick (Out of
View). See
Engine Oil on
page 10-7
.
5.
Engine Cover on page 10-6
.
6.
Transmission Fluid Cap and
Dipstick (Out of View). See
Automatic Transmission Fluid on
page 10-10
.
7.
Brake Fluid Reservoir. See
Brakes on page 10-19
.
8.
Engine Coolant Surge Tank and
Pressure Cap. See
Engine
Coolant on page 10-13
.
9.
Battery (Out of View). See
Battery on page 10-21
.
10.
Remote Positive (+) Terminal.
See
Jump Starting on
page 10-78
.
11.
Remote Negative (
) Terminal
(Out of View). See
Jump
Starting on page 10-78
.
12.
Engine Compartment Fuse
Block on page 10-33
.
13.
Windshield Washer Fluid
Reservoir. See
Washer Fluid
on page 10-18
.
Engine Cover
1.
Oil Fill Cap
2.
Engine Cover Bolt
3.
Engine Cover
To remove:
1.
Remove the oil fill cap (1).
2.
Remove the engine cover
bolt (2).
3.
Raise the engine cover (3) to
release from the retainers.
4.
Lift and remove the engine
cover.
5.
Reverse Steps 1
4 to reinstall
engine cover.
10-32
Vehicle Care
4.
Turn the bulb socket (1)
counterclockwise to remove it
from the lamp assembly (3).
5.
Pull the bulb (2) straight out of
the bulb socket.
6.
Push the replacement bulb
straight into the bulb socket and
turn the bulb socket clockwise to
install into the lamp assembly.
7.
Turn the lamp assembly into the
liftgate, engaging the clip side
first.
8.
Push on the lamp side opposite
the clip until the lamp assembly
snaps into place.
Replacement Bulbs
Exterior Lamp
Bulb
Number
Back-up Lamp
Hyperclick
PH16W
Daytime
Running Lamp
7443 ULL
Headlamp
High-Beam
9005LL
Headlamp
Low-Beam
H11LL
License Plate Lamp
W5WLL
Turn Signal Front
7444NA
Tail/Turn
Signal Rear
7440
For replacement bulbs not listed
here, contact your dealer.
Electrical System
Electrical System
Overload
The vehicle has fuses and circuit
breakers to protect against an
electrical system overload.
When the current electrical load is
too heavy, the circuit breaker opens
and closes, protecting the circuit
until the current load returns to
normal or the problem is fixed. This
greatly reduces the chance of circuit
overload and fire caused by
electrical problems.
Fuses and circuit breakers protect
power devices in the vehicle.
Replace a bad fuse with a new one
of the identical size and rating.
If there is a problem on the road and
a fuse needs to be replaced, the
same amperage fuse can be
borrowed. Choose some feature of
the vehicle that is not needed to use
and replace it as soon as possible.
Vehicle Care
10-33
Headlamp Wiring
An electrical overload may cause
the lamps to go on and off, or in
some cases to remain off. Have the
headlamp wiring checked right away
if the lamps go on and off or
remain off.
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected
from electrical overload, overload
due to heavy snow or ice may
cause wiper linkage damage.
Always clear ice and heavy snow
from the windshield before using the
windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Fuses and Circuit
Breakers
The wiring circuits in the vehicle are
protected from short circuits by a
combination of fuses and circuit
breakers. This greatly reduces the
chance of damage caused by
electrical problems.
To check a fuse, look at the
silver-colored band inside the fuse.
If the band is broken or melted,
replace the fuse. Be sure to replace
a bad fuse with a new one of the
identical size and rating.
Fuses of the same amperage can
be temporarily borrowed from
another fuse location, if a fuse goes
out. Replace the fuse as soon as
possible.
To identify and check fuses, circuit
breakers, and relays, see
Engine
Compartment Fuse Block on
page 10-33
,
Instrument Panel Fuse
Block on page 10-36
, and
Rear
Compartment Fuse Block on
page 10-38
.
Engine Compartment
Fuse Block
To remove the fuse block cover,
press the clips on the cover and lift
it straight up.
{
Caution
Spilling liquid on any electrical
component on the vehicle may
damage it. Always keep the
covers on any electrical
component.
10-34
Vehicle Care
Engine Compartment Fuse Block
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
J-Case
Fuses
Usage
6
Wiper
12
Vacuum Pump
J-Case
Fuses
Usage
24
Antilock Brake
System Pump
25
Rear Electrical
Center 1
J-Case
Fuses
Usage
26
Rear Electrical
Center 2
41
Cooling Fan 2
42
Starter
45
Cooling Fan 1
Mini Fuses
Usage
1
Engine Control
Module Battery
2
Transmission
Control Module
Battery
5
Engine Control
Module Run Crank
7
Post-Catalytic
Converter O2
Sensor
8
Pre-Catalytic
Converter O2
Sensor
Vehicle Care
10-35
Mini Fuses
Usage
9
Engine Control
Module Powertrain
10
Fuel Injectors
Even
11
Fuel Injectors
Odd
13
Washer
14
Heated Steering
Wheel
15
Not Used
16
Instrument Cluster/
Malfunction Indicator
Lamp/Ignition
17
Air Quality Sensor
18
Not Used
19
Transmission
Control Module Run
Crank
20
Rear Electrical
Center Run Crank
30
Switch Back Light
Mini Fuses
Usage
32
Battery Sense
(Regulated Voltage
Control)
33
Adaptive Forward
Lighting
35
Electronic Brake
Control Module
36
Air Conditioning
Compressor Clutch
46
Low-Beam
Headlamp
Right
47
Low-Beam
Headlamp
Left
50
Front Fog Lamps
51
Horn
52
Fuel System Control
Module
53
Headlamp Level
54
Sensing Diagnostic
Module Ignition
Mini Fuses
Usage
55
High-Beam
Headlamp
Right
56
High-Beam
Headlamp
Left
57
Ignition Steering
Column Lock
65
Trailer Right
Stoplamp
66
Trailer Left Stoplamp
67
Spare
68
Spare
69
Spare
70
Spare
71
Spare
72
Spare
10-36
Vehicle Care
Mini Relays
Usage
7
Powertrain
9
Cooling Fan 2
13
Cooling Fan 1
15
Run/Crank
Micro
Relays
Usage
2
Vacuum Pump
4
Wiper Control
5
Wiper Speed
10
Starter
12
Cool Fan 3
14
Low Beam/HID
U Micro
Relays
Usage
3
Air Conditioning
Compressor Clutch
8
Not Used
Instrument Panel Fuse
Block
The instrument panel fuse block is
located in the center console
between the driver and passenger
seats. To access the fuses, open
the fuse panel door from the
passenger side by pulling it out.
To reinstall the door, push the door
back into its original location.
The vehicle may not be equipped
with all of the fuses, relays and
features shown.
Vehicle Care
10-37
Instrument Panel Fuse Block
Mini Fuses
Usage
DISPLY
Display
S/ROOF
Sunroof
UHP
Universal
Handsfree Phone
(If Equipped)
RDO
Radio
APO
IP/CNSL
Auxiliary Power
Outlet
Instrument
Panel/Console
APO
CNSL
Auxiliary Power
Outlet
Floor
Console
BCM 1
Body Control
Module 3
BCM 4
Body Control
Module 4
BCM 7
Body Control
Module 7
ONSTAR
OnStar
®
System (If
Equipped)
RAIN SNSR
Rain Sensor
10-38
Vehicle Care
Mini Fuses
Usage
BCM 6
Body Control
Module 6
ESCL
Electronic Steering
Column Lock
AIRBAG
Sensing and
Diagnostic Module
DLC
Data Link
Connector
IPC
Instrument Cluster
STR
WHL SW
Steering Wheel
Switch
BCM 3
Body Control
Module 1
BCM 2
Body Control
Module 2
AMP/RDO
Amplifier/Radio
HVAC
Heating Ventilation
& Air Conditioning
J-Case
Fuses
Usage
BCM 8
Body Control
Module 8
FRT BLWR
Front Blower
Relays
Usage
LOGIC RLY/
SHUNT
Logistics Relay/
Shunt
RAP/
ACCY RLY
Retained
Accessory Power/
Accessory Relay
Breakers
Usage
HTR DR
Heated Driver Seat
HTR PAS
Heated
Passenger Seat
Rear Compartment Fuse
Block
The rear compartment fuse block is
in the cargo area, on the driver side
of the vehicle behind the lower trim
panel. To open, turn the latch with a
flat bladed tool and pull the trim
panel from the edges to fold it down.
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Vehicle Care
10-39
Rear Compartment Fuse Block
Fuses
Usage
AOS MDL
Automatic Occupant
Sensing Module
AUX PWR
Auxiliary Power
Outlet
* BCM
THEFT
Body Control
Module Theft
CAMERA
Rear Vision Camera
CNSTR
VENT
Canister Vent
DRV
PWR SEAT
Driver Power Seat
EOCM/
SBZA
External Object
Calculating Module/
Side Blind Zone
Alert
EMPTY
Not Used
FRT
HTD SEAT
Front Heated Seats
FRT
VENT SEAT
Front Ventilated
Seats
FUEL
PUMP
Fuel Pump
10-40
Vehicle Care
Fuses
Usage
HTD MIR
Heated Mirror
IGN/
THEFT 1
Ignition/Theft 1
IGN/
THEFT 2
Ignition/Theft 2
INFOTMNT
Infotainment
* L/GATE
Liftgate
LGM
Liftgate Module
LGM
LOGIC
Liftgate Module
Logic
MDL TRLR
Trailer Module
MIR
WDO MDL
Mirror Window
Module
PRK
BRK MDL
Park Brake Module
PASS DR
WDO SW
Passenger Door
Window Switch
PASS DR
PWR SEAT
Passenger/Driver
Power Seats
PRK
LPS TRLR
Trailer Park Lamps
Fuses
Usage
RDM
Rear Drive Module
REAR
DEFOG
Rear Defog
REAR
HTD SEAT
Rear Heated Seats
REAR/WPR
Rear Wiper
RT WDO
Right Window
RPA MDL
Rear Parking Assist
Module
SADS MDL
Semi Active
Damping System
Module
* SEC
Security
SHUNT
Shunt
SPARE
Not Used
SPARE
FUSES
Spare Fuses
* TRLR EXP
Trailer Export
TRLR
Trailer Module
* TRLR 2
Trailer 2
Fuses
Usage
UGDO
Universal Garage
Door Opener
VICS
Vehicle Information
Communications
System (Export)
WNDO
Power Window
Relays
Usage
DEFOG
REAR
Rear Window
Defogger
* FUEL
PUMP
Fuel Pump
LOGIC
Logistic Relay
(Export)
* RUN RLY
Run Relay
SPARE
Not Used
WPR
CONTRL
Wiper Control
*Denotes uplevel content.