Cadillac Escalade ESV - 2012 Fuse Box Diagram

Cadillac Escalade ESV - 2012 Fuse Box Diagram

2-14
Keys, Doors, and Windows
If you set off the alarm by accident,
press unlock on the RKE transmitter
or place the key in the ignition and
turn it to START to turn off the
alarm. The alarm will not stop if you
try to unlock a door any other way.
Testing the Alarm
To test the alarm:
1.
From inside the vehicle, lower
the driver window and open the
driver door.
2.
Activate the system by locking
the doors with the power door
lock switch while the door is
open, or with the RKE
transmitter.
3.
Get out of the vehicle, close the
door and wait for the security
light to go out.
4.
Then reach in through the
window, unlock the door with the
manual door lock and open the
door. This should set off the
alarm.
While the alarm is set, the power
door unlock switch will not work.
If the alarm does not sound when it
should but the headlamps flash,
check to see if the horn works. The
horn fuse may be blown. To replace
the fuse, see
Fuses and Circuit
Breakers on page 10
39
.
If the alarm does not sound or the
headlamps do not flash, the vehicle
should be serviced by your dealer.
Immobilizer
See
Radio Frequency Statement on
page 13
21
for information
regarding Part 15 of the Federal
Communications Commission (FCC)
rules and Industry Canada
Standards RSS-GEN/210/220/310.
Immobilizer Operation
This vehicle has PASS-Key
®
III+
(Personalized Automotive Security
System) theft-deterrent system.
PASS-Key III+ is a passive
theft-deterrent system.
The system is automatically armed
when the key is removed from the
ignition.
The system is automatically
disarmed when the key is turned to
ON/RUN, ACC/ACCESSORY,
or START from the LOCK/OFF
position.
You do not have to manually arm or
disarm the system.
The security light will come on if
there is a problem with arming or
disarming the theft-deterrent
system.
When the PASS-Key III+ system
senses that someone is using the
wrong key, it prevents the vehicle
from starting. Anyone using a
trial-and-error method to start the
Keys, Doors, and Windows
2-15
vehicle will be discouraged because
of the high number of electrical key
codes.
If the engine does not start and the
security light on the instrument
panel cluster comes on when trying
to start the vehicle, there may be a
problem with the theft-deterrent
system. Turn the ignition off and try
again.
If the engine still does not start, and
the key appears to be undamaged,
try another ignition key. At this time,
you may also want to check the
fuse. See
Fuses and Circuit
Breakers on page 10
39
. If the
engine still does not start with the
other key, the vehicle needs service.
If the vehicle does start, the first key
may be faulty. See your dealer who
can service the PASS-Key III+ to
have a new key made.
It is possible for the PASS-Key III+
decoder to learn the transponder
value of a new or replacement key.
Up to 10 keys may be programmed
for the vehicle. The following
procedure is for programming
additional keys only. If all the
currently programmed keys are lost
or do not operate, you must see
your dealer or a locksmith who can
service PASS-Key III+ to have keys
made and programmed to the
system.
See your dealer or a locksmith who
can service PASS-Key III+ to get a
new key blank cut exactly as the
ignition key that operates the
system.
To program the new additional key:
1.
Verify that the new key has a
1
stamped on it.
2.
Insert the original, already
programmed key in the ignition
and start the engine. If the
engine will not start, see your
dealer for service.
3.
After the engine has started, turn
the key to LOCK/OFF, and
remove the key.
4.
Insert the new key to be
programmed and turn it to the
ON/RUN position within
five seconds of turning the
ignition to the LOCK/OFF
position in Step 3.
The security light will turn off
once the key has been
programmed.
5.
Repeat Steps 1 through 4 if
additional keys are to be
programmed.
If you lose or damage your
PASS-Key III+ key, see your dealer
or a locksmith who can service
PASS-Key III+ to have a new
key made.
Do not leave the key or device that
disarms or deactivates the
theft-deterrent system in the vehicle.
5-8
Instruments and Controls
Power Outlets
The accessory power outlets can be
used to plug in electrical equipment,
such as a cell phone or MP3 player.
The vehicle has three accessory
power outlets located:
.
Inside the floor console
storage bin.
.
On the rear of the floor console.
.
In the rear cargo area on the
passenger side.
Remove the cover to use and
replace when not in use.
The accessory power outlets are
powered, even when the ignition is
in LOCK/OFF. Continuing to use
power outlets while the ignition is in
LOCK/OFF may cause the vehicle's
battery to run down.
{
WARNING
Power is always supplied to the
outlets. Do not leave electrical
equipment plugged in when the
vehicle is not in use because the
vehicle could catch fire and cause
injury or death.
Notice:
Leaving electrical
equipment plugged in for an
extended period of time while
the vehicle is off will drain the
battery. Always unplug electrical
equipment when not in use and
do not plug in equipment that
exceeds the maximum 20 ampere
rating.
Certain power accessory plugs
may not be compatible with the
accessory power outlet and could
overload adapter or vehicle fuses.
If a problem is experienced, see
your dealer.
When adding electrical equipment,
be sure to follow the proper
installation instructions included
with the equipment. Do not use
equipment exceeding the
maximum amperage rating of
20 amperes. See
Add-On Electrical
Equipment on page 9
69
.
Notice:
Hanging heavy
equipment from the power
outlet can cause damage not
covered by the vehicle warranty.
The power outlets are designed
for accessory power plugs only,
such as cell phone charge cords.
Instruments and Controls
5-9
Power Outlet 110 Volt
Alternative Current
The vehicle may have a power
outlet that can be used to plug in
electrical equipment that uses a
maximum limit of 150 watts.
The power outlet is located on the
rear of the center console.
An indicator light on the outlet turns
on to show it is in use. The light
comes on when the ignition is in
ON/RUN and equipment requiring
less than 150 watts is plugged into
the outlet, and no system fault is
detected.
If equipment is connected using
more than 150 watts or a system
fault is detected, a protection circuit
shuts off the power supply and the
indicator light turns off. To reset the
circuit, unplug the item and plug it
back in or turn the Remote
Accessory Power (RAP) off and
then back on. See
Retained
Accessory Power (RAP) on
page 9
26
.
The power outlet is not designed for
and may not work properly, if the
following are plugged in:
.
Equipment with high initial
peak wattage such as:
compressor-driven refrigerators
and electric power tools.
.
Other equipment requiring
an extremely stable
power supply such as:
microcomputer-controlled
electric blankets, touch sensor
lamps, etc.
Cigarette Lighter
For vehicles with a cigarette lighter,
it is located in the center console
near the cupholders. Press on the
access door to open it and use the
lighter.
To use the cigarette lighter, push it
in all the way, and let go. When it is
ready, it will pop back out by itself.
Notice:
Holding a cigarette lighter
in while it is heating does not let
the lighter back away from the
heating element when it is hot.
Damage from overheating can
occur to the lighter or heating
element, or a fuse could be
blown. Do not hold a cigarette
lighter in while it is heating.
Lighting
6-7
The regular headlamp system can
be turned on when needed.
Hazard Warning Flashers
|
(Hazard Warning Flashers):
Press this button located on top of
the steering column, to make the
front and rear turn signal lamps
flash on and off. This warns others
that you are having trouble. Press
again to turn the flashers off.
When the hazard warning flashers
are on, the vehicle's turn signals will
not work.
Turn and Lane-Change
Signals
An arrow on the instrument panel
cluster flashes in the direction of the
turn or lane change.
Move the turn signal lever all the
way up or down to signal a turn.
Raise or lower the lever until the
arrow starts to flash to signal a lane
change. The turn signals
automatically flash three times.
It will flash six times if the tow-haul
mode is active. Holding the turn
signal lever for more than
one second causes the turn signals
to flash until the lever is released.
The lever returns to its starting
position when it is released.
If after signaling a turn or a lane
change the arrows flash rapidly or
do not come on, a signal bulb may
be burned out.
Have the bulbs replaced. If the bulb
is not burned out, check the fuse.
See
Instrument Panel Fuse Block
on page 10
43
and
Engine
Compartment Fuse Block on
page 10
39
.
Turn Signal On Chime
If the turn signal is left on for more
than 1.2 km (0.75 mi), a chime
sounds at each flash of the turn
signal and the message TURN
SIGNAL ON also appears in the
DIC. See
Lamp Messages on
page 5
32
. To turn the chime and
message off, move the turn signal
lever to the off position.
Driving and Operating
9-25
prevent possible vehicle
component damage. When this
happens, hold the ignition switch
in the START position to
continue engine cranking.
Notice:
Cranking the engine for
long periods of time, by returning
the key to the START position
immediately after cranking has
ended, can overheat and damage
the cranking motor, and drain the
battery. Wait at least 15 seconds
between each try, to let the
cranking motor cool down.
2.
If the engine does not start after
5-10 seconds, especially in very
cold weather (below
18°C or
0°F), it could be flooded with too
much gasoline. Try pushing the
accelerator pedal all the way to
the floor and holding it there as
you hold the key in START for
up to a maximum of 15 seconds.
Wait at least 15 seconds
between each try, to allow the
cranking motor to cool down.
When the engine starts, let go of
the key and accelerator. If the
vehicle starts briefly but then
stops again, repeat these steps.
This clears the extra gasoline
from the engine. Do not race the
engine immediately after starting
it. Operate the engine and
transmission gently until the oil
warms up and lubricates all
moving parts.
Notice:
If you add electrical parts
or accessories, you could change
the way the engine operates. Any
resulting damage would not be
covered by the vehicle warranty.
See
Add-On Electrical Equipment
on page 9
69
.
Engine Heater
The engine coolant heater can
provide easier starting and better
fuel economy during engine
warm-up in cold weather conditions
at or below
18°C (0°F). Vehicles
with an engine heater should be
plugged in at least four hours before
starting. An internal thermostat in
the plug-end of the cord may exist
which will prevent engine coolant
heater operation at temperatures
above
18°C (0°F).
To Use the Engine Coolant
Heater
1.
Turn off the engine.
2.
Open the hood and unwrap the
electrical cord. The cord is
secured to the engine
compartment fuse block with a
clip. Carefully remove the wire
tie which secures the electrical
cord. Do not cut the
electrical cord.
Driving and Operating
9-67
Trailer Brakes
A loaded trailer that weighs more
than 900 kg (2,000 lbs) needs to
have its own brake system that is
adequate for the weight of the
trailer. Be sure to read and follow
the instructions for the trailer brakes
so they are installed, adjusted and
maintained properly.
Do not tap into the vehicle's
hydraulic system.
Trailer Wiring Harness
Heavy-Duty Trailer Wiring Harness
Package
The vehicle has a seven-pin
universal heavy-duty trailer
connector attached to the rear
bumper beam next to the integrated
trailer hitch.
The seven-wire harness contains
the following trailer circuits:
.
Yellow: Left Stop/Turn Signal
.
Dark Green: Right Stop/Turn
Signal
.
Brown: Taillamps
.
White: Ground
.
Light Green: Back-up Lamps
.
Red: Battery Feed*
.
Dark Blue: Trailer Brake*
*The fuses for these two circuits are
installed in the underhood electrical
center, but the wires are not
connected. They should be
connected by your dealer or a
qualified service center.
If charging a remote (non-vehicle)
battery, press the tow/haul mode
button located at the end of the shift
lever. This will boost the vehicle
system voltage and properly charge
the battery. If the trailer is too light
for tow/haul mode, turn on the
Vehicle Care
10-7
A.
Engine Air Cleaner/Filter on
page 10
13
.
B.
Coolant Surge Tank and
Pressure Cap. See
Cooling
System on page 10
15
.
C.
Remote Positive (+) Terminal.
See
Jump Starting on
page 10
88
.
D.
Battery on page 10
27
.
E.
Remote Negative (
) Terminal
(Out of View). See
Jump
Starting on page 10
88
.
F.
Automatic Transmission
Dipstick (Out of View). See
Checking the Fluid Level
under
Automatic Transmission
Fluid on page 10
10
.
G.
Engine Oil Fill Cap. See
When
to Add Engine Oil
under
Engine Oil on page 10
7
.
H.
Engine Oil Dipstick (Out of
View). See
Checking Engine
Oil
under
Engine Oil on
page 10
7
.
I.
Engine Cooling Fans (Out of
View). See
Cooling System on
page 10
15
.
J.
Power Steering Fluid Reservoir.
See
Power Steering Fluid on
page 10
22
.
K.
Brake Master Cylinder
Reservoir. See
Brake Fluid
under
Brake Fluid on
page 10
25
.
L.
Engine Compartment Fuse
Block on page 10
39
.
M.
Windshield Washer Fluid
Reservoir. See
Adding Washer
Fluid
under
Washer Fluid on
page 10
23
.
If the vehicle is a hybrid, see the
hybrid supplement for more
information.
Engine Oil
To ensure proper engine
performance and long life, careful
attention must be paid to engine oil.
Following these simple, but
important steps will help protect
your investment:
.
Always use engine oil approved
to the proper specification and of
the proper viscosity grade. See
Selecting the Right Engine Oil
in this section.
.
Check the engine oil level
regularly and maintain the
proper oil level. See
Checking
Engine Oil
and
When to Add
Engine Oil
in this section.
.
Change the engine oil at the
appropriate time. See
Engine Oil
Life System on page 10
9
.
.
Always dispose of engine oil
properly. See
What to Do with
Used Oil
in this section.
10-38
Vehicle Care
Electrical System
Electrical System
Overload
The vehicle has fuses and circuit
breakers to protect against an
electrical system overload.
When the current electrical load is
too heavy, the circuit breaker opens
and closes, protecting the circuit
until the current load returns to
normal or the problem is fixed. This
greatly reduces the chance of circuit
overload and fire caused by
electrical problems.
Fuses and circuit breakers protect
power devices in the vehicle.
Replace a bad fuse with a new one
of the identical size and rating.
If there is a problem on the road and
a fuse needs to be replaced, the
same amperage fuse can be
borrowed. Choose some feature of
the vehicle that is not needed to use
and replace it as soon as possible.
Headlamp Wiring
An electrical overload may cause
the lamps to go on and off, or in
some cases to remain off. Have the
headlamp wiring checked right away
if the lamps go on and off or
remain off.
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected
from electrical overload, overload
due to heavy snow or ice may
cause wiper linkage damage.
Always clear ice and heavy snow
from the windshield before using the
windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Vehicle Care
10-39
Fuses and Circuit
Breakers
If the vehicle is a hybrid, see the
hybrid supplement for more
information.
The wiring circuits in the vehicle are
protected from short circuits by a
combination of fuses, circuit
breakers and fusible thermal links.
This greatly reduces the chance of
fires caused by electrical problems.
Look at the silver-colored band
inside the fuse. If the band is broken
or melted, replace the fuse. Be sure
you replace a bad fuse with a new
one of the identical size and rating.
If you ever have a problem on the
road and don't have a spare fuse,
you can borrow one that has the
same amperage. Just pick some
feature of your vehicle that you can
get along without
like the radio or
accessory power outlet
and use its
fuse, if it is the correct amperage.
Replace it as soon as you can.
Engine Compartment
Fuse Block
The Engine Compartment Fuse
Block is located in the engine
compartment, on the driver side of
the vehicle. Lift the cover for access
to the fuse/relay block.
If the vehicle is a hybrid, see the
hybrid supplement for more
information.
Notice:
Spilling liquid on any
electrical component on the
vehicle may damage it. Always
keep the covers on any electrical
component.
To remove fuses, hold the end of
the fuse between your thumb and
index finger and pull straight out.
Vehicle Care
10-41
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Fuses
Usage
1
Right Trailer Stop/
Turn Lamp
2
Electronic Stability
Suspension Control,
Automatic Level
Control Exhaust
3
Left Trailer Stop/
Turn Lamp
4
Engine Controls
5
Engine Control
Module, Throttle
Control
6
Trailer Brake
Controller
7
Front Washer
8
Oxygen Sensors
9
Antilock Brakes
System 2
Fuses
Usage
10
Trailer Back-up
Lamps
11
Driver Side
Low-Beam Headlamp
12
Engine Control
Module (Battery)
13
Fuel Injectors, Ignition
Coils (Right Side)
14
Transmission Control
Module (Battery)
15
Vehicle Back-up
Lamps
16
Passenger Side
Low-Beam Headlamp
17
Air Conditioning
Compressor
18
Oxygen Sensors
19
Transmission Controls
(Ignition)
20
Fuel Pump
Fuses
Usage
21
Fuel System Control
Module
22
Headlamp Washer
23
Rear Windshield
Washer
24
Fuel Injectors, Ignition
Coils (Left Side)
25
Trailer Parking Lamps
26
Driver Side Parking
Lamps
27
Passenger Side
Parking Lamps
28
Fog Lamps
29
Horn
30
Passenger Side
High-Beam Headlamp
31
Daytime Running
Lamps (DRL)
(If Equipped)
32
Driver Side
High-Beam Headlamp
10-42
Vehicle Care
Fuses
Usage
33
Daytime Running
Lamps 2 (If Equipped)
34
Sunroof
35
Key Ignition System,
Theft Deterrent
System
36
Windshield Wiper
37
SEO B2 Upfitter
Usage (Battery)
38
Electric Adjustable
Pedals
39
Climate Controls
(Battery)
40
Airbag System
(Ignition)
41
Amplifier
42
Audio System
43
Miscellaneous
(Ignition), Cruise
Control
44
Liftgate Release
Fuses
Usage
45
Airbag System
(Battery)
46
Instrument Panel
Cluster
47
Not Used
48
Auxiliary Climate
Control (Ignition)
49
Center High-Mounted
Stoplamp (CHMSL)
50
Rear Defogger
51
Heated Mirrors
52
SEO B1 Upfitter
Usage (Battery)
53
Accessory Power
Outlet, Cigarette
Lighter (If Equipped)
54
Automatic Level
Control Compressor
Relay
55
Climate Controls
(Ignition)
Fuses
Usage
56
Engine Control
Module, Secondary
Fuel Pump (Ignition)
J-Case
Fuses
Usage
57
Cooling Fan 1
58
Automatic Level
Control Compressor
59
Heavy Duty Antilock
Braking System
60
Cooling Fan 2
61
Antilock Brake
System 1
62
Starter
63
Stud 2 (Trailer
Brakes)
64
Left Bussed Electrical
Center 1
65
Electric Running
Boards
Vehicle Care
10-43
J-Case
Fuses
Usage
66
Not Used
67
Transfer Case
68
Stud 1 (Trailer
Connector Battery
Power)
69
Mid-Bussed Electrical
Center 1
70
Climate Control
Blower
71
Power Liftgate
Module
72
Left Bussed Electrical
Center 2
Relays
Usage
FAN HI
Cooling Fan High
Speed
FAN LO
Cooling Fan Low
Speed
Relays
Usage
FAN
CNTRL
Cooling Fan Control
HDLP
LO/HID
Low-Beam Headlamp
FOG
LAMP
Front Fog Lamps
A/C
CMPRSR
Air Conditioning
Compressor
STRTR
Starter
PWR/TRN
Powertrain
FUEL
PMP
Fuel Pump
PRK
LAMP
Parking Lamps
REAR
DEFOG
Rear Defogger
RUN/
CRNK
Switched Power
Instrument Panel Fuse
Block
The instrument panel fuse block
access door is located on the driver
side edge of the instrument panel.
Pull off the cover to access the fuse
block.
10-44
Vehicle Care
The vehicle may not be equipped
with all of the fuses, relays, and
features shown.
Fuses
Usage
1
Rear Seats
2
Rear Accessory
Power Outlet
Fuses
Usage
3
Steering Wheel
Controls Backlight
4
Driver Door Module
5
Dome Lamps, Driver
Side Turn Signal
Fuses
Usage
6
Driver Side Turn
Signal, Stoplamp
7
Instrument Panel
Back Lighting
8
Passenger Side Turn
Signal, Stoplamp
9
Passenger Door
Module, Driver Unlock
10
Power Door Lock 2
(Unlock Feature)
11
Power Door Lock 2
(Lock Feature)
12
Stoplamps, Center
High
Mounted
Stoplamp
13
Rear Climate Controls
14
Power Mirror
15
Body Control
Module (BCM)
16
Accessory Power
Outlets
Vehicle Care
10-45
Fuses
Usage
17
Interior Lamps
18
Power Door Lock 1
(Unlock Feature)
19
Rear Seat
Entertainment
20
Ultrasonic Rear
Parking Assist, Power
Liftgate
21
Power Door Lock 1
(Lock Feature)
22
Driver Information
Center (DIC)
23
Rear Wiper
24
Cooled Seats
25
Driver Seat Module,
Remote Keyless Entry
System
26
Driver Power Door
Lock (Unlock Feature)
Circuit
Breaker
Usage
LT DR
Driver Side Power
Window Circuit
Breaker
Harness
Connector
Usage
LT DR
Driver Door
Harness
Connection
BODY
Harness Connector
BODY
Harness Connector
Center Instrument Panel Fuse
Block
The center instrument panel fuse
block is located underneath the
instrument panel, to the left of the
steering column.
Top View
Harness
Connector
Usage
BODY 2
Body Harness
Connector 2
BODY 1
Body Harness
Connector 1
BODY 3
Body Harness
Connector 3
HEADLINER 3
Headliner
Harness
Connector 3