Cadillac XLR-V - 2009 Fuse Box Diagram

Cadillac XLR-V - 2009 Fuse Box Diagram

Arming the System
To arm the system:
Press
Q
on the keyless access transmitter.
Open the door. Lock the door with the power door
lock switch. The security light should flash. Remove
the keyless access transmitter from the interior of the
vehicle and close the door. The security light will stop
flashing and stay on. After 30 seconds, the light
should turn off.
The vehicle can be programmed to automatically lock
the doors and arm the system when you exit the
vehicle. See
DIC Vehicle Personalization on
page 3-72
.
Now, if a door or the trunk lid is opened without the
keyless access transmitter, the alarm will go off.
The horn will sound for two minutes, then it will go
off to save battery power. And, the vehicle will not
start without a keyless transmitter present.
The theft-deterrent system will not arm if you lock the
driver door with the power door lock switch after
the doors are closed.
If the passenger stays in the vehicle when you leave with
the keyless access transmitter, have the passenger lock
the vehicle after the doors are closed. This way the alarm
will not arm, and the passenger will not set it off.
Testing the Alarm
To test the system:
1. Close the trunk lid.
2. Lower the window on the driver door.
3. Manually arm the system.
4. Close the doors and wait 30 seconds.
5. Reach through the open window and manually pull
the release lever on the floor.
6. Turn off the alarm by pressing
K
on the transmitter.
If the alarm is inoperative, check to see if the horn
works. If not, check the horn fuse. See
Fuses and Circuit
Breakers on page 6-83
. If the horn works, but the
alarm doesn’t go off, see your dealer/retailer.
Disarming the System
Always use the keyless access transmitter to unlock a
door either by pressing
K
on the transmitter or by
squeezing the door handle sensor while you have the
transmitter with you. Unlocking a door any other way will
set off the alarm. If the alarm sounds, press
K
on the
keyless access transmitter to disarm it.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
2-21
Immobilizer Operation
The vehicle has a passive theft-deterrent system.
The system is automatically armed when the ignition is
turned off.
The immobilization system is disarmed when the ignition
is turned to OFF/ACCESSORY or START and a valid
transmitter is found in the vehicle.
You do not have to manually arm or disarm the system.
The security light comes on if there is a problem with
arming or disarming the theft-deterrent system.
The system has one or more keyless access transmitters
that are matched to an immobilizer control unit in the
vehicle. Only a correctly matched keyless access
transmitter starts the vehicle. The vehicle may not
start if the keyless access transmitter is damaged.
If the engine does not start and the security light comes
on, there may be a problem with the immobilizer system.
Press the START button again.
If the vehicle does not start and the keyless access
transmitter appears to be undamaged, try another
keyless access transmitter. Or, place the transmitter in
the transmitter pocket. See “NO FOBS DETECTED”
under
DIC Warnings and Messages on page 3-60
for
additional information. Check the fuse. See
Fuses and
Circuit Breakers on page 6-83
. If the engine still does not
start with the other transmitter, the vehicle needs service.
If the engine does start, the first transmitter may be faulty.
See your dealer/retailer or have a new keyless access
transmitter programmed to the vehicle.
The immobilizer system can learn new or replacement
keyless access transmitters. Up to four keyless access
transmitters can be programmed for the vehicle.
To program additional transmitters, see “Matching
transmitter(s) to Your Vehicle” under
Keyless Access
System Operation on page 2-5
.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
2-23
If after signaling a turn or a lane change the arrows
flash rapidly or do not come on, a signal bulb could be
burned out.
Have the bulbs replaced. If the bulb is not burned out,
check the fuses. See
Fuses and Circuit Breakers
on page 6-83
.
Turn Signal on Chime
A chime will remind you if the turn signal is left on for
more than 3/4 mile (1.2 km) of driving.
If you need to leave the turn signal on for more than
3/4 mile (1.2 km), turn off the signal and then turn it
back on.
Headlamp High/Low-Beam Changer
Push the turn signal lever all the way forward to
change the headlamps from low beam to high beam.
When the high beams are on, this light
$
appears on
the instrument panel cluster.
Pull the lever rearward to change the headlamps back
to low beam.
Flash-to-Pass
This feature lets you use the high-beam headlamps to
signal the driver in front of you that you want to pass.
Pull and hold the turn signal lever toward you to use.
When you do, the following will occur:
If the low-beam headlamps are on, the high-beam
headlamps will turn on. They will stay on as long as
you hold the lever there. Release the lever to turn
them off.
If the headlamps are on high-beam, they will switch
to low-beam. To return to high beam, push the lever
away from you.
Windshield Wipers
The windshield wiper lever is located on the right side of
the steering column.
3-8
To adjust the HUD so you can see it properly, do the
following:
1. Adjust the seat to a comfortable driving position.
If you change the seat position later, you may
have to re-adjust the HUD.
2. Start the engine and press the top or bottom of the
HUD button to center the HUD image in your view.
The HUD image can only be adjusted up and
down, not side-to-side.
3. Press the DIMMER button until the DIC reads
HUD DIMMING. Then use the brightness button
to adjust the desired intensity.
The brightness of the HUD image is determined by the
light conditions in the direction the vehicle is facing
and where you have the HUD set. If you are facing a
dark object or a heavily shaded area, the HUD may
anticipate that you are entering a dark area and may
begin to dim.
To turn off the HUD, press the brightness button down
until the image disappears.
Polarized sunglasses could make the HUD image
harder to see.
As light shines out from the HUD, it is possible for light
to shine back in. In rare occurrences, when the sun
is at a specific angle and position, the sun’s rays can
shine back into the HUD. When this occurs, the display
device within the HUD will be temporarily illuminated.
The event will end when the vehicle’s angle to the
sun changes.
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity
of the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry
it. Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you cannot see the HUD image,
check to see if:
Something is covering the HUD unit.
The brightness is adjusted properly.
The HUD image is adjusted to the proper height.
Ambient light in the direction the vehicle is facing
is low.
A fuse is blown. See
Fuses and Circuit Breakers
on page 6-83
.
Keep in mind that the windshield is part of the HUD
system. See
Windshield Replacement on page 6-45
.
3-33
The following Adaptive Cruise Control (ACC) messages
may appear in the HUD:
CRUISE SPEED LIMITED:
This message indicates that
the vehicle speed has been reduced below the set
speed due to ACC limitations. The set speed is too high
and ACC cannot detect other vehicles at far enough
distances for the system to operate properly.
TIGHT CURVE:
This message indicates that ACC
has reduced the vehicle speed due to a tight curve in
the road. Once the road straightens, ACC will return to
the selected set speed or follow distance setting.
See “Adaptive Cruise Control (ACC)” under
Turn
Signal/Multifunction Lever on page 3-7
for more
information.
You may also see an ACC active symbol, alert symbol
or vehicle ahead symbol. See “Adaptive Cruise
Control (ACC)” under
Turn Signal/Multifunction Lever
on page 3-7
for more information.
Accessory Power Outlet(s)
The accessory power outlet can be used to connect
electrical equipment, such as a cellular phone.
The accessory power outlet is located inside the center
console storage compartment, on the forward left side.
To use the outlet, remove the tethered cap. When not
using it, always cover the outlet with the protective cap.
Notice:
When using an accessory power outlet,
maximum electrical load must not exceed 20 amps.
Always turn off any electrical equipment when
not in use. Leaving electrical equipment on for
extended periods will drain your vehicle’s battery.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience
a problem, see your dealer/retailer for additional
information on accessory power outlets.
3-34
Notice:
Adding any electrical equipment to the
vehicle can damage it or keep other components
from working as they should. The repairs would not
be covered by the vehicle warranty. Do not use
equipment exceeding maximum amperage rating of
20 amperes. Check with your dealer/retailer before
adding electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
We recommend that you see a qualified technician or
your dealer/retailer for the proper installation of the
equipment.
Notice:
Improper use of the power outlet can cause
damage not covered by the warranty. Do not hang
any type of accessory or accessory bracket from the
plug because the power outlets are designed for
accessory power plugs only.
Ashtray(s) and Cigarette Lighter
The ashtray and cigarette lighter are located under a
lid in the front console to the right of the shift lever.
Press the left side of the lid and it will open
automatically.
To use the cigarette lighter, push it in all the way and
let go. When it is ready, it will pop back out by itself.
Notice:
If papers, pins, or other flammable
items are put in the ashtray, hot cigarettes or other
smoking materials could ignite them and possibly
damage the vehicle. Never put flammable items
in the ashtray.
Notice:
Holding a cigarette lighter in while it is
heating does not let the lighter back away from the
heating element when it is hot. Damage from
overheating can occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
3-35
A. Battery. See
Battery on page 6-35
.
B. Passenger Compartment Air Filter. See
Passenger
Compartment Air Filter on page 3-41
.
C. Underhood Fuse Block. See
Underhood Fuse Block
on page 6-87
.
D. Power Steering Fluid. See
Power Steering Fluid on
page 6-30
.
E. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 6-20
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 6-15
.
G. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 6-15
.
H. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 6-32
.
I. Engine Coolant Surge Tank and Pressure Cap.
See
Cooling System on page 6-22
.
J. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 6-31
.
6-13
A. Battery. See
Battery on page 6-35
.
B. Passenger Compartment Air Filter. See
Passenger
Compartment Air Filter on page 3-41
.
C. Underhood Fuse Block. See
Underhood Fuse Block
on page 6-87
.
D. Power Steering Fluid. See
Power Steering Fluid on
page 6-30
.
E. Engine Air Cleaner/Filter. See
Engine Air
Cleaner/Filter on page 6-20
.
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under
Engine Oil on page 6-15
.
G. Engine Oil Dipstick. See “Checking Engine Oil”
under
Engine Oil on page 6-15
.
H. Brake Master Cylinder Reservoir. See “Brake Fluid”
under
Brakes on page 6-32
.
I. Engine Coolant Surge Tank and Pressure Cap.
See
Cooling System on page 6-22
.
J. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under
Windshield Washer Fluid
on page 6-31
.
Engine Oil
If the LOW OIL LEVEL or LOW OIL PRESSURE
message on the Driver Information Center (DIC)
appears, check the engine oil level right away.
For more information, see LOW OIL LEVEL and
LOW OIL PRESSURE under
DIC Warnings and
Messages on page 3-60
. Check the engine oil level
regularly; this is an added reminder.
Checking Engine Oil
It is a good idea to check the engine oil every time you
get fuel. In order to get an accurate reading, the oil
must be warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop. See
Engine Compartment Overview on page 6-12
for
the location of the engine oil dipstick.
1. Turn off the engine and give the oil several minutes
to drain back into the oil pan. If you do not do this,
the oil dipstick might not show the actual level.
2. Pull out the dipstick and clean it with a paper towel
or cloth, then push it back in all the way. Remove it
again, keeping the tip down, and check the level.
6-15
Windshield Wiper Fuses
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow or ice, the wiper will stop until the motor cools.
If the overload is caused by some electrical problem,
and not snow or ice, be sure to get it fixed.
Power Windows and Other Power
Options
Circuit breakers in the fuse block protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and
closes, protecting the circuit until the problem is fixed or
goes away.
Fuses and Circuit Breakers
The wiring circuits in the vehicle are protected from
short circuits by a combination of fuses, circuit breakers
and fusible thermal links. This greatly reduces the
chance of fires caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
Fuses of the same amperage can be temporarily
borrowed from another fuse location, if a fuse goes out.
Replace the fuse as soon as you can.
Instrument Panel Fuse Block
The panel fuse block is located on the passenger side
of the vehicle, under the instrument panel and under the
toe-board.
Remove the carpet and toe-board covering to access
the fuse block by pulling at the top of each corner
of the panel. Then turn the fuse block door knob
counterclockwise and pull the door to access the fuses.
6-83
Fuses
Usage
ACCA/DRIV
DR SW
Adaptive Cruise Control (ACC),
Driver Door Switch
AUX PWR
Auxiliary Power
Fuses
Usage
BTSI SOL/COL
LOCK
Brake Transmission Shift Interlock
Solenoid, Column Lock
CIGAR LTR
Cigar Lighter
6-84
Fuses
Usage
CLSTR/HUD
Instrument Panel Cluster, Heads-up
Display (HUD)
COLUMN LK
MDL
Not Used
DECK LID
CLOSE/PRK/
BRK B
Trunk Close Button, Parking Brake
Solenoid B
DR LOCKS
Door Locks
ECM
Engine Control Module
EMPTY
Not Used
EMPTY
Not Used
EMPTY
Not Used
EMPTY
Not Used
EMPTY
Not Used
FOLDING
TOP/TRUNK
LATCH
Retractable Hardtop, Trunk Latch
FUSE PULLER
Fuse Puller
GMLAN
DEVICES
GMLAN Devices
HTD STR WHL
Heated Steering Wheel
HTD/SEAT LH
Driver Side Heated Seat
HTD/SEAT RH
Passenger Side Heated Seat
HVAC/PWR
SND
Climate Control System, Power
Sounder
Fuses
Usage
IGN SW/INTR
SNSR
Ignition Switch, Intrusion Sensor
INTERIOR
LIGHTS
Interior Lights
ISRVM/HVAC
Inside Rearview Mirror, Climate
Control System, Column Lock,
Power Sounder
ONSTAR
OnStar
®
PRK/BRK
SOL A
Parking Brake Solenoid A
PWR FLDG
MIR-EXT/RET
Power Folding Mirror
PWR LUMBAR
LH/RH
Power Lumbar
RADIO/S-BAND/
VICS
Radio, S-Band, CD Changer
REAR
FOG/ALDL
Rear Fog Lamps, Diagnostic Link
Connector
REVERSE
LAMP
Reverse Lamp
REVERSE
LAMPS
Reverse Lamps
RPA/H/C
SEAT/WPR
RELAYS
Rear Park Aid, Heated/Cooled
Seats, Windshield Wiper Relays
RUN/ACSRY
PWR
Run, Accessory Power
6-85
Fuses
Usage
RUN/CRANK
Starter/Crank
SDM/PSIR SW
Airbags
SPARE FUSE
HOLDER
Spare Fuse
SPARE FUSE
HOLDER
Spare Fuse
SPARE FUSE
HOLDER
Spare Fuse
SPARE FUSE
HOLDER
Spare Fuse
STOP LAMP
Stoplamp
STR WHL
DIMMING
Steering Wheel Control Button
Lights
TILT/TELE
SW/MEM SEAT
MOD/TOP SW
Power Tilt Wheel, Telescopic
Steering Column, Memory Seat,
Driver Seat Switch, Retractable
Hardtop Switch
TUTD
SW/STRG
COL SW
Tap-Up/Tap-Down Switch
WPR DWELL
Rainsense™
Relays
Usage
PRK/BRK
HOLD
Park Brake Hold
PRK/BRK
RELEASE
Park Brake Release
F/MIR
RETRACT
Not Used
FOG RR
Not Used
F/MIR EXTEND
Not Used
FUEL DR
Fuel Door
Circuit
Breakers
Usage
PWR SEAT
Power Seats
DR CNTRLS
Door Controls
6-86
Underhood Fuse Block
The underhood fuse block
is located next to the
engine on the passenger
side of the vehicle.
For more information on
location, see
Engine
Compartment Overview on
page 6-12
.
Notice:
Spilling liquid on any electrical components
on the vehicle may damage it. Always keep the
covers on any electrical component.
To access the fuses, push in the tab located at the end
of the fuse block cover. Then lift the cover open.
Fuses
Usage
1
Antilock Brake System, Electronic
Suspension Control, Adaptive
Forward Lighting System (AFS)
2
Horn
3
Adaptive Cruise Control (ACC),
Transmission Controls
6-87
Fuses
Usage
4
Windshield Wipers
5
Stop/Back-Up Lamps
6
Oxygen Sensor
7
Battery 5
8
Parking Lamps
9
Electronic Throttle Control
10
Fuel Pump
11
Antilock Brake System
12
Odd Injectors
13
Electronic Suspension Control
14
Emission Controls
15
Air Conditioning Compressor
16
Even Injectors
17
Windshield Washer, Adaptive
Forward Lighting System (AFS),
Intercooler Pump
18
Headlamp Washer
Fuses
Usage
19
Right Low Beam Headlamp
20
Not Used
21
Left Low Beam Headlamp
22
Fog Lamp
23
Right High Beam Headlamp
24
Left High Beam Headlamp
25
Cooling Fan
26
Battery 3
27
Antilock Brakes
28
Climate Controls
29
Battery 2
30
Starter
31
Audio Amplifier
32
Not Used
33
Battery 1
48
Spare
6-88
Fuses
Usage
49
Spare
50
Spare
51
Spare
52
Spare
53
Not Used
54
Fuse Puller
56
Engine Control Module,
Transmission Control Module
Relays
Usage
34
Horn
35
Air Conditioning Compressor
36
Windshield Washer
37
Parking Lamps
38
Fog Lamps
39
High Beam Headlamps
Relays
Usage
40
Rear Window Defogger
41
Windshield Wiper High/Low
42
Wiper RUN/ACCESSORY Power
43
Starter/Crank
44
Ignition 1
45
Windshield Wiper On/Off
46
Headlamp Washer
47
Low Beam Headlamps
55
Fuel Pump
Diodes
Usage
§
Diode 1
§
Wiper Diode
§
Diode 2
6-89