Cadillac SRX - 2010 Fuse Box Diagram

Cadillac SRX - 2010 Fuse Box Diagram

4-12
Instruments and Controls
There is a small cap that must be
removed to access the accessory
power outlet. When not using the
outlet be sure to cover it with the
protective cap.
Notice:
Leaving electrical
equipment plugged in for an
extended period of time while
the vehicle is off will drain the
battery. Power is always supplied
to the outlets. Always unplug
electrical equipment when not in
use and do not plug in equipment
that exceeds the maximum
20 ampere rating.
Certain accessory power plugs may
not be compatible to the accessory
power outlet and could result in
blown vehicle or adapter fuses.
If you experience a problem,
see your dealer for additional
information on the accessory
power outlets.
Notice:
Adding any electrical
equipment to the vehicle can
damage it or keep other
components from working as
they should. The repairs would
not be covered by the vehicle
warranty. Do not use equipment
exceeding maximum amperage
rating of 20 amperes. Check with
your dealer before adding
electrical equipment.
Follow the proper installation
instructions that are included with
any electrical equipment you install.
Notice:
Improper use of the
power outlet can cause damage
not covered by the vehicle
warranty. Do not hang any type
of accessory or accessory
bracket from the plug because
the power outlets are designed
for accessory power plugs only.
Cigarette Lighter
There may be a cigarette lighter
located under the climate control
system, inside the front storage bin.
To activate the cigarette lighter,
push it into the heating element and
let go. The lighter pops out when it
is ready to be used.
Notice:
Holding a cigarette lighter
in while it is heating does not let
the lighter back away from the
heating element when it is hot.
Damage from overheating can
occur to the lighter or heating
element, or a fuse could be
blown. Do not hold a cigarette
lighter in while it is heating.
Lighting
5-5
See
Vehicle Personalization
on
page 4
41
to select the delay time.
You can also select no delay time.
If the ignition is turned off with the
exterior lamp control in the parking
lamp or headlamp position, the
Twilight Sentinel
®
delay will not
occur. The lamps will turn off as
soon as the control is turned off.
The regular headlamp system
should be turned on when needed.
Hazard Warning Flashers
|
Hazard Warning Flasher:
Press this button located on the
instrument panel near the audio
system, to make the front and rear
turn signal lamps flash on and off.
This warns others that you are
having trouble. Press again to turn
the flashers off.
Turn and Lane-Change
Signals
An arrow on the instrument panel
cluster will flash in the direction of
the turn or lane change.
Move the lever all the way up or
down to signal a turn.
Raise or lower the lever until the
arrow starts to flash to signal a lane
change. The turn signal flashes
three times.
The lever returns to its starting
position when it is released.
If after signaling a turn or lane
change the arrow flashes rapidly or
does not come on, a signal bulb
may be burned-out.
Have the bulbs replaced. If the bulb
is not burned out, check the fuse.
See
Fuses and Circuit Breakers
on
page 9
44
for more information.
Vehicle Care
9-7
A.
Engine Air Cleaner/Filter
on
page 9
14
.
B.
Power Steering Reservoir and
Cap. See
Power Steering Fluid
on page 9
22
.
C.
Engine Oil Fill Cap. See
Engine
Oil on page 9
10
.
D.
Engine Oil Dipstick (Out of
View). See
Engine Oil
on
page 9
10
.
E.
Brake Master Cylinder
Reservoir. See
Brakes
on
page 9
24
.
F.
Battery (Out of View). See
Battery on page 9
27
.
G.
Engine Coolant Surge Tank and
Pressure Cap. See
Engine
Coolant on page 9
17
.
H.
Remote Positive (+) Terminal.
See
Jump Starting
on
page 9
101
.
I.
Remote Negative (
) Terminal
(Out of View). See
Jump
Starting on page 9
101
.
J.
Engine Compartment Fuse
Block on page 9
45
.
K.
Windshield Washer Fluid
Reservoir. See
Washer Fluid
on
page 9
23
.
Vehicle Care
9-9
A.
Engine Air Cleaner/Filter
on
page 9
14
.
B.
Power Steering Reservoir and
Cap (Under engine cover). See
Power Steering Fluid
on
page 9
22
.
C.
Engine Oil Fill Cap. See
Engine
Oil on page 9
10
.
D.
Engine Oil Dipstick (Out of
View). See
Engine Oil
on
page 9
10
.
E.
Engine Cover on page 9
9
.
F.
Transmission Fluid Cap and
Dipstick. See
Automatic
Transmission Fluid
on
page 9
13
.
G.
Brake Master Cylinder
Reservoir. See
Brakes
on
page 9
24
.
H.
Engine Coolant Surge Tank and
Pressure Cap. See
Engine
Coolant on page 9
17
.
I.
Battery (Out of View). See
Battery on page 9
27
.
J.
Remote Positive (+) Terminal.
See
Jump Starting
on
page 9
101
.
K.
Remote Negative (
) Terminal
(Out of View). See
Jump
Starting on page 9
101
.
L.
Engine Compartment Fuse
Block on page 9
45
.
M.
Windshield Washer Fluid
Reservoir. See
Washer Fluid
on
page 9
23
.
Engine Cover
Engine Cover (3.0 L V6)
To remove:
1.
Remove the oil fill cap (A).
2.
Raise the engine cover (B) to
release from the retainers.
3.
Lift and remove the engine
cover.
4.
Reverse Steps 1 through 3 to
reinstall engine cover.
9-44
Vehicle Care
Electrical System
Electrical System
Overload
The vehicle has fuses and circuit
breakers to protect against an
electrical system overload.
When the current electrical load is
too heavy, the circuit breaker opens
and closes, protecting the circuit
until the current load returns to
normal or the problem is fixed. This
greatly reduces the chance of circuit
overload and fire caused by
electrical problems.
Fuses and circuit breakers protect
the following in the vehicle:
.
Headlamp Wiring
.
Windshield Wiper Motor
.
Power Windows and Other
Power Accessories
Replace a bad fuse with a new one
of the identical size and rating.
If there is a problem on the road and
a fuse needs to be replaced, the
same amperage fuse can be
borrowed. Choose some feature of
the vehicle that is not needed to use
and replace it as soon as possible.
Headlamp Wiring
An electrical overload may cause
the lamps to go on and off, or in
some cases to remain off. Have the
headlamp wiring checked right away
if the lamps go on and off or
remain off.
Windshield Wipers
If the wiper motor overheats due to
heavy snow or ice, the windshield
wipers will stop until the motor cools
and will then restart.
Although the circuit is protected
from electrical overload, overload
due to heavy snow or ice may
cause wiper linkage damage.
Always clear ice and heavy snow
from the windshield before using the
windshield wipers.
If the overload is caused by an
electrical problem and not snow or
ice, be sure to get it fixed.
Fuses and Circuit
Breakers
The wiring circuits in the vehicle are
protected from short circuits by a
combination of fuses and circuit
breakers. This greatly reduces the
chance of damage caused by
electrical problems.
To check a fuse, look at the
silver-colored band inside the fuse.
If the band is broken or melted,
replace the fuse. Be sure to replace
a bad fuse with a new one of the
identical size and rating.
Fuses of the same amperage can
be temporarily borrowed from
another fuse location, if a fuse goes
out. Replace the fuse as soon as
you can.
Vehicle Care
9-45
To identify and check fuses, circuit
breakers, and relays, see
Engine
Compartment Fuse Block
on
page 9
45
and
Rear Compartment
Fuse Block on page 9
49
.
Engine Compartment
Fuse Block
To remove the fuse block cover,
press the clips on the cover and lift
it straight up.
The vehicle might not have all the
fuses and features listed.
Notice:
Spilling liquid on any
electrical component on the
vehicle may damage it. Always
keep the covers on any electrical
component.
Engine Compartment Fuse Block
J-Case
Fuses
Usage
6
Wiper
12
Vacuum Pump
24
Anitlock Brake
System Pump
J-Case
Fuses
Usage
25
Rear Electrical
Center 1
26
Rear Electrical
Center 2
27
Not Used
9-46
Vehicle Care
J-Case
Fuses
Usage
41
Cooling Fan 2
42
Starter
43
Not Used
44
Not Used
45
Cooling Fan 1
59
Secondary
AIR Pump
Mini Fuses
Usage
1
Engine Control
Module Battery
2
Transmission
Control Module
Battery
3
Mass Air Flow
Sensor
4
Not Used
5
Engine Control
Module Run Crank
Mini Fuses
Usage
7
Post
Catalytic
Converter O2
Sensor
8
Pre
Catalytic
Converter O2
Sensor
9
Engine Control
Module Powertrain
10
Fuel Injectors
Even
11
Fuel Injectors
Odd
13
Washer
16
Instrument Panel
Cluster/Malfunction
Indicator Lamp/
Ignition
17
Air Quality Sensor
18
Headlamp Washer
19
Transmission
Control Module Run
Crank
20
Rear Electrical
Center Run Crank
Mini Fuses
Usage
23
Heater Motor
30
Switch Back Light
32
Battery Sense
(Regulated Voltage
Control)
33
Adaptive Forward
Lighting / Adaptive
Headlamp Leveling
Module
34
Body Control
Module 7
35
Electronic Brake
Control Module
46
Low Beam
Headlamp
Right
47
Low Beam
Headlamp
Left
50
Front Fog Lamps
51
Horn
52
Fuel System Control
Module
Vehicle Care
9-47
Mini Fuses
Usage
53
Headlamp Level
54
Sensing Diagnostic
Module Ignition
55
High Beam
Headlamp
Right
56
High Beam
Headlamp
Left
57
Ignition Steering
Column Lock
65
Trailer Right
Stop Lamp
66
Trailer Left
Stop Lamp
67
Spare
Mini Fuses
Usage
68
Spare
69
Spare
70
Spare
71
Spare
72
Spare
Mini Relays
Usage
7
Powertrain
9
Cooling Fan 2
13
Cooling Fan 1
15
Run/Crank
16
Secondary
AIR Pump
Micro
Relays
Usage
2
Vacuum Pump
4
Wiper Control
5
Wiper Speed
10
Starter
12
Cool Fan 3
14
Low Beam/HID
U Micro
Relays
Usage
8
Headlamp Washer
9-48
Vehicle Care
Instrument Panel Fuse
Block
The instrument panel fuse block is
located in the center console
between the driver and passenger
seats. To access the fuses, open
the fuse panel door from the
passenger side by pulling it out.
To reinstall the door, push the door
back into its original location.
Instrument Panel Fuse Block
Mini Fuses
Usage
DISPLY
Display
S/ROOF
Sun Roof
SPARE
Spare
UHP
Universal
Handsfree Phone
RDO
Radio
APO
IP
Auxiliary Power
Outlet
Instrument
Panel
APO
CNSL
Auxiliary Power
Outlet
Floor
Console
BCM 3
Body Control
Module 3
BCM 4
Body Control
Module 4
BCM 5
Body Control
Module 5
ONSTAR
OnStar
®
System
Vehicle Care
9-49
Mini Fuses
Usage
RAIN SNSR
Rain Sensor
BCM 6
Body Control
Module 6
ESCL
Electronic Steering
Column Lock
AIRBAG
Sensing and
Diagnostic Module
DLC
Data Link
Connection
IPC
Instrument Panel
Cluster
SPARE
Not Used
BCM 1
Body Control
Module 1
BCM 2
Body Control
Module 2
Mini Fuses
Usage
AMP/RDO
Amplifier/Radio
HVAC
Heating Ventilation
& Air Conditioning
J
Case
Fuses
Usage
BCM 8
Body Control
Module 8
FRT BLWR
Front Blower
Relays
Usage
LOGIC RLY
Logistics Relay
RAP/
ACCY RLY
Retained
Accessory Power/
Accessory Relay
Rear Compartment Fuse
Block
The rear compartment fuse block is
located in the cargo area, on the
driver side of the vehicle behind the
lower trim panel. To open, turn the
latch with a flat bladed tool and pull
the trim panel from the edges to fold
it down.
The vehicle may not be equipped
with all of the fuses and relays
shown.
9-50
Vehicle Care
Rear Compartment Fuse Block
Fuses
Usage
SPARE
FUSES
Spare Fuses
AOS MDL
Automatic Occupant
Sensing Module
SPARE
Not Used
SPARE
Not Used
SPARE
Not Used
PASS DR
WDO SW
Passenger Door
Window Switch
DRV
PWR SEAT
Driver Power Seat
PASS DR
PWR SEAT
Passenge/Driver
Power Seats
MDL TRLR
Trailer Module
RPA MDL
Rear Parking Assist
Module
RDM
Rear Drive Module
PRK
LPS TRLR
Trailer Park Lamps
FUEL
PUMP
Fuel Pump
Fuses
Usage
* SEC
Security
INFOTMNT
Infotainment
* TRLR EXP
Trailer Export
WPR REAR
Rear Wiper
MIR
WDO MDL
Mirror Window
Module
* SPARE
Not Used
CNSTR
VENT
Canister Vent
LGM
LOGIC
Lift Gate Module
Logic
CAMERA
Rear Vision Camera
FRT
VENT SEAT
Front Ventilated
Seats
TRLR MDL
Trailer Module
SADS MDL
Semi Active
Damping System
Module
RR
HTD SEAT
Rear Heated Seats
Vehicle Care
9-51
Fuses
Usage
FRT
HTD SEAT
Front Heated Seats
THEFT
HORN
Theft Horn
* LGATE
Liftgate
REAR
DEFOG
Rear Defog
* BCM
THEFT
Body Control
Module Theft
* TRLR 2
Trailer 2
UGDO
Universal Garage
Door Opener
RT WDO
Right Window
PRK
BRK MDL
Park Brake Module
Fuses
Usage
SPARE
Not Used
LT WDO
Left Window
IGN/
THEFT 1
Ignition/Theft 1
LGATE
MDL
Liftgate Module
IGN/
THEFT 2
Ignition/Theft 2
SPARE
Not Used
HTD MIR
Heated Mirror
AUX PWR
Auxiliary Power
Outlet
Relays
Usage
SPARE
Not Used
* FUEL
PUMP
Fuel Pump
WPR
CONTRL
Wiper Control
* RUN RLY
Run Relay
LOGIC
Logistic Relay
DEFOG
REAR
Rear Window
Defogger
*
Denotes up
level content.
Vehicle Care
9-107
3.
With the vehicle OFF, press the
brake pedal and press the
START/STOP switch to start the
engine (the green LED on the
switch will illuminate).
4.
Put the vehicle in N (Neutral).
5.
Press the START/STOP switch
again. The engine will stop, the
DIC will display Shift to Park and
the amber LED on the switch
illuminates. See
Transmission
Messages on page 4
40
.
6.
Remove the following fuses:
BCM 1, BCM 2 and BCM 3. The
START/STOP switch LED's will
be off. See
Instrument Panel
Fuse Block on page 9
48
.
7.
Close the drivers door.
Notice:
If the vehicle is towed
without performing each of the
steps listed under
Dinghy
Towing,
the automatic
transmission could be damaged.
Be sure to follow all steps of the
dinghy towing procedure prior to
and after towing the vehicle.
Once the destination has been
reached:
1.
Shift the vehicle to P (Park).
2.
Reinstall the BCM fuses. See
Instrument Panel Fuse Block
on
page 9
48
.
3.
Disconnect the vehicle from the
tow vehicle.
Notice:
Too much or too
little fluid can damage the
transmission. Be sure that the
transmission fluid is at the proper
level before towing with all four
wheels on the ground.
Notice:
Do not tow a vehicle with
the front drive wheels on the
ground if one of the front tires is
a compact spare tire. Towing with
two different tire sizes on the
front of the vehicle can cause
severe damage to the
transmission.
Dolly Towing
(All-Wheel
Drive Vehicles)
All-wheel
drive vehicles should not
be towed with two wheels on the
ground. To properly tow these
vehicles, they should be placed on
a platform trailer with all four wheels
off of the ground or dinghy towed
from the front. See Dinghy Towing
earlier in this section.